DEPARTMENT OF

LABOR AND INDUSTRIES

Flagger means a person who provides temporary traffic control.

For the purposes of this chapter, MUTCD means the Federal Highway Administration's Manual on Uniform Traffic Control as currently modified and adopted by the Washington state department of transportation.

(1) General requirements for signaling and flaggers.

(a) Employers must first apply the requirements in this section. Then you must set up and use temporary traffic controls according to the guidelines and recommendations in Part VI of the MUTCD.

(b) Job site workers with specific traffic control responsibilities must be trained in traffic control techniques, device usage, and placement.

Note:

• You may purchase copies of the MUTCD by writing:

U.S. Government Printing Office

Superintendent of Documents

Mail Stop: SSOP,

Washington D.C. 20402-9328

• ((You may)) To view and print a copy of the MUTCD ((at the following web site)) go to http://www.wsdot.wa.gov/((biz/trafficoperations/mutcd.htm)) and type MUTCD into the search box.

(2) When to use flaggers.

(a) Flaggers are to be used only when other reasonable traffic control methods will not adequately control traffic in the work zone.

(b) If signs, signals, and barricades do not provide necessary protection from traffic at work zones and construction sites on or adjacent to a highway or street, then you must use flaggers or other appropriate traffic controls.

(3) Flagger signaling.

(a) Flagger signaling must be with sign paddles approved by WSDOT and conform to guidelines and recommendations of MUTCD.

(b) Sign paddles must comply with the requirements of the MUTCD.

(c) When flagging is done during periods of darkness, sign paddles must be retroreflective or illuminated in the same manner as signs.

(d) During emergency situations, red flags, meeting the specifications of the MUTCD, may be used to draw a driver's attention to particularly hazardous conditions. In nonemergency situations, a red flag may be held in a flagger's free hand to supplement the use of a sign paddle.

(4) Adequate warning of approaching vehicles. Employers must:

• Position work zone flaggers so they are not exposed to traffic or equipment approaching them from behind.

– If this is not possible, then the employer, responsible contractor, and/or project owner must develop and use a method to ensure that flaggers have adequate visual warning of traffic and equipment approaching from behind.

• The department recognizes the importance of adequately trained flaggers and supports industry efforts to improve the quality of flagger training. However, training alone is not sufficient to comply with the statutory requirement of revising flagger safety standards to improve options available that ensure flagger safety and that flaggers have adequate visual warning of objects approaching from behind them.

(5) High-visibility garments for flaggers.

(a) While flagging during daylight hours, a flagger must at least wear, as an outer garment:

• A high-visibility safety garment designed according to Class 2 specifications in ANSI/ISEA 107-1999, American National Standard for High-Visibility Safety Apparel.

– Consisting of at least 775 square inches of background material that are fluorescent yellow-green, fluorescent orange-red or fluorescent red in color;

– 201 square inches of retroreflective material that encircles the torso and is placed to provide 360 degrees visibility around the flagger.

• A high visibility hard hat that is white, yellow, yellow-green, orange or red in color.

For the purpose of this rule, hours of darkness means one-half hour before sunset to one-half hour after sunrise.

(b) While flagging during hours of darkness, a flagger must at least wear, as an outer garment:

• A high-visibility safety garment designed according to Class 2 specifications in ANSI/ISEA 107-1999.

– Consisting of at least 775 square inches of background material that are fluorescent yellow-green, fluorescent orange-red or fluorescent red in color;

– 201 square inches of retroreflective material that encircles the torso and is placed to provide 360 degrees visibility around the flagger.

• White coveralls, or other coveralls or trousers that have retroreflective banding on the legs designed according to ANSI/ISEA 107-1999 standards.

• When snow or fog limit visibility, pants, coveralls, or rain gear, meeting these additional requirements must be worn:

- In a highly visible color;

– With retroreflective banding on the legs;

– Designed according to ANSI/ISEA 107-1999.

