PERMANENT RULES
CLEAN AIR AUTHORITY
Date of Adoption: March 8, 2000.
Purpose: To enable the authority to assist the citizens, jurisdictions, and businesses of Yakima County to restore and maintain air quality which conforms to applicable air quality standards with minimal community disruption.
Citation of Existing Rules Affected by this Order: Repealing Restated Regulation I of the Yakima County Clean Air Authority.
Statutory Authority for Adoption: Chapter 70.94 RCW.
Adopted under notice filed as WSR 00-02-034 on December 29, 1999.
Changes Other than Editing from Proposed to Adopted Version: The enclosed public comment, staff response and changes, and the staff comments responses and changes documents show all the changes made in the text from the text printed in the February 16, 2000 WSR. These changes are all considered nonsubstantive by the authority, board, and legal counsel.
PUBLIC COMMENTS, STAFF RESPONSES, AND CHANGES TO DRAFT REGULATION 1 OF THE YRCAA
Received through the Local Adoption Hearing on March 8, 2000
Editorial Changes and Staff Comments and Changes other Documents
Section / Sub. No. & Page No. |
Person Making the Comment |
No. | Comment / Concern | Staff Response | Changes in the Regulation Text | |
Name / Organization |
Date | |||||
General Comments | ||||||
---- | Raymond L. Paolella, City of Yakima | 03/03/00 Letter | 0006 | Multiple versions of Regulation 1 have been circulated. | See 03/08/00 Exec. Memo., ¶ 1. | No changes made in the regulation. |
---- | Raymond L. Paolella, City of Yakima | 03/03/00 Letter | 0007 | State Register notice contains errors or is lacking in detail. | See 03/08/00 Exec. Memo., ¶ 2. | No changes made in the regulation. |
---- | Raymond L. Paolella, City of Yakima | 03/03/00 Letter | 0008 | Contradictions in stated purpose of the regulation and statements by the APCO. | See 03/08/00 Exec. Memo., ¶ 3. | No changes made in the regulation. |
---- | Raymond L. Paolella, City of Yakima | 03/03/00 Letter | 0009 | Requests cancellation of the public hearing and refiling the regulation. | See 03/08/00 Exec. Memo., ¶ 4. | No changes made in the regulation. |
---- | Mary Place, Board Member | 03/08/00 Oral |
0011 | Concerned about the meaning of the cross references to the 1995 Regulation at the start of various sections or subsections. | Explained that these where included to assist reviewers and they will be deleted in the clean text format after adoption. | No changes made in the legislative text format version. |
---- | Judith Boekholder, Council Member, City of Toppenish | 03/08/00, Oral | 0024 | I represent the Yakima Valley Mayor's Assoc. I concur with the City of Yakima comments, and I am pleased to see how those have been resolved. | See comments 0012 through 0023. | No changes made in the regulation. |
3.03, 3.08, 3.01C1d, & 3.01C3 | Judith Boekholder, Council Member, City of Toppenish | 03/08/00, Oral | 0027 | I notice that there were some editorial changes in outdoor burning, dust control, and odor subsections. I hope they have been cleared with the effected organizations. | We worked through all the differences with the Fire Chiefs Assoc.. We did what we could legally do to oblige the dairy industry, but we were not able to all that they requested. We have done extensive work on dust issues in the past with the CWHBA, the construction industry, and the ag industry. | No changes made in the regulation. |
---- | Judith Boekholder, Council Member, City of Toppenish | 03/08/00, Oral | 0029 | Concerned about the March 8, 2000 version of regulation and the limited circulation it was given. Also, which version is being adopted? | Prior to the public hearing, it was explained that the March 8, 2000 version was prepared to show the Board and a few other people the nonsubstantive editorial and clarity text changes being proposed to the Board by the Authority and the public if they adopt the Jan. 5, 2000 version and approved the changes. | No change made or required in the regulation by this comment. |
---- | Steve George, Hop Growers of WA | 03/08/00, Oral | 0030 | The public comments and the staff responses made at the adoption hearing today need to be incorporated into the record. | This is the reason that the hearing is being recorded. The tapes will be transcribed and the public comments and staff responses entered into public comment response file. | No change made or required in the regulation by this comment. |
Article 1 | ||||||
1.03A11, 1 - 1 | Mary Place, Board Member | 03/08/00 Oral | 0010 | The name Yakama Indian Nation should be Yakama Nation because this now the official name used by the Nation. | Agree. | Text changed to read "...Yakama Nation...". |
1.03C | Clarence Barnett, City of Yakima | 03/08/00 Written | 0012 | Staff Responses and Changes on Oct. 27, 1999 version indicated that this text would be changed, but the change has not been made. | This is true. Board agrees to the change. | Text changed to read "Ensuring compliance with all air quality rules and standards, permits, and programs". |
1.06D1b | Clarence Barnett, City of Yakima | 03/08/00 Written | 0013 | Objected strongly to text. He believes the source should have the sole right to determine confidentiality of records. | Staff explained that EPA insists that the Authority have the ability to make decisions about confidentiality of records. | Board, staff, and city agreed to change the text to read "Subject to review by the authority; then". |
Article 2 | ||||||
2.01C | Clarence Barnett, City of Yakima | 03/08/00 Written | 0014 | Objected to the Authority having the right to enter private property to conduct studies. | RCW 70.94.200 authorizes entry for investigations, but doesn't speak to studies. Board agreed to drop the word "studies" in the text. | Changed to read "The APCO may make reasonable investigations or inspections". |
2.01C1 | Clarence Barnett, City of Yakima | 03/08/00 Written | 0014 | Objected to the Authority having the right to enter private property to conduct studies. | RCW 70.94.200 authorizes entry for investigations, but doesn't speak to studies. Board agreed to drop the word "studies" in the text. | Changed to read "To investigate or inspect conditions for ...".". |
2.01C2 | Clarence Barnett, City of Yakima | 03/08/00 Written | 0014 | Objected to the Authority having the right to enter private property to conduct studies. | RCW 70.94.200 authorizes entry for investigations, but doesn't speak to studies. Board agreed to drop the word "studies" in the text. | Changed to read "These investigations or inspections hall be limited ...". |
2.01C2d&e | Douglas W. Rich, Chair, Bus. WG | 02/17/00, Letter | 0001 | "In the matter of Section 2.01C2d&e -Investigations of Permitted Sources:, we have earlier commented that we saw the language as proper for regular industrial and commercial sources, but potentially invasive for individual citizens at their residences." | RCW 70.94.200 denies the right of the APCO to enter nonmultiple unit private dwellings housing two families or less. In all other situations this part of WCAA permits the APCO to enter property or buildings to conduct an investigation under WCAA . Both DOE and EPA view, an entry requirement for private property which might be different from industrial / commercial property as a reduction in the WCAA requirements, and they will not support it. | None change required or made. |
2.01C2d&e | Douglas W. Rich, Chair, Bus. WG | 02/17/00, Letter | 0002 | The Authority has stated it is policy to obtain an inspection warrant if entry is refused by the occupant of the property, and coercive tactics would not be used to gain entry. | The Compliance and Enforcement Program Inspection Manual states that an inspector will use legal remedies to gain access if entry is denied to a property. | This has been discussed , and agreed that the proper place for this is in a policy manual and not the regulation. No change made in the regulation. |
2.05C | Judith Boekholder, Council Member, City of Toppenish | 03/08/00, Oral | 0025 | Would like more information in this subsection to explain how an appeal can be filed. | The appeal process is very complex with appeals being heard by the APCO, Board, or the Pollution Control Hearings Board. In addition there are different appeal procedures for different types of permits or violations. The Authority will be prepare a policy document explaining the appeal process. | No changes made in the regulation. |
Article 3 | ||||||
3.01B, 3 -5 | Clarence Barnett, City of Yakima | 03/08/00, Written | 0015 | The proposed regulation reads that "when multiple standards exist all standards will apply". This would not be possible when there are conflicting emissions standards. Requested the deletion of subsection 3.01B. | Past reviews and discussions with EPA about multiple emission standards have shown that they are very insistent that all standards apply, and the text can not be limited to the most stringent standard. | Board approved changing the second sentence to clarify this issue: "When multiple standards exist all applicable standards will apply" by add the word "applicable". |
3.01C1d, 3 - 6 | Clarence Barnett, City of Yakima | 03/08/00, Written | 0016 | The terms "odor" and "reasonable minimum" are nebulous and without standard. Significant time and funds will be spent attempting to define an odor or "reasonable minimum" in a given case. Subsection 3.01C1d should be deleted, as it is a nuisance already covered under state law in Chap. 7.48 RCW. | These terms are not defined in either Chap. 70.94 RCW or WAC 173-400-030. RCW 70.94.640 does deal with agricultural odors, and the text is repeated in subsection 3.01C3a. In both cases odors are not defined, but the law and regulation define management practices which will avoid an odor violation. The text in sub. 3.01C1d is very similar to WAC 173-400-040 (4), and it is needed to inform the public about the legal obligation for odors and to deal with nuisance complaints about odors. The evaluation of odors is very subjective, but there is no other alternative at present. | Board decided to make no change in this subsection. |
3.03D1b, 3 - 23 | Clarence Barnett, City of Yakima | 03/08/00, Written | 0017 | This subsection contains language prohibiting the burning of "hauled materials" transported from an area prohibited for outdoor burning. This is ambiguous as to the purpose and it should be deleted. | This subsection is
included to prevent
the transport of
some types of
outdoor burning
material from an
area where it is
prohibited and
burning in another
area where it is not
prohibited, and
transferring the
pollution from one
area to another. It is very similar to the text in WAC173-425-040 (2). |
Board decided to leave the text as is. |
3.03D1b, 3 - 23 | Clarence Barnett, City of Yakima | 03/08/00, Written | 0017 | This subsection contains language prohibiting the burning of "hauled materials" transported from an area prohibited for outdoor burning. This is ambiguous as to the purpose and it should be deleted. | This subsection is
included to prevent
the transport of
some types of
outdoor burning
material from an
area where it is
prohibited and
burning in another
area where it is not
prohibited, and
transferring the
pollution from one
area to another. It is very similar to the text in WAC173-425-040 (2). |
Board decided to leave the text as is. |
3.03J4a63 - 27 | Clarence Barnett, City of Yakima | 03/08/00, Written | 0018 | This subsection refers to the permittee agreeing to allow the APCO to enter his / her property to conduct an investigation. This language needs to be clarified to state that all such investigations shall be in accordance with all applicable laws with respect to private property. | The subsection states "... as defined in subsection 2.01C" which defines the requirements for entry to private property for any inspection or investigation conducted by the Authority. Therefore, additional text is not needed. | Board agreed to no change in the text. |
3.03H, 3-26 | Paul Carr, DOE | 02/18/00, E-mail | 0003 | Suggest the term "waiver" be changed to "specific exemption" to clarify the intent of use. DOE is still concerned about the potential for abuse / overuse of this subsection. The variance procedure in state law is a better approach for inclusion in the SIP. | We agree to the change in terms from "waiver" to "specific exemption". We do not agree that the variance process in subsection 3.00D and WCAA is effective for dealing with the varying conditions and short duration of impacts resulting from changed conditions during the administration of this section. This is what this subsection is intended to address. We concede that this subsection may need to be changed at the time of SIP adoption, but we believe that it is important to have in the local regulations. | Changed subsection 3.03H to
read: SPECIFIC EXEMPTIONS. The APCO (App. B) may grant a written specific exemption for a subsection if the specific exemption will: 1. Create no more air pollution than the requirements of the subsection; and 2. Create no adverse environmental, health, or public safety effects:. 3. The document granting the specific exemption must contain: a. The conditions of the specific exemption b. A duration of no more than 30 consecutive days; and c. The signature of the owner or operator of the property indicating agreement to the conditions of the specific exemption. 4. Specific exemptions will not be extended. |
3.03J1, 3-27 | Paul, Carr, DOE | 02/18/00, E-mail | 0004 | Add the text in subsection 3.03J1c to 3.03J1 to amplify the requirements for an individual permit. | This is not needed. The conditions to quality for individual permitting are all listed in 3.03J1a->e, and changing the location of the text will accomplish nothing. | None. |
3.03J2, 3-27 | Paul, Carr, DOE | 02/18/00 and 02/25/00, E-Mail | 0005 | Impose a seasonal limitation on annual residential and agricultural burning permits by inserting the following text "...the authority believes that burning can be conducted on a limited basis during those times and seasons of the year when there is minimum impact on air quality, and";... | We do not agree that imposing a seasonal limitation during March thru Oct. will reduce outdoor and agricultural burning emissions. In fact it could tend to create problems if all the burning occurs at specific times with unfavorable atmospheric conditions for ventilation. Therefore, we prefer to allow a maximum window for burning with the only limitations being those in the regulation and the state fire code. We have considered some form of limitation on types of outdoor and agricultural burning between Nov. and Feb., but that will not be considered for rule making until the PM10 maintenance plan is drafted. | None. We believed the proposed changes would be substantive and could not be adopted without refiling the regulation because they impose additional conditions on the regulated public. |
3.03, tables 1, 2, & 3, 3 - 29 -> 34 | Clarence Barnett, City of Yakima | 03/08/00, Written | 0023 | Requests exemptions for flag disposal burning similar to home barbecues with the ability to dispose of unserviceable flags at night, at locations inside the urban growth areas, using a small amount of kerosene for ignition of the fire, without a permit, and without notification to the Authority or neighbors. | Home barbecues are a form of recreational burning, and flag disposal ceremonial fires are included in the WAC and regulation definitions of recreational fires. Previous editions of the regulation included flag disposal burning as a form of recreational burning. This received strong objections from the American Legion, and all references to flag disposal burning were removed in this version of the regulation. The WAC and regulation definitions of ceremonial fires includes only Native American ceremonial fires. EPA is very insistent that no changes be made in the definitions of terms from those in the CFR, RCW, or WAC. So by default flag disposal burning becomes a type of "other recreational burning ", and is subject to the requirements of Lines 5 & 5.2 in tables 3.03 1 -> 3. Continued to the next page. | Board decided that the pollution and nuisances from this type of burning is very minor, and no changes should be made in the regulation text specifically for flag disposal burning. Flag disposal by burning will be handled as a policy matter. |
3.03, tables 1, 2, & 3, 3 - 29 -> 34 | Clarence Barnett, City of Yakima | 03/08/00, written | 0023 Cont. | Requests exemptions for flag disposal burning similar to home barbecues with the ability to dispose of unserviceable flags at night, at locations inside the urban growth areas, using a small amount of kerosene for ignition of the fire, without a permit, and without notification to the Authority or neighbors. Cont'd. | In tables 3.03 - 1 ->
3 other recreational
fires are prohibited
inside the urban
growth areas, are
permitted after
sunset, may not
burn prohibited
materials, do not
require a permit,
and have no
notification
requirements. Past statements by the Authority in the Jan. 5, '00 Staff Response and Changes on the Oct. 27th Version and at the local adoption hearing that flag disposal burning would be a type of other outdoor burning were incorrect. This is because ceremonial fires are included in the definition of recreational burning. |
Board decided that the pollution and nuisances from this type of burning is very minor, and no changes should be made in the regulation text specifically for flag disposal burning. Flag disposal by burning will be handled as a policy matter. |
3.03, tables 1, 2, & 3, 3 - 29 -> 34 | Judith Boekholder, Council Member, City of Toppenish | 03/08/00, Oral |
0028 | Shares Clarence Barnett's concerns about flag disposal burning, and is pleased to see a solution. | See comment no. 0023. | See comment no. 0023. |
3.09A&B, 3 -62 | Clarence Barnett, City of Yakima | 03/08/00, Written | 0019 | These subsections are reserved for later use, the text is not needed, and it should be removed. | Agree. Any text that is needed will be adopted in a future amendment, but the section is being reserved for mobile source emissions. | Deleted subsections 3.09 A & B, and inserted "Reserved for later use after the section title. |
3.10, 3 -62 | Clarence Barnett, City of Yakima | 03/08/00, Written | 0020 | This section is reserved for later use, it contains no text, and it should be removed. | The only text is the section number, section title, and "Reserved for later use". This is needed for the general structure of the regulation. | No change made. |
Article 4 | ||||||
None | ||||||
Article 5 | ||||||
5.02D | Dan Simmons, Mayor, City of Zillah | 03/08/00, Oral | 0029 | Concern about the size of the maximum civil penalty, and that the fines and penalty schedule and the penalty worksheets are not in the regulation. | In a previous version of the draft regulation, the Authority made the decision to remove the fines and penalty worksheets and schedules and keep them in a policy document. A general explanation was made of the fines and penalties policy process. | No change made in the regulation. |
Appendices | ||||||
App. F, F -1 | Clarence Barnett, City of Yakima | 03/08/00, Written | 0022 | This appendix is reserved for later use, it contains no text, and it should be removed. | The only text is the appendix letter, and "Reserved for later use". This is needed for the general structure of the regulation. | No change made. |
App. J, J -1 | Clarence Barnett, City of Yakima | 03/08/00, written | 0021 | This appendix is reserved for later use, it contains no text, and it should be removed. | The only text is the appendix letter, appendix title, and "Reserved for later use". This is needed for the general structure of the regulation. | No change made. |
STAFF COMMENTS, RESPONSES, AND CHANGES TO DRAFT REGULATION 1 OF THE YRCAA
Corrections Submitted to the Code Reviser are in Italic Type and Substantive changes are in Bold Type
Editorial Changes and Public Comments with the Staff Responses and Changes are in Other Documents
Section / Sub. No. & Page No. |
Person Making the Comment |
Comment No. |
Comment / Concern | Staff Response | Changes in the Regulation Text Approved by the Board |
|
Name / Organization |
Date | |||||
General Comments | ||||||
None | ||||||
Article 1 | ||||||
None | ||||||
Article 2 | ||||||
None | ||||||
Article 3 | ||||||
3.03C, 3-21 | Charlie Stansel, YRCAA | 02/22/00 | 0003 | See Public Comment No. 0003 by Paul Carr, DOE. | Changed term "waiver" to "specific exemption" in section 3.03. | Changed last part of 2nd line to read "... unless granted a limited or specific exemption by the APCO". |
3.03, table-2 footnotes | Charlie Stansel, YRCAA | 01/10/00 | ---- | The terms "yes" and "no" in this table are undefined. | Text added to clarify the meanings. | Added the following: Yes - The authority is delegated responsibility for this type of burning, a burning permit is required, or this type of burning may be delegated to another agency or business. No - The authority is not delegated responsibility for this type of burning, or this type of burning may not be delegated to another agency or business. |
3.04A , C, & D, 3 - 45 & 46 | Charlie Stansel, YRCAA | 12/23/99 | ---- | Portions of the subsections contain text with both underlining and strikeouts. | This was caused by changes in software programs which inserted incorrect underlining codes. | Underling corrected and Correction pages 3 - 45 and 46 and letter prepared on Dec. 23, '99. |
3 - 46, 3.04D5 | Charlie Stansel, YRCAA | 01/10/00 | ---- | The first two lines of subsection 3.04D5 were accidentally omitted when the Dec. 23, 1999 Correction Page was printed. | Submitted a corrected page to the Code Reviser and add the text back into the regulation. | Added the following text: 5. Existing Uncertified Wood Heater. Owners of uncertified wood heaters installed prior to January 1, 1992 may continue to use these devices at the ". |
3 - 54, 3.07F1 | Gary Pruitt, YRCAA | 01/1//00 | ---- | Grammar is incorrect. | See changes. | Changed to read to correct grammar: Survey Requirements. Before doing any renovation or demolition an asbestos survey(*) must be performed by an AHERA building inspector (*) except renovation of for an owner-occupied, single-family residences. (*) |
3 - 56, 3.07I2j | Gary Pruitt, YRCAA | 01/11/00 | ---- | Verb "be'" is incorrect and the word "slide" is misspelled. | See changes. | Edited to read: "Do not drop, throw, slide, or otherwise damage ACM waste containers; and ". |
3 - 62, 3.08B4i9) | Gary Pruitt, YRCAA | 01/11/00 | ---- | The sentence structure is awkward. | See changes. No changes made in 3.08B4i9)a) ->d). | Changed to read: "An operation and maintenance plan which also includes BMPs for;" |
3 - 64 | Gary Pruitt, YRCAA | 01/11/00 | ---- | The word "which" was omitted from the text. | See changes. | Changed to read: Any bypass of control apparatus (App. A) which was ...". |
Article 4 | ||||||
4.01 D2, 4 - 1 | Charlie Stansel, YRCAA | 02/16/00 | ---- | Page citation in the 2nd line is incorrect. | Agree. | Changed to read: "(pg. 4-1)". |
4.01D4, 4 -1 | Gary Pruitt, YRCAA | 12/29/99 | ---- | The exemptions in 4.01D4 are not consistent with WAC 173-491-040. | These need to be changed with the corrected text published in the State Register because the changes could be viewed as substantive without publication in the State Register. | Subsection 4.01D4 split into 4.01d4a->c to describe the exemptions. Correction pages 4 -1 through 4 - 4 and letter prepared on Dec. 29, '99. |
4.02E1b, 4 - 9 | Gary Pruitt, YRCAA | 02/09/00 | ---- | Wrong verb used. | Changed "shall" to "must" in the new test. | Changed to read "After the request for additional information, the applicant must provide ...". |
Article 5 | ||||||
None | ||||||
Appendix A | ||||||
Boiler, A -3 | Richard Yanez, YRCAA | 01/12/00 | ---- | Definition of boiler is inappropriate because it does not include gas or oil fired boilers. | Remove the definition and use the common industry understanding for the term. | Definition removed form Appendix A. |
New Source, A -12, Sub. 1 | Gary Pruitt, YRCAA | 02/09/00 | ---- | The word "such" makes awkward reading is not needed. | Agree. | Strikeout the word "such" in the 2nd line of subsection 1. |
Nuisance, A - 13, 2nd line | Gary Pruitt, YRCAA | 02/09/00 | ---- | The definitions is too limiting by reading "... use and enjoyment...". | Agree. | Changed to read "... use or enjoyment ...". |
