READ FIRST TIME 02/03/06.   

     AN ACT Relating to regulating the business of installing, repairing, and maintaining domestic water pumping systems; amending RCW 18.106.010, 18.106.040, 18.106.050, 18.106.110, 19.28.041, 19.28.161, 19.28.051, 19.28.061, 18.106.070, 18.106.020, 19.28.211, 19.28.131, and 18.27.060; reenacting and amending RCW 19.28.191; and prescribing penalties.

BE IT ENACTED BY THE LEGISLATURE OF THE STATE OF WASHINGTON:

Sec. 1   RCW 18.106.010 and 2003 c 399 s 102 are each amended to read as follows:
     ((Unless a different meaning is plainly required by the context, the following words and phrases as hereinafter used in this chapter shall have the following meaning:)) The definitions in this section apply throughout this chapter unless the context clearly requires otherwise.
     (1) "Advisory board" means the state advisory board of plumbers((;)).
     (2) "Contractor" means any person, corporate or otherwise, who engages in, or offers or advertises to engage in, any work covered by the provisions of this chapter by way of trade or business, or any person, corporate or otherwise, who employs anyone, or offers or advertises to employ anyone, to engage in any work covered by the provisions of this chapter((;)).
     (3) "Department" means the department of labor and industries((;)).
     (4) "Director" means the director of department of labor and industries((;)).
     (5) "Journeyman plumber" means any person who has been issued a certificate of competency by the department of labor and industries as provided in this chapter((;)).
     (6) "Like-in-kind" means having similar characteristics such as plumbing size, type, and function, and being in the same location((;)).
     (7) "Medical gas piping" means oxygen, nitrous oxide, high pressure nitrogen, medical compressed air, and medical vacuum systems((;)).
     (8) "Medical gas piping installer" means a journeyman plumber who has been issued a medical gas piping installer endorsement((;)).
     (9) "Plumbing" means that craft involved in installing, altering, repairing and renovating potable water systems, liquid waste systems, and medical gas piping systems within a building. Installation in a water system of water softening or water treatment equipment is not within the meaning of plumbing as used in this chapter((;)).
     (10) "Specialty plumber" means anyone who has been issued a specialty certificate of competency limited to:
     (a) Installation, maintenance, and repair of the plumbing of single-family dwellings, duplexes, and apartment buildings that do not exceed three stories; ((or))
     (b) Maintenance and repair of backflow prevention assemblies; or
     (c) A domestic water pumping system consisting of the installation, maintenance, and repair of the pressurization, treatment, and filtration components of a domestic water system consisting of: One or more pumps; pressure, storage, and other tanks; filtration and treatment equipment; if appropriate, a pitless adapter; along with valves, transducers, and other plumbing components that:
     (i) Are used to acquire, treat, store, or move water suitable for either drinking or other domestic purposes, including irrigation, to: (A) A single-family dwelling, duplex, or other similar place of residence; (B) a public water system, as defined in RCW 70.119.020 and as limited under RCW 70.119.040; or (C) a farm owned and operated by a person whose primary residence is located within thirty miles of any part of the farm;
     (ii) Are located within the interior space, including but not limited to an attic, basement, crawl space, or garage, of a residential structure, which space is separated from the living area of the residence by a lockable entrance and fixed walls, ceiling, or floor;
     (iii) If located within the interior space of a residential structure, are connected to a plumbing distribution system supplied and installed into the interior space by either: (A) A person who, pursuant to RCW 18.106.070 or 18.106.090, possesses a valid temporary permit or certificate of competency as a journeyman plumber, specialty plumber, or trainee, as defined in this chapter; or (B) a person exempt from the requirement to obtain a certified plumber to do such plumbing work under RCW 18.106.150.

Sec. 2   RCW 18.106.040 and 2001 c 281 s 2 are each amended to read as follows:
     (1) Upon receipt of the application and evidence set forth in RCW 18.106.030, the director shall review the same and make a determination as to whether the applicant is eligible to take an examination for the certificate of competency. To be eligible to take the examination:
     (a) Each applicant for a journeyman plumber's certificate of competency shall furnish written evidence that he or she has completed a course of study in the plumbing trade in the armed services of the United States or at a school licensed by the work force training and education coordinating board, or has had four or more years of experience under the direct supervision of a licensed journeyman plumber.
     (b) Each applicant for a specialty plumber's certificate of competency under RCW 18.106.010(((8))) (10)(a) shall furnish written evidence that he or she has completed a course of study in the plumbing trade in the armed services of the United States or at a school licensed by the work force training and education coordinating board under chapter 28C.10 RCW, or that he or she has had at least three years practical experience in the specialty.
     (c) Each applicant for a specialty plumber's certificate of competency under RCW 18.106.010(((8)))(10) (b) or (c) shall furnish written evidence that he or she is eligible to take the examination. These eligibility requirements for the specialty plumbers defined by RCW 18.106.010(10)(c) shall be one year of practical experience working on pumping systems not exceeding one hundred gallons per minute, and two years of practical experience working on pumping systems exceeding one hundred gallons per minute, or equivalent as determined by rule by the department in consultation with the advisory board, and that experience may be obtained at the same time the individual is meeting the experience required by RCW 19.28.191. The eligibility requirements for other specialty plumbers shall be ((adopted)) established by rule by the director pursuant to subsection (2)(b) of this section.
     (2)(a) The director shall establish reasonable rules for the examinations to be given applicants for certificates of competency. In establishing the rules, the director shall consult with the state advisory board of plumbers as established in RCW 18.106.110.
     (b) The director shall establish reasonable criteria by rule for determining an applicant's eligibility to take an examination for the certificate of competency for specialty plumbers under subsection (1)(c) of this section. In establishing the criteria, the director shall consult with the state advisory board of plumbers as established in RCW 18.106.110. These rules must take effect by ((July 1, 2002)) December 31, 2006.
     (3) Upon determination that the applicant is eligible to take the examination, the director shall so notify the applicant, indicating the time and place for taking the same.
     (4) No other requirement for eligibility may be imposed.