• A high-visibility hard hat:

– Marked with at least 12 square inches of retroreflective material applied to provide 360 degrees of visibility.

(6) Flagger training. Employers must make sure that:

(a) Each flagger has in their possession:

• A valid Washington traffic control flagger card; or

• A valid flagger card from a state such as:

– Oregon;

– Idaho;

– Montana;

– Other states having a flagger training reciprocity agreement with Washington.

(b) The flagger card shows the following:

• Verification that the flagger training required is completed;

• Date the flagger received their flagger training;

• Name of the instructor providing the flagger training;

• Name of the state that issued the flagger card;

• The card's expiration date, not to exceed three years from the date of issuance;

• The flagger's picture or a statement that says "valid with photo ID."

(c) Flagger training is based upon the MUTCD.

For the purpose of this rule, emergency means an unforeseen occurrence endangering life, limb, or property.

(7) Flagger orientation and traffic control plan.

(a) The employer, responsible contractor or project owner must conduct an orientation that familiarizes the flagger with the job site. This requirement applies each time the flagger is assigned to a new project or when job site conditions change significantly.

The orientation must include, but is not limited to:

• The flagger's role and location on the job site;

• Motor vehicle and equipment in operation at the site;

• Job site traffic patterns;

• Communications and signals to be used between flaggers and equipment operators;

• On-foot escape route;

• Other hazards specific to the job site.

(b) If flaggers are used on a job that will last more than one day, then the employer, responsible contractor and/or project owner must keep on-site, a current site specific traffic control plan. The purpose of this plan is to help move traffic through or around the construction zone in a way that protects the safety of the traveling public, pedestrians and workers.

The plan must include, but is not limited to, the following items when they are appropriate:

• Sign use and placement;

• Application and removal of pavement markings;

• Construction;

• Scheduling;

• Methods and devices for delineation and channelization;

• Placement and maintenance of devices;

• Placement of flaggers;

• Roadway lighting;

• Traffic regulations;

• Surveillance and inspection.

(8) Advance warning signs.

(a) Employers must provide the following on all flagging operations:

• A three sign advance warning sequence on all roadways with a speed limit below 45 mph.

• A four sign advance warning sequence on all roadways with a 45 mph or higher speed limit.

(b) Warning signs must reflect the actual condition of the work zone. When not in use, warning signs must either be taken down or covered.

(c) Employers must make sure to follow Table 1 for spacing of advance warning sign placement.

If terrain does not allow a motorist to see the flagger from the "flagger ahead" sign, the distance between the flagger and the sign must be shortened to allow visual contact, but in no case can the distance be less than the distance specified in Table 1, Advanced Warning Sign Spacing.

 

(9) Providing a safe job site for flaggers. Employers, responsible contractors and/or project owners must make sure that:

(a) Flagger stations are located far enough in advance of the work space so that the approaching road users will have sufficient distance to stop before entering the work space. Follow Table 2 for the distance of the flagger workstation in advance of the work space.

(b) Flaggers stand either on the shoulder adjacent to the road user being controlled or in the closed lane prior to stopping road users. A flagger must only stand in the lane being used by moving road users after road users have stopped.

Road user means a vehicle operator, bicyclist, or pedestrian within a public roadway, including workers in temporary traffic control zones.

(c) Flagger workstations are illuminated during hours of darkness by floodlights that do not create glare that poses a hazard for drivers.

(d) Flaggers are not assigned other duties while engaged in flagging activities.

(e) Flaggers do not use devices that may distract the flagger's vision, hearing, or attention.

• Examples of these devices include cell phones, pagers, radios, and headphones.

• Devices such as two-way radios used for communications between flaggers to direct traffic or ensure flagger safety are acceptable.

(f) Flaggers receive a rest period of at least ten minutes, on the employer's time, for each four hours of working time.

• Rest periods must be scheduled as near as possible to the midpoint of the work period.

• A flagger must not be allowed to work more than three hours without a rest period.