Other Outdoor Burning, A - 13 | Gary Pruitt, YRCAA | 10/99 | ---- | Regulation should compare references to the proposed revision of Chap. 173-425 WAC because the timing of the adoption of this is uncertain. | Change WAC citation to the existing Chap. 173-425 WAC. | Changed to read "Any type of outdoor burning not specified in WAC 173-425-020 ...". |
Owner or Operator, A - 14 | Gary Pruitt, YRCAA | 01/13/00 | --- | The definition limits the term to only pollutants with a NAAQS and thus exempts the definition from many other pollutants. | The definition is not needed for the administration of the regulation. Industry practice and dictionaries define these terms. | Remove the entire definition from the regulation. |
Significant, A - 16 | Charlie Stansel, YRCAA | 03/02/00 | ---- | 40 CFR 52.21 (b)(23)(i) includes the metric wt. / yr. for municipal waste combustor metals. | True. | Add the following after 15 TPY "or 14 megagrams/yr" for municipal waste combustor metals. |
Solid Fuel Burning Device, A -17 | Gary Pruitt, YRCAA | 02/09/00 | ---- | Second sentence does not read correctly with "...private residence for commercial...". | Agree. | Strikeout the "f" in for, so it reads "...private residence or commercial...". |
Solid Fuel Burning Device, A -17 | Gary Pruitt, YRCAA | 02/09/00 | ---- | Last sentence should read "In regulation the phrase ...". | Agree. | Changed the word "term" to "phrase". |
Threshold Level, A -18 | Gary Pruitt, YRCAA | 02/09/00 | ---- | Change the word "applicable" to "specific". | Agree. | Change made. |
Volatile Organic Compound, A - 19, Sub. 1 | Gary Pruitt, YRCAA | 02/09/00 | ---- | The word "than" in the 1st line is not needed. | Agree | Strikeout the word, and change to read "Any organic compound except the following,...". |
Appendix B | ||||||
None | ||||||
Appendix C | ||||||
Entire appendix | Charlie Stansel | 02/11/00 | ---- | This list needs to be correct with the regulation as adopted. | Agree. | This appendix has been extensively rewritten to facilitate easy access to information in the regulation. Additional editing will be needed to produce the final copy. |
Appendix D | ||||||
None | ||||||
Appendix E | ||||||
Section 1.03, E - 1 | Gary Pruitt, YRCAA | 02/09/00 | ---- | Appendix reference in the Proposed and Comments columns for the legal land descriptions is wrong. | Agree. | Changed "App. K" to "App. H" in both columns. |
Section 9.02, E -10 | Charlie Stansel, YRCAA | 01/13/00 | ---- | Proposed subsection number is wrong and lacking a reference to App. D. | See changes. | Changed to read "3.04E1 & App. D". |
Appendix F | ||||||
None | ||||||
Appendix G | ||||||
None | ||||||
Appendix H | ||||||
None | ||||||
Appendix I | ||||||
I - 4 | Charlie Stansel, YRCAA | 02/25/00 | ----- | Map boundary for the CO nonattainment area on the south side of the area does not agree with the app. H, and the 40 CFR 81.348 description. | True. The south boundary between So. 1st and So. 16th St. is incorrectly shown on W. Washington Ave. when it should be on W. Mead Ave. | Change CO Nonattainment Area map on page I-4. |
Appendix J | ||||||
None | ||||||
Appendix K | ||||||
None | ||||||
Appendix L | ||||||
None |
STAFF EDITORIAL CHANGES MADE IN DRAFT REGULATION 1 OF THE YRCAA
Public and Staff Comments, Staff Responses, and Regulation Changes are in Other Documents
Page No. | Subsection | Person Making the Comment | Change | ||
No. | Line in Subsection | Name / Organization | Date | ||
Cover Pages | |||||
All | Header | ---- | Charlie Stansel, YRCAA | 01/07/00 | Changed to read "REGULATION 1 OF THE YRCAA, Adopted March 8, 2000". |
Unnumbered | ---- | 1st on page. | Charlie Stansel, YRCAA | 01/07/00 | Changed to read "Adopted this 8th day of March, "... |
Unnumbered | Adoption History Table | 1st row | Charlie Stansel, YRCAA | 01/07/00 | Added "March 8, 2000" as the adopted date and "May 1, 2000" as the effective date. |
Article 1 | |||||
All | Header | ---- | Charlie Stansel, YRCAA | 01/07/00 | Changed to read "REGULATION 1 OF THE YRCAA, Adopted March 8, 2000". |
1 - 1 | 1.02 | 2nd | Charlie Stansel, YRCAA | 03/07/00 | Delete "1999" in the title of the regulation. |
1 - 1 | 1.02 | 3rd | Charlie Stansel, YRCAA | 02/11/00 | Deleted an unneeded space between the " and the word regulation. |
1 - 2 | 1.03G | 1st | Gary Pruitt, YRCAA | 01/07/00 | Delete extra space between the words " business" and "and". |
1 - 2 | 1.04 | 3rd | Charlie Stansel, YRCAA | 03/07/00 | Change the term "waiver" to "specific exemption" to agree with the change in subsection 3.03H. |
1 - 4 | 1.06A | 2nd | Gary Pruitt, YRCAA | 01/07/00 | Changed the word "availability" to "available". |
1 - 4 | 1.06D1a | 3rd | Gary Pruitt, YRCAA | 01/07/00 | Deleted extra space between the words "adverse" and "affect" and changed the word" "affect" to "effect". |
1.07B1 | Last | Charlie Stansel, YRCAA | 03/10/00 | Remove comma at the end of the subsection and replace with "...; or". | |
1.07B2 | Last | Charlie Stansel, YRCAA | 03/07/00 | Delete comma at the end of sentence and replace with a period. | |
1 - 6 | 1.09 | 2nd | Gary Pruitt, YRCAA | 01/07/00 | Inserted the word "of" between " as" and "the". |
Article 2 | |||||
All | Header | ---- | Charlie Stansel, YRCAA | 01/07/00 | Changed to read "REGULATION 1 OF THE YRCAA, Adopted March 8, 2000". |
2 - 2 | 2.01F1 | 2nd | Gary Pruitt, YRCAA | 01/07/00 | Deleted an extra space between the words "regulatory" and "or". |
2 - 2 | 2.01G | 3rd | Gary Pruitt, YRCAA | 01/07/00 | Deleted an extra space between the words"these" and "regulations". |
2 - 3 | 2.03 | 3rd | Gary Pruitt, YRCAA | 01/07/00 | Correct the spelling of the word implements by deleting the second "l". |
Article 3 | |||||
All | Header | ---- | Charlie Stansel, YRCAA | 01/07/00 | Changed to read "REGULATION 1 OF THE YRCAA, Adopted March 8, 2000". |
3 - 4 | 3.00D5b1) | 1st | Gary Pruitt, YRCAA | 01/07/99 | Added one space between "1)" and "Will". |
3 - 5 | 3.00E1 | 2nd | Gary Pruitt, YRCAA | 01/07/00 | Deleted an extra space between "(App. A)" and " "to". |
3 - 5 | 3.01C1 | 1st | Charlie Stansel, YRCAA | 02/11/00 | Make subsection no. and title bold face type. |
3 - 8 | 3.01C2c2) | 1st | Gary Pruitt, YRCAA | 01/07/00 | Inserted an "a" before the word "source". |
3 - 9 | 3.01D3 | 1st | Gary Pruitt, YRCAA | 01/07/00 | The "3" is in bold type face. |
3 - 13 | 3.02D1 | 1st | Gary Pruitt, YRACC | 01/07/00 | Add a second space following "Purpose.". |
3 - 13 | 3.02D2 | 1st | Gary Pruitt, YRACC | 01/07/00 | Add a second space following "Applicability.". |
3 - 13 | 3.02D3 | 1st | Charlie Stansel, YRCAA | 01/07/00 | Delete an extra space following "Requirements.". |
3 - 14 | 3.02, table 3.02-1 | Rows 3 -> 5 | Charlie Stansel, YRCAA | 01/07/00 | Change to 10 pt. type. |
3 - 15 | 3.02, table 3.02-2 | Row 2 | Charlie Stansel, YRCAA | 01/07/00 | Changed to 10 pt. type. |
3 - 15 | 3.02, table 3.02-2 | ---- | Charlie Stansel, YRCAA | 01/07/00 | Add top border to the box for the table, and correct the line weights. |
3 - 21 | 3.03C1 | 1st | Gary Pruitt, YRCAA | 01/07/00 | Add a second space following "Prohibitions.". |
3 - 23 & 24 | 3.03D | All | Charlie Stansel, YRCAA | 03/15/00 | Correct tabbing for the subsection. |
3 - 25 | 3.03E3 | 1st | Gary Pruitt, YRCAA | 01/07/00 | Misnumbered. Subsection number changed to 3.03E5. |
3 - 25 | 3.03G2a | 1st | Gary Pruitt, YRCAA | 01/07/00 | Delete an extra space between "when" and "a". |
3 - 26 | 3.03H | All | Charlie Stansel, YRCAA | 03/15/00 | Correct tabbing for the subsection. |
3 - 26 | 3.03I | All | Charlie Stansel, YRCAA | 03/15/00 | Correct tabbing for the subsection. |
3 - 26 -> 28 | 3.03J | All | Charlie Stansel, YRCAA | 03/15/00 | Correct tabbing for the subsection. |
3 - 27 | 3.03J1b | 1st | Gary Pruitt, YRCAA | 01/07/00 | Delete the word "a". |
3 - 29 | 3.03, table 3.03-1 | ---- | Charlie Stansel, YRCAA | 01/10/00 | Change line weight to the same for all lines in the table. |
3 - 29 | 3.03, table 3.03-1 | 2.4 and 2.5 | Charlie Stansel, YRCAA | 02/23/00 | Correct table row spacing so the correct text lines up with lines 2.4 and 2.5. |
3 - 33 | 3.03, table 3.03-3 | Line 15 | Charlie Stansel, YRCAA | 02/25/00 | Correct the spelling of the word "annual". |
3 - 37 | 3.03, GRP 3.03-2, subsection A | 2nd | Gary Pruitt, YRCAA | 01/10/00 | Remove extra period at the end of the sentence. |
3 - 46 | 3.04C1b1)&2) | 1st in both | Gary Pruitt, YRCAA | 01/10/00 | Set spacing between subsection number and text to be consistent with rest of the regulation. |
3 - 46 | 3.04D | All | Charlie Stansel, YRCAA | 03/15/00 | Correct tabbing of the subsection. |
3 - 46 | 3.04D3 | 1st | Charlie Stansel, YRCAA | 02/22/00 | Remove underlining under the word" Cookstoves" in the subsection title, and leave the strikeout through the word. |
3 - 46 | 3.04D5 | 1st | Gary Pruitt, YRCAA | 01/10/00 | Correct the spelling of the word "heaters". |
3 - 47 | 3.04E | All | Charlie Stansel, YRCAA | 03/15/00 | Correct tabbing of the subsection. |
3 - 47 | 3.05A | All | Charlie Stansel, YRCAA | 03/15/00 | Correct tabbing of the subsection. |
3 - 50 | 3.05, table 3.05-2 | Row 3 | Gary Pruitt, YRCAA | 01/10/00 | Correct tabbing for Fire Training Fires. |
3 - 54 | 3.07F2c | 2nd | Gary Pruitt, YRCAA | 01/10/00 | Delete second period at end of sentence. |
3 - 55 | 3.07H1b | 1st | Gary Pruitt, YRCAA | 01/10/00 | Delete extra space between "an" and "unaltered". |
3 - 56 | 3.07H31)->3) | ---- | Charlie Stansel, YRCAA | 01/11/00 | Corrected subsection numbering to 3.07H3a->c. |
3 - 56 | 3.07H33)a)&b) | ---- | Charlie Stansel, YRCAA | 01/11/00 | Corrected subsection numbering to 3.07H3c1)&2) |
3 - 56 | 3.07H3c2) formerly 3.07H33)b) | 2nd | Gary Pruitt, YRCAA | 01/11/00 | Change the word demolitions to demolition. |
3 - 56 | 3.07I2i3) | 1st | Charlie Stansel, YRCAA | 03/15/00 | Put a period at the end of this subsection. |
3 - 58 | 3.07I3 | 1st | Gary Pruitt, YRCAA | 01/11/00 | Insert one additional space after subsection title. |
3 - 59 | 3.08A3c1) | 2nd | Gary Pruitt, YRCAA | 01/11/00 | Change the word "or" to "of" to give the correct meaning to the subsection. |
3 - 59 ->61 | 3.08A4d->i | ---- | Charlie Stansel, YRCAA | 03/15/00 | Renumbered to 3.08A4c->h to correct a numbering error. |
3 - 61 | 3.08B3c | 2nd | Gary Pruitt, YRCAA | 01/11/00 | Put a period at the end of the subsection following the word "loses". |
3 - 61 & 62 | 3.08B4d->i | ---- | Charlie Stansel, YRCAA | 03/15/00 | Renumbered to 3.08B4b->g to correct a numbering error, and put a period at the end of 3.08B4b (formerly 3.08B4d). |
3 - 61 | 3.08B4h1) renumbered to 3.08B4f1) | 1st | Gary Pruitt, YRCAA | 01/11/00 | Delete the word "of" between the words "more" and "cattle". |
3 - 62 | 3.11 | Section Title | Charlie Stansel, YRCAA | 01/11/00 | Removed underlining for the word "'Special" in the Title. |
3 - 65 | 3.11D4c | 2nd | Charlie Stansel, YRCAA | 01/11/00 | Remove underlining for the word "such". |
3 - 65 | 3.11E2b1) | 1st | Gary Pruitt, YRCAA | 01/11/00 | Insert second space after subsection title. |
Article 4 | |||||
All | Header | ---- | Charlie Stansel, YRCAA | 01/11/00 | Changed to read "REGULATION 1 OF THE YRCAA, Adopted March 8, 2000". |
4 - 1 | 4.01D3 | 1st | Charlie Stansel, YRCAA | 02/16/00 | Changed to word "Pollutants" to "Pollutant" in the subsection title. |
4 - 4 | 4.01F2c2) | 1st | Gary Pruitt, YRCAA | 01/11/00 | Changed the word "inventory" to "inventories". |
4 - 4 | 4.01F3b | 2nd | Gary Pruitt, YRCAA | 01/11/00 | Delete space after the word "apparatus". |
4 - 5 | 4.01G | 2nd | Gary Pruitt, YRCAA | 02/09/00 | Strikeout the word "in" before "Article XIII, Section 13.01". |
4 - 9 | 4.02E4b | 1st | Gary Pruitt, YRCAA | 02/09/00 | Replace ";" with a "." at the end of the subsection. |
Article 5 | |||||
All | Header | ---- | Charlie Stansel, YRCAA | 01/13/00 | Changed to read "REGULATION 1 OF THE YRCAA, Adopted March 8, 2000". |
5 - 2 | 5.02C | 1st | Charlie Stansel, YRCAA | 03/02/00 | Changed "C" to "c" in "Chap. 70.94 RCW to agree with rule format. |
5 - 3 | 5.02D1 | 2nd & 3rd | Charlie Stansel, YRCAA | 03/02/00 | Changed "Chap." to "chap." and "Chapter" to "chap." to agree with rule format. |
Appendix A | |||||
All | Header | ---- | Charlie Stansel, YRCAA | 01/13/00 | Changed to read "REGULATION 1 OF THE YRCAA, Adopted March 8, 2000". |
A - 1 | Actual Emissions | 2nd | Gary Pruitt, YRCAA | 02/09/00 | Change the word "emission" to "emissions". |
A - 5 | Emission Reduction Credit (ERC) | 2nd | Charlie Stansel, YRCAA | 03/02/00 | Changed WAC 173-400-131 from italic to regular type face. |
A - 7 | Furnace | 6th | Gary Pruitt, YRCAA | 02/09/00 | Changed the word "form" to "from" to correct spelling. |
A - 8 | Hour | 1st | Charlie Stansel, YRCAA | 03/02/00 | Add a "(" before WAC 173-435-020 (4)). |
A - 9 | Major Modification, subsection 5a | 4th | Gary Pruitt, YRCAA | 02/09/00 | Inserted a space between "CFR" and "51". |
A - 10 | Major Stationary Source, ¶5s | 1st | Charlie Stansel, YRCAA | 03/02/00 | Delete an extra space before the "s". |
A -16 | Significant, Total Reduced Sulfur | ---- | Gary Pruitt, YRCAA | 02/09/00 | Changed "TSR" to correct abbreviation "TRS". |
A - 18 | State Implementation Plan | 2nd | Gary Pruitt, YRCAA | 02/09/00 | Insert the verb "be" before "submitted to ecology...". |
A - 16 | Significant | ---- | Charlie Stansel, YRCAA | 01/13/00 | Align emission rate numbers and column title. |
A - 19 | Unclassifiable | 2nd & 3rd | Charlie Stansel, YRCAA | 02/14/00 | Correct tabbing. |
Appendix B | |||||
All | Header | ---- | Charlie Stansel, YRCAA | 01/13/00 | Changed to read "REGULATION 1 OF THE YRCAA, Adopted March 8, 2000". |
Appendix C | |||||
All | Header | ---- | Charlie Stansel, YRCAA | 01/13/00 | Changed to read "REGULATION 1 OF THE YRCAA, Adopted March 8, 2000". |
Appendix D | |||||
All | Header | ---- | Charlie Stansel, YRCAA | 01/13/00 | Changed to read "REGULATION 1 OF THE YRCAA, Adopted March 8, 2000". |
D - 3 | Notes | ---- | Charlie Stansel, YRCAA | 01/13/00 | Insert a tab to the left of the "Notes" to align it with "Footnotes". |
Appendix E | |||||
All | Header | ---- | Charlie Stansel, YRCAA | 01/13/00 | Changed to read "REGULATION 1 OF THE YRCAA, Adopted March 8, 2000". |
Appendix F | |||||
All | Header | ---- | Charlie Stansel, YRCAA | 01/13/00 | Changed to read "REGULATION 1 OF THE YRCAA, Adopted March 8, 2000". |
F - 1 | Appendix Title | ---- | Charlie Stansel, YRCAA | 01/13/00 | Changed from "Fee Schedules" to "(Reserved for Later Use)" because this appendix is not used in the adopted regulation. |
F - 1 -> 6 | Entire appendix | ---- | Charlie Stansel, YRCAA | 01/13/00 | Deleted the entire appendix because it is not used in the adopted regulation. |
Appendix G | |||||
All | Header | ---- | Charlie Stansel, YRCAA | 01/13/00 | Changed to read "REGULATION 1 OF THE YRCAA, Adopted March 8, 2000". |
Appendix H | |||||
All | Header | ---- | Charlie Stansel, YRCAA | 01/13/00 | Changed to read "REGULATION 1 OF THE YRCAA, Adopted March 8, 2000". |
Appendix I | |||||
All | Header | ---- | Charlie Stansel, YRCAA | 01/13/00 | Changed to read "REGULATION 1 OF THE YRCAA, Adopted March 8, 2000". |
Appendix J | |||||
All | Header | ---- | Charlie Stansel, YRCAA | 01/13/00 | Changed to read "REGULATION 1 OF THE YRCAA, Adopted March 8, 2000". |
Appendix K | |||||
All | Header | ---- | Charlie Stansel, YRCAA | 01/13/00 | Changed to read "REGULATION 1 OF THE YRCAA, Adopted March 8, 2000". |
K - 3 | A8bb & dd | All lines | Charlie Stansel, YRCAA | 02/09/00 | Align left hand nargub of text with the rest of the text in this subsection. |
K - 4 | A8gg & hh | All lines | Charlie Stansel, YRCAA | 02/09/00 | Align left hand nargub of text with the rest of the text in this subsection. |
K - 10 | B1b, Table K-2 | Table headings | Gary Pruitt, YRCAA | 02/09/00 | Make text bold face type to be consistent with other table headings. |
K - 10 | Table K -2 | 2nd row | Charlie Stansel, YRCAA | 01/13/00 | Turn off table border under the number "0.0007700" for Acrylamide. |
Appendix L | |||||
All | Header | ---- | Charlie Stansel, YRCAA | 01/13/00 | Changed to read "REGULATION 1 OF THE YRCAA, Adopted March 8, 2000." |
L - 1 | Footer | ---- | Charlie Stansel, YRCCA | 02/09/00 | Manually type the page number "L - 1" at the bottom of the page. |
Number of Sections Adopted in Order to Comply with Federal Statute: New 0, Amended 0, Repealed 0; Federal Rules or Standards: New 0, Amended 0, Repealed 0; or Recently Enacted State Statutes: New 0, Amended 0, Repealed 0.
Number of Sections Adopted at Request of a Nongovernmental Entity: New 0, Amended 0, Repealed 0.
Number of Sections Adopted on the Agency's Own Initiative: New 34, Amended 0, Repealed 48.
Number of Sections Adopted in Order to Clarify, Streamline, or Reform Agency Procedures: New 34, Amended 0, Repealed 48.
Number of Sections Adopted Using Negotiated Rule Making: New 0, Amended 0, Repealed 0; Pilot Rule Making: New 0, Amended 0, Repealed 0; or Other Alternative Rule Making: New 0, Amended 0, Repealed 0. Effective Date of Rule: May 1, 2000.
March 21, 2000
Les Ornelas
Air Pollution Control Officer
OF THE
YAKIMA, WASHINGTON 98901
Adopted this 8th day of March, 2000 by the | ||
Board of Directors, Yakima Regional Clean Air Authority | ||
Yakima, Washington | ||
Chairperson | ||
Member | ||
Member | ||
Member | ||
Member |
REGULATION 1 OF THE YAKIMA REGIONAL
CLEAN AIR AUTHORITY
Amend. No. |
Dates | Action | Sections | |
Adopted | Effective | |||
N/A | March 8, 2000 | May 1, 2000 | Adoption of Regulation 1 |
All |
1 | ||||
2 | ||||
3 |
1.01 NAME OF AUTHORITY (New section)
This agency is known as the Yakima Regional Clean Air Authority, and in this regulation it is referred to as the "authority".
1.02 SHORT TITLE (1.02)
These rules and This body of regulations shall is be known
and cited as the "Restated Regulation 1 of the Yakima (County)
Regional Clean Air Authority" and from this section forward it
will be referred to as the "regulations".
1.03 POLICY
This section implements Washington Clean Air Act (WCAA) by doing the following:
A. PUBLIC POLICY. (1.01) It is declared to be the public
policy of the Yakima County Clean Air Authority to secure and
maintain Securing and maintaining such levels of air quality as
that will:
1. Protect human health and safety;
2. Prevent injury to plant and animal life and property;
3. Foster the comfort and convenience of the inhabitants of
Yakima County;
4. Promote the economic and social development; of Yakima
County;
5. Facilitate the enjoyment of the natural attractions
therein;
6. Prevent or minimize the transfer of air pollution (App. A) to other resources;
7. Ensure equity and consistency with the FCAA (App. B) and WCAA (App. B);
8. Educate and inform the citizens of Yakima Co. on air quality matters;
9. Maintain accurate and current policies, regulations, and rules;
10. Perform administrative actions in a timely and effective manner; and
11. Therein, and further to Cooperate with the local
governments, the Yakama Nation, organizations or citizens on air
quality matters in achieving the policy objectives as set forth
herein throughout the whole of Yakima County.
B. PROCEDURES AND STANDARDS. Controlling air pollution through procedures, standards, permits, and programs.
C. COMPLIANCE WITH ADOPTED STANDARDS. Ensuring compliance with all air quality rules and standards, permits, and programs.
D. COOPERATION AND COORDINATION. Cooperating and coordinating with federal, state, county, local, and tribal governments; governmental agencies; organizations; businesses; and the public in all matters related to air pollution characterization, measurement, and control.
E. STRATEGIC PLANNING. Developing strategies to avoid, reduce, or prevent air pollution through:
1. Innovative solutions;
2. Early planning; and
3. The integration of air pollution control in the work of other agencies and businesses.
F. GUIDELINES. Preparing guidelines which interpret, implement, and enforce these regulations.
G. BUSINESS ASSISTANCE POLICY. Providing reasonable business and technical assistance to the community.
H. STATE ENVIRONMENTAL POLICY ACT (SEPA). Fully complying with all the requirements of the SEPA (App. B) and holding other agencies, businesses, and individuals accountable for decisions within the jurisdiction of the authority.
I. STATE IMPLEMENTATION PLAN (SIP). Fully complying with the SIP (App. B). Changes in the SIP will be implemented through general rules or regulatory orders.
1.04 CAUSING OR PERMITTING AIR POLLUTION UNLAWFUL - EXCEPTION
GENERAL APPLICABILITY (2.01)
Except where specified in a variance permit, as provided
herein, it shall be unlawful for any person to cause air
pollution or permit it to be caused in violation of these rules
and Regulations.
All activities, persons, and businesses under the jurisdiction of this authority are subject to all provisions of these regulations except as described in a variance issued under subsection 3.00D (pg. 3-xx), a specific exemption granted under subsection 3.03H (pg. 3-xx), or granted exemptions from specific subsections. Implementation of these regulations may be through permits or orders that provide for equal or greater effectiveness in minimizing the effects of an existing or potential source of air pollution.
1.05 ROLES AND RESPONSIBILITIES
A. THE AUTHORITY. The authority is a municipal corporation with the rights described in WCAA (App. B) and exercising jurisdiction within Yakima County, WA.
B. THE BOARD OF DIRECTORS. The governing body of the authority is the board of directors. The board has the power to:
1. Adopt, amend and repeal its own rules and regulations in accordance with RCW 42.30, Open Public Meeting Act and RCW 34.05, Administrative Procedure Act;
2. Hold hearings relating to any aspect related to the administration of WCAA and other applicable law;
3. Issue any orders necessary to carry out the functions of WCAA and enforce them by all appropriate administrative and judicial proceedings;
4. Require access to records, books, files and other information specific to the control, recovery or release of air pollutants into the atmosphere;
5. Obtain necessary scientific, technical, administrative and operational services, including laboratory facilities, by contract or otherwise;
6. Prepare and develop comprehensive plans for the prevention, abatement and control of air pollution;
7. Encourage voluntary cooperation by persons or affected groups to achieve the purposes of the state and federal laws and regulations;
8. Encourage and conduct studies, investigation and research relating to air pollution and its causes, effects, prevention, abatement and control;
9. Collect and disseminate information and conduct educational and training programs relating to air pollution;
10. Consult, cooperate, or contract with other agencies, departments, educational institutions, governments, and interested persons or groups; and
11. Accept, receive, disburse and administer grants or other funds or gifts from any source, including public and private agencies and the United States government for the purpose of carrying out the functions of WCAA and other applicable laws.
C. THE AIR POLLUTION CONTROL OFFICER. (2.02 A) The air pollution
control officer (APCO) is appointed by the board. The Control
Officer shall APCO observes and enforces state and federal laws,
orders, ordinances, resolutions or rules and regulations of the
authority pertaining to the control and prevention of air
pollution.
D. ADVISORY COUNCIL. (2.05) The board of the Authority may in
its discretion appoint an advisory council to advise and consult
with the board and with the Control Officer APCO in effectuating
implementing the purposes of these regulations. The board may
submit to the advisory council recommendations for the adoption
or modification or of regulations or emission standards or other
matters that it considers appropriate, but shall not be required
to do so.
1.06 RECORDS
A. PURPOSE. To define the policy for protecting records and making them available to the public.
B. APPLICATION. To provide access to any information available under federal or state law concerning the business of the authority. The provisions of this section shall be interpreted to assure continuing public confidence in the authority.
C. PUBLIC RECORDS.
1. Availability. All public records of the authority are available for public inspection and copying during normal working hours at the office of the authority.