Sec. 3   RCW 18.106.050 and 1997 c 326 s 5 are each amended to read as follows:
     (1) The department, with the advice of the advisory board, shall prepare a written examination to be administered to applicants for certificates of competency for journeyman plumber and specialty plumber. The examination shall be constructed to determine:
     (a) Whether the applicant possesses varied general knowledge of the technical information and practical procedures that are identified with the trade of journeyman plumber or specialty plumber; and
     (b) Whether the applicant is familiar with the applicable plumbing codes and the administrative rules of the department pertaining to plumbing and plumbers.
     ((The department shall administer the examination to eligible persons. All applicants shall, before taking the examination, pay to the department a fee.))
     (2) ((For purposes of the medical gas piping installer endorsement,)) The department, with the consent of the advisory board, may enter into a contract with a nationally recognized testing agency to develop, administer, and score ((medical gas piping installer)) any examinations required by this chapter. All applicants shall, before taking an examination ((for a medical gas piping installer endorsement)), pay the required examination fee. The department shall set the examination fee by contract with a nationally recognized testing agency. The fee shall cover but not exceed the costs of preparing and administering the examination and the materials necessary to conduct the practical elements of the examination. The department shall approve training courses and set the fees for training courses for ((the medical gas piping installer endorsement)) examinations provided by this chapter.
     (3) An examination to determine the competency of an applicant for a domestic water pumping system specialty plumbing certificate as defined by RCW 18.106.010(10)(c) must be established by the department in consultation with the advisory board by December 31, 2006. The department may include an examination for appropriate electrical safety and technical requirements as required by RCW 19.28.191 with the examination required by this section. The department, in consultation with the advisory board, may accept the certification by a professional or trade association or other acceptable entity as meeting the examination requirement of this section. Individuals who can provide evidence to the department prior to January 1, 2007, that they have been employed in the pump and irrigation business as defined by RCW 18.106.010(10)(c) for not less than four thousand hours in the most recent four calendar years shall be issued the appropriate certificate by the department upon receiving such documentation and applicable fees. The department shall establish a single document for those who have received both the plumbing specialty certification defined by this subsection and have also met the certification requirements for a pump and irrigation or domestic pump specialty electrician, showing that the individual has received both certifications.
     (4) The department shall certify the results of the examinations provided by this chapter, and shall notify the applicant in writing whether he or she has passed or failed. Any applicant who has failed the examination may retake the examination, upon the terms and after a period of time that the director shall set by rule. The director may not limit the number of times that a person may take the examination.

Sec. 4   RCW 18.106.110 and 1997 c 307 s 1 are each amended to read as follows:
     (1) There is created a state advisory board of plumbers, to be composed of ((five)) seven members appointed by the governor. Two members shall be journeyman plumbers, ((two)) one member shall be a specialty plumber, three members shall be persons conducting a plumbing business, at least one of which shall be primarily engaged in a specialty plumbing business, and one member from the general public who is familiar with the business and trade of plumbing.
     (2) The term of one journeyman plumber expires July 1, 1995; the term of the second journeyman plumber expires July 1, 2000; the term of the specialty plumber expires July 1, 2008; the term of one person conducting a plumbing business expires July 1, 1996; the term of the second person conducting a plumbing business expires July 1, 2000; the term of the third person conducting a plumbing business expires July 1, 2007; and the term of the public member expires July 1, 1997. Thereafter, upon the expiration of said terms, the governor shall appoint a new member to serve for a period of three years. However, to ensure that the board can continue to act, a member whose term expires shall continue to serve until his or her replacement is appointed. In the case of any vacancy on the board for any reason, the governor shall appoint a new member to serve out the term of the person whose position has become vacant.
     (3) The advisory board shall carry out all the functions and duties enumerated in this chapter, as well as generally advise the department on all matters relative to this chapter.
     (4) Each member of the advisory board shall receive travel expenses in accordance with the provisions of RCW 43.03.050 and 43.03.060 as now existing or hereafter amended for each day in which such member is actually engaged in attendance upon the meetings of the advisory board.