2. Legal Exemptions. Availability of public records is subject to exemptions and requirements of RCW 42.17.310 and RCW 70.94.205.
3. Process. All requests for records shall be processed according to RCW 42.17 and the current fee schedule.
D. CONFIDENTIAL RECORDS. (2.04)
1. Availability. Whenever the authority obtains any records
or other information, other than ambient air quality data or
emission data, are furnished to or obtained by the Yakima County
Clean Air Authority under this regulation which:
a. The owners or operators certify in writing that the information relates to unique processes or production or the release of the information will likely have an adverse effect on the competitive position of the source; and
b. Subject to review by the authority; then
c. relates to processes or production unique to the owner or
operator, or is likely to (adversely) affect the competitive
position of such owner or operator (of said processes or
production,) and the owner or operator of such processes or
production so certifies, such records or The information shall be
is only for the confidential use of the Board authority.
2. Summaries for Publication. Nothing herein shall be
construed to prevent The authority may use of records or
confidential information by the Board in to compile or publishing
analysies or summaries relating to the general condition of the
outdoor atmosphere; if:
a. provided, that such The analysies or summaries do not
reveal any information otherwise confidential under the
provisions of this subsection; and
b. provided further, that The emission data furnished given
to or obtained by the Board shall be the authority is correlated
with applicable emission limitations and other control measures
and shall be available for public inspection during normal
business hours at the office of the Board authority.
1.07 GENERAL PROVISIONS
A. COMPLIANCE. Failure to comply with any of the following is a violation of this regulation, and may result in either civil or criminal penalties;
1. FCAA (App. B),
2. WCAA (App. B),
3. CFR issued by EPA,
4. WAC issued by ecology,
5. Any section, subsection, or appendix of this regulation,
6. Any permit requirement, or
7. Any order or approval issued by the authority.
B. FALSE OR MISLEADING INFORMATION. No person shall:
1. Statements. (2.03A) willfully make a false or misleading
statement to the Board as to any matter within the jurisdiction
of the Board. (WAC 173-400-105(7)) Make any false materials
statement, representation or certification in any form, notice or
report required under this regulation, resolution, permit or
order of the authority or by WCAA (App. A); or
2. Monitoring Devices. (WAC 173-400-105(8)) Render inaccurate any monitoring device or method required under this regulation, resolution, permit or order of the authority or by WCAA (App. A).
C. ALTERED DOCUMENTS. (2.03 B) No person shall reproduce or
alter or cause to be reproduced or altered any order,
registration certificate, or other paper issued by the authority
if the purpose of such reproduction or alteration is to which
evades or violates or aids the evasion or violation of any
provision of this regulation or any other law.
D. AVAILABILITY OF ORDERS. (2.03C) Any order or registration certificate required to be obtained by this regulation, shall be available on the premises designated on the order or certificate.
E. POSTING OF NOTICES. (2.03D) In the event that the authority
requires a notice to be displayed, it shall be posted. No person
shall mutilate, obstruct or remove any notice posted by the
authority unless authorized to do so by the board.
PRIMA FACIE EVIDENCE. (5.02B) It shall be prima facie evidence
that the person who owns or controls property on which outdoor
burning occurs has allowed or caused such open fire.
F. SEVERABILITY. (8.05) If (any phrase, clause, subsection,
or) a section of this regulation (shall be) is declared
unconstitutional or the application of a section is held invalid,
(by any court of competent jurisdiction to any person shall be
conclusively presumed that the Board of Directors would have
enacted this Regulation without the phrase, clause, subsection,
or section so held unconstitutional or invalid and) the remainder
of the regulation shall not be affected as a result of said part
being held unconstitutional or invalid, nor shall that provision
be affected by other persons or circumstances.
G. WAIVER. (5.12C) Nothing in this regulation shall be
construed is intended to impair any cause of action or legal
remedy therefore of by a person or the public, for or the injury
or damage arising from the emission from of any air contaminant
in such place, manner or concentration as to constitute air
pollution or a common law nuisance.
H. REVISIONS. The board may elect to open the entire regulation, an article, individual sections, specific subsections, or appendices for future revision at any time without opening the remainder of the regulation.
I. DISCLAIMER. Nothing in this regulation relieves a person (App. A) from the obligation to comply with laws, regulations, and standards of state or federal agencies.
J. DEFINITIONS, ACRONYMS, AND ABBREVIATIONS.
1. Commonly Used Definitions. The definitions of terms and phrases used in more than one section of the regulation are located in appendix A, and they are identified in the text with (App. A) following the term. When a definition is copied or abstracted from another source, the source is identified.
2. Commonly Used Acronyms and Abbreviations. Commonly used acronyms and abbreviations are defined in appendix B, and they are identified in the text with (App. B).
3. Specific Definitions. The definitions of terms and phrases used in only one section of the regulation are located in the beginning of the section, and they are identified in text with a (*) following the term.
4. Part of the Regulation. The definitions of terms, phrases, acronyms, and abbreviations are an integral part of this regulation.
1.08 EFFECTIVE DATE. (New Section) These regulations are effective May 1, 2000.
1.09 REVOCATIONS. (New Section) The following are revoked or replaced by sections of this regulation as of the effective date of the regulation:
A. Restated Regulation 1 of the Yakima County Clean Air Authority with the following effective dates:
1. November 18, 1993.
2. January 13, 1994.
3. June 20, 1994.
4. October 20, 1994.
5. December 15, 1995.
B. Board Resolutions. None
C. Board Decisions. None.
ARTICLE 2 - GENERAL REGULATIONS
2.01 AIR POLLUTION CONTROL OFFICER - POWERS AND DUTIES
A. POWERS AND DUTIES. The board shall appoint an air pollution control officer (APCO) competent in the field of air pollution control whose responsibility shall be to implement these regulations in a manner consistent with:
1. Applicable federal and state laws and regulations;
2. County and/or city municipal ordinances where they are at least as stringent and effective as those of the authority; and
3. The air pollution control officer and assistants, in the
performance of their duties, shall in all respects be subject to
the direction of the board and take no action that has been
prohibited by the board. (2.02E) Policies and directives of the
board unless specifically limited elsewhere in this regulation or
by other laws or regulations.
B. DELEGATED AUTHORITY. When the term "APCO" is used in this regulation, it also applies to any authorized representative of the authority conducting official business for the APCO (App. B) and the authority.
C. INVESTIGATIONS. (2.02B) The control officer APCO or his
duly authorized agent may make any reasonable investigations or
inspections. or study which is necessary for the purpose of to
enforce this regulation or any amendment. hereto or controlling
or reducing the amount of or kind of air contaminant. The
Control Officer shall be required to maintain appropriate records
and prepare periodic reports to the Board.
1. Purpose of Investigations. (2.02C) For the purpose of To
investigateing, or inspect or study conditions for specific to
the control, recovery or release of air contaminants pollutants
into the atmosphere.
2. Scope of Investigations. These investigations or inspections shall be limited to investigating and/or enforcing the following:
a. Bona fide complaints about an alleged violation of this regulation, an amendment, or revision;
b. An alleged or actual violation of this regulation, an amendment, or revision;
c. An alleged or actual violation of a federal or state law or regulation enforced by the authority;
d. Any permit, order, or condition of approval issued by the authority;
e. Periodic testing and inspection of any source (app. A); or
f. Any records, files, or other information that relate to subsection 2.01C1 (pg. 2-1).
3. Entry for Investigations. (2.02C)
a. The control officer or his duly authorized representative, shall have the power to enter any private or public property at reasonable times.
b. Non-multiple unit private dwellings housing two (2) families or less may not to be entered without the permission of the occupant(s) of dwelling(s).
c. No person shall refuse entry or access to the control officer.
4. Obstruction of an Investigation. Nor shall any person obstruct, hamper or interfere with such inspection, or study.
D. RIGHT TO OBTAIN SAMPLES. (2.02D)
1. Notification of Owner or Lessee. If, during the course
of an inspection, the APCO a(n) authorized employee of the
Authority, during the course of an inspection, desires to obtain
a sample of air contaminant, fuel, process material or other
material which affects or may affect the emission of air
contaminants, he the APCO shall notify the owner or lessee of the
time and place of obtaining a sample.
2. Owner/Operator Sampling.
a. So The owner or operator lessee has the opportunity to
may take a similar sample at the same time, and place, and method
as the sample taken by the APCO authority.
b. As an alternative the owner or operator may request a representative portion of the sample taken by the APCO.
c. The representative sample shall not be provided to the owner or operator if the actions needed to obtain the representative sample can compromise the ability of the APCO to obtain an accurate sample.
3. Receipt for Sample. If requested the APCO authorized
employee of the Authority shall give a receipt to the owner or
lessee operator for the sample obtained.
E. MAINTAIN RECORDS. (2.02B) The APCO shall maintain appropriate records and prepare periodic reports to the board.
F. SIGNING AUTHORITY. The APCO is authorized by the board to take the following actions for the authority:
1. To sign official complaints, issue notices of violations, impose penalties, issue permits, sign regulatory or approval orders, sign contracts, and administrative correspondence.
2. To approve SEPA (App. B) documents as the Responsible Official.
3. To apply to any court for necessary orders.
G. LEGAL ACTION. When the board approves, the APCO may commence legal action. Nothing in this regulation may be construed to limit the APCO from using any other legal means to enforce the provisions of these regulations.
2.02 AUTHORITY TO COLLECT FEES
A. LEGAL AUTHORITY. WCAA (App. B) authorizes the authority to assess fees and recover costs for permits, registrations, and professional services.
B. CHARGES. Charges include but are not limited to the following:
1. Reimbursement of authority staff time for review of complex projects or lengthy enforcement actions;
2. Costs incurred by the authority for the implementation of the air operating permit program as defined in WAC 173-401-905 and WAC 173-401-940(1).
3. Reimbursement of authority staff time for costs to prepare notices of construction and initial SM (App. A & B) regulatory orders;
4. Reimbursement to a minimum of 50% of the cost for annual registrations including periodic inspections;
5. Charges from Ecology (App. B) for state level support and oversight work; and
6. Appropriate charges incurred by other agencies and requested to be collected shall be billed as part of a penalty.
C. REFUNDS.
1. The following fees are non-refundable:
a. Actual costs incurred by the authority.
b. Application fees.
2. Fees collected in excess of actual costs will be refunded without interest.
3. Fees collected in error will be refunded with interest.
D. FEES.
1. Adoption of Fee Schedules. Fee schedules shall be adopted by board resolution under the authority of RCW 42.30 at any time after receiving public comment.
2. Availability of Fee Schedules and Related Information.
(13.05D) The workload analysis budget and fee allocations
schedule and billing rate schedule for reimbursable fees shall be
made available upon request. Any proposed revisions to the
annual fee schedule shall be presented to the board for adoption
after public notice has been given.
2.03 ADOPTION OF APPLICABLE STATE AND FEDERAL REGULATIONS
The Yakima County Clean Air authority hereby adopts by
reference and incorporates herein, as if specifically set forth
herein; all of the terms and provisions of implements and
enforces the following The Yakima County Clean Air authority
hereby adopts by reference and incorporates herein, (as if
specifically set forth herein,) all of the terms and provisions
of the as identified below: (Washington) State administrative
codes WAC (App. B) and code of federal regulations CFR (App. B)
as identified below, except. as the same may be less stringent
than the provisions of this regulation of the Yakima County Clean
Air Authority.
A. STATE REGULATIONS. (12.01)
Chapter 173-400 WAC General Regulations for Air Pollution Sources;
Chapter 173-401 WAC Operating Permit Regulation;
Chapter 173-420 WAC Conformity of Transportation Activities to Air Quality Implementation Plans;
Chapter 173-425 WAC Open Burning;
Chapter 173-430 WAC Agricultural Burning;
Chapter 173-433 WAC Solid Fuel Burning Device Standards;
Chapter 173-434 WAC Solid Waste Incinerator Facilities;
Chapter 173-435 WAC Emergency Episode Plans;
Chapter 173-450 WAC Establishing Requirements for the Receipt of Financial Aid;
Chapter 173-460 WAC Controls for New Sources of Toxic Air Pollutants;
Chapter 173-470 WAC Ambient Air Quality Standards For Particulate Matter;
Chapter 173-474 WAC Ambient Air Quality Standards for
Sulphur Oxides Standards;
Chapter 173-475 WAC Photochemical Oxidant, Hydrocarbons,
Nitrogen Dioxide (Ambient Standards) Ambient Air Quality
Standards for Carbon Monoxide, Ozone, and Nitrogen Dioxide;
Chapter 173-481 WAC Ambient Air Quality and Environmental Standards for Fluorides.
Chapter 173-490 WAC Emission Standards and Controls for
Sources Emitting Volatile Organic Compounds (VOC);
Chapter 173-491 WAC Emission Standards and Controls for Sources Emitting Gasoline Vapors;
Chapter 173-806 WAC Model Ordinance; and
Chapter 197-11 WAC SEPA (App. B) Rules.
B. FEDERAL REGULATIONS. (12.02)
40 CFR Part 50 National Primary and Secondary Ambient Air Quality Standards;
40 CFR Part 51 Requirements for Preparation, Adoption, and Submittal of Implementation Plans;
40 CFR Part 52 Approval and Promulgation of Implementation Plans;
Subpart A General Provisions; and
Subpart WW Washington;
40 CFR Part 58 Ambient Air Quality Surveillance;
40 CFR Part 60 (New Source Performance) Standards of
Performance for New Stationary Sources ((NSPS));
40 CFR Part 61 National Emissions Standards for Hazardous Air Pollutants (NESHAPS);
40 CFR Part 63 National Emission Standards for Hazardous Air Pollutants for Source Categories;
40 CFR Part 64 Compliance Assurance Monitoring;
40 CFR Part 68 Chemical Accident Prevention Provisions;
40 CFR Part 70 State Operating Permit Programs;
40 CFR Part 82 Protection of Stratospheric Ozone.;
40 CFR Part 503, Standards for the Use or Disposal of Sewage Sludge;
Subpart A, General Provisions;
Subpart E, Incineration; and
40 CFR Part 763 Asbestos Model Accreditation Plan.
2.04 PUBLIC PARTICIPATION. (WAC 173-400-171)
A. PURPOSE. To involve the public prior to making decisions.
B. APPLICABILITY. This section applies to the following actions or situations:
1. NSR (App. B) applications for a new or modified source or
emissions unit if the application proposesd a significant (App.
A) net increase in emissions of any pollutant regulated by state
or federal law or regulations; source would cause an annual
increase of:
a. Five tons per year of lead; or
b. Ten tons per year of any other air contaminant for which the ambient air quality standards have been established;
2. Any application or proposed action requiring a public hearing under the PSD (App. A) of ecology;
3. An order to determine RACT (App. B);
4. An order to establish a compliance schedule or a variance;
5. Establishment or disestablishment of a nonattainment area, or the changing of the boundaries of a nonattainment area;
6. An order to demonstrate the creditable height of a stack (App. A) which exceeds the GEP (App. A) formula height and 213 ft. (App. B) or 65 m (App. B) by the use of a fluid model or a field study. The purpose of the demonstration is to establish emission limitations;
7. An order to authorize a bubble (App. A);
8. A NSR application or order to establish an ERC (App. A);
9. An order which establishes voluntary limits for the potential to emit for a source;
10. An application or action where there is a substantial public interest as determined by the APCO (App. B);
11. When required by federal or state law or regulation;
12. Changes to the SIP (App. B);
13. Substantive changes to regulations;
14. Draft air operating permits;
15. SEPA (App. B) determinations; and/or
16. Additional or special public participation requirements for air operating permit sources as directed by chap. 173-401 WAC, Part IX.
C. EARLY REVIEW. An early review of any action referenced in subsection 2.04B (pg. 2-xx) may be initiated by either the authority or the public by a written request.
1. Purpose. Provides a forum for dialogue at early stages of authority decision making.
2. Methods of Review.
a. Public meetings or workshops;
b. Advisory committees;
c. Peer review groups;
d. Discussion groups; or
e. Public hearings.
D. PUBLIC NOTICE PROCESS. (4.02H) The following is the public notice process:
H. Public Notice.
1. Notice of Construction applications shall be subject to public notice under the following conditions:
a. If otherwise required by state or federal laws or regulations; or
b. If the proposed source would cause an annual increase of ten tons of any air contaminant for which the ambient air quality standards have been established; or
c. If the Yakima County Clean Air Authority determines that such public comment would be appropriate.
2. Within fifteen days of receipt of a complete application for a Notice of Construction the Authority shall determine whether public notice is required, and if so it shall publish notice to the public of an opportunity to submit written comments during a thirty (30) day period. Such public notice shall contain the following information:
a. The name and address of the owner;
b. A brief description of the proposed construction;
c. The location at which a copy of the preliminary determination and a summary of the information considered in making such preliminary determination are available to the public.
1. Public Notice Is Issued.
a. After all information required by the authority is available; and
b. All preliminary determinations are made.
2. Who Pays For Public Notice. The owner or applicant pays the cost of providing public notice.
3. Content.
a. Publication in a Newspaper. Notices are published in a newspaper with a general circulation in the affected area, and they contain:
1) A brief description of the proposal;
2) The location of the documents available for public inspection;
3) The 30 day period for submitting written comments to the authority; and
4) The public hearing dates and locations if hearings are required.
b. Information Available for Public Inspection:
1) Nonconfidential information submitted by the applicant as defined in subsection 1.06D (pg. 1-xx);
2) Applicable preliminary determinations;
3) Analysis of the effects of implementing the proposed action on the ambient air quality;
4) Proposed decision by the APCO (App. B); and
5) Other relevant information.
c. Copies of the Public Notice.
1) Are sent to EPA (App. B) and ecology (App. B), for any application or action.
2) Are sent to the local offices of ecology or other local air authorities if the application or action could effect the ambient air quality in their jurisdictional area.
4. Public Comments.
a. Information for making public comments shall be available at the office of the authority and one public location in the area affected by the proposed action.
b. Public comments are received during the published period.
c. If a public hearing is held, the public comment period will extend through the hearing date and the period specified by the notice.
5. Public Hearings.
a. Interested persons may request a public hearing in writing within the 30 day public comment period.
b. The authority must respond to all requests.
c. The authority decides whether to hold a public hearing.
d. The time and place of the hearing(s) are published in a newspaper with general circulation in the area. The method and content of the notice will comply with subsection 2.04D3a (pg. 2-xx).
6. Response to Public Comment. The authority shall provide a written response to the public comments.
2.05 APPEALS
A. PURPOSE. To define the local policy for appeals of decisions by the APCO (App. B) or board.
B. APPLICABILITY. Any final written decision, order, penalty, fee, permit action, or resolution made by the APCO or board may be appealed.
C. PROCESS.
1. General Direction. The specific details for appeals are in chap 34.04 RCW, chap. 34.05 RCW, chap. 43.21 RCW, chap. 70.94 RCW, WAC 173-400-250, and WAC 173-401-735.
2. Agricultural Odors. See subsection 3.01C3a4) (pg. 3-xx) for an appeal involving agricultural odors.
3. Mutual Settlement. (3.04) Nothing in this article shall
prevent the Control Officer APCO or board from making efforts to
obtain voluntary compliance through warning, conference or any
other appropriate means.
4. Finality. (3.02) Any order issued by the Board or Control Officer shall become final, unless such order is appealed to the Pollution Control Hearings board, as provided in RCW 43.21B.
5. Status During Appeal. (3.03) Any order of the Control Officer or Board shall be stayed pending final determination of any hearing or appeal taken in accordance with the provisions herein, unless after notice and hearing, the Superior Court shall determine that an emergency exists which is of such nature as to require that such order be in effect during the pendency of such hearing or appeal.
3.00 GENERAL RULES
A. PURPOSE. To define rules of a general nature.
B. APPLICABILITY. Applies to the rules in articles 3 and 4.
C. EXEMPTIONS. None.
D. VARIANCES. (7.01 & RCW 70.94.181)
A. Any person who owns or is in control of any plant,
building, structure, establishment, process or equipment, may
apply to the Board for a variance from the provisions of these
Regulations governing the quality, nature, duration or extent of
discharge of air contaminants in accordance with the provisions
of RCW 70.94.181. The application shall be accompanied by such
information and data as the Board may require. The Board may
grant such variance, but only after public hearing or due notice
if the Board finds that:
1. The emissions occurring or proposed to occur do not endanger public health or safety or the environment; and
2. Compliance with the rules and regulations from which variance is sought would produce serious hardship without equal or greater benefits to the public.
3. Provided, however, that the Board will not grant variances to state rules unless the same have been approved by the Washington State Department of Ecology prior to being issued by the Yakima County Clean Air Authority.
4. Total time period for a variance and a renewal of such variance shall not exceed one year.
B. No variance shall be granted pursuant to this section until the Board has considered the relative interest of the applicant, other owners of property likely to be affected by the emissions, and the general public.
C. Any variance or renewal thereof shall be granted within the requirements of subsection A and for time periods and under conditions consistent with the reasons therefore, and within the following limitations:
1. If the variance is granted on the ground that there is no practicable means known or available for the adequate prevention, abatement or control of the pollution involved, it shall be only until the necessary means for prevention, abatement or control become known and available, and subject to the taking of any substitute or alternative measures that the Department of Ecology or Board may prescribe.
1. If the variance is granted on the ground that compliance with the particular requirements or requirement from which variance is sought will require the taking of measures which, because of their extent or cost, must be spread over a considerable period of time, it shall be for a period not to exceed such reasonable time, as in the view of the Department of Ecology or Board is requisite for the taking of the necessary measures. A variance granted on the ground specified herein shall contain a timetable for the taking of action in an expeditious manner and shall be conditioned on adherence to such timetable.
2. If the variance is granted on the ground that it is justified to relieve or prevent hardships of a kind, other than that provided for in Subsections 7.01 (A)(1), (2), and (3), it shall be for not more than one (1) year.
D. If renewal is made to the Board on account of the variance, no renewal thereof shall be granted unless, following a public hearing on the complaint on due notice, the Board finds that renewal is justified. No renewal shall be granted except on application therefor. Any such application shall be made at least sixty (60) days prior to the expiration of the variance. Immediately upon the receipt of the application for renewal the Board shall give public notice of such application in accordance with the rules and regulations of the Board.
E. A variance or renewal shall not be a right of the applicant or holder thereof but shall be granted at the discretion of the Board. However, any applicant adversely affected by the denial or the terms and conditions of the granting of an application for variance or renewal of a variance by the Board, may obtain judicial review thereof under the provisions of Chapter 34.05 of RCW as now or hereafter amended.
F. Nothing in this section and no variance or renewal granted pursuant hereto shall be construed to prevent or limit the applications of the emergency provisions and procedures of RCW 70.94.710 through 70.94.730 to any person or their property.
G. An application for variance or for the renewal thereof submitted to the Department of Ecology or Board pursuant to this section, shall be approved or disapproved by the Board within sixty (60) days of receipt, unless the applicant and the Board agree to a continuance
1. Purpose. To provide a process for obtaining relief from these regulations.
2. Applicability. Any person (App. A) who is subject to these regulations.
3. Requests for Variances or Renewals.
a. General Process.
1) Petitioner submits the written application and documentation to the APCO (App. B);
2) APCO reviews the application and submits it to the board with a recommendation;
3) Board makes a decision or recommendation to ecology.
a) If the requested variance is to an authority rule which is not duplicated in the SIP (App. B) or the WAC (App. B), the decision is made by the board.
b) If the requested variance is to a state rule, the application is referred to ecology (App. B)) with a recommendation, and ecology approves the request. If approved, ecology will send the request to EPA (App. B) with a recommendation for final approval and inclusion in the SIP (App. B) (7.01A3); and
4) The variance is granted by the authority after the final approval.
b. Application. The following information is required in the application:
1) Specific regulation from which relief is requested;
2) Detailed explanation that justifies relief from compliance with the regulation;
3) Plans to bring the source into compliance with the regulation prior to the expiration of the variance;
4) Air pollution source, equipment, and control apparatus (App. A) subject to the variance;
5) Any equipment connected to, serving, or served by the air pollution source, equipment, and control apparatus subject to the variance;
6) Plot plan showing the distance and height of buildings within 200 feet or other distance specified by the APCO from the location of the contaminant source; and
7) Estimated amount that the emissions will exceed standards as a result of the variance.
c. Additional Documentation.
1) Any additional information required by the APCO.
2) Any information volunteered by the petitioner.
d. Review Criteria. (7.01B) Before granting a variance, the board must consider the interests of:
1) The applicant;
2) Owners of adjacent property likely to be affected by the variance; and
3) The general public.
e. Review Period. (7.01 G) Any application for variance or renewal must be approved or disapproved by the board within 60 days of receipt unless the applicant and the board agree to a continuance.
f. Public Involvement. Shall be done as required in section 2.04 (pg. 2-xx).
4. Conditions for Granting a Variance. (7.01A1&2)
a. The emissions proposed do not endanger public health, safety, or the environment;
b. The emissions from the source proposing the variance either singularly or in combination with other sources in the vicinity will not cause a violation of a NAAQS (App. B) or a PSD (App. B) increment; and
c. Compliance with the rules or regulations without a variance would produce serious hardship without equal or greater public benefits.
5. Limitations for Granting a Variance or Renewal. (7.01C)
a. No Practicable Technology Available.
1) Adequate prevention, abatement or control of the pollution is not available;
2) The variance is granted only until the necessary technology for prevention, abatement or control becomes available.
3) When the control technology becomes reasonably available;
a) The variance may be rescinded; and
b) Ecology or the board may prescribe alternate measures.
b. Compliance with Requirements will be Difficult.
1) Will require taking measures which are extensive or costly;
2) Must be accomplished over a long time period;
3) The variance must be granted for a reasonable time to complete the required measures;
4) The variance must contain a schedule for completing the measures in a timely manner; and
5) Must include conditions requiring adherence to the schedule.
6. Expiration. (7.01A4) Variances and renewals shall expire one year or less after the issuance, or sooner if;
a. The conditions of the variance or renewal are fulfilled; or
b. Replaced by a new law or regulation.
7. Renewals (7.01D & RCW 70.94.181(1)) Any variance may be renewed for the same terms, conditions, and period as when the variance was granted up to one year from the initial issuance of the variance.
a. Application for Renewal. (7.01D) Must be submitted at least 60 days prior to the expiration of the variance. Immediately upon the receipt of the application the board must give public notice of the application.
b. The process for the renewal will follow subsection 3.00E3 (pg. 3-xx).
c. Renewals After Complaints Concerning Variances. (7.01D & RCW 70.94.181(1)) If ecology or the board receives a complaint about the variance, a renewal must not be granted until the board issues a notice and holds a public hearing on the complaint. Based upon results of the public hearing, the board will grant a renewal if it finds the renewal is justified.
d. Applications for renewals beyond one year must apply for a new variance.
8. Judicial Review. (7.01 E) A variance or its renewal is not the right of the applicant or holder, but is granted at the discretion of the board. Any applicant who is adversely affected by the denial or the conditions of a variance or its renewal may obtain judicial review under the provisions of Chap. 34.05 of RCW.
9. Emergency Provisions. (7.01F) Nothing in this section or any variance or renewal granted under this section is construed to limit the applications of the emergency provisions and procedures of air pollution episodes as described in WCAA (App. B).
E. OPERATION AND MAINTENANCE.
1. Purpose. To define operation and maintenance standards for all process and control apparatus (App. A) to prevent avoidable emissions.
2. Applicability. Any person or emission unit which is subject to these regulations.
3. Exemption. Process or control apparatus which is out of service.
4. Requirement. The owner or operator of an air pollution source shall:
a. Operate and maintain all process and control apparatus, which has the potential to allow emissions, according to the specifications and recommendations of the manufacturer;
b. Maintain this equipment in good repair and working condition;
c. Operate this equipment to minimize emissions; and
d. Keep a current copy of the manufacturer's manuals and specifications on the site and available for inspection by the APCO (App. B).
3.01 EMISSION STANDARDS
A. PURPOSE. To control and prevent air pollution.
B. APPLICABILITY. (5.06) To all sources and emissions units.
are required to meet the emission standards of this chapter.
Where When multiple an emission standards listed exist, in
another chapter is applicable to a specific emissions unit, such
all applicable standards will apply. take precedent over a
general emission standard listed in this chapter.
C. GENERAL EMISSION STANDARDS FOR MAXIMUM PERMISSIBLE EMISSIONS. All
sources are required to comply with the general emission
standards. The measurable emission standards cited in this
section are listed in app. D with the test methods and compliance
assurance requirements. Exemptions are listed in subsection
3.01C3 (pg. 3-xx).
1. Prohibitions. (5.06)
a. Visible Emissions. (5.06, 5.07A, & 5.09B) No person shall
cause or permit visible emissions (App. A) plume from any
emissions unit that exceeds twenty percent (20%) opacity for
three minutes in any one hour period except:
1) (5.06A1 & 5.09B1) When the emissions occur due to soot
blowing/and grate cleaning from hog fuel boilers, and the
operator can demonstrate that the emissions will not exceed
twenty percent (20%) opacity (App. A) for more than fifteen (15)
minutes in any eight (8) consecutive hours. The intent of this
provision is to permit allow the soot blowing and grate cleaning
necessary to the operation of boiler facilities. This practice,
except for testing and trouble shooting, is to be scheduled for
the same approximate times each day, and the authority must be
advised of the schedule.
2) (5.06A2) When the owner or operator of the source
supplies valid data to show that the opacity exceeds twenty
percent (20%) as the result of only uncombined water the presence
of condensed water droplets, as determined by a certified opacity
reader. The concentration of particulate matter as shown by a
source test approved by the Authority must be less than one-tenth
(0.1) grains per dry standard cubic foot. For combustion
emissions the exhaust gas volume shall be corrected to seven
percent (7%) oxygen.
3) When two or more sources are connected to a common stack (App. A), the authority may allow or require the use of an alternate time period if it is more representative of normal operations.
4) When an alternate opacity limit has been established as authorized by WCAA (App. B).
5) (5.06A3) As provided for in WAC 173-433-110 "Opacity
Standards For Solid Fuel Burning Devices". The opacity standard
for wood heaters is in subsection 3.04E1(a) (pg. 3-xx).
b. Particulate Matter.
1) Preventing Particulate Matter from becoming airborne.
(5.06B). No person shall cause or allow permit the emission of
particulate matter PM (App. A) from any source which is
transported or becomes deposited beyond the source property under
direct control of the owner or operator of the source in
sufficient quantity to interfere unreasonably with the use or and
enjoyment of another the property upon which the material was
transported or deposited.
2) (5.12A) No person shall cause or , let, allow, permit or
suffer particulate matter PM to be stored, handled, or
transported without taking reasonable precautions to prevent the
release of air pollutants.
c. Reasonable Precautions. (5.12B) No person shall cause or,
let, allow, permit, or suffer a building or its appurtenances or
road to be constructed, altered, repaired or demolished without
taking reasonable precautions to prevent the release of air
pollutants.
d. Odors. (5.06D) Any person who shall causes or allows the
generation of any odor from any source which may unreasonably
interfere with an the adjoining property owner's use or and
enjoyment of another his property must use recognized good
practice and procedure to reduce these odors to a reasonable
minimum.
e. Air contaminants or water vapor Detrimental Emissions. to
persons or property. (5.06 E) No person shall cause or allow an
permit the emission of any air contaminant or water vapor from
any source, including any air contaminant whose emission is not
otherwise prohibited by this Regulation, if the air contaminant
or water vapor causes detrimental to the health, safety, or
welfare of any person; or causes damage to the property or
business of another person.
f. Sulfur Dioxide (SO2) (App. B) (5.06 F)
1) (5.06 F1) No person shall cause or permit the emission of
a gas containing sulfur dioxide SO2 in excess of 1,000 parts per
million (ppm). (App. B).
2) (5.06 F2) All concentrations of sulfur dioxide SO2
referred to above are by volume, dry standard conditions (App.
A). and For combustion emissions the exhaust gas volume shall be
corrected to seven percent (7%) oxygen O2 (App. B) and based on
the average of any period of sixty 60 consecutive minutes.
3) When the owner or operator of a source emitting SO2 supplies emission data and demonstrates there is no feasible method of reducing the concentration to < 1,000 ppm and the state and federal ambient air quality standards for SO2 will not be exceeded, the authority may require:
a) Specific ambient air monitoring stations to be established, operated, and maintained by owner or operator at mutually approved locations;
b) The sampling results shall be available upon request; and
c) A monthly summary shall be submitted to the authority.
g. Concealment and Masking. (5.06G) No person shall cause or
permit the installation or use of any device, or the use of any
means which, without resulting in a reduction in the total amount
of air contaminant emitted, conceals an emission of an air
contaminant pollutant which would otherwise violate any
requirements provisions of this regulation chapter.
h. Sale or Installation of Air Pollution Source. (5.06I) No
person shall hereafter sell or install within the jurisdiction of
the Yakima County Clean Air Authority any continuous, stationary
an air contaminant pollution source in which the air contaminant
emitted therefrom cannot be restricted to not capable of meeting
the standards of this regulation as set forth in Sections 5.06(A)
and 5.08.
2. Requirements.
a. Two or More Emission Units. (5.06) When two or more
emissions units are connected to a common stack, and the operator
elects not to provide the means or facilities to sample emissions
from the individual emissions units, and the relative
contributions of the individual emissions units to the common
discharge are not readily distinguishable, then the emissions of
the common stack must meet the most restrictive standard of any
of the connected emissions units.
b. Reasonably Available Control Technology (RACT) (App. A).
(5.06, 5.09B2, & 5.09H) Further, All emissions sources and units
are required to use reasonably available control technology
(RACT).
3) This which may be determined for some sources or source
categories to be more stringent than the applicable emission
limitations of any chapter of Title 173 WAC.
4) Where current controls are determined to be less than
RACT, the authority shall, on a case-by-case basis, define RACT
for each source or source category and issue a regulatory order
to the source or sources for installation of RACT.
c. Fugitive Dust Sources. (5.06H) No person shall cause or
permit material handling without taking reasonable precautions to
prevent the release of contaminants to the ambient air. (5.06C)
1) (5.06H1) The owner or operator of a source of fugitive
dust must shall take reasonable precautions to prevent fugitive
dust from becoming airborne and shall maintain and operate the
source to minimize emissions.
2) (5.06 H. 2) The owner(s) or operator(s) of any existing a
source(s) of fugitive dust that has been identified as a
significant contributor to a Category I PM10 or PM2.5 nonattainment
area, shall be required to must use reasonably available control
technology RACT to control emissions. Significance will be
determined by the definition found in 40 CFR Part 51, Appendix S,
as amended July 1, 1990 subsection 4.02G2g (pg. 4-xx) and table
4.02-2 (pg. 4-xx).
3) Specific dust control requirements are in section 3.08 (pg. 3-xx).
d. Opacity Measurement. (5.06J) The density or opacity of an
air contaminant shall emission must be measured at the point of
its emission. except When the point of emission cannot be readily
observed it may be measured at an observable point on a plume
nearest the point of emission.
e. Maintenance and Operation. As required in subsection 3.00E (pg. 3-xx).
f. Compliance Testing. As required in subsection 3.11E2 (pg. 3-xx).
g. Inspection. As authorized in subsection 5.00C (pg. 5-xx).
h. Permitting. Owners or operators of sources may be required to obtain permits from the authority under sections 4.04 (pg. 4-xx) or 4.05 (pg. 4-xx).
3. Exemptions.
a. Odors Caused by Agricultural Activities (App. A) Using Good Agricultural Practices (App. A) (RCW 70.94.640).
1) These odors are exempted from this regulation unless there is a substantial adverse effect on public health.
2) In determining good agricultural practices the authority shall consult with a recognized third-party expert prior to issuing a NOV (App. B).
3) A NOV issued under this subsection shall include a statement that the activity:
a) Is inconsistent with good agricultural practices; or
b) Has odors that have a substantial adverse impact on public health.
4) In an appeal to the pollution control hearings board or superior court, the authority shall prove the activity:
a) Is inconsistent with good agricultural practices; or
b) Has odors that have a substantial adverse impact on public health.
5) When a parcel of land is sold from contiguous agricultural land for residential purposes, this exemption does not apply.
b. NH3 (App. B) Emissions from Fertilizer. (RCW 70.94.645) NH3 emissions from the storage, distribution, transport, or application of a NH3 fertilizer for agricultural or silvicultural uses are exempted from regulation.
D. MINIMUM ADDITIONAL EMISSION STANDARDS FOR COMBUSTION AND INCINERATION
SOURCES (App. A) (5.07) These standards are in addition to the
general standard in subsection 3.01C (pg. 3-xx).
1. Particulate Matter.
a. Sources Burning Wood Derived Fuels. (5.09B1) The emission of PM from a unit combusting wood derived fuels for the production of steam must not exceed 0.46 gram per dscm (App. B) (0.2 grain per dscf (App. B)).
b. All Other Sources. The emission of PM must not exceed 0.23 gram per dscm (0.1 grain per dscf).
c. Measurement. The concentration of PM will be measured as specified in app. D (pg. D-xx)
2. Incineration Sources. (App. A)
3. Total Unburned Hydrocarbons Volatile Organic Compounds
(VOCs). (5.07B) For all Incinerator sources, no person shall
cause or permit emissions in excess of 100 ppm. This of total
unburned hydrocarbons as must be measured by as specified in app.
D (pg. D-2).
a. Hours of Operation. (5.07B) Incinerators shall will be
operated only during daylight hours (App. A) unless written
permission to operate at other times is obtained received from
the authority.
b. Large Incinerators. (5.07D) All incinerators designed to
burn twelve tons per day of materials shall be are subject to the
standards set forth in chap. 173-434 WAC if they are:
1) Designed to burn ≥(App. B) 12 tons per day of materials; and
2) Constructed after January 1, 1985.
E. MINIMUM EMISSION ADDITIONAL STANDARDS FOR GENERAL PROCESS SOURCES.
(App. A)
1. These standards are in addition to the general standard in subsection 3.01C (pg. 3-xx).
2. (5.07E & 5.08) No person shall cause or permit emissions
in excess of Section 5.08. General Process Units are required to
meet all applicable provisions of Section 5.06. No person shall
cause or permit the emissions of particulate matter from any
general process operation in excess of one tenth (0.10) grains
per standard cubic foot of dry exhaust gas as tested by: The
emission standard and test for PM will be measured as specified
in app. D (pg. D-2).
F. MINIMUM EMISSION ADDITIONAL STANDARDS OR PROCEDURES FOR CERTAIN SOURCE
Categories (5.09 & WAC 173-400-070) The authority finds that
reasonable regulation of sources within certain categories
requires separate standards applicable to such categories. The
standards set forth in this section shall be the minimum
allowable standards for sources within the categories listed. and
Except as specifically provided in this Section, such sources
shall be required to meet the provisions of Section 5.06, Section
5.07., and Section 5.08. These standards are in addition to the
standards in subsection 3.01C, D, or E (pgs. 3-xx to yy).
1. Hogged Fuel Boilers. (5.09B)
(5.09 B1) No person shall operate a hogged fuel boiler that
will cause or permit an emission for more than three (3) minutes
in any one (1) hour of an air contaminant from any source which,
at the emission point or within a reasonable distance of the
emission point, exceeds twenty percent (20%) opacity or which
causes an emission of particulate matter in excess of one-fifth
(0.20) grains per standard dry cubic foot. Particulate matter
emissions shall be measured by EPA Method 5 or approved
procedures contained in "Source Test Manual Procedure for
Compliance Testing", State of Washington Department of Ecology on
file at the Authority or Ecology. Provided that emissions may
exceed twenty percent opacity (20%) for up to fifteen (15)
consecutive minutes once in any eight (8) hours. The intent of
this provision is to permit the soot blowing and grate cleaning
necessary to the operation of these units. This practice is to
be scheduled for the same specific times each day and the
authority shall be notified of the schedule or any changes.
(5.09B2) All hogged fuel boilers shall utilize Reasonably
Available Control Technology and shall be maintained and operated
to minimize emissions.
(5.09B3) The visible and particulate emission standards and
tests are in app. D. The authority may establish additional
requirements for hogged fuel boilers located in or proposed for
location in sensitive areas which can be implemented through
permitting or enforcement actions. These additional requirements
may include, but shall not be limited to:
a. (5.09B3a) A requirement to meet additional provisions of
subsection 5.07 3.01D (pg. 3-xx);
b. (5.09B3b) A requirement to utilize Best Available Control
Technology BACT (App. B); or
c. (5.09B3c) A requirement to reduce or eliminate emissions
if the authority establishes that such emissions unreasonably
interfere with the use or enjoyment of the property of others or
if such reductions or eliminations are necessary to meet ambient
air quality standards.
2. Orchard Heating.
a. (5.09C&C1) Burning of rubber materials, asphaltic
products, crankcase oil or petroleum wastes, plastic, or garbage
is prohibited; and
b. (5.09C2) It shall be is unlawful to burn any material or
operate any orchard heating device that causes visible emissions
exceeding twenty percent (20%) opacity, except during the first
thirty (30) minutes after such device or material is ignited.
The visible emission standard and test is in app. D (pg. D-1).
3. Grain Elevators. (5.09 D2) The authority may establish
additional requirements for grain elevators. These requirements
may include, but shall not be limited to a requirement to meet
the provisions of Section 5.06 and Section 5.08 standards of
subsection 3.01E. (5.09D1) Any grain elevator which is primarily
classified as a materials handling operation shall meet all the
provisions of Section 5.06, B, C, D, and E.
4. Catalytic Cracking Units. (5.09G)
a. Existing Units. (5.09G1) All existing catalytic cracking
units shall meet all provisions of Sections 5.06 (B), (C), (D),
(E) and (G) and:
1) No person shall cause or permit the emission for more
than three (3) minutes, in any one hour, of an air contaminant
from any catalytic cracking unit which at the emission point, or
within a reasonable distance of the emission point, exceeds forty
percent opacity. The visible emission standard is in app. D (pg.
D-2).
2) No person shall cause or permit the emission of
particulate material in excess of 0.46 grams per dry cubic meter
of standard conditions (0.20 grains dscf) of exhaust gas. The PM
emission standard is in app. D (pg. D-2).
b. All New Catalytic Cracking Units. (5.09G2) shall meet all
provisions of WAC 173-400-115. The maximum visible emission is
the opacity standard in subsection 3.01C1a (pg. 3-xx) and app. D
(pg. D-2) or a lower standard established during a NSR (App. B).
5. Sulfuric Acid Plants (H2SO4). No person will cause to be discharged into the atmosphere from a H2SO4 plant, any gases which contain acid mist, expressed as H2SO4, in excess of 0.15 pounds per ton of acid produced. Sulfuric acid production shall be expressed as 100% H2SO4.
6. Sewage Sludge Incinerators. See subsection 2.03B (pg. 2-xx) for the standards.
7. Asbestos. (5.09E) No person shall remove or otherwise
disturb asbestos, to the extent that asbestos fibers may become
airborne, without notifying the Authority ten (10) business days
prior to removal. If removal is necessary due to an emergency,
the ten day waiting period may be waived by the Authority.
1. Private Residents.
Private homeowners, when removing friable asbestos materials from their normally occupied or will be normally occupied homes, may be required to remove the asbestos materials according to the National Emission Standard for Hazardous Air Pollutants (NESHAPS) as set forth in Title 40 Code of Federal Regulations part 61, as the same now exists or may be amended. Removal and disposal of non-friable asbestos materials shall be conducted in accordance with practices and procedures approved by the Authority.
2. Small Quantity Asbestos Material.
Asbestos Materials in quantities less than 160 square feet or 260 linear feet must be removed and disposed of according to practices and procedures approved by the Authority.
3. Commercial, Industrial or other sources.
No person shall demolish any commercial, institutional, or industrial building, or any residential facility constructed to house four (4) or more families without first performing a thorough inspection, to be conducted by a qualified expert to determine the quantities and types of asbestos materials present. If it is determined that such building contains asbestos, no person shall commence the demolition of such facility without complying with the requirements of NESHAPS, the Federal Rule stated in E (1) above.
4. Fees or Administrative Charges.
Fees associated with this subsection (5.09(E)) shall be in accordance with Article XIII, Section 13.04 of this regulation.
8. Wigwam Burners. (5.09F)
a. All wigwam burners shall meet all provisions of Section
5.06 (B), (C), (D), (E), (F) and (G).
b. All wigwam burners shall use RACT. All emissions units shall be operated and maintained to minimize emissions. These requirements may include a controlled tangential vent over fire air system, an adequate under fire system, elimination of all unnecessary openings, a controlled feed and other modifications determined necessary by Ecology or the Authority.
c. It shall be unlawful to install or increase the existing use of any burner that does not meet all requirements for new sources including those requirements specified in Section 5.06 and Section 5.07, except operating hours.
d. Ecology may establish additional requirements for wigwam burners located in sensitive areas as defined by chapter 173-440 WAC. These requirements may include but shall not be limited to:
i. A requirement to meet all provisions of in Section 5.06 and Section 5.07. Wigwam burners will be considered to be in compliance if they meet the requirements contained in Section 5.06(A). An exception is made for a startup period not to exceed thirty (30) minutes in any eight (8) consecutive hours.
ii. A requirement to apply BACT.
iii. A requirement to reduce or eliminate emissions if Ecology establishes that such emissions unreasonably interfere with the use and enjoyment of the property of others or are a cause of violation of ambient air standards.
9. Asphalt Batch Plants. (5.09 A)
a. All batch plants shall meet all requirements of Title 40 CFR 60.90 Subpart I, "Standards of Performance for Hot Mix Asphalt Facilities".
b. Asphalt batch plants shall utilize Best Available Control Technology and shall be maintained and operated to minimize emissions
10. Other Wood Waste Burners. (509H) Wood waste burners not specifically provided for in this section shall meet all provision of Section 5.06. Such wood waste burners shall utilize RACT and shall be operated and maintained to minimize emissions.
3.02 STANDARDS FOR SOURCES OF HAZARDOUS AIR POLLUTANTS. (WAC 173-400-075 & Chap. 173-460 WAC) (New Section)
A. PURPOSE. To control and prevent emissions of hazardous air pollutants.
B. APPLICABILITY. Applies to the owners or operators of any stationary source subject to the requirements of 40 CFR Parts 61 and 63.
C. REFERENCES.
1. Subsection 2.03B references 40 CFR Parts 61 and 63 and WAC 173-400-075 as applicable.
2. Hazardous air pollutants (HAP) are listed in app. L.
3. Toxic air pollutants (TAP) are listed in app. K, para. B.
D. EMISSION STANDARDS FOR PERCHLOROETHYLENE (PCE) DRY CLEANERS. (WAC 173-400-075(6))
1. Purpose. To define specific standards for dry cleaners using the solvent PCE (App. B) which supplement 40 CFR Part 63, Subpart M, National Perchloroethylene Emission Standards for Dry Cleaning Facilities.
2. Applicability. Any dry cleaning operations that uses PCE.
3. Requirements. The quantity of PCE used annually determines the source category, venting, and leak inspection frequency requirements.
a. Source Categories. Are shown in tables 3.02-1.
Table 3.02-1 PCE Dry Cleaner Source Categories
Applicability | Small Area Sources (a) |
Large Area Sources (b) |
Major Area Sources (c) |
Dry cleaning Facilities with |
Purchasing less than | Purchasing between: | Purchasing more than |
(1) Only Dry-to-Dry Machines | 140 gallons PCE/yr | 140-2,100 gallons PCE/yr | 2,100 gallons PCE/yr |
(2) Only Transfer Machines | 200 gallons PCE/yr | 200-1,800 gallons PCE/yr | 1,800 gallons PCE/yr |
(3) Both Dry-to-Dry & Transfer Machines | 140 gallons PCE/yr | 140-1,800 gallons PCE/yr | 1,800 gallons PCE/yr |
c. Venting and Leak Inspection. The requirements are shown in table 3.02-2. During the inspection the systems must be operating. An inspection must include an examination of the following system components:
1) Hose and pipe connections, fittings, couplings, and valves;
2) Door gaskets and seatings;
3) Filter gaskets and seatings;
4) Pumps;
5) Solvent tanks and containers;
6) Water separators;
7) Muck cookers;
8) Stills;
9) Exhaust dampers;
10) Diverter valves; and
11) Cartridge filter housings.
Table 3.02-2 PCE Dry Cleaner Venting and Leak Inspection Requirements.
Requirement | Small Area Sources (a) |
Large Area Sources (b) |
Major Area Sources (c) |
Air-PCE Vapor Venting System | |||
(1) Installed on or before Sept. 21, 1993. | No requirement | Through a refrigerated condenser. | Through a refrigerated condenser. |
(2) Installed after Sept. 21, 1993. | Thru a refrigerated condenser. | Through a refrigerated condenser. | Through a refrigerated condenser followed by a small carbon adsorber. |
(3) PCE Leak Inspection Frequency | Every other week. | Weekly | Weekly |
e. Operation and Maintenance.
1) As required by subsection 3.00E (pg. 3-xx); and
2) Close the door of each dry cleaning machine except when transferring articles to or from the machine.
f. Leak Repair.
1) Leaks must be repaired within 24 hours of detection unless repair parts can not be ordered;
2) Repair parts must be ordered within two working days of detecting the leak; and
3) Repair parts must be installed within 5 working days after receiving them.
g. Storage of PCE.