Sec. 5   RCW 19.28.041 and 2002 c 249 s 2 are each amended to read as follows:
     (1) It is unlawful for any person, firm, partnership, corporation, or other entity to advertise, engage in, conduct, or carry on the business of installing or maintaining wires or equipment to convey electric current, or installing or maintaining equipment to be operated by electric current as it pertains to the electrical industry, without having an unrevoked, unsuspended, and unexpired electrical contractor license, issued by the department in accordance with this chapter. All electrical contractor licenses expire twenty-four calendar months following the day of their issue. The department may issue an electrical contractors license for a period of less than twenty-four months only for the purpose of equalizing the number of electrical contractor licenses that expire each month. Application for an electrical contractor license shall be made in writing to the department, accompanied by the required fee. The application shall state:
     (a) The name and address of the applicant; in case of firms or partnerships, the names of the individuals composing the firm or partnership; in case of corporations, the names of the managing officials thereof;
     (b) The location of the place of business of the applicant and the name under which the business is conducted;
     (c) Employer social security number;
     (d) Evidence of workers' compensation coverage for the applicant's employees working in Washington, as follows:
     (i) The applicant's industrial insurance account number issued by the department;
     (ii) The applicant's self-insurer number issued by the department; or
     (iii) For applicants domiciled in a state or province of Canada subject to an agreement entered into under RCW 51.12.120(7), as permitted by the agreement, filing a certificate of coverage issued by the agency that administers the workers' compensation law in the applicant's state or province of domicile certifying that the applicant has secured the payment of compensation under the other state's or province's workers' compensation law;
     (e) Employment security department number;
     (f) State excise tax registration number;
     (g) Unified business identifier (UBI) account number may be substituted for the information required by (d) of this subsection if the applicant will not employ employees in Washington, and by (e) and (f) of this subsection; and
     (h) Whether a general or specialty electrical contractor license is sought and, if the latter, the type of specialty. Electrical contractor specialties include, but are not limited to: Residential, pump and irrigation, limited energy system, signs, nonresidential maintenance, restricted nonresidential maintenance, appliance repair, and a combination specialty. A general electrical contractor license shall grant to the holder the right to engage in, conduct, or carry on the business of installing or maintaining wires or equipment to carry electric current, and installing or maintaining equipment, or installing or maintaining material to fasten or insulate such wires or equipment to be operated by electric current, in the state of Washington. A specialty electrical contractor license shall grant to the holder a limited right to engage in, conduct, or carry on the business of installing or maintaining wires or equipment to carry electrical current, and installing or maintaining equipment; or installing or maintaining material to fasten or insulate such wires or equipment to be operated by electric current in the state of Washington as expressly allowed by the license.
     (2) The department may verify the workers' compensation coverage information provided by the applicant under subsection (1)(d) of this section, including but not limited to information regarding the coverage of an individual employee of the applicant. If coverage is provided under the laws of another state, the department may notify the other state that the applicant is employing employees in Washington.
     (3) The application for an electrical contractor license shall be accompanied by a bond in the sum of four thousand dollars with the state of Washington named as obligee in the bond, with good and sufficient surety, to be approved by the department. The bond shall at all times be kept in full force and effect, and any cancellation or revocation thereof, or withdrawal of the surety therefrom, suspends the license issued to the principal until a new bond has been filed and approved as provided in this section. Upon approval of a bond, the department shall on the next business day deposit the fee accompanying the application in the electrical license fund and shall file the bond in the office. The department shall upon request furnish to any person, firm, partnership, corporation, or other entity a certified copy of the bond upon the payment of a fee that the department shall set by rule. The fee shall cover but not exceed the cost of furnishing the certified copy. The bond shall be conditioned that in any installation or maintenance of wires or equipment to convey electrical current, and equipment to be operated by electrical current, the principal will comply with the provisions of this chapter and with any electrical ordinance, building code, or regulation of a city or town adopted pursuant to RCW 19.28.010(3) that is in effect at the time of entering into a contract. The bond shall be conditioned further that the principal will pay for all labor, including employee benefits, and material furnished or used upon the work, taxes and contributions to the state of Washington, and all damages that may be sustained by any person, firm, partnership, corporation, or other entity due to a failure of the principal to make the installation or maintenance in accordance with this chapter or any applicable ordinance, building code, or regulation of a city or town adopted pursuant to RCW 19.28.010(3). In lieu of the surety bond required by this section the license applicant may file with the department a cash deposit or other negotiable security acceptable to the department. If the license applicant has filed a cash deposit, the department shall deposit the funds in a special trust savings account in a commercial bank, mutual savings bank, or savings and loan association and shall pay annually to the depositor the interest derived from the account.
     (4) The department shall issue general or specialty electrical contractor licenses to applicants meeting all of the requirements of this chapter. The provisions of this chapter relating to the licensing of any person, firm, partnership, corporation, or other entity including the requirement of a bond with the state of Washington named as obligee therein and the collection of a fee therefor, are exclusive, and no political subdivision of the state of Washington may require or issue any licenses or bonds or charge any fee for the same or a similar purpose. No person, firm, partnership, corporation, or other entity holding more than one specialty contractor license under this chapter may be required to pay an annual fee for more than one such license or to post more than one four thousand dollar bond, equivalent cash deposit, or other negotiable security.
     (5) To obtain a general or specialty electrical contractor license the applicant must designate an individual who currently possesses a valid master journeyman electrician's certificate of competency, master specialty electrician's certificate of competency in the specialty for which application has been made, or administrator's certificate as a general electrical contractor administrator or as a specialty electrical contractor administrator in the specialty for which application has been made.
     (6) Administrator certificate specialties include but are not limited to: Residential, pump and irrigation or domestic pump, limited energy system, signs, nonresidential maintenance, restricted nonresidential maintenance, appliance repair, and combination specialty. To obtain an administrator's certificate an individual must pass an examination as set forth in RCW 19.28.051 unless the applicant was a licensed electrical contractor at any time during 1974. Applicants who were electrical contractors licensed by the state of Washington at any time during 1974 are entitled to receive a general electrical contractor administrator's certificate without examination if the applicants apply prior to January 1, 1984. The board of electrical examiners shall certify to the department the names of all persons who are entitled to either a general or specialty electrical contractor administrator's certificate.
     (7) For a contractor doing domestic water pumping system work as defined by RCW 18.106.010(10)(c), the department shall consider the requirements of subsections (1)(a) through (h), (2), and (3) of this section to have been met to be a pump and irrigation or domestic pump licensed electrical contractor if the contractor has met the contractor registration requirements of chapter 18.27 RCW. The department shall establish a single registration/licensing document for those who qualify for both general contractor registration as defined in chapter 18.27 RCW and a pump and irrigation or domestic pump electrical contractor license as defined by this chapter.

Sec. 6   RCW 19.28.161 and 2002 c 249 s 4 are each amended to read as follows:
     (1) No person may engage in the electrical construction trade without having a valid master journeyman electrician certificate of competency, journeyman electrician certificate of competency, master specialty electrician certificate of competency, or specialty electrician certificate of competency issued by the department in accordance with this chapter. Electrician certificate of competency specialties include, but are not limited to: Residential, pump and irrigation, limited energy system, signs, nonresidential maintenance, restricted nonresidential maintenance, and appliance repair. Until July 1, 2007, the department of labor and industries shall issue a written warning to any specialty pump and irrigation or domestic pump electrician not having a valid electrician certification. The warning will state that the individual must apply for an electrical training certificate or be qualified for and apply for electrician certification under the requirements in RCW 19.28.191(1)(g) within thirty calendar days of the warning. Only one warning will be issued to any individual. If the individual fails to comply with this section, the department shall issue a penalty as defined in RCW 19.28.271 to the individual.
     (2) A person who is indentured in an apprenticeship program approved under chapter 49.04 RCW for the electrical construction trade or who is learning the electrical construction trade may work in the electrical construction trade if supervised by a certified master journeyman electrician, journeyman electrician, master specialty electrician in that electrician's specialty, or specialty electrician in that electrician's specialty. All apprentices and individuals learning the electrical construction trade shall obtain an electrical training certificate from the department. The certificate shall authorize the holder to learn the electrical construction trade while under the direct supervision of a master journeyman electrician, journeyman electrician, master specialty electrician working in that electrician's specialty, or specialty electrician working in that electrician's specialty. The holder of the electrical training certificate shall renew the certificate biennially. At the time of renewal, the holder shall provide the department with an accurate list of the holder's employers in the electrical construction industry for the previous biennial period and the number of hours worked for each employer. A biennial fee shall be charged for the issuance or renewal of the certificate. The department shall set the fee by rule. The fee shall cover but not exceed the cost of administering and enforcing the trainee certification and supervision requirements of this chapter. Apprentices and individuals learning the electrical construction trade shall have their electrical training certificates in their possession at all times that they are performing electrical work. They shall show their certificates to an authorized representative of the department at the representative's request.
     (3) Any person who has been issued an electrical training certificate under this chapter may work if that person is under supervision. Supervision shall consist of a person being on the same job site and under the control of either a certified master journeyman electrician, journeyman electrician, master specialty electrician working in that electrician's specialty, or specialty electrician working in that electrician's specialty. Either a certified master journeyman electrician, journeyman electrician, master specialty electrician working in that electrician's specialty, or specialty electrician working in that electrician's specialty shall be on the same job site as the noncertified individual for a minimum of seventy-five percent of each working day unless otherwise provided in this chapter.
     (4) The ratio of noncertified individuals to certified master journeymen electricians, journeymen electricians, master specialty electricians, or specialty electricians on any one job site is as follows:
     (a) When working as a specialty electrician, not more than two noncertified individuals for every certified master specialty electrician working in that electrician's specialty, specialty electrician working in that electrician's specialty, master journeyman electrician, or journeyman electrician, except that the ratio requirements are one certified master specialty electrician working in that electrician's specialty, specialty electrician working in that electrician's specialty, master journeyman electrician, or journeyman electrician working as a specialty electrician to no more than four students enrolled in and working as part of an electrical construction program at public community or technical colleges, or not-for-profit nationally accredited trade or technical schools licensed by the work force training and education coordinating board under chapter 28C.10 RCW. In meeting the ratio requirements for students enrolled in an electrical construction program at a trade school, a trade school may receive input and advice from the electrical board; and
     (b) When working as a journeyman electrician, not more than one noncertified individual for every certified master journeyman electrician or journeyman electrician, except that the ratio requirements shall be one certified master journeyman electrician or journeyman electrician to no more than four students enrolled in and working as part of an electrical construction program at public community or technical colleges, or not-for-profit nationally accredited trade or technical schools licensed by the work force training and education coordinating board under chapter 28C.10 RCW. In meeting the ratio requirements for students enrolled in an electrical construction program at a trade school, a trade school may receive input and advice from the electrical board.
     An individual who has a current training certificate and who has successfully completed or is currently enrolled in an approved apprenticeship program or in an electrical construction program at public community or technical colleges, or not-for-profit nationally accredited technical or trade schools licensed by the work force training and education coordinating board under chapter 28C.10 RCW, may work without direct on-site supervision during the last six months of meeting the practical experience requirements of this chapter.
     (5) For the residential (as specified in WAC ((296-46A-930)) 296-46B-920(2)(a)), pump and irrigation (as specified in WAC ((296-46A-930(2)(b)(i))) 296-46B-920(2)(b)), sign (as specified in WAC ((296-46A-930(2)(c))) 296-46B-920(2)(d)), limited energy (as specified in WAC ((296-46A-930(2)(e)(i))) 296-46B-920(2)(e)), nonresidential maintenance (as specified in WAC ((296-46A-930(2)(f)(i))) 296-46B-920(2)(g)), restricted nonresidential maintenance as determined by the department in rule, or other new nonresidential specialties, not including appliance repair, as determined by the department in rule, either a master journeyman electrician, journeyman electrician, master specialty electrician working in that electrician's specialty, or specialty electrician working in that electrician's specialty must be on the same job site as the noncertified individual for a minimum of seventy-five percent of each working day. Other specialties must meet the requirements specified in RCW 19.28.191(((1)(f)(ii))) (1)(g)(ii). When the ratio of certified electricians to noncertified individuals on a job site is one certified electrician to three or four noncertified individuals, the certified electrician must:
     (a) Directly supervise and instruct the noncertified individuals and the certified electrician may not directly make or engage in an electrical installation; and
     (b) Be on the same job site as the noncertified individual for a minimum of one hundred percent of each working day.
     (6) The electrical contractor shall accurately verify and attest to the electrical trainee hours worked by electrical trainees on behalf of the electrical contractor.