1) Store all PCE and wastes containing PCE in a closed container; and
2) Drain cartridge filters in the housing or other sealed container for at least 24 hours before discarding the cartridges.
h. Recordkeeping Requirements. The following requirements are in addition to the requirements in section 3.11 (pg. 3-xx). Documents and records must be kept on-site at the dry cleaning facility for at least:
1) As long as the PCE dry cleaning and process vent or control systems are in operation:
a) Design specifications and operating manuals;
b) Maintenance plans;
c) Design specifications and operating manuals for any modifications to these systems.
2) Five years after the close of the business year.
a) A record of dates and results of all monitoring, inspections, and repairs of the PCE dry cleaning system.
b) A record of the amount of PCE purchased each month including the receipts for the PCE purchases.
c) A record of the amount of PCE used for each machine during the previous 12 months.
d) A record of the total weight of articles cleaned for each machine during the same 12 month period used in subsection 3.02D3h (2)(c) (pg. 3-xx).
e) If a refrigerated condenser is used on a dry-to-dry machine, dryer, or reclaimer, a weekly record of the air temperatures measured at the outlet of the refrigerated condenser during the cool-down period to verify compliance with subsection 3.02D3i (pg. 3-xx).
f) If a refrigerated condenser is used on a washer, a weekly record of the differences between the air temperatures measured at the inlet and outlet of the refrigerated condenser to verify compliance with subsection 3.02D3i (pg. 3-xx).
g) If a carbon adsorber is used on a dry cleaning system, a weekly record of measuring the concentration of outlet PCE to verify compliance with subsection 3.02D3j (pg. 3-xx).
i. Requirements for Refrigerated Condensers.
1) Have temperature sensors permanently installed prior to September 23, 1996, if the PCE dry cleaning system was built prior to December 9, 1991;
2) Have permanently installed temperature sensors that have a working range between 32°F and 120°F (App. B) (0°C and 49°C (App. B)), can be seen at all times, and be accurate to within 2° F or 1.1°C.
3) Have an air temperature at the outlet of the refrigerated condenser installed on a dry-to-dry machine, dryer or reclaimer ≤ 45°F (7°C) during the cool-down period;
4) Have a difference in the air temperatures between the inlet and outlet of a refrigerated condenser installed on a washer ≥ 20°F (11°C).
5) Provide a valving system which prevents air drawn into the dry cleaning machine from passing through the refrigerated condenser when the door of the machines is open; and
6) Must not release the air-PCE-vapor stream into the atmosphere while the dry cleaning machine drum is rotating or, if installed on a washer, until the washer door is opened.
j. Requirements for Carbon Adsorbers. Must meet all of the following requirements:
1) Have PCE measurements at the exhaust of the carbon adsorber ≤ 100 ppm (App. B); and
2) Weekly measure and record the concentration of PCE at the outlet of the carbon adsorber using a colorimetric detector tube that is accurate to within 25 ppm.
3) Begun monitoring temperature sensors by September 23, 1996, if the PCE dry cleaning system was installed prior to December 9, 1991.
4. Additional Requirements for Major Area Sources.
a. If a dry cleaning system is located at a source which emits 10 tons or more of PCE annually, the source must meet additional requirements in 40 CFR Part 63, Subpart M; and
b. Must comply with sections 4.04 (pg. 4-xx) or 4.05 (pg. 4-xx).
5. A new source must continue to use BACT (App. B) after the requirements of subsection 4.02G2 (pg. 4-xx) are met.
SECTION 5.01 - 3.03 OUTDOOR BURNING AND AGRICULTURAL BURNING
Outdoor burning in Yakima County shall, unless specifically
exempted in Section 5.03(D), be conducted only by permit issued
by the local responsible jurisdiction and shall be subject to the
limitations set forth herein.
A. The issuance of outdoor burning permits for the following activities shall be governed by the Authority, local city, town or fire protection district in which such fire or fires are being conducted.
1. Residential Burning;
2. Outdoor burning of less than 500 tons of residue of natural character such as trees, stumps, shrubbery or other natural vegetation arising from land clearing projects.
3. Agricultural burning as defined in WAC 173-430-030.
B. The issuance of permits for the following outdoor burning shall be governed by the Washington State Department of Natural Resources or by federal authorities for lands under federal control:
1. Abating of forest fire hazard;
2. Prevention of fire hazard;
3. Instruction of public officials in the method of forest fire fighting;
4. Any silviculture operation to improve the forest lands of the state;
5. All silvicultural burning used to promote regeneration of rare and endangered plants found within natural area preserves, as identified under Chapter 79.70 RCW or used to maintain fire dependent ecosystems for rare plants or animals within the state, federal and private natural park area preserves, natural resource conservation areas, parks and other wildlife areas.
C. Except as set forth in subsection 5.03(D) hereof, all other outdoor burning will be governed by permits issued by the Yakima County Clean Air Authority.
D. Except as set forth in subsection 5.03(D) hereof, it is a violation of these Regulations for any person to conduct outdoor burning without obtaining a permit from the responsible jurisdiction as set forth above.
E. Any person requesting a permit from a local responsible jurisdiction, such as local city, town, fire protection district, conservation district or the Authority, for an outdoor burning permit shall pay a fee as governed by the fee schedule of that agency then in effect. The fee schedule in effect for the Yakima County Clean Air Authority is as shown in Article XIII, Section 13.03 of this regulation.
SECTION 5.02 - REGULATIONS APPLICABLE TO ALL OUTDOOR BURNING
A. The Regulations in this Section are applicable to all outdoor burning whether conducted under the jurisdiction of the Yakima County Clean Air Authority, local cities, towns, fire protection districts or conservation districts, or the Department of Natural Resources.
1. It shall be unlawful for any person to ignite, cause or permit to be ignited or to suffer, allow or maintain any outdoor burning within the jurisdiction of any of the above authorities as provided in Section 5.01 and in addition thereto, it shall be unlawful and not within any of the exemptions of subsection 5.03(D) and Section 5.04 for any person to ignite, cause or permit or suffer to be ignited or allow or maintaining any outdoor burning within any of the jurisdictions described above as follows:
a. Containing garbage, dead animals, asphalt, petroleum products, paints, rubber products, plastics, paper (other than what is necessary to start a fire), cardboard, treated wood, construction debris, metal, or any substance other than natural vegetation that normally emits dense smoke or obnoxious odors.
b. During any forecast, alert, warning or emergency condition as defined in RCW 70.94.715.
c. During any impaired air quality condition as defined in RCW 70.94.473.
B. It shall be prima facie evidence that the person who owns or controls property on which outdoor burning occurs has allowed or caused such open fire.
SECTION 5.03 - REGULATIONS APPLICABLE TO ALL OUTDOOR BURNING WITHIN THE JURISDICTION OF THE YAKIMA COUNTY CLEAN AIR AUTHORITY, LOCAL CITIES, TOWNS, FIRE PROTECTION DISTRICTS AND CONSERVATION DISTRICTS
A. The Yakima County Clean Air Authority finds that it is consistent with its policy of reducing outdoor burning to the greatest extent possible to prohibit outdoor burning in certain areas subject to the exceptions as set forth in subsection 5.03(D) hereof.
B. Except as set forth in subsection 5.03(D) hereof, no outdoor burning shall be allowed in any area of Yakima County, Washington which exceeds federal or state ambient air quality standards for pollutants emitted by outdoor burning which includes the Yakima Urban Area and the city limits of the city of Selah, Washington.
C. Except as provided in subsection 5.03(D) hereof, outdoor burning shall not be allowed in any urban growth area as defined in RCW 36.70(a).030 and RCW 36.70(a).110, or in any city in the Authority's jurisdiction having a population greater than 10,000 persons if:
1. Such areas threaten to exceed state or federal air quality standards, and;
2. Alternative disposal practices consisting of a good solid
waste management plan are reasonably available or practices
eliminating production of organic refuse are reasonably
available.
D. Outdoor burning shall be allowed without permit for:
1. Small outdoor fires on an occasional basis for ceremonial, religious, or cooking purposes or like social purposes;
2. Fires from barbecues, flares, torches, gas burners, incense burners and insect pots.
3. Structure fires for instruction in methods of fire fighting, conducted by fire districts or city fire department or any government controlled fire fighting agency, and outside any urban growth area as defined in RCW 36.70(a).030 and RCW 36.70(a).110, if all of the following conditions are met:
a. The fire conforms with any other permits, licenses, or approvals that are required;
b. The fire is not located in an area that is declared to be in an air pollution episode or any state of an impaired air quality as defined in RCW 70.,94.715 and 70.94.473;
c. Nuisance laws are applicable to the fire, including nuisances related to the unreasonable interference with the enjoyment of life and property and the depositing of particulate matter or ash on other property;
d. Notice of the fire is provided to the owners of property adjoining the property where the fire will occur, to the persons who potentially will be impacted by the fire;
e. Each structure that is proposed to be set on fire must be identified specifically as a structure to be set on fire. Each other structure on the same parcel of property that is not proposed to be set on fire must be identified specifically as a structure that is not proposed to be set on fire; and
f. Before setting a structure on fire, a good faith inspection is conducted to determine if materials containing asbestos are present, the inspection is documented in writing and forwarded to the Authority, and asbestos that is found is removed prior to the burning.
SECTION 5.04 - REGULATIONS APPLICABLE TO PERMITS ISSUED BY THE YAKIMA COUNTY CLEAN AIR AUTHORITY FOR ALL OTHER OUTDOOR BURNING
A. Outdoor burning permits will be issued by the Yakima County Clean Air Authority pursuant to restrictions and limitations on outdoor burning as set forth in these Regulations as follows:
1. Except as set forth in Section 5.03(D) hereof, agricultural burning to control diseases and insects or developments of physiological conditions conducive to increase crop yield.
a. All applications for permits to set fire for such agricultural burning shall be acted upon by the Authority within seven (7) days from the date such application is filed.
b. When burning is necessary to control disease or insect infestation and alternative methods are not available and the Yakima County Agricultural Extension Agency so certifies.
2. Except as set forth in Section 5.03(D) hereof, instruction in methods of fire fighting conducted by fire districts or city fire departments or any government controlled fire fighting agency.
B. Permits issued for burning under this Section shall be drafted to minimize emissions, including denial of permission to burn during periods of adverse meteorological conditions.
C. All permits issued by the Authority will contain conditions to insure that public interest in air, water and land pollution and safety to life and property is fully considered and will be designed to minimize air pollution as practicable.
D. All applications for permits must demonstrate that the setting of fires as requested is the most reasonable procedure to follow in safeguarding life and property and no other reasonable alternative (as defined in the WAC 173-425) is available to successfully carry out the enterprise in which the applicant is engaged.
SECTION 5.05 - ADDITIONAL RESTRICTIONS ON OUTDOOR BURNING
All outdoor burning conducted pursuant to this Regulation shall be conducted between the hours of sunrise and sunset, except that burning for pest or disease control or for land clearing purposes, and of which the combustible material consists primarily of wood more than twelve (12) inches in diameter, may be conducted after sunset, but such fires shall not be ignited or fed after 12:00 noon on any day they are ignited. For the purpose of this provision a fire shall be deemed to be out and extinguished when there is not a visible flame coming from the fire.
A. No open burning shall be conducted when the Control Officer, acting on guidelines for air quality control which are hereafter established by the Board, has prohibited such burning by a curtailment call or Ecology has declared an Air Pollution Episode.
1. Any person or entity responsible for an open fire shall immediately proceed to extinguish such fire to prevent visible smoke when notified of the existence of an air pollution episode by any of the means set forth hereafter. Notice will be deemed sufficient to the public for all purposes of these Regulations after three (3) hours have elapsed from the time such notice has been delivered to and published by a newspaper of general circulation in the area where such limitation applies, or has been delivered to and broadcasted by a radio or television station serving the area, for a small fire and ten (10) hours for the remaining fires.
B. Any person responsible for fires set in accordance with this Section must abide by all rules and procedures set by other agencies having any jurisdiction over the practice of open burning.
A. PURPOSE. To reduce and control outdoor and agricultural burning (App. A) and the resulting air pollution. (Chaps. 173-425 & 173-430 WAC
B. APPLICABILITY. (5.01B) Applies to all outdoor and agricultural burning on private, county, state, and federal land unless exempted or another public agency has an effective program in place for the control of outdoor and agricultural burning, and the program has been delegated in accordance with subsection 3.03I (pg. 3-xx).
1. This section applies to burning requiring a written permit, a general rule permit, or exempted from permitting.
2. The agricultural burning portions of this section apply only to agricultural operations (App. A) and government agencies with burning requirements related to agriculture.
3. Fire fighting training fires are a type of outdoor burning, and subsections 3.03C (pg. 3-xx) and 3.03D (pg. 3-xx) are applicable unless modified or granted a limited exemption in another subsection.
4. This section is not applicable to fire training at enclosed fire training facilities that are permitted under section 4.02 (pg. 4-xx).
5. This section does not apply to silvicultural burning (App. A) which is regulated by WCAA (App. B), chap. 332-24 WAC, and the Washington state smoke management plan.
C. GENERAL PROVISIONS FOR ALL BURNING. The following applies to all outdoor and agricultural burning unless granted a limited or specific exemption by the APCO (App. B). The limited exemptions granted for various types of burning are shown in table 3.03-1 and the footnotes:
1. Prohibitions. Burning is prohibited in the following areas and conditions:
a. Woodsmoke Control Zone (App. A). Prohibited during burn bans (App. A). The area is described in app. H (pg. H-1).
b. Other Areas. Prohibited during a burn ban in any other geographic area designated by the board.
c. Urban Growth Areas (App. A) (5.03C). Prohibited after December 31, 2000, and sooner if a reasonable alternate (App. A) disposal method exists for:
1) County-designated urban growth areas; and
2) Cities having a population greater than 10,000 people: (5.03C)
3) Except urban growth areas for cities which have a population less than 5,000 people that are neither within nor contiguous with a nonattainment or former nonattainment area, outdoor burning is prohibited after December 31, 2006.
d. (5.03 B) Yakima urban area as described in app. H (pg. H-2), the city of Selah, and the city of Sunnyside.
e. Burn Ignition. If an individual permit is required in tables 3.03-1 or 2 for any type of outdoor or agricultural burning, the fire shall not be ignited without first obtaining the permit.
f. Hours of Burning. (5.05) All burning shall be conducted during daylight hours (App. A).
g. Burning Without a Permit or Limited Exemption. (5.01) Burning is not allowed without an individual, annual, or general rule permit unless granted a limited exemption in tables 3.03-1 or 2 and the footnotes for the tables.
2. Requirements. (5.05)
a. Confirmation of Daily Burning Status. Prior to igniting the fire and each subsequent day, the person supervising the fire must confirm the burn ban status.
b. Demonstration of No Reasonable Alternative. (App. A) (5.04D) Anyone applying for a permit must demonstrate that there is no reasonable alternate for:
1) Safeguarding the environment; and
2) Economic viability.
c. Minimize Adverse Effects. All permits issued by the
authority will must contain requirements to insure that public
interest in air, water and land pollution and safety to life and
property is fully considered and will must be designed to
minimize air pollution as practicable. (5.04C) Permits shall be
drafted to minimize emissions. This includinges the denial of
permission to burn during periods of adverse meteorological
conditions. (5.04B)
d. Supervision of the Fire. The fire must be supervised by a person who is responsible for and capable of extinguishing the fire. The fire must not be left unattended.
e. Cessation of Burning. (5.05A)
1) During Burn Bans. (5.02A1b&c) No open burning shall may
be done when the APCO (App. B) has declared an impaired air
quality condition or ecology (App. B) has declared an air
pollution episode as described in section 3.05 (pg. 3-xx).
2) Extinguishing the Fire. When burning is prohibited the person responsible for the fire must immediately start extinguishing the fire.
3) Notification. Notification of the prohibition of burning is done by publishing a notice in a newspaper of general circulation in the area, and broadcasting the notice on radio or television stations.
4) Lapse Time to Legally Extinguish Fires During Burn Bans.
a) Land clearing, storm and flood debris, and orchard removal burns shall be extinguished within eight hours of notification of a burn ban.
b) All other burns shall be extinguished within three hours of the notification.
f. Extinguished Fire. (5.05) A fire shall be considered extinguished when there is no visible flame or smoke coming from the fire, and the burned material can be handled with bare hands.
g. Additional Requirements. Additional requirements for various types of burning are listed in subsections 3.03D2 (pg. 3-xx), 3.03E (pg. 3-xx), 3.03F2 (pg. 3-xx), and the footnotes for tables 3.03-1 and 2.
h. Requirements of Other Agencies. (5.05B) Any person responsible for fires must abide by all rules and procedures set by other agencies having any jurisdiction over outdoor and agricultural burning.
D. SPECIFIC PROVISIONS FOR OUTDOOR BURNING.
1. Prohibitions.
a. Materials. (WAC 173-425-040) (5.02A1a) Materials prohibited from burning:
1) Garbage,
2) Dead animals, or parts of dead animals,
3) Asphalt,
4) Petroleum products,
5) Paints,
6) Rubber products,
7) Plastics,
8) Paper other than what is necessary to start a fire,
9) Cardboard,
10) Treated wood,
11) Construction/demolition debris,
12) Metal, or
13) Any substance that normally emits toxic emissions, dense smoke, or obnoxious odors when burned other than natural vegetation.
b. Hauled Material. Other than firewood (App. A) for use in wood heaters (App. A), ceremonial fires, or recreational fires (App. A), material transported from an area prohibited for outdoor burning may not be burned in another area.
2. Requirements.
a. All Outdoor Burning.
1) When the burn is primarily wood > (App. B) 12 in. dia., the burn must not be ignited or fed after 12:00 noon on the day ignited.
2) Except for ceremonial, residential, tumbleweed, and recreational burning not included in general rule permits, the person doing the burning shall inform the authority of the location, quantity and type of material to burn, and duration for the burn prior to setting the fire.
b. Residential Burning.
1) Must be located on a non-combustible surface not less than 50 feet from buildings, fences, other combustible materials, and other fires.
2) Burn one pile at a time.
3) Pile size must be < (App. B) 4ft. x 4ft. x 3ft. high.
c. Storm and Flood Debris Burning.
1) Material proposed for burning was deposited by a storm that resulted in a declared emergency by a governmental authority.
2) The permit shall contain a time period for the burning.
3) The maximum time limit for this type of burning is two years after the event that deposited the debris.
4) The following variables shall be considered in determining an appropriate maximum time limit after the flood event:
a) Size of the material and the amount of drying time needed to create good burning conditions with lower emissions; and
b) Time of year that the storm event occurred.
E. ADDITIONAL SPECIFIC PROVISIONS FOR FIRE FIGHTING TRAINING FIRES.
1. Applicability. Subsection 3.03E (pg. 3-xx) is applicable to any fire department, business, or organization (App. A) using fire fighting training fires or any business using a fire to demonstrate fire equipment.
2. Requirements for All Training Fires.
a. Must comply with any other permits, licenses, or approvals that are required;
b. Must not be located in an area that is declared to be in an air pollution episode or impaired air quality condition;
c. Nuisance (App. A) laws are applicable to the fire, including nuisances related to the unreasonable interference with the enjoyment of life and property and the depositing of particulate matter or ash on other property; and
d. Notify the authority of the type and location of each fire prior to starting the training fire.
3. Additional Requirements for Structural or Natural Vegetation Training Fires. (5.03D3)
a. These types of training fires are not allowed for a business demonstrating fire equipment.
b. Notice of the fire is provided to the owners of property adjoining the property, and to the persons who potentially will be impacted;
c. On each parcel of land where an exercise is planned each structure to be burned or not burned must be identified to the authority, and;
d. A good faith inspection survey according to subsection
3.07F (pg. 3-xx) is must be conducted to determine if materials
containing asbestos are present in the structures, the inspection
is must be documented in writing and forwarded to the authority,
and asbestos that is found is must be removed prior to the
burning.
4. Additional Requirements for Aircraft Crash Rescue Fire Training.
a. Participants in these training fires must be limited to fire fighters who provide support to an airport which is:
1) Certified by the FAA (App. B); or
2) Operated to support military or governmental aviation.
b. Number of training fires allowed per year without a permit is the minimum number required by FAA or other federal safety requirements.
c. The facility must use current technology and be operated in a manner that will minimize the release of air pollutants during the fire training.
d. Prior to the initial training exercise, written approval must be obtained from the authority.
5. Permitting and Limited Exemptions. The types of permits required and limited exemptions granted are shown in table 3.03-1.
F. SPECIFIC PROVISIONS FOR AGRICULTURAL BURNING.
1. Prohibitions. No additional prohibitions.
2. Requirements.
a. A farmer must show that the burning is a BMP (App. B), or necessary to a successful operation; and there is no reasonably available practical alternative.
b. Burning is limited to natural vegetation.
c. Natural vegetation intended for agricultural burning may be transported to a stockpile site for drying and future burning providing there is no prohibition for burning at the stockpile site.
d. Burning must be done only when the wind will take the smoke away from roads, homes, population centers, and other public areas.
e. Prior to igniting a burn, the farmer must provide the authority with the location, size, and type of material for each burn.
f. Farmers who fail to report burns may have an annual permit canceled.
G. LIMITED EXEMPTIONS.
1. All Burning.
a. Individual Permit Required. The specific exemptions will be established in the permit after discussing the burn, the prohibitions, and the requirements with the proponent.
b. General Rule Permits and Permits Not Required. Limited exemptions are identified in subsections 3.03G2&3 (pg. 3-xx), table 3.03-1, the footnotes for these tables, and general rule permits located at the end of this section.
2. Outdoor Burning.
a. Diseased animals may be burned when a health officer orders the burning of all or part of the animal or other infected material to stop the spread of a disease infestation.
b. Dangerous materials may be burned when a fire protection authority orders the burning of dangerous materials because there is no approved alternative method of disposal.
3. Agricultural Burning. All exemptions are identified elsewhere.
H. SPECIFIC EXEMPTIONS. The APCO (App. B) may grant a written specific exemption for a subsection if the specific exemption will:
1. Create no more air pollution than the requirements of the subsection; and
2. Create no adverse environmental, health, or public safety effects:.
3. The document granting the specific exemption must contain:
a. The conditions of the specific exemption
b. A duration of no more than 30 consecutive days; and
c. The signature of the owner or operator of the property indicating agreement to the conditions of the specific exemption.
4. Specific exemptions will not be extended.
I. PROGRAM DELEGATIONS. Table 3.03-2 shows which types of agencies or businesses the authority may use to implement outdoor and agricultural burning programs if the co-operating agency/business complies with this subsection.
1. Permitting by Other Agencies. A local, county, state, or federal agency may qualify for a residential and recreational outdoor burning permit program if:
a. The agency agrees to accept all of the outdoor burning program available for permitting as shown in table 3.03-2;
b. The agency enters into a written agreement with the authority to adopt and enforce the regulations of the authority;
c. The authority finds that agency program is as or more effective;
d. The agency provides annual reports by Feb. 1st of each year which describe:
1) Total number of permits issued;
2) Total number of complaints received;
3) Total number of NOV (App. B) issued;
4) Total number of penalties issued;
5) Total dollar receipts;
6) Suggestions for improvement of the program in the future; and
7) An estimate of the total amount of material burned.
2. Issuing Agents.
a. Local, county, state, or federal governmental agencies or businesses may be delegated the authority to issue residential burning permits after signing a written agreement defining the administrative procedures for the issuance of permits.
b. The compliance and enforcement responsibility for these permits remains with the authority.
c. Violations or non-performance of the agreement may result in the cancellation of the vending agreement or a citation issued under article 5.
J. PERMITTING BY THE AUTHORITY. The authority shall use individual, annual, or general rule permits to authorize all forms of burning which require permits.
1. Individual Permits. Written or verbal individual permits shall be used when:
a. Permits are required by law or regulation;
b. The permits are needed for specific burning events;
c. The authority believes the proposed burn needs specific requirements or prohibitions that are not available from an annual or general rule permit;
d. The proposed burn can not meet all of the conditions of an annual or general rule permit, or
e. The permit fee is based on the specific conditions of the burn.
2. Annual Permits. Written annual permits shall be used when;
a. Permits are required by law or regulation;
b. All the requirements for burning during the year can be identified in the permit; and
c. The same annual permit fee is charged for all similar permits.
3. General Rule Permits. General rule permits are appropriated when an individual or annual permit is not required, but the authority believes some controls are needed to minimize air pollution.
a. General rule permits have no fees.
b. A person using a general rule permit must comply with all conditions of the permit or obtain an individual or annual permit.
c. The following general rule permits are adopted and included in the regulation:
1) General Rule Permit No. 3.03 - 1, Structural Fire Training Outside of Urban Growth Areas (pg. 3-xx);
2) General Rule Permit No. 3.03 - 2, Wildland Training Fires (pg. 3-xx);
3) General Rule Permit No. 3.03 - 3, Flammable Liquid or Gas Training Fires (pg. 3-xx);
4) General Rule Permit No. 3.03 - 4, Other Training Fires (pg. 3-xx); and
5) General Rule Permit No. 3.03 - 5, Large Recreational Fires (pg. 3-xx);
4. Specific Permit Conditions. Special permit conditions may be added to a written or general rule permit to include additional requirements beyond the requirements of section 3.03. They may include any of the following:
a. All Burning.