Sec. 7   RCW 19.28.191 and 2003 c 399 s 601 and 2003 c 211 s 1 are each reenacted and amended to read as follows:
     (1) Upon receipt of the application, the department shall review the application and determine whether the applicant is eligible to take an examination for the master journeyman electrician, journeyman electrician, master specialty electrician, or specialty electrician certificate of competency.
     (a) Before July 1, 2005, an applicant who possesses a valid journeyman electrician certificate of competency in effect for the previous four years and a valid general administrator's certificate may apply for a master journeyman electrician certificate of competency without examination.
     (b) Before July 1, 2005, an applicant who possesses a valid specialty electrician certificate of competency, in the specialty applied for, for the previous two years and a valid specialty administrator's certificate, in the specialty applied for, may apply for a master specialty electrician certificate of competency without examination.
     (c) Before December 1, 2003, the following persons may obtain an equipment repair specialty electrician certificate of competency without examination:
     (i) A person who has successfully completed an apprenticeship program approved under chapter 49.04 RCW for the machinist trade; and
     (ii) A person who provides evidence in a form prescribed by the department affirming that: (A) He or she was employed as of April 1, 2003, by a factory-authorized equipment dealer or service company; and (B) he or she has worked in equipment repair for a minimum of four thousand hours.
     (d) To be eligible to take the examination for a master journeyman electrician certificate of competency the applicant must have possessed a valid journeyman electrician certificate of competency for four years.
     (e) To be eligible to take the examination for a master specialty electrician certificate of competency the applicant must have possessed a valid specialty electrician certificate of competency, in the specialty applied for, for two years.
     (f) To be eligible to take the examination for a journeyman certificate of competency the applicant must have:
     (i) Worked in the electrical construction trade for a minimum of eight thousand hours, of which four thousand hours shall be in industrial or commercial electrical installation under the supervision of a master journeyman electrician or journeyman electrician and not more than a total of four thousand hours in all specialties under the supervision of a master journeyman electrician, journeyman electrician, master specialty electrician working in that electrician's specialty, or specialty electrician working in that electrician's specialty. Speciality electricians with less than a four thousand hour work experience requirement cannot credit the time required to obtain that specialty towards qualifying to become a journeyman electrician; or
     (ii) Successfully completed an apprenticeship program approved under chapter 49.04 RCW for the electrical construction trade.
     (g) To be eligible to take the examination for a specialty electrician certificate of competency the applicant must have:
     (i) Worked in the residential (as specified in WAC ((296-46A-930)) 296-46B-920(2)(a)), pump and irrigation (as specified in WAC ((296-46A-930(2)(b)(i))) 296-46B-920(2)(b)), sign (as specified in WAC ((296-46A-930(2)(c))) 296-46B-920(2)(d)), limited energy (as specified in WAC ((296-46A-930(2)(e)(i))) 296-46B-920(2)(e)), nonresidential maintenance (as specified in WAC ((296-46A-930(2)(f)(i))) 296-46B-920(2)(g)), or other new nonresidential specialties as determined by the department in rule under the supervision of a master journeyman electrician, journeyman electrician, master specialty electrician working in that electrician's specialty, or specialty electrician working in that electrician's specialty for a minimum of four thousand hours; ((or))
     (ii) Worked in the appliance repair specialty as determined by the department in rule, restricted nonresidential maintenance as determined by the department in rule, the equipment repair specialty as determined by the department in rule, the pump and irrigation specialty other than as defined by (g)(i) of this subsection or domestic pump specialty as determined by the department in rule, or a specialty other than the designated specialties in (g)(i) of this subsection for a minimum of the initial ninety days, or longer if set by rule by the department. The restricted nonresidential maintenance specialty is limited to a maximum of 277 volts and 20 amperes for lighting branch circuits and/or a maximum of 250 volts and 60 amperes for other circuits, but excludes the replacement or repair of circuit breakers. The initial period must be spent under one hundred percent supervision of a master journeyman electrician, journeyman electrician, master specialty electrician working in that electrician's specialty, or specialty electrician working in that electrician's specialty. After this initial period, a person may take the specialty examination. If the person passes the examination, the person may work unsupervised for the balance of the minimum hours required for certification. A person may not be certified as a specialty electrician in the appliance repair specialty or in a specialty other than the designated specialities in (g)(i) of this subsection, however, until the person has worked a minimum of two thousand hours in that specialty, or longer if set by rule by the department; ((or))
     (iii) Successfully completed an approved apprenticeship program under chapter 49.04 RCW for the applicant's specialty in the electrical construction trade; or
     (iv) In meeting the training requirements for the pump and irrigation or domestic pump specialties, the individual shall be allowed to obtain the experience required by this section at the same time the individual is meeting the experience required by RCW 18.106.040(1)(c). After meeting the training requirements provided in this section, the individual may take the examination and upon passing the examination, meeting additional training requirements as may still be required for those seeking a pump and irrigation, or a domestic pump specialty certificate as defined by rule, and paying the applicable fees, the individual must be issued the appropriate certificate. The department may include an examination for specialty plumbing certificate defined in RCW 18.106.010(10)(c) with the examination required by this section. The department, by rule and in consultation with the electrical board, may establish additional equivalent ways to gain the experience requirements required by this subsection. Individuals who are able to provide evidence to the department, prior to January 1, 2007, that they have been employed as a pump installer in the pump and irrigation or domestic pump business by an appropriately licensed electrical contractor, registered general contractor defined by chapter 18.27 RCW, or appropriate general specialty contractor defined by chapter 18.27 RCW for not less than eight thousand hours in the most recent six calendar years shall be issued the appropriate certificate by the department upon receiving such documentation and applicable fees. The department shall establish a single document for those who have received both an electrical specialty certification as defined by this subsection and have also met the certification requirements for the specialty plumber as defined by RCW 18.106.010(10)(c), showing that the individual has received both certifications. No other experience or training requirements may be imposed.
     (h) Any applicant for a journeyman electrician certificate of competency who has successfully completed a two-year program in the electrical construction trade at public community or technical colleges, or not-for-profit nationally accredited technical or trade schools licensed by the work force training and education coordinating board under chapter 28C.10 RCW may substitute up to two years of the technical or trade school program for two years of work experience under a master journeyman electrician or journeyman electrician. The applicant shall obtain the additional two years of work experience required in industrial or commercial electrical installation prior to the beginning, or after the completion, of the technical school program. Any applicant who has received training in the electrical construction trade in the armed service of the United States may be eligible to apply armed service work experience towards qualification to take the examination for the journeyman electrician certificate of competency.
     (i) An applicant for a specialty electrician certificate of competency who, after January 1, 2000, has successfully completed a two-year program in the electrical construction trade at a public community or technical college, or a not-for-profit nationally accredited technical or trade school licensed by the work force training and education coordinating board under chapter 28C.10 RCW, may substitute up to one year of the technical or trade school program for one year of work experience under a master journeyman electrician, journeyman electrician, master specialty electrician working in that electrician's specialty, or specialty electrician working in that electrician's specialty. Any applicant who has received training in the electrical construction trade in the armed services of the United States may be eligible to apply armed service work experience towards qualification to take the examination for an appropriate specialty electrician certificate of competency.
     (j) The department must determine whether hours of training and experience in the armed services or school program are in the electrical construction trade and appropriate as a substitute for hours of work experience. The department must use the following criteria for evaluating the equivalence of classroom electrical training programs and work in the electrical construction trade:
     (i) A two-year electrical training program must consist of three thousand or more hours.
     (ii) In a two-year electrical training program, a minimum of two thousand four hundred hours of student/instructor contact time must be technical electrical instruction directly related to the scope of work of the electrical specialty. Student/instructor contact time includes lecture and in-school lab.
     (iii) The department may not allow credit for a program that accepts more than one thousand hours transferred from another school's program.
     (iv) Electrical specialty training school programs of less than two years will have all of the above student/instructor contact time hours proportionately reduced. Such programs may not apply to more than fifty percent of the work experience required to attain certification.
     (v) Electrical training programs of less than two years may not be credited towards qualification for journeyman electrician unless the training program is used to gain qualification for a four thousand hour electrical specialty.
     (k) No other requirement for eligibility may be imposed.
     (2) The department shall establish reasonable rules for the examinations to be given applicants for certificates of competency. In establishing the rules, the department shall consult with the board. Upon determination that the applicant is eligible to take the examination, the department shall so notify the applicant, indicating the time and place for taking the examination.
     (3) No noncertified individual may work unsupervised more than one year beyond the date when the trainee would be eligible to test for a certificate of competency if working on a full-time basis after original application for the trainee certificate. For the purposes of this section, full-time basis means two thousand hours.