1) Restricting the hours of burning;
2) Restricting burning to a defined season;
3) Restricting the size of fires;
4) Imposing requirements for good combustion practice; or
5) Restricting burning to specified weather conditions.
6) The permittee agrees to allow the APCO to enter his/her property to conduct an investigation as defined in subsection 2.01C (pg. 2-xx).
b. Agricultural Burning.
1) Requiring the use of all or part of the agricultural burning BMPs established by the ag task force (App. A).
2) Encouraging the use of locally approved BMPs for specific crops.
5. Permit Duration.
a. Annual permits expire Dec. 31st of the current calendar year.
b. General rule permits adopted into the regulation have an indefinite duration. These remain available for use until rescinded or modified by the regulation adoption process.
c. All other permits expire 30 days maximum from the date of issuance unless approved for an alternate duration.
d. Permits other than annual permits may be extended for an additional 30 days for due cause by the APCO.
6. Permit Conditions Added after Issuance. If additional limitations are needed to prevent air pollution and/or protect property, health, safety, and comfort of persons from the effects of burning;
a. The authority shall amend an individual or annual permit; and
b. The authority must notify the permittee or responsible person of the limitations.
c. Any limitation imposed will become a condition of the permit.
7. Permit Application Process. Permit applications are available from the authority during normal working hours. The application may be submitted in person or by mail, and it must be accompanied by the application fee when one is required.
K. FEES (5.01 E)
1. Any person requesting granted an individual permit from a
local responsible jurisdiction, such as local city, town, fire
protection district, conservation district or the authority, for
an outdoor burning permit, shall pay a fee as shown in governed
by the current fee schedule of that agency adopted by the board.
then in effect. The fee schedules in effect for the Yakima
County Clean Air Authority is as shown in Article XIII, Section
13.03.
2. General rule permits have no fees.
3. Annual agricultural burning permit fees are non-refundable unless the permittee can establish and the authority agrees that the following events happened:
a. The permitted agricultural burning did not occur;
b. The need for the burning was replaced by another treatment; and
c. The burning will not occur in the future.
Table 3.03-1 Limited Exemptions, Types of Permitting.
and Specific Requirements for All Types of Burning.
See footnotes at the end of the table.
Type of Burning | Type of Burning Permit
Required a |
Types of Burning Where Limited Exemptions are Granted |
||
Prohibited Areas Sub 3.03C1 b |
Hours of Burning Sub 3.03C1f c |
Prohibited
Materials Sub 3.03D1a &F2b d |
||
Outdoor Burning | ||||
1. Ceremonial fires | Individual | 1/ | 1/ | No |
2. Fire fighting training fires 2.1 Structural training fires 2.11 Inside an urban growth area 2.12 Outside an urban growth area 2.2 Wildland training fires 2.3 Flammable liquid or gas training fires 2.4 Other training fires 2.5 Aircraft crash rescue training fires |
Individual GRP No. 3.03 - 1 GRP No. 3.03 - 2 GRP No. 3.03 - 3 GRP No. 3.03 - 4 N/A |
Yes Yes Yes Yes Yes Yes |
Yes Yes Yes Yes Yes Yes |
2/ 2/ No 2/ 2/ Yes |
3, Land clearing fires | Individual | No | 1/ | No |
4. Rare & endangered plant regeneration fires. | Individual | 1/ | 1/ | No |
5. Recreational fires 5.1 Large recreational fires 5.2 Other recreational fires 5.3 Home barbecues |
GRP No. 3.03 - 5 None None |
3/ No 5/ |
4/ Yes Yes |
No |
6. Residential | Annual | No | No | No |
7. Silvicultural | N/A | N/A | N/A | N/A |
8. Storm or flood debris | Individual | 1/ | 1/ | No |
9. Tumbleweed | None | No | No | No |
10. Weed abatement | Individual | 1/ | No | No |
11. Other outdoor burning 6/ | Individual | 1/ | 1/ | 1/ |
Agricultural Burning | ||||
12. Fence rows and windblown vegetation | None, 7/ | No | 8/ | No |
13. Irrigation or drainage ditches | None, 7/ | No | 8/ | No |
14. Orchard management 14.1 Orchard prunings 14.2 Orchard removal |
None, 7/ Individual |
No | 8/ 1/ |
No |
15. Annual agricultural burning | Annual | No | No, 8/ | No |
16. Other agricultural burning 9/ | Individual | 1/ | 8/ | 1/ |
Training Fires Not Considered Outdoor Burning | ||||
17. Fires conducted inside a fire training facility subject to a NSR approval order | None | N/A | N/A | N/A |
Yes - Limited exemption is granted.
No - Limited exemption is not granted
None - No permit is required
Individual - Individual permit required for a specific burn.
N/A - Not Applicable because the authority does not regulate this type of burning
GRP - General Rule Permit.
Annual - Annual residential or agricultural burning permit.
1/ Shall be identified in the permit issued by the authority.
2/ The burning of prohibited materials is limited to those materials and quantities needed for effective training.
3/ Nonprofit organizations are granted a limited exemption. There is no exemption for other groups or persons.
4/ A limited exemption for the hours of burning is granted, but the fire must be extinguished within three hours after the end of the event or use.
5/ Fueled only with charcoal, LP gas,natural gas, pellets, or natural fuels.
6/ Includes any type of outdoor burning not included in the table.
7/ Incidental quantities without permitting.
8/ When night burning is accepted by the ag task force (App. A) as a BMP (App. B).
9/ Includes any type of agricultural burning not included in the table
Table 3.03-2 Forms of Delegation for All Types of Burning.
See footnotes at the end of the table.
Type of Burning | Permitting Information | ||||
Delegated to the Authority a |
Type of Burning Permit Required b |
Form of Delegation from the Authority |
|||
Retained by the Authority c |
Permitting
Program
Available d |
Permit
Vending e |
|||
Outdoor Burning | |||||
1. Ceremonial fires | Yes | Individual | No | Yes | No |
2. Fire fighting training fires 2.1 Structural training fires 2.11 Inside urban growth areas 2.12 Outside urban growth areas 2.2 Wildland training fires 2.3 Flammable liquid or gas training fires 2.4 Other training fires 2.5 Aircraft crash rescue training fires |
Yes | Individual GRP No. 3.03 - 1 GRP No. 3.03 - 2 GRP No. 3.03 - 3 GRP No. 3.03 - 4 None |
Yes | No | No |
3. Land clearing | Yes | Individual | Yes | No | No |
4. Rare & endangered plant regeneration fires | Yes | Individual | Yes | No | No |
5. Recreational fires 5.1 Large recreational fires 5.2 Other recreational fires 5.3 Home barbecues |
Yes | GRP No. 3.03 - 5 None None |
Yes | No | No |
6. Residential | Yes | Annual | No | Yes | Yes |
7. Silvicultural | No | N/A | N/A | N/A | N/A |
8. Storm or flood debris | Yes | Individual | Yes | No | No |
9. Tumbleweed | Yes | None, 1/ | No | Yes | No |
10. Weed abatement | Yes | Individual | No | Yes | No |
11 Other outdoor burning 2/ | Yes | Individual | Yes | No | No |
Agricultural Burning | |||||
12. Fence rows and windblown vegetation | Yes | None, 3/ | Yes | No | No |
13. Irrigation or drainage ditches | Yes | None, 3/ | Yes | No | No |
14. Orchard management 14.1 Orchard prunings 14.2 Orchard removal |
Yes | None, 3/ Individual |
Yes | No | No |
15. Annual agricultural burning | Yes | Annual | Yes | No | No |
16. Other agricultural burning 4/ | Yes | Yes | Yes | No | No |
Training Fires Not Considered Outdoor Burning | |||||
17. Fires conducted inside a fire training facility subject to a NSR approval order | Yes | None | Yes | No | No |
Yes - The authority is delegated responsibility for this type of burning, a burning permit is required, or this type of burning may be delegated to another agency or business.
No - The authority is not delegated responsibility for this type of burning, or this type of burning may be delegated to another agency or business.
None - No permit is required
Individual - Individual permit required for a specific burn.
N/A - Not Applicable because the authority does not regulate this type of burning
GRP - General Rule Permit.
Annual - Annual residential or agricultural burning permit.
1/ Applies when only tumbleweeds are burned in the fire.
2/ Includes any type of outdoor burning not included in the table.
3/ Incidental quantities without permitting.
4/ Includes any type of agricultural burning not included in the table.
Table 3.03-3 Notification Requirements Before Burning
See footnotes at the end of the table
Type of Burning | Type of Burning Permit Required a |
Prior Notification Required Before Igniting the Fire |
|
Authority b |
Neighbors c |
||
Outdoor Burning | |||
1. Ceremonial fires | Individual | No | No |
2. Fire fighting training fires 2.1 Structural training fires 2.11 Inside an urban growth area 2.12 Outside an urban growth area 2.2 Wildland training fires 2.3 Flammable liquid or gas training fires 2.4 Other training fires 2.5 Aircraft crash rescue training fires |
Individual GRP No. 3.03 - 1 GRP No. 3.03 - 2 GRP No. 3.03 - 3 GRP No. 3.03 - 4 N/A |
Yes Yes Yes Yes Yes Yes, 3/ |
1/ Yes, 2/ Yes, 2/ Yes, 2/ Yes, 2/ No |
3. Land clearing fires | Individual | Yes | 1/ |
4. Rare & endangered plant regeneration fires | Individual | Yes | 1/ |
5. Recreational fires 5.1 Large recreational fires 5.2 Other recreational fires 5.3 Home barbecues |
GRP No. 3.03 - 5 None None |
Yes No No |
Yes No No |
6. Residential | Annual | No | No |
7. Silivicultural | N/A | N/A | N/A |
8. Storm or flood debris | Individual | Yes | 1/ |
9. Tumbleweed | None | No | No |
10. Weed abatement | Individual | Yes | 1/ |
11. Other outdoor burning | Individual | Yes | 1/ |
Agricultural Burning | |||
12, Fence rows and windblown vegetation | None, 4/ | No | No |
13. Irrigation or drainage ditches | None, 4/ | No | No |
14. Orchard management 14.1 Orchard prunings 14.2 Orchard removal |
None, 4/ Individual |
No Yes |
No 1/ |
15. Annual agricultural burning | Annual | Yes | No |
16. Other agricultural burning | Individual | Yes | 1/ |
Training Fires Not Considered Outdoor Burning | |||
17. Fires conducted inside a fire training facility subject to a NSR approval order | None | 5/ | 5/ |
1/ As required in the individual permit.
2/ As required by the general rule permit.
3/ Written approval required prior to the first training exercise.
4/ Incidental quantities without a permit.
5/ As required in the NSR approval order.
STRUCTURAL FIRE TRAINING OUTSIDE OF URBAN GROWTH AREAS
A. PURPOSE. To control emissions from structural training
fires and to satisfy the permitting requirements by a general
rule.
B. APPLICABILITY.
1. Any fire department (App. A) planning to conduct structural training fire outside of an urban growth area.
2. The owner or operator of the land where the training fire is conducted.
C. REFERENCES. Sections 3.01 (pg. 3-xx), 3.03 (pg. 3-xx), 3.05 (pg. 3-xx), and 3.07 (pg. 3-xx).
D. DURATION. Indefinite.
E. REQUIREMENTS.
1. General. (3.03C)
a. Confirmation of Daily Burning Status. Prior to igniting the fire and each subsequent day, the person supervising the fire must confirm the burn ban status.
b. Supervision of the Fire. The fire must be supervised by a person who is responsible for and capable of extinguishing the fire. The fire must not be left unattended.
c. During Burn Bans. No burning may be done when the APCO has declared an impaired air quality condition or ecology has declared an air pollution episode as described in section 3.05 (pg. 3-xx).
1) Extinguishing the Fire. When burning is prohibited the person responsible for the fire must extinguish the fire.
2) Notification. Notification of the prohibition of burning is done by publishing a notice in a newspaper of general circulation in the area, and broadcasting the notice on radio or television stations.
3) Lapse Time. The fire must be extinguished within three hours of notification of a burn ban.
2. Specific. (3.03D & E)
a. Prohibited Materials. The burning of prohibited materials listed in subsection 3.03D1a is limited to those materials and quantities needed for effective structural training fire.
b. Nuisance Rules. These rules are applicable to the fire, including nuisances related to the unreasonable interference with the enjoyment of life and property and the depositing of particulate matter or ash on other property
c. Structure Identification. On each parcel of land where an exercise is planned each structure to be burned or not burned must be identified to the authority.
d. Asbestos Survey and Removal. A survey is conducted in accordance with subsection 3.07F (pg. 3-xx) to determine if materials containing asbestos are present in the structures, the survey is documented in writing and forwarded to the authority.
e. Asbestos Removal. Asbestos that is found is removed prior to the burning.
F. NOTIFICATION. (3.03D2a2) Prior to the start of the training the fire department conducting the training fire shall inform:
1. The authority of the location, quantity and type of material to burn, and duration for the training fire; and
2. The owners of property adjoining the property, and persons who potentially will be impacted.
G. REQUIREMENTS OF OTHER AGENCIES. (3.03C3i) Any person responsible for fires must abide by all rules and procedures set by other agencies having any jurisdiction over outdoor burning.
H. VIOLATIONS. Failure to comply with the requirements of this general rule permit is a violation, and the following are the remedies for a violation:
1. Voiding any further training fires under general rule permits and obtaining individual written permits with the appropriate requirements and fees and/or:
2. Compliance and enforcement action under article 5.
WILDLAND TRAINING FIRES
A. PURPOSE. To control emissions from wildland training fires and to satisfy the permitting requirements by a general rule.
B. APPLICABILITY.
1. Any fire department planning to conduct wildland training fires.
2. The owner or operator of the land where the training fire is conducted.
3. This general rule permit is not applicable to the following:
a. Silvicultural burning administered by the DNR, or:
b. Burning structures at the location of a wildland training fire.
C. REFERENCES. Sections 3.01 (pg. 3-xx), 3.03 (pg. 3-xx), and 3.05 (pg. 3-xx).
D. DURATION. Indefinite.
E. REQUIREMENTS.
1. General. (3.03C)
a. Confirmation of Daily Burning Status. Prior to igniting the fire and each subsequent day, the person supervising the fire must confirm the burn ban status.
b. Supervision of the Fire. The fire must be supervised by a person who is responsible for and capable of extinguishing the fire. The fire must not be left unattended.
c. During Burn Bans. No burning may be done when the APCO has declared an impaired air quality condition or ecology has declared an air pollution episode as described in section 3.05 (pg. 3-xx).
1) Extinguishing the Fire. When burning is prohibited the person responsible for the fire must extinguish the fire.
2) Notification. Notification of the prohibition of burning is done by publishing a notice in a newspaper of general circulation in the area, and broadcasting the notice on radio or television stations.
3) Lapse Time. The fire must be extinguished within eight hours of notification of a burn ban.
2. Specific. (3.03D & E)
a. Prohibited Materials. The burning of prohibited materials listed in subsection 3.03D1a (pg. 3-xx) is prohibited.
b. Nuisance Rules. These rules are applicable to the fire, including nuisances related to the unreasonable interference with the enjoyment of life and property and the depositing of particulate matter or ash on other property
c. Land Identification. Each parcel of land where an exercise is planned must be identified to the authority.
F. NOTIFICATION. (3.03D2a2) Prior to the start of the training fire the fire department conducting the training shall inform:
1. The authority of the location, quantity and type of material to burn, and duration for the training fire; and
2. The owners of property adjoining the property persons who potentially will be impacted.
G. REQUIREMENTS OF OTHER AGENCIES. (3.03C3i) Any person responsible for fires must abide by all rules and procedures set by other agencies having any jurisdiction over outdoor burning.
H. VIOLATIONS. Failure to comply with the requirements of this general rule permit is a violation, and the following are the remedies for a violation:
1. Voiding any further training fires under general rule permits and obtaining individual written permits with the appropriate requirements and fees and/or:
2. Compliance and enforcement action under article 5.
FLAMMABLE LIQUID OR GAS TRAINING FIRES
A. PURPOSE. To control emissions from flammable or gas liquid fires for training or demonstrating the proper use of fire equipment and to satisfy the permitting requirements by a general rule.
B. APPLICABILITY.
1. Any fire department conducting flammable liquid or gas training fires;
2. Any company demonstrating the use of fire suppression equipment; or
3. Any company or organization training employees in the use of fire extinguisher; and
4. The owner or operator of the land where the training fire is conducted.
C. REFERENCES. Sections 3.01 (pg. 3-xx), 3.03 (pg. 3-xx), and 3.05 (pg. 3-xx).
D. DURATION. Indefinite.
E. REQUIREMENTS.
1. General. (3.03C)
a. Confirmation of Daily Burning Status. Prior to igniting the fire and each subsequent day, the person supervising the fire must confirm the burn ban status.
b. Supervision of the Fire. The fire must be supervised by a person who is responsible for and capable of extinguishing the fire. The fire must not be left unattended.
c. During Burn Bans. No burning may be done when the APCO has declared an impaired air quality condition or ecology has declared an air pollution episode as described in section 3.05 (pg. 3-xx).
1) Extinguishing the Fire. When burning is prohibited the person responsible for the fire must extinguish the fire.
2) Notification. Notification of the prohibition of burning is done by publishing a notice in a newspaper of general circulation in the area, and broadcasting the notice on radio or television stations.
3) Lapse Time. The fire must be extinguished within 15 minutes of notification of a burn ban.
2. Specific. (3.03D & E)
a. Prohibited Materials. The burning of prohibited materials listed in subsection 3.03D1a is limited to those materials and quantities needed for effective structural training fire.
b. Nuisance Rules. These rules are applicable to the fire, including nuisances related to the unreasonable interference with the enjoyment of life and property and the depositing of particulate matter or ash on other property
c. Container for the Fire. The training fire is contained within a noncombustible container or apparatus ≤ 4 ft. x 4 ft. in size.
F. NOTIFICATION. (3.03D2a2) Prior to the start of the training the person doing the training or demonstration shall inform:
1. The authority of the location, quantity and type of material to burn, and duration for the training fire; and
2. The owners of property adjoining the property, and to the persons who potentially will be impacted.
G. REQUIREMENTS OF OTHER AGENCIES. (3.03C3i) Any person responsible for fires must abide by all rules and procedures set by other agencies having any jurisdiction over outdoor burning.
H. VIOLATIONS. Failure to comply with the requirements of this general rule permit is a violation, and the following are the remedies for a violation:
1. Voiding any further training fires under general rule permits and obtaining individual written permits with the appropriate requirements and fees and/or:
2. Compliance and enforcement action under article 5.
OTHER TRAINING FIRES
A. PURPOSE. To control emissions from other training fires and to satisfy the permitting requirements by a general rule.
B. APPLICABILITY.
1. Any fire department planning to conduct an training fire < 10 ft. x 10 ft. x 8 ft. high in size which is not covered by another general rule permit; and
2. The owner or operator of the land where the training fire is conducted.
3. This general rule permit is not applicable for training fires which do not meet all the requirements of this general rule.
C. REFERENCES. Sections 3.01 (pg. 3-xx), 3.03 (pg. 3-xx), and 3.05 (pg. 3-xx).
D. DURATION. Indefinite.
E. REQUIREMENTS.
1. General. (3.03C)
a. Confirmation of Daily Burning Status. Prior to igniting the fire and each subsequent day, the person supervising the fire must confirm the burn ban status.
b. Supervision of the Fire. The fire must be supervised by a person who is responsible for and capable of extinguishing the fire. The fire must not be left unattended.
c. During Burn Bans. No burning may be done when the APCO has declared an impaired air quality condition or ecology has declared an air pollution episode as described in section 3.05 (pg. 3-xx).
1) Extinguishing the Fire. When burning is prohibited the person responsible for the fire must extinguish the fire.
2) Notification. Notification of the prohibition of burning is done by publishing a notice in a newspaper of general circulation in the area, and broadcasting the notice on radio or television stations.
3) Lapse Time. The fire must be extinguished within three hours of notification of a burn ban.
2. Specific. (3.03D & E)
a. Prohibited Materials. The burning of prohibited materials listed in subsection 3.03D1a (pg. 3-xx) is limited to those materials and quantities needed for effective training fire.
b. Structures. The burning of any structure under this general rule permit is prohibited.
c. Nuisance Rules. These rules are applicable to the fire, including nuisances related to the unreasonable interference with the enjoyment of life and property and the depositing of particulate matter or ash on other property.
F. NOTIFICATION. (3.03D2a2) Prior to the start of the training fire the fire department shall inform:
1. The authority of the location, quantity and type of material to burn, and duration for the training fire; and
2. The owners of property adjoining the property, and to the persons who potentially will be impacted.
G. REQUIREMENTS OF OTHER AGENCIES. (3.03C3i) Any person responsible for fires must abide by all rules and procedures set by other agencies having any jurisdiction over outdoor burning.
H. VIOLATIONS. Failure to comply with the requirements of this general rule permit is a violation, and the following are the remedies for a violation:
1. Voiding any further training fires under general rule permits and obtaining individual written permits with the appropriate requirements and fees and/or:
2. Compliance and enforcement action under article 5.
LARGE RECREATIONAL FIRES
A. PURPOSE. To control emissions from large recreational fires and fires at exhibits, and to satisfy the permitting requirements by a general rule.
B. APPLICABILITY. This general rule is applicable for any a recreational or exhibition fire > 3 ft. in dia. and 2 ft. high which is intended for any of the following uses:
1. Nonprofit organizations conducting social, athletic, or religious events;
2. Persons having a recreational fire in a location that is not prohibited; or
3. Persons using fires for exhibits at public even; and
4. The rule is applicable to the owner or operator of the land where the large recreational fire occurs.
C. REFERENCES. Sections 3.01 (pg. 3-xx), 3.03 (pg. 3-xx), and 3.05 (pg. 3-xx).
D. DURATION. Indefinite.
E. REQUIREMENTS.
1. General. (3.03C)
a. Confirmation of Daily Burning Status. Prior to igniting the fire and each subsequent day, the person supervising the fire must confirm the burn ban status.
b. Supervision of the Fire. The fire must be supervised by a person who is responsible for and capable of extinguishing the fire. The fire must not be left unattended.
c. During Burn Bans. No burning may be done when the APCO has declared an impaired air quality condition or ecology has declared an air pollution episode as described in section 3.05 (pg. 3-xx).
1) Extinguishing the Fire. When burning is prohibited the person responsible for the fire must extinguish the fire.
2) Notification. Notification of the prohibition of burning is done by publishing a notice in a newspaper of general circulation in the area, and broadcasting the notice on radio or television stations.
3) Lapse Time. The fire must be extinguished within three hours of notification of a burn ban.
2. Specific. (3.03D & E)
a. Prohibited Materials. The burning of prohibited materials listed in subsection 3.03D1a is prohibited.
b. Prohibited Areas. A limited exemption for subsection 3.03C1 (pg. 3-xx) may be granted bly the APCO if the proponent presents an acceptable proposal.
c. Prohibited Hours.
1) Persons conducting these types of fires are granted a limited exemption from subsection 3.03C1e (pg. 3-xx) to conduct the fire after sunset, but
2) The fire must be extinguished within three hours after the end of the event or use.
d. Nuisance Rules. These rules are applicable to the fire, including nuisances related to the unreasonable interference with the enjoyment of life and property and the depositing of particulate matter or ash on other property
e. Location of Fire. Located on a non-combustible surface not less than 50 feet from buildings, fences, other combustible materials, and other fires or 500 ft. from forest slash.
f. Maximum Size of the Fire. The maximum size of the fire is 10 ft. x 10 ft. x 8 ft.
F. NOTIFICATION. (3.03D2a2) Prior to the start of the large recreational fire the person conducting the fire shall inform:
1. The authority of the location, quantity and type of material to burn, and duration for the fire; and
2. The owners of the adjoining property and the persons who potentially will be impacted.
G. REQUIREMENTS OF OTHER AGENCIES. (3.03C3i) Any person responsible for fires must abide by all rules and procedures set by other agencies having any jurisdiction over outdoor burning.
H. VIOLATIONS. Failure to comply with the requirements of this general rule permit is a violation, and the following are the remedies for a violation:
1. Voiding any further recreational or exhibition fires under general rule permits and obtaining individual written permits with the appropriate requirements and fees and/or:
2. Compliance and enforcement action under article 5.
3.04 WOODSTOVES AND FIREPLACES WOOD HEATERS
A. PURPOSE (9.01) Without limiting the power of the Yakima
County Clean Air Authority or its Director or Agents, the
Authority states that it shall be its policy, to the extent that
it is compatible with the enforcement of the regulations, to
instruct and educate the public and violators of the hazards to
health caused by woodsmoke, and to authorize educational
materials concerning those dangers. To define a program to
control and reduce woodsmoke emissions from wood heaters.