Sec. 8   RCW 19.28.051 and 2001 c 211 s 4 are each amended to read as follows:
     It shall be the purpose and function of the board to establish, in addition to a general electrical contractors' license, such classifications of specialty electrical contractors' licenses as it deems appropriate with regard to individual sections pertaining to state adopted codes in this chapter. In addition, it shall be the purpose and function of the board to establish and administer written examinations for general electrical administrators' certificates and the various specialty electrical administrators' certificates. Examinations shall be designed to reasonably ((insure)) ensure that general and specialty electrical administrators' certificate holders are competent to engage in and supervise the work covered by this statute and their respective licenses. The examinations shall include questions from the following categories to ((assure)) ensure proper safety and protection for the general public: (1) Safety, (2) state electrical code, and (3) electrical theory. The department with the consent of the board shall be permitted to enter into a contract with a professional testing agency to develop, administer, and score these examinations, or accept certifications or other appropriate demonstrations established by independent entities that otherwise fulfill the examination requirements of this section. Individuals who can provide evidence to the department, prior to January 1, 2007, that they have been employed as a pump installer in the pump and irrigation or domestic pump business by an appropriately licensed electrical contractor, registered general contractor defined by chapter 18.27 RCW, or appropriate general specialty contractor defined by chapter 18.27 RCW for not less than eight thousand hours in the most recent six calendar years shall be issued the appropriate administrator's certificate by the department upon receiving such documentation and applicable fees. The fee for the examination may be set by the department in its contract with the professional testing agency. The department may direct that the applicant pay the fee to the professional testing agency. The fee shall cover but not exceed the costs of preparing and administering the examination. It shall be the further purpose and function of this board to advise the director as to the need of additional electrical inspectors and compliance officers to be utilized by the director on either a full-time or part-time employment basis and to carry out the duties enumerated in RCW 19.28.161 through 19.28.271 as well as generally advise the department on all matters relative to RCW 19.28.161 through 19.28.271.

Sec. 9   RCW 19.28.061 and 2002 c 249 s 3 are each amended to read as follows:
     (1) Each applicant for an electrical contractor's license, other than an individual, shall designate a supervisory employee or member of the firm to take the required master electrician's or administrator's examination. Effective July 1, 1987, a supervisory employee designated as the electrical contractor's master electrician or administrator shall be a full-time supervisory employee. This person shall be designated as master electrician or administrator under the license. No person may concurrently qualify as master electrician or administrator for more than one contractor. If the relationship of the master electrician or administrator with the electrical contractor is terminated, the contractor's license is void within ninety days unless another master electrician or administrator is qualified by the board. However, if the master electrician or administrator dies or is otherwise incapacitated, the contractor's license is void within one hundred eighty days unless another master electrician or administrator is qualified by the board. The contractor must notify the department in writing within ten days if the master electrician's or administrator's relationship with the contractor terminates due to the master electrician's or administrator's death or incapacitation.
     (2) The department must issue an administrator's certificate to all applicants who have passed the examination as provided in RCW 19.28.051 and this section, and who have complied with the rules adopted under this chapter. The administrator's certificate must bear the date of issuance, expires on the holder's birthday, and is nontransferable. The certificate must be renewed every three years, upon application, on or before the holder's birthday.
     (a) If the certificate holder demonstrates to the department that he or she has satisfactorily completed an annual eight-hour continuing education course, the certificate may be renewed by appropriate application without examination unless the certificate has been revoked, suspended, or not renewed within ninety days after the expiration date. For holders of pump and irrigation or domestic pump specialty administrator certificates, the continuing education may comprise both electrical and plumbing education.
     (b) The contents and requirements for satisfactory completion of the continuing education course must be determined by the director and approved by the board.
     (c) The department must accept proof of a certificate holder's satisfactory completion of a continuing education course offered in another state as meeting the requirements for maintaining a current Washington state certificate if the department is satisfied the course is comparable in nature to that required in Washington state for maintaining a current certificate.
     (3) A fee must be assessed for each administrator's certificate and for each renewal. An individual holding more than one administrator's certificate under this chapter is not required to pay fees for more than one certificate. The department must set the fees by rule for issuance and renewal of a certificate. The fees must cover, but not exceed, the costs of issuing the certificates and of administering and enforcing the administrator certification requirements of this chapter.
     (4) The department may deny an application for an administrator's certificate for up to two years if the applicant's previous administrator's certificate has been revoked for a serious violation and all appeals concerning the revocation have been exhausted. For the purposes of this section only, a serious violation is a violation that presents imminent danger to the public. The certificate may be renewed for a three-year period without examination by appropriate application unless the certificate has been revoked, suspended, or not renewed within ninety days after the expiration date. If the certificate is not renewed before the expiration date, the individual shall pay twice the usual fee. A person may take the administrator's examination as many times as necessary to pass without limit.
     (5) The designated master electrician or administrator shall:
     (a) Be a member of the firm or a supervisory employee and shall be available during working hours to carry out the duties of an administrator under this section;
     (b) Ensure that all electrical work complies with the electrical installation laws and rules of the state;
     (c) Ensure that the proper electrical safety procedures are used;
     (d) Ensure that all electrical labels, permits, and licenses required to perform electrical work are used;
     (e) See that corrective notices issued by an inspecting authority are complied with; and
     (f) Notify the department in writing within ten days if the master electrician or administrator terminates the relationship with the electrical contractor.
     (6) The department shall not by rule change the administrator's duties under subsection (5) of this section.

Sec. 10   RCW 18.106.070 and 2003 c 399 s 801 are each amended to read as follows:
     (1) The department shall issue a certificate of competency to all applicants who have passed the examination and have paid the fee for the certificate. The certificate shall bear the date of issuance, and shall expire on the birthdate of the holder immediately following the date of issuance. The certificate shall be renewable every other year, upon application, on or before the birthdate of the holder, except for specialty plumbers defined by RCW 18.106.010(10)(c) who also have an electrical certification issued jointly as provided by RCW 18.106.050(3) in which case their certificate shall be renewable every three years on or before the birthdate of the holder. The department shall renew a certificate of competency if the applicant: (a) Pays the renewal fee assessed by the department; and (b) during the past two years has completed sixteen hours of continuing education approved by the department with the advice of the advisory board, including four hours related to electrical safety. For holders of the specialty plumber certificate under RCW 18.106.010(10)(c), the continuing education may comprise both electrical and plumbing education with a minimum of twelve of the required twenty-four hours of continuing education in plumbing. If a person fails to renew the certificate by the renewal date, he or she must pay a doubled fee. If the person does not renew the certificate within ninety days of the renewal date, he or she must retake the examination and pay the examination fee.
     The journeyman plumber and specialty plumber certificates of competency, the medical gas piping installer endorsement, and the temporary permit provided for in this chapter grant the holder the right to engage in the work of plumbing as a journeyman plumber, specialty plumber, or medical gas piping installer, in accordance with their provisions throughout the state and within any of its political subdivisions on any job or any employment without additional proof of competency or any other license or permit or fee to engage in the work. This section does not preclude employees from adhering to a union security clause in any employment where such a requirement exists.
     (2) A person who is indentured in an apprenticeship program approved under chapter 49.04 RCW for the plumbing construction trade or who is learning the plumbing construction trade may work in the plumbing construction trade if supervised by a certified journeyman plumber or a certified specialty plumber in that plumber's specialty. All apprentices and individuals learning the plumbing construction trade shall obtain a plumbing training certificate from the department. The certificate shall authorize the holder to learn the plumbing construction trade while under the direct supervision of a journeyman plumber or a specialty plumber working in his or her specialty. The holder of the plumbing training certificate shall renew the certificate annually. At the time of renewal, the holder shall provide the department with an accurate list of the holder's employers in the plumbing construction industry for the previous year and the number of hours worked for each employer. An annual fee shall be charged for the issuance or renewal of the certificate. The department shall set the fee by rule. The fee shall cover but not exceed the cost of administering and enforcing the trainee certification and supervision requirements of this chapter. Apprentices and individuals learning the plumbing construction trade shall have their plumbing training certificates in their possession at all times that they are performing plumbing work. They shall show their certificates to an authorized representative of the department at the representative's request.
     (3) Any person who has been issued a plumbing training certificate under this chapter may work if that person is under supervision. Supervision shall consist of a person being on the same job site and under the control of either a journeyman plumber or an appropriate specialty plumber who has an applicable certificate of competency issued under this chapter. Either a journeyman plumber or an appropriate specialty plumber shall be on the same job site as the noncertified individual for a minimum of seventy-five percent of each working day unless otherwise provided in this chapter. The ratio of noncertified individuals to certified journeymen or specialty plumbers working on a job site shall be: (a) Not more than two noncertified plumbers working on any one job site for every certified specialty plumber or journeyman plumber working as a specialty plumber; and (b) not more than one noncertified plumber working on any one job site for every certified journeyman plumber working as a journeyman plumber.
     An individual who has a current training certificate and who has successfully completed or is currently enrolled in an approved apprenticeship program or in a technical school program in the plumbing construction trade in a school approved by the work force training and education coordinating board, may work without direct on-site supervision during the last six months of meeting the practical experience requirements of this chapter.
     (4) An individual who has a current training certificate and who has successfully completed or is currently enrolled in a medical gas piping installer training course approved by the department may work on medical gas piping systems if the individual is under the direct supervision of a certified medical gas piping installer who holds a medical gas piping installer endorsement one hundred percent of a working day on a one-to-one ratio.
     (5) The training to become a certified plumber must include not less than sixteen hours of classroom training established by the director with the advice of the advisory board. The classroom training must include, but not be limited to, electrical wiring safety, grounding, bonding, and other related items plumbers need to know to work under RCW 19.28.091.
     (6) All persons who are certified plumbers before January 1, 2003, are deemed to have received the classroom training required in subsection (5) of this section.

Sec. 11   RCW 18.106.020 and 2002 c 82 s 2 are each amended to read as follows:
     (1) No person may engage in or offer to engage in the trade of plumbing without having a journeyman certificate, specialty certificate, temporary permit, or trainee certificate. A trainee must be supervised by a person who has a journeyman certificate, specialty certificate, or temporary permit, as specified in RCW 18.106.070. No contractor may employ a person to engage in or offer to engage in the trade of plumbing unless the person employed has a journeyman certificate, specialty certificate, temporary permit, or trainee certificate. This section does not apply to a contractor who is contracting for work on his or her own residence. Until July 1, 2007, the department shall issue a written warning to any specialty plumber defined by RCW 18.106.010(10)(c) not having a valid plumber certification. The warning will state that the individual must apply for a plumber training certificate or be qualified for and apply for plumber certification under the requirements in RCW 18.106.040 within thirty calendar days of the warning. Only one warning will be issued to any individual. If the individual fails to comply with this section, the department shall issue a penalty or penalties as authorized by this chapter.
     (2) No person may engage in or offer to engage in medical gas piping installation without having a certificate of competency as a journeyman plumber and a medical gas piping installer endorsement. A trainee may engage in medical gas piping installation if he or she has a training certificate and is supervised by a person with a medical gas piping installer endorsement. No contractor may employ a person to engage in or offer to engage in medical gas piping installation unless the person employed has a certificate of competency as a journeyman plumber and a medical gas piping installer endorsement.
     (3) No contractor may advertise, offer to do work, submit a bid, or perform any work under this chapter without being registered as a contractor under chapter 18.27 RCW.
     (4) Violation of this section is an infraction. Each day in which a person engages in the trade of plumbing in violation of this section or employs a person in violation of this section is a separate infraction. Each worksite at which a person engages in the trade of plumbing in violation of this section or at which a person is employed in violation of this section is a separate infraction.
     (5) Notices of infractions for violations of this section may be issued to:
     (a) The person engaging in or offering to engage in the trade of plumbing in violation of this section;
     (b) The contractor in violation of this section; and
     (c) The contractor's employee who authorized the work assignment of the person employed in violation of this section.