B. APPLICABILITY (New section) This section applies to any device which burns wood, wood products, or other nongaseous or nonliquid fuels and is rated less than one million Btu per hour.
C. LIMITATIONS ON SALES, ADVERTISEMENT, AND INSTALLATION OF
SOLID FUEL BURNING DEVICES. WOOD HEATERS. (9.04)
A. After January 1, 1992, no used solid fuel burning devices
shall be installed in new or existing buildings unless such
device is either Oregon Department of Environment Quality Phase
II or EPA certified, or a pellet stove either certified or exempt
from certification by the EPA or a fireplace furnace with a
letter of exemption from the Washington State Department of
Ecology and the United States Environmental Protection Agency.
B. SOLID FUEL BURNING DEVICES.
After January 1, 1995, a person shall not advertise to sell, offer to sell, sell, bargain, exchange, or give away a solid fuel burning device unless it has been certified and labeled in accordance with procedures and criteria specified in "40 CFR 60 Subpart AAA - Standards of Performance for Residential Wood Heaters" as amended through July 1, 1990, and meets the following particulate air contaminant emission standards and the test methodology of the EPA in effect on January 1, 1991, or an equivalent standard under any test methodology adopted by the EPA subsequent to such date:
1. Two and one-half (2 1/2) grams per hour for catalytic woodstoves; and
2. Four and one-half (4 1/2) grams per hour for all other solid fuel burning devices.
3. For purposes of this subsection, "equivalent" shall mean the emissions limits specified in this subsection multiplied by a statistically reliable conversion factor determined by ecology that relates the emission test results from the methodology established by the EPA prior to May 15, 1991, to the tests results from the methodology subsequently adopted by that agency.
C. FIREPLACES.
After January 1. 1997, a person shall not advertise to sell, offer to sell, sell, bargain, exchange, or give away a factory built fireplace unless it meets the 1990 EPA standards for woodstoves or equivalent standard that may be established by he state building code council by rule. Subsection 9.04(A) shall not apply to fireplaces, including factory built fireplaces, and masonry fireplaces.
1. Restrictions on Advertisement and Sale.
a. Uncertified wood heaters shall not be advertised or sold.
b. Any wood heater offered for sale shall meet the following PM (App. A) emission standards:
(1) Catalytic wood heaters - ≤ 2.5 grams/hr.
(2) All other wood heaters - ≤ 4.5 grams/hr.
2. Restrictions on Installation. Uncertified wood heaters shall not be installed. The enforcement of the installation requirements may also be enforced by other agencies.
3. Educational Materials. (9.04D) (WAC 173-433-110(5))
Persons Retailers who selling new solid fuel heating devices wood
heaters shall distribute must provide and verbally explain
educational materials to customers. purchasing new wood stoves
describing when a stove can and cannot be legally used. The
educational information should include that opacity levels of ten
percent or less can be achieved through proper operation. If
necessary, the retailer should verbally explain the educational
materials to assure that the purchaser understands the
information.
4. Installation of Uncertified Wood Heaters. (OAPCA Reg 1, 8.15) (App. B) It is unlawful to install an uncertified wood heater, unless granted a limited exemption in subsection 3.04D (pg. 3-xx), in new or existing buildings or structures. Uncertified wood heaters installed after January 1, 1992, are a violation of this subsection and must be promptly removed from the structure.
5. Sale and Disposal of Uncertified Wood Heaters. (OAPCA Reg 1, 8.17) When an uncertified wood heater is to be permanently removed from its location it shall be made inoperable. A removed uncertified wood heater shall not be sold, bartered, traded, or given away for a purpose other than recycling of the materials.
D. LIMITED EXEMPTIONS (9.04E) The following solid fuel devices
wood heaters shall be are granted a limited exemption from the
requirements of Section 9.04B of subsections 3.04C4 & 5 (pg.
3-xx):
1. Boilers (App. A);
2. Furnaces (App. A);
3. Cookstoves; Antique Wood Stoves and Heaters. Antique
wood cookstoves and heaters manufactured prior to 1940 may be
installed and used in the manner of their original design. (1997
UBC, WAC 51-40-510.3) (App. B).
4. Historic Sites. Any building or structure listed on the National Register of Historic Sites or on the Washington State Register of Historic Places is allowed to burn wood, coal, or wood products in the same manner as when it was a functional facility. Use will not be permitted during a burn ban as described in section 3.05 (pg. 3-xx).
5. Existing Uncertified Wood Heater. Owners of uncertified wood heaters installed prior to January 1, 1992 may continue to use these devices at the original locations as long as they meet the provisions of the general requirements in subsection 3.04E (pg. 3-xx).
E. GENERAL REQUIREMENTS.
1. Opacity. (9.02) No person owning, operating or in
control of a residential solid fuel burning device shall cause,
allow or discharge to the ambient air any emissions from such
device which are of an opacity greater than twenty percent (20%)
except for the purposes of public education, then the opacity
level shall not be greater than ten percent (10%). It is a
violation to operate a wood heater in a manner that emits a smoke
plume exceeding the opacity standard. The standard and test
procedures are stated in app. D.
2. Prohibitive Fuel Types (9.03) A person shall not cause or
It is prohibited to allow any of the following materials to be
burned in a solid fuel burning device wood heater:
a. Garbage;
b. Treated wood;
c. Plastic and plastic products;
d. Rubber products;
e. Animals; Dead animals, or parts of dead animals;
f. Asphaltic products;
g. Waste petroleum products;
h. Paints and chemicals, or;
i. Any substance, other than properly seasoned wood and
paper used to start the fire, Fuel which normally emits dense
smoke or obnoxious odors.
3. Burning During Burn Bans. Wood heaters must not be used during a burn ban as describe in section 3.05 (pg. 3-xx). Smoke visible from a chimney, flue or exhaust duct constitutes evidence of unlawful operation. This presumption may be refuted by demonstration that the smoke was not caused by a wood heater. The provisions of this requirement are enforceable on a complaint or surveillance basis.
4. General Standards. Wood heaters may not be operated in violation of subsections 3.01C1d (pg. 3-xx) and 3.01C1e (pg. 3-xx).
3.05 PROHIBITION OF VISIBLE EMISSIONS DURING AIR POLLUTION
EPISODE BURN BANS (9.05)
A. PURPOSE.
1. To prevent and avoid increasing unhealthful ambient air quality conditions.
2. To define the legal conditions for outdoor and agricultural burning and the use of wood heaters during burn bans (App. A).
B. APPLICABILITY. Applies to all outdoor and agricultural burning, and wood heater use unless exempted elsewhere in this section.
C. DECLARATION AND CRITERIA.
1. Impaired Air Quality. This is declared and terminated by the APCO (App. B), and it applies to:
a. The woodsmoke control zone as defined in app. H (pg. H-xx) and shown on the map in app. I (pg. I-2); and/or
b. Any other area defined by the board.
c. It indicates air contaminants above threshold levels (App. A) in table 3.05-1.
for an Impaired Air Quality Event
Pollutant | Threshold Level | |
First or Yellow Stage | Second or Red Stage | |
PM10 (App. B) | > 60 µg/m3(App. B) for a 24 hour average | > 105 µg/m3 for a 24 hour average |
CO (App. B) | > 8 ppm for an 8 hour average | No Level |
a. Stages. The four stages of an air pollution episode are forecast, alert, warning, and emergency.
b. Declaration and Termination. The director of ecology may declare and terminate the first three stages. Only the governor may declare and terminate the emergency stage of an episode.
D. REQUIREMENTS.
1. Outdoor and Agricultural Burning. Extinguish all burning as required in subsection 3.03C2 (pg. 3-xx) and do not ignite any burns.
2. Fire Training Fires. Do not ignite these fires.
3. Wood Heaters. (9.05A1) Any person in a residence or
commercial establishment which has an adequate source of heat
other than a SFBD wood heater shall burn the wood heater
according to table 3.05-2.
c. Not use any SFBD whenever the Department of Ecology or
the Authority has determined under RCW 70.94.715 that any Air
Pollution Episode exists in that area.
b. Not use any solid fuel burning device except those which are either Oregon Department of Environmental Quality Phase II or United States Environmental Protection Agency certified or certified by the Department_of Ecology under RCW 70.94.457(1) or a pellet stove either certified or issued an exemption by the United States Environmental Protection Agency in accordance with Title 40, Part 60 of the Code of Federal Regulations in the geographic area and for the period of time that a first stage of impaired air quality has been determined by the Department of Ecology or by the Yakima County Clean Air Authority. The geographic area affected by a first stage of impaired air quality is the Woodsmoke Control Zone as defined in Section 1.03(84). A first stage of impaired air quality is reached when particulates ten microns and greater in diameter are at an ambient level of 75 micrograms per cubic meter measured on a 24 hour average or when CO is at an ambient level of 8 parts of contaminant per million parts of air by volume measured on an 8 hour average.
d. Not use any solid fuel burning device, including those that meet the standards set forth in RCW 70.94.457, in any geographic area for the period of time that a second stage of impaired air quality has been determined by the Department of Ecology or the Yakima County Clean Air Authority. The geographic area affected by a second stage of impaired air quality is the Woodsmoke Control Zone as defined in Section 1.03(84). A second stage of impaired air quality is reached when particulates ten microns and smaller in diameter are at an ambient level of 90 micrograms per cubic meter measured on a 24 hour average or when CO is at an ambient level of 8 parts of contaminant per million parts of air by volume measured on an 8 hour average.
E. EXEMPTIONS.
1. Outdoor and Agricultural Burning. There are no exemptions during a burn ban.
2. Wood Heater is the Only Heat Source. Homes or commercial establishments with no source of adequate heat other than a wood heater are exempt from the prohibition in this section. Adequate heat means a system that can maintain a temperature of 70°F (App. B) three feet off the floor in normally inhabited areas of a dwelling when the heater is operating as designed.
Permitted in Designated Areas During Burn Bans.
Yes - Burning or use is permitted, No - Burning or use is not permitted.
Type of Burning 1/ |
Type of Burn Ban | |||
Impaired Air Quality | Air Pollution Episode | |||
First Stage a |
Second Stage b |
Forecast c |
Alert, Warning, or
Emergency d |
|
1. Outdoor | No | No | No | No |
2. Agricultural | No | No | No | No |
3. Fire Fighting Training Fires | No | No | No | No |
4. Wood Heaters | ||||
4.1 Pellet Stove | Yes | No | Yes | No |
4.2 EPA Certified Woodstove | Yes | No | Yes | No |
4.3 DEQ Phase 2 Woodstove | Yes | No | Yes | No |
4.4 EPA Exempted Device | No | No | Yes | No |
4.5 Sole Source of Heat | Yes | Yes | Yes | Yes |
4.6 All Others | No | No | Yes | No |
1/ Definitions of types of burning are in app. A.
3.06 CHLOROFLUOROCARBONS STRATOSPHERIC OZONE-DEPLETING
CHEMICALS(10.01)
A. PURPOSE. To prevent the unnecessary release of
stratospheric ozone-depleting chemicals. The Board recognizes
that the release of chlorofluorocarbons into the atmosphere
contributes to the destruction of stratospheric ozone and such
destruction threatens plant and animal life. The Board further
recognizes that unnecessary release of chlorofluorocarbons should
be eliminated when such times as chlorofluorocarbon extraction
equipment are readily available to local businesses and the
Department of Ecology has adopted rules to control
chlorofluorocarbon emission sources including performance
specifications for chlorofluorocarbon extraction and/or recycling
equipment
B. APPLICABILITY.
1. All persons who manufacture, handle, store, use, or dispose of stratospheric ozone depleting chemicals.
2. Those chemicals are listed in section 602 of Title VI of the FCAA.
C. PROHIBITION. The willful release of ozone-depleting chemicals is prohibited.
3.07 ASBESTOS CONTROL (New Section, 5.09E)
E. Asbestos.
No person shall remove or otherwise disturb asbestos, to the extent that asbestos fibers may become airborne, without notifying the Authority ten (10) business days prior to removal. If removal is necessary due to an emergency, the ten day waiting period may be waived by the Authority.
1. Private Residents.
Private homeowners, when removing friable asbestos materials from their normally occupied or will be normally occupied homes, may be required to remove the asbestos materials according to the National Emission Standard for Hazardous Air Pollutants (NESHAPS) as set forth in Title 40 Code of Federal Regulations part 61, as the same now exists or may be amended. Removal and disposal of non-friable asbestos materials shall be conducted in accordance with practices and procedures approved by the Authority.
2. Small Quantity Asbestos Material.
Asbestos Materials in quantities less than 160 square feet or 260 linear feet must be removed and disposed of according to practices and procedures approved by the Authority.
3. Commercial, Industrial or other sources.
No person shall demolish any commercial, institutional, or industrial building, or any residential facility constructed to house four (4) or more families without first performing a thorough inspection, to be conducted by a qualified expert to determine the quantities and types of asbestos materials present. If it is determined that such building contains asbestos, no person shall commence the demolition of such facility without complying with the requirements of NESHAPS, the Federal Rule stated in E (1) above.
4. Fees or Administrative Charges.
Fees associated with this subsection (5.09(E)) shall be in accordance with Article XIII, Section 13.04 of this regulation.
A. PURPOSE. To prevent asbestos emissions from the disturbance of asbestos-containing materials (*) which could jeopardize public health or safety. (SCAPCA Art. IX, Sect. 9.01 -> 9.08).
B. APPLICABILITY. This section applies to the use, maintenance, renovation, or demolition of any facility (*) or vessel with ACM (*) or suspect ACM (*). It also applies to any activity which could disturb ACM.
C. COMPLIANCE. In addition to the requirements of this section, all sources are required to comply with the provisions of WAC 173-400-075(1), 40 CFR Part 61, and 40 CFR Part 763. The additional requirements in 40 CFR Part 763 that pertain only to K -> 12 public and private schools are not included in this regulation, but the source must comply with them.
D. DEFINITIONS. The following are the definitions for words and phrases used only in this section.
1. AHERA (App. B) Building Inspector. A person who has successfully completed the training requirements established by EPA (App. B) for a building inspector and whose certification is current.
2. AHERA Project Designer. A person who has successfully completed the training requirements established by EPA for an abatement project designer and whose certification is current.
3. Asbestos. The asbestiform varieties of actinolite, amosite, tremolite, chrysotile, crocidolite, or anthophyllite.
4. Asbestos-Containing Material (ACM). Any material containing more than one percent (1%) asbestos.
5. Asbestos Project. Any activity involving the abatement, renovation, demolition, removal, salvage, clean-up or disposal of ACM or ACM waste or any other action that disturbs or is likely to disturb any ACM. It does not include the application of duct tape, rewettable glass cloth, canvas, cement, paint, or other non-asbestos materials to seal or fill exposed areas where asbestos fibers may be released; or the removal of sealants, coatings, and mastic bound in asphalt roofing with no felt layers containing ACM.
6. Asbestos Survey. A written report describing an inspection using the procedures in EPA regulations, or an alternate method that has received the prior written approval from the APCO (App. B), to determine whether materials or structures to be worked on, renovated, removed, or demolished contain asbestos (*).
7. Competent Person. A person who is capable of identifying asbestos hazards and selecting the appropriate asbestos control strategy; has the authority to take prompt corrective measures to eliminate the hazards; and has been trained and is currently certified in accordance with the standards established by L&I (App. B), OSHA (App. B), or EPA. (App. B)
8. Component. Any equipment, pipe, structural member, or other item covered or coated with, or manufactured from ACM.
9. Demolition. Wrecking, razing, leveling, dismantling, or burning of a structure, and making the structure permanently uninhabitable or unusable.
10. Facility. Any institutional, commercial, public, industrial, or residential structure, installation, or building.
11. Friable Asbestos-Containing Material. ACM that, when dry, can be crumbled, disintegrated, or reduced to powder by hand pressure.
12. Glove Bag. A sealed compartment with attached inner gloves used for the handling of ACM. Properly installed and used, glove gags provide a small work area enclosure typically used for small-scale asbestos stripping operations.
13. Leak-Tight Container. A dust and liquid tight container at least 6-mil thick that encloses ACM waste and prevents solids or liquids from escaping. Such containers may include sealed plastic bags, metal or fiber drums, and sealed polyethylene plastic bags.
14. Nonfriable Asbestos-Containing Material. ACM that, when dry, cannot be crumbled, disintegrated, or reduced to powder by hand.
15. Owner-Occupied, Single-Family Residence. Any non-multiple unit building containing living space that is currently occupied by one family who owns the property as their domicile. This includes houses, mobile homes, trailers, detached garages, houseboats, and houses with a "mother-in-law apartment" or "guest room".
16. Renovation. Altering a structure or component (*) any way, other than demolition.
17. Suspect Asbestos-Containing Material. Material that has historically contained asbestos.
E. MANAGEMENT OF ACM.
1. Condition.
a. ACM which is not likely to be disturbed by renovation (*) does not have to be removed.
b. The ACM in these locations must be maintained in a stable and damage free condition to prevent asbestos emissions.
c. ACM in an unstable, friable condition needs to be removed, encapsulated, or enclosed.
d. ACM in structures planned for demolition must be removed prior to the start of the demolition work.
2. Practices. Acceptable practices are one or more of the following to insure stable ACM conditions:
a. Avoiding the ACM by restricting access and/or signing;
b. Enclosing the ACM with a wall or other barrier;
c. Treating the ACM with a bridging encapsulation compound; or
d. Conducting periodic inspections to insure the ACM is still in a stable condition.
F. ASBESTOS SURVEY REQUIREMENTS.
1. Survey Requirements. Before doing any renovation or demolition an asbestos survey (*) must be performed by an AHERA building inspector (*) except renovation of for an owner-occupied, single-family residences. (*)
2. Records. The owner or operator of the facility must do the following:
a. Post a summary of the survey at the location on the work site where control of entry is maintained or communicate in writing to all persons who may come into contact with the ACM.
b. Retain a copy of all asbestos survey records for at least two years.
c. Record the condition and location of all known ACM remaining after completion of a renovation project.
G. NOTIFICATION.
1. General Requirements. Work must not be done on any project which could disturb ACM unless a complete notification has been submitted by the owner or operator to the authority on approved forms.
a. Duration of the project shall be commensurate with the amount of work.
b. All projects require notification except:
1) Asbestos projects other than demolition involving less than 10 lf (App. B) or 48 sf (App. B) per structure of ACM in a calendar year.
2) Removal and disposal of caulking or window-glazing.
3) Renovation or demolition of detached sheds, garages, or out-buildings located at owner-occupied single family dwellings.
c. Notification is required and the following apply:
1) The renovation or demolition of a facility (*) or vessel containing ACM or suspect ACM (*) more than the limits in subsection 3.07G1b(1) (pg. 3-xx).
2) A copy of the notification, all amendments, the asbestos survey, and any order of approval (App. A) for an alternate means of compliance must be available at all times during work at the asbestos project site.
3) Notification or amendment must be filed at least ten days prior to the planned start date.
4) A copy of all asbestos notification records must be retained for at least two years by the owner or operator of the facility.
d. Multiple Projects. Notification for multiple asbestos projects on contiguous properties may be filed on one form if:
1) Work is performed by the same contractor; and
2) A work plan is submitted that includes:
a) A map of the structures;
b) The site address for each structure;
c) The amount and type of ACM in each structure;
d) The schedule for performing the asbestos project work
e. Annual Notification. A property owner or owner's agent may file one annual notification for asbestos projects at one or more facilities on contiguous properties in one calendar year if:
1) The annual notification is filed at least ten days prior to commencing work on any asbestos project; and
2) The total amount of ACM for all asbestos projects is less than 260 lf or 160 sf.
f. Duration. Notifications are valid for no more than twelve months from the original notification date.
2. Amendments.
a. Mandatory. Must be submitted for any of the following and must be accompanied by the appropriate fee.
1) Increase in the project type or job size that increases the fee; or
2) Changes in the type of ACM that will be removed; or
3) Changes in the start date, completion date, or work schedule, including hours or days of work.
b. Optional. May be submitted for any other change in a notification.
1) Submitted by phone or fax and there is a minimal effort required to review it, an amendment fee will not be charged.
2) Submitted in writing on notification forms, an amendment fee will be charged.
c. Timing. Will not be accepted after the completion date on the current notification or latest amendment.
3. Emergencies.
a. Advance notification is not required, if:
1) A sudden, unexpected event occurred that resulted in a public health or safety hazard; or
2) The project must proceed immediately to protect equipment, ensure continuous vital utilities, or minimize property damage; or
3) ACM was encountered that was not identified during the asbestos survey; or
4) The project must proceed to avoid imposing an unreasonable financial burden.
b. A notification shall be filed not later than the first working day after the asbestos project is commenced and must be accompanied by a written demonstration from the property owner or operator demonstrating the need for the emergency project.
H. ASBESTOS REMOVAL.
1. Renovation Projects. Except as provided in subsection 3.07I3 (pg. 3-xx), renovation work which does not remove ACM must:
a. Enclose or encapsulate the ACM in place; or
b. Leave the ACM in an unaltered and stable condition.
2. Demolition Projects. Except as provided in this subsection and subsection 3.07J3 (pg. 3-xx), work that could disturb ACM must not be done without first removing all ACM.
3. Exceptions. ACM need not be removed prior to demolition, if the property owner demonstrates that it is not accessible because of unsafe conditions. Examples and requirements for this are:
a. Facilities or vessels that are structurally unsound and in danger of imminent collapse, or
b. Other conditions that are immediately dangerous to life and health.
c. Documentation for Unsafe Conditions.
1) Submit written documentation of the hazard by a qualified government official or a licensed structural engineer, and
2) Submit procedures that will be followed for controlling emissions during demolition and disposal of the ACM.
I. PROCEDURES FOR ASBESTOS PROJECTS.
1. Training Requirements. Work must be performed by persons trained and certified in accordance with the standards established by L&I, OSHA, or EPA and whose certification is current. This requirement does not apply to asbestos projects conducted in an owner-occupied, single-family residence performed by the resident owner.
2. Asbestos Removal Work Practices. Persons (App. A) removing any ACM must:
a. Conduct work in a controlled area, marked by barriers and asbestos warning signs;
b. Restrict access to authorized personnel;
c. Equip with transparent viewing ports when a negative pressure enclosure is used, if feasible;
d. Saturate absorbent materials with a liquid wetting agent prior to removal;
e. Wet unsaturated surfaces exposed during removal immediately;
f. Coat nonabsorbent materials continuously with a liquid wetting agent;
g. Wet and seal all ACM waste (*) in leak-tight containers as soon as possible after removal but no later than the end of each work shift;
h. Clean any asbestos residue from the exterior of all leak-tight containers and ensure that each container is labeled with an asbestos warning sign specified by L&I, OSHA, or EPA;
i. Immediately after sealing each leak-tight container, permanently mark the container with:
1) Date the material was collected for disposal;
2) Name of the waste generator; and
3) Address where the ACM waste was generated.
This marking must be readable without opening the container;
j. Do not drop, throw, slide, or otherwise damage ACM waste containers; and
k. Store the ACM waste containers in a controlled area if not immediately transported to an approved waste disposal site.
3. Removal of Nonfriable ACM. The following asbestos removal methods must be employed for ACM that has been determined to be nonfriable (*) by a competent person (*) or an AHERA building inspector:
a. The material must be removed using methods which do not render the material friable. Removal methods such as sawing or grinding must not be employed.
b. Dust control methods must be used as necessary to assure no fugitive dust is generated.
c. The material must be carefully lowered to the ground to prevent fugitive dust.
d. After being lowered to the ground, the material must be immediately transferred to a disposal container.
4. Removal of Friable ACM. Any combination of the following are acceptable work practices:
a. Negative Pressure Enclosure. ACM removal is done inside a negative pressure enclosure equipped with a local exhaust system that captures airborne asbestos fibers;
b. Glove Bagging. ACM removal of small quantities of ACM using a glove bag (*) system.
c. Wrap and Cut Procedures. ACM need not be removed from a component (*) if the component is wrapped and sealed prior to removal, removed, stored for reuse or disposal, or transported without disturbing or damaging the ACM.
J. ALTERNATE MEANS OF COMPLIANCE. An alternate asbestos removal method may be used after prior written approval from the APCO if the following actions are taken:
1. Friable ACM Removal.
a. An AHERA project designer has evaluated the work area, the type of ACM, proposed work practices and engineering controls, and demonstrates to the APCO that the planned control method will be equally as effective as the work practices contained in subsection 3.07I (pg. 3-xx); and
b. The property owner or operator prepares a written air monitoring plan which includes PCM (App. B) air sampling. The sampling must demonstrate the asbestos fiber concentrations outside the controlled area do not exceed 0.01 f/cc (App. B) for an 8 hr. time weighted average.
c. Dry removal may be approved if:
1) It is necessary to avoid danger to workers or damage to equipment from wetting agents contacting high temperature steam lines or electrical components which can not be disconnected or de-energized during abatement, and
2) All wet removal methods have been evaluated by an AHERA project designer.