Sec. 12   RCW 19.28.211 and 2002 c 249 s 7 are each amended to read as follows:
     (1) The department shall issue a certificate of competency to all applicants who have passed the examination provided in RCW 19.28.201, and who have complied with RCW 19.28.161 through 19.28.271 and the rules adopted under this chapter. The certificate shall bear the date of issuance, and shall expire on the holder's birthday. The certificate shall be renewed every three years, upon application, on or before the holder's birthdate. A fee shall be assessed for each certificate and for each annual renewal.
     (2) If the certificate holder demonstrates to the department that he or she has satisfactorily completed an annual eight-hour continuing education course, the certificate may be renewed without examination by appropriate application unless the certificate has been revoked, suspended, or not renewed within ninety days after the expiration date. For pump and irrigation or domestic pump specialty electricians, the continuing education course may combine both electrical and plumbing education provided that there is a minimum of four hours of electrical training in the course.
     (a) The contents and requirements for satisfactory completion of the continuing education course shall be determined by the director and approved by the board.
     (b) The department shall accept proof of a certificate holder's satisfactory completion of a continuing education course offered in another state as meeting the requirements for maintaining a current Washington state certificate of competency if the department is satisfied the course is comparable in nature to that required in Washington state for maintaining a current certificate of competency.
     (3) If the certificate is not renewed before the expiration date, the individual shall pay twice the usual fee. The department shall set the fees by rule for issuance and renewal of a certificate of competency. The fees shall cover but not exceed the costs of issuing the certificates and of administering and enforcing the electrician certification requirements of this chapter.
     (4) The certificates of competency and temporary permits provided for in this chapter grant the holder the right to work in the electrical construction trade as a master electrician, journeyman electrician, or specialty electrician in accordance with their provisions throughout the state and within any of its political subdivisions without additional proof of competency or any other license, permit, or fee to engage in such work.

Sec. 13   RCW 19.28.131 and 2001 c 211 s 8 are each amended to read as follows:
     Until July 1, 2007, the department shall issue a written warning to any specialty contractor, performing the scope of work defined by rule for the pump and irrigation or domestic pump specialties, not having a valid electrical contractor license. The warning will state that the contractor must be qualified for and apply for a specialty electrical contractor license under the requirements in RCW 19.28.041 within thirty calendar days of the warning. Only one warning will be issued to any contractor. If the contractor fails to comply with this section, the department shall issue a penalty or penalties as authorized in this section to the contractor. Any person, firm, partnership, corporation, or other entity violating any of the provisions of RCW 19.28.010 through 19.28.141 and 19.28.311 through 19.28.361 shall be assessed a penalty of not less than fifty dollars or more than ten thousand dollars. The department shall set by rule a schedule of penalties for violating RCW 19.28.010 through 19.28.141 and 19.28.311 through 19.28.361. The department shall notify the person, firm, partnership, corporation, or other entity violating any of the provisions of RCW 19.28.010 through 19.28.141 and 19.28.311 through 19.28.361 of the amount of the penalty and of the specific violation by certified mail, return receipt requested, sent to the last known address of the assessed party. Any penalty is subject to review by an appeal to the board. The filing of an appeal stays the effect of the penalty until the board makes its decision. The appeal shall be filed within twenty days after notice of the penalty is given to the assessed party by certified mail, return receipt requested, sent to the last known address of the assessed party and shall be made by filing a written notice of appeal with the department. The notice shall be accompanied by a certified check for two hundred dollars, which shall be returned to the assessed party if the decision of the department is not sustained by the board. If the board sustains the decision of the department, the two hundred dollars shall be applied by the department to the payment of the per diem and expenses of the members of the board incurred in the matter, and any balance remaining after payment of per diem and expenses shall be paid into the electrical license fund. The hearing and review procedures shall be conducted in accordance with chapter 34.05 RCW. The board shall assign its hearings to an administrative law judge to conduct the hearing and issue a proposed decision and order. The board shall be allowed a minimum of twenty days to review a proposed decision and shall issue its decision no later than the next regularly scheduled board meeting.

Sec. 14   RCW 18.27.060 and 2001 c 159 s 5 are each amended to read as follows:
     (1) A certificate of registration shall be valid for two years and shall be renewed on or before the expiration date. The department shall issue to the applicant a certificate of registration upon compliance with the registration requirements of this chapter.
     (2) If the department approves an application, it shall issue a certificate of registration to the applicant.
     (3) If a contractor's surety bond or other security has an unsatisfied judgment against it or is canceled, or if the contractor's insurance policy is canceled, the contractor's registration shall be automatically suspended on the effective date of the impairment or cancellation. The department shall mail notice of the suspension to the contractor's address on the certificate of registration by certified and by first class mail within two days after suspension.
     (4) Renewal of registration is valid on the date the department receives the required fee and proof of bond and liability insurance, if sent by certified mail or other means requiring proof of delivery. The receipt or proof of delivery shall serve as the contractor's proof of renewed registration until he or she receives verification from the department.
     (5) The department shall immediately suspend the certificate of registration of a contractor who has been certified by the department of social and health services as a person who is not in compliance with a support order or a ((residential or)) visitation order as provided in RCW 74.20A.320. The certificate of registration shall not be reissued or renewed unless the person provides to the department a release from the department of social and health services stating that he or she is in compliance with the order and the person has continued to meet all other requirements for certification during the suspension.
     (6) For a contractor who employs plumbers, as described in RCW 18.106.010(10)(c), and is also required to be licensed as an electrical contractor as required in RCW 19.28.041, while doing pump and irrigation or domestic pump work described in rule as authorized by RCW 19.28.251, the department shall establish a single registration/licensing document for those who qualify for both general contractor registration as defined by this chapter and an electrical contractor license as defined by chapter 19.28 RCW.