2. Nonfriable ACM.
a. A competent person or AHERA project designer has evaluated the work area, the type of ACM, the proposed work practices, and the engineering controls; and
b. The planned control method will be equally as effective as the work practices contained in subsection 3.07I (pg. 3-xx) in controlling asbestos emissions.
3. Leaving Nonfriable ACM in Place. Nonfriable ACM may be left in place during renovation or demolition upon prior written approval by the APCO if:
a. An AHERA project designer has evaluated the work area, the type of ACM, the proposed work practices, and the engineering controls; and
b. The ACM will remain nonfriable during all renovation or demolition activities and subsequent disposal of the debris.
c. This subsection does not apply to demolition by intentional burning.
4. Approval of Alternate Methods.
a. The APCO will issue an order of approval requiring conditions that are reasonably necessary to assure the planned control method is as effective as the work practices in subsection 3.07I (pg. 3-xx).
b. The APCO may revoke the order of approval for cause.
K. DISPOSAL OF ACM WASTE.
1. Prohibition. It is unlawful for any person to dispose of ACM waste unless it is deposited within ten days of removal at an approved waste disposal site.
2. Waste Tracking Requirements. It is unlawful for any person to dispose of ACM waste unless all of the following requirements are met:
a. Maintain shipment records starting prior to shipping the waste;
b. Use a form that includes all of the following information:
1) The name, address, and telephone number of the waste generator;
2) The approximate quantity in cubic meters or cubic yards;
3) The name and telephone number of the disposal site operator;
4) The name and physical location of the disposal site;
5) The date transported;
6) The name, address, and telephone number of the transporter; and
7) A certification that the contents of the consignment are fully and accurately described by proper shipping name and are classified, packed, marked, and labeled, and are in all respects in proper condition to transport by highway according to applicable waste transport regulations.
c. Provide a copy of the waste shipment record to the disposal site owner or operator at the same time the ACM waste is delivered.
d. Return a signed copy of the waste shipment record to the waste generator within 30 days after receiving the waste at the disposal site.
e. Retain a copy of all waste shipment records for at least 2 years, including a copy of the waste shipment record signed by the owner or operator of the designated waste disposal site.
3. Temporary Storage Site. A person may establish a facility to collect and store ACM waste if the facility is approved by the APCO and the following conditions are met:
a. Accumulated ACM waste is kept in a controlled storage area posted with asbestos warning signs and is accessible only to authorized persons;
b. Stored in leak-tight containers which are maintained in leak-tight condition;
c. Stored in a locked area except during transfer of ACM waste; and
d. Storage, transportation, disposal, and return of the waste shipment record to the waste generator must not exceed 90 days
L. FEES. See current fee schedule for the notification fees.
3.08 SPECIFIC DUST CONTROLS (New Section)
A. CONSTRUCTION DUST
1. Purpose. To prevent and reduce fugitive dust emissions from construction.
2. Applicability. Applies to any owner or operator engaged in the construction, repair, or demolition of any building; construction or maintenance of a road; site preparation; or landscaping work on a property.
3. Exemptions.
a. From Requirements in subsection 3.08A4 (pg. 3-xx). None.
b. From Submitting a Dust Control Plan.
1) A single family residence or duplex dwelling shall be exempt provided the site is not a phase of a project that involves more than one dwelling.
2) Projects causing complaints of dust emissions that result in a determination by the authority that reasonable precautions to prevent dust emissions are not being used shall not be exempt from the requirement for a dust control plan.
c. Emergencies. Sources are granted exemptions from subsection 3.08A during the following emergency situations provided the source contacts the authority within 24 hrs. of the start of the emergency and uses reasonable precautions as soon as feasible after the emergency is resolved:
1) Active operations conducted during emergency, life threatening situations, or in conjunction with an officially declared disaster or state of emergency; or
2) Active operations conducted by public service utilities to provide electrical, natural gas, telephone, water, or sewer service during emergency outages.
4. Requirements.
a. Visible Emissions. Sources are required to comply with subsection 3.01C1a (pg. 3-xx).
b. Preventing Particulate Matter From Becoming Airborne. Sources are required to comply with subsection 3.01C1b (pg. 3-xx).
c. Construction, Demolition, or Repair Work. Sources are required to comply with subsection 3.01C1c (pg. 3-xx).
d. Emissions Detrimental to Persons or Property. Sources are required to comply with subsection 3.01C1e (pg. 3-xx).
e. Fugitive Dust. Sources are required to comply with subsection 3.01C2c (pg. 3-xx).
f. Water for Dust Control. (5.12D) Any person engaged in
the doing construction, repair, remodeling or demolishing of any
building; or engaging in any road construction or repair within
any incorporated town or city in Yakima County, Washington, or
within an area of one (1) mile of the city limits of the city of
Yakima, Washington, or within one-quarter (1/4) of a mile of the
city limits of any other town or city in Yakima County,
Washington, shall take such measures as are reasonably necessary
to reduce air pollution, including the use of water and the
sprinkling of water to control dust so that the same is not
emitted and deposited upon the property of others in quantities
which unreasonably interfere with the enjoyment of their
property. No work as above defined shall be commenced without
having must have an adequate supply of water available at the job
site in sufficient quantities to control dust air pollution at
the time of commencement of such work. at all times.
g. Site or Project Dust Control Plans. Where the potential exists for fugitive dust emissions, an owner or operator must prepare a site dust control plan and submit it to the authority 15 days prior to the start of any work that will disturb soil stability, cover, or cause fugitive dust emissions.
1) Dust control plans must identify management practices and operational procedures which will effectively control fugitive dust emissions.
2) Dust control plans must contain the following information:
a) A detailed map or drawing of the site;
b) A description of the water source to be made available to the site, if any;
c) A description of preventive dust control measures to be implemented, specific to each area or process;
d) A description of contingency measures to be implemented in the event any of the preventive dust control measures become ineffective;
e) A statement, signed by the owner or operator of the site, accepting responsibility for the implementation and maintenance of the dust control plan;
f) The name and telephone number of person(s) available 24 hours a day to mitigate any episodes of dust emissions; and
g) If the ownership or control of all or part of the site changes, the plan must be resubmitted by the new party and approved by the authority.
3) The authority will review the plan and either approve or require modification of the plan.
4) An owner or operator must implement effective dust control measures outlined in approved plans.
h. Master Dust Control Plan. As an alternative to a site dust control plan, an owner or operator may submit a master dust control plan that applies to more than one site or project. The master plan must:
1) Address all the requirements in subsection 3.08A4g (pg. 3-xx); and
2) Provide for effective control of fugitive dust emissions to all sites and projects.
3) Prior to the commencement of work at any site or project covered by the master plan, additional notification must be submitted as soon as possible. The master plan or the additional notification must:
a) Give the name and phone number of a person responsible for the implementation of dust control measures for each of the sites; and
b) Address any unique site qualities or project operations that would impair the effectiveness of dust control measures.
5. Additional Information. Additional information is available from the authority.
6. Fees. See current fee schedule.
B. DUST FROM CATTLE FEEDING OPERATIONS.
1. Purpose. To prevent and reduce fugitive dust emissions from cattle feeding operations.
2. Applicability. Applies to any owner or operator of a beef or dairy replacement cattle feeding operation:
3. Exemptions. Sources are granted exemptions from subsection 3.08B during an emergency situations provided:
a. The owner or operator of the source contacts the authority before the end of the next business day after the start of the emergency; and
b. The source uses reasonable precautions as soon as feasible after the emergency is resolved.
c. An emergency situation exists when compliance with subsection 3.08B would cause risk to human health or substantial crop damage or cattle loses.
4. Requirements.
a. Visible Emissions. Sources are required to comply with subsection 3.01C1a (pg. 3-xx).
b. Preventing Particulate Matter From Becoming Airborne. Sources are required to comply with subsection 3.01C1b (pg. 3-xx).
c. Odor. Sources are required to comply with subsection 3.01C1d (pg. 3-xx).
d. Emissions Detrimental to Persons or Property. Sources are required to comply subsection 3.01C1e (pg. 3-xx).
e. Fugitive Dust. Sources are required to comply with subsection 3.01C2c (pg. 3-xx).
f. Dust Control Plan Preparation. The following types of sources must prepare and submit an annual dust control plan to the authority no later than April 15th of each year.
1) Any source with an average of 1,000 or more cattle confined and fed during the months of April through October and; or
2) Any cattle feeding operation which receives a verified fugitive dust complaint.
g. Dust Control Plan Content. Dust control plans must include:
1) A map or drawing of the feedlot;
2) The operational capacity of the feedlot;
3) The maximum number of cattle which are confined;
4) The water available to the feedlot for dust control;
5) The site-specific features which could complicate or prevent implementation of BMPs (App. B)
6) Which BMPs will be used, and where they will be used;
7) The equipment and materials to be used to implement a BMP;
8) An operational and maintenance plan and schedule to implement each BMP; and
9) An operation and maintenance plan which also includes BMPs for;
a) Hay chopping,
b) Grain processing,
c) Feed mixing, and
d) Feed handling.
h. Plan Implementation.
1) The authority will approve or require modification of the plan within 30 days of receipt.
2) A feedlot operator must implement an approved dust control plan.
3) A feedlot operator may change practices from those in an approved dust control plan as long as the effectiveness of the plan is not reduced, and the operator notifies the authority of the change.
4. Additional Information. Additional information is available from the authority.
5. Fees. See current fee schedule
3.09 MOBILE SOURCE EMISSIONS (New Section) Reserved for later use.
3.10 GENERAL RULE FOR MINOR SOURCES (New Section) Reserved for later use.
3.11 MONITORING, RECORDKEEPING, AND SPECIAL REPORTING (5.11)
A. PURPOSE. To ensure the authority has sufficient information to determine compliance with emission limitations, permit conditions, and control measures.
B. APPLICABILITY. To the owners or operators of air pollution sources upon notification by the authority or specified by federal or state law or regulation.
C. NOTIFICATION. Sources (App. A) are notified of the requirements for this section by any of the following:
1. NSR (App. B) approval orders;
2. Requirements imposed by an AOP (App. B);
3. Regulatory orders issued by the APCO (App. B);
4. Compliance orders or corrective action orders issued by the APCO; or
5. Required by the APCO.
D. GENERAL REQUIREMENTS.
1. Emission Standards and Test. The measurable emission standards cited in section 3.11 are listed in app. D (pg. D-1) with the test method and compliance assurance requirements.
2. Installation of Monitoring Equipment. Categories of sources or individual sources may be required by federal or state law or regulations or directed by the APCO to install, operate, and maintain equipment to monitor air pollutants for just cause.
3. Excess Emissions. (5.11D & WAC 173-400-107) If an
equipment breakdown or upset condition occurs resulting in
emissions in excess of applicable limits set by this Regulation
or resulting in emissions which violate an applicable compliance
schedule, the owner or operator of the affected source shall take
immediate corrective action and shall report such breakdown to
the Authority by the next working day after the breakdown occurs.
An initial breakdown or upset condition shall not be subject to
penalties for emissions in excess of the limits set by this
chapter, providing the owner or operator complies with the
provisions of this subsection and providing the breakdown or
upset was not the result of gross negligence. If an extended
time period is required to complete the corrective action, the
Authority or its authorized representative may require that the
operation be curtailed or shutdown. Repeated breakdowns may be
subject to all penalties authorized by law. The Authority or its
authorized representative may issue regulatory orders specifying
maintenance and operating procedures. The owner or operator of a
source must take the following actions and prove to the authority
that excess emissions were unavoidable to obtain relief from
enforcement action under article 5.
a. Immediate Action for All Excess Emissions. Take immediate corrective action to stop the excess emissions and mitigate the effects. This includes slowing or stopping the emission units when the operator knows or should have known a standard or permit condition was exceeded.
b. Reporting Action. Report the excess emissions to the authority as follows:
1) All excess emissions which present a risk to public health or safety or the owner or operator believes are unavoidable shall be reported by the end of the next working day;
2) All other excess emissions by the end of the following month during the submission of emission monitoring reports or by a special report; and
3) When requested by the authority, the owner or operator shall submit a detailed written report which addresses the following:
a) Known causes of the emissions;
b) Corrective action taken;
c) Preventive measures taken to minimize the risk of a reoccurrence;
d) A demonstration that the excess emissions could not be avoided through better planning and design of the equipment and processes;
e) Any bypass of control apparatus (App. A) which was necessary to prevent the loss of life, personal injury, or severe property damage;
f) The excess emissions could not have been avoided by a different scheduling for maintenance or operation and maintenance practices; and
g) The excess emissions were not the result of a reoccurring pattern which indicates inadequate design, operation, or maintenance of the equipment or processes.
c. Determination of Unavoidable Excess Emissions. After receiving the reports from the source, the authority shall make a determination of whether the excess emissions were avoidable or unavoidable. Unavoidable excess emissions must meet all of the following conditions:
1) The source took immediate action to stop the excess emissions and mitigate the effects;
2) The source reported the excess emissions as required; and
3) The excess emissions resulted during any of the following:
a) Equipment startup or shut down;
b) Scheduled maintenance and the excess emissions could not be avoided by reasonable design, better scheduling of the maintenance, or better operation and maintenance practices;
c) Upset conditions not caused by poor or inadequate design, operation, or maintenance; or
d) Upset conditions caused by power failure or other natural causes.
Any other excess emissions are considered avoidable.
d. Action by the Authority.
1) Shall make a determination of avoidable or unavoidable excess emission within 30 days after all information has been submitted by the owner or operator of the source.
2) If the excess emissions are found to be avoidable, the authority shall take appropriate enforcement action.
3) May require shutdown of the equipment or process if the corrective action will require an extended time period
4. Change in Raw Material or Fuels for Non-AOP Sources. (5.11K)
a. Any change or series of changes in raw material or fuel
which will result in a cumulative increase in emissions of any of
the following air pollutants sulfur dioxide of forty 40 tons per
year or more over that stated in the initial inventory required
by WAC 173-400-105(1) shall require the submittal of sufficient
information to Ecology or the authority to determine the effect
of the increase upon ambient concentrations of sulfur dioxide the
pollutant:
1) SO2 - 40 TPY (App. B)
2) NOx - 40 TPY
3) VOCs - 40 TPY, or
4) PM - 25 TPY.
b. Ecology or The authority may issue regulatory orders
requiring controls to reduce the effect of such the increases.
c. Cumulative changes in raw material or fuel of less than
0.5 percent increase in average annual sulfur content over the
initial inventory may not require such a notice.
5. Maintenance of Monitoring Records. The source shall maintain monitoring records at the source for the following time periods:
a. Minor Sources. Two years unless directed otherwise by the APCO.
b. Major Sources. Five years.
6. Additional Monitoring Requirement. Nothing in this section precludes the authority from requiring additional monitoring, recordkeeping, reporting, or compliance assurance monitoring.
E. EMISSIONS SAMPLING.
1. Ambient Air Monitoring. (5.11 A)
a. Purpose. The Authority shall conduct a continuous
surveillance program To monitor the quality of the ambient
atmosphere as to for the concentrations and movements of air
contaminants pollutants as approved_by the Board.
b. Monitoring. As part of this program, The Authority APCO
(App. B) or its authorized representative may require any source
under the jurisdiction of the Authority to conduct stack and/or
ambient air monitoring, and to report the results to the
Authority when there is credible evidence that the source is
creating significant emissions that contributes to a violation of
the NAAQS (App. B).
c. Quality Control. The monitoring equipment shall be operated and maintained to meet the QA/QC (App. B) requirements of 40 CFR Part 58.
d. Reporting Requirements. The reporting requirements and due date for the reports will be specified by the APCO.
2. Compliance Testing. (5.11 C) In order to demonstrate
compliance with this Regulation, the Authority or its authorized
representative may require that a test be conducted of the source
using approved EPA methods from 40 CFR 60 Appendix A on file at
the Authority or Ecology.
a. Purpose. To determine source compliance with the appropriate emission standards.
b. Sampling Requirements.
1) Test Methods. Must be a test be conducted of the source
using applicable approved EPA methods from 40 CFR Part 51, 60,
61, or 63 Appendix A, on file at the Authority or Ecology and
"Source Test Manual - Procedures for Compliance Testing", WA
State Dep't. Of Ecology, July 12, 1990.
2) Testing Frequency. Sources having one or more emission points which emit more than a significant amount of any pollutant as defined in app. A will be tested for compliance with the applicable standards at least:
a) Major Stationary Sources. Once per five years or as required by NSR approval, permit, order, or state or federal requirements.
b) Minor Sources. As required by NSR approval, permit, order, or state or federal requirements.
3) Sample Collection by the Authority. The operator of a
source may be required to provide the necessary platform and
sampling ports to perform a test of the source. The Authority
shall be allowed to obtain a sample from any source. The
operator of the source shall be given an opportunity to observe
the sampling and to obtain a sample at any time. As specified in
subsection 2.01D (pg. 2-xx).
4) Sample Collection by the Owner or Operator. The owner or operator of a source shall notify the authority in writing at least 14 days prior to any compliance test and provide the authority an opportunity to review the test plan and observe the test.
c. Test Results. The owner or operator of any source required to perform a compliance test must submit a report to the authority no later than 60 days after the test. The report must include:
1) A description of the source and the sampling location;
2) The time and date of the test;
3) A summary of results, reported in units and for averaging periods consistent with the applicable emission standard;
4) A description of the test methods and quality assurance procedures employed;
5) The amount and type of fuel burned or raw material processed by the source during the test;
6) The operating parameters of the source and control apparatus (App. A) during the test;
7) Field data and example calculations; and
8) A statement signed by the senior management official of the testing firm certifying the validity of the source test report.
d. Required by the Authority. As a condition of a NSR (App. B) approval, a permit, regulatory order, or order of approval, the authority may require the source to provide a compliance test.
3. Emission Inventory. (5.11 J)
a. Purpose. To maintain a current and accurate inventory of emissions from air pollution sources.
b. Applicability. The owner(s) or operator(s) of any air
contaminant of the following types of sources shall must submit
an annual inventory of emissions from the source each year.:
1) Major stationary sources;
2) Sources emitting significant levels of pollutants as listed in app. A;
3) Sources subject to 40 CFR Part 60, NSPS (App. B); 40 CFR Part 61, NESHAPS (App. B); or 40 CFR Part 63, MACT (App. B); or
4) Any source required by NSR approval, permit, order, or state or federal requirements.
c. Specific Requirements.
1) Emissions Included. The inventory may include stack and
fugitive emissions of particulate matter, PM-10, sulfur dioxide,
carbon monoxide, total reduced sulfur compounds (TRS), fluorides,
lead, VOCs, and other contaminants, and shall be submitted (when
required) no later than one hundred five (105) days after the end
of the calendar year., The owner(s) or operator(s) shall
maintain records of information necessary to substantiate any
reported emissions, consistent with the averaging times for the
applicable standards. The inventory shall include the emissions
from all emission units for criteria pollutants (App. A),
fluorides, TRS (App. B), and TAPS (App. B) listed in app. K, para
B (pg. K-4).
2) Records Maintenance. The owner(s) or operator(s) shall
must maintain records of information necessary to substantiate
any reported emissions consistent with the averaging times for
the applicable standards.
3) Due Date. and shall The inventory must be submitted
(when required) no later than one hundred five (105) days after
the end of the calendar April 1st of each year or as directed by
the APCO.
4) Review by the Authority. Emission inventories are subject to review and approval by the authority. Emission inventories which are incomplete or inaccurate shall be returned to the source for correction and resubmission to the authority.
F. CONTINUOUS MONITORING AND RECORDING REQUIREMENTS FOR CERTAIN SOURCES. (5.11 E)
1. Purpose. (5.11A) The Authority shall conduct a
continuous surveillance program to monitor the quality of the
ambient atmosphere as to concentrations of air contaminants as
approved by the Board.
As part of this program, the Authority or its authorized representative may require any source under the jurisdiction of the Authority to conduct stack and/or ambient air monitoring, and to report the results to the Authority. To continuously monitor the emissions and ambient air conditions at certain sources for specific pollutants.
2. Applicability. Applies to the categories of stationary sources and the emissions specified in table 3.11-1.
3. Specific Requirements.
a. Monitoring Equipment. Prior to the start of emitting air
pollutants from a source, owners and operators of the following
categories of stationary sources listed must install, calibrate,
maintain, and operate equipment for continuously monitoring and
recording equipment those emissions specified for:
1) Sources categories in table 3.11-1; or
2) Sources or source categories directed by the APCO.
b. Waiver or Extensions. (5.11 F) All sources subject to
this Regulation shall procure and install equipment and commence
monitoring and recording activities. no later than eighteen (18)
months after adoption of this Regulation by the Authority. Any
waiver or extension to this time requirement shall must be
requested as a negotiated through the variance procedure of . WAC 173-400-180 under subsection 3.00D (pg. 3-xx).
4. Exemptions. (5.11H) Are listed in table 3.11-2.
a. A source subject to a New Source Performance Standard;
b. A source not subject to an applicable emission standard;
5. Equipment and Performance Specifications. (5.11 E. 5)
Owners and operators of those sources required to install
continuous monitoring equipment under this regulation or the SIP
(App. B) shall must demonstrate to the Authority compliance with
the equipment and performance specifications, and observe the
reporting requirements, contained in:
a. Title 40 Code of Federal Regulations, CFR Part 51 (App.
B), Appendix P, Section 3, 4, and 5, promulgated on October 6,
1975, which is by this reference adopted and incorporated herein;
b. 40 CFR Part 60, App. B, Performance Specifications; and
c. QA/QC requirements in 40 CFR Part 60, App. F.
6. Special Considerations. (5.11 G)
a. If for reason of physical plant limitations or extreme economic situations, the authority determines that continuous monitoring is not a reasonable requirement, alternative monitoring and reporting procedures will be established on an individual basis.
b. These will generally be of the form of stack (App. A)
tests conducted at a frequency sufficient to establish the
emission levels over time and to monitor the variability of the
emissions deviations in these levels.
7. Monitoring System Malfunctions. (5.11 I)
a. A source may be temporarily exempted from the monitoring
and reporting requirements of this Regulation during periods of
when the monitoring system malfunctions provided that the source
owner or operator shows demonstrates in writing to the
satisfaction of the authority that the real malfunction was
unavoidable and is being repaired as expeditiously as
practicable.
b. Missing monitoring system data is acceptable when:
1) The missing data is ≤ 10% of the total observations;
2) The missing data is not continuous; and
3) The missing data resulted from monitoring equipment malfunction, calibration, maintenance, power failure, or other conditions not reasonably preventable.
Table 3.11-1 Source Categories which Require Continuous Emissions Monitoring.
Stationary Source Category | Emission to be Monitored |
Fossil fuel-fired steam generators | Opacity |
Sulfur dioxide (SO2) | |
% O2 or CO2 |
|
Sulfuric acid plants | SO2 where production capacity is > 300 tons/day, expressed as 100% acid |
Fluid bed catalytic cracking units catalyst regenerators at petroleum refineries | Opacity |
Wood residue fuel-fired steam generators. | Opacity. See exemption in table 3.11-2. |
Table 3.11-2 Source Categories Exempt from Continuous Emissions Monitoring.
Stationary Source Category | Exemptions to Monitoring Requirement | |
Fossil fuel-fired steam generators | Steam generator capacity < 250 million BTU/hr heat input (App. B) | General exception. These requirements do not apply to a fossil fuel-fired steam generator with an annual average capacity factor of less than 30% as reported to the Federal Power Commission for the calendar year 1974, or as otherwise demonstrated to the authority by the owner or operator. |
Only gaseous fuel is burned | ||
Steam generator capacity < 250 million BTU/hr heat input | ||
SO2 (App. B) control apparatus is not required | ||
If such measurements are not necessary for the conversion of SO2 continuous emission monitoring data | ||
Sulfuric acid plants | Facilities where conversion to sulfuric acid is |
|
Fluid bed catalytic cracking units catalyst regenerators at petroleum refineries | Fresh feed capacity < 20,000 barrels/day (App. B).. | |
Wood residue fuel-fired steam generators. | Steam generator capacity < 100 million BTU/hr heat input. | |
When the control apparatus causes the exhaust plume to be water vapor that prevents a correct opacity reading. |
4.00 REQUIREMENTS COMMON TO ALL PERMITS (New Section) Reserved for later use.
4.01 REGISTRATION PROGRAM (4.01)
A. PURPOSE. (WAC 173-400-099) To develop and maintain a current and accurate record of air contaminant sources.
B. APPLICABILITY. (4.01 A) Applies to the owner or operator
of each source within the following source categories in app. G.
(pg. G-1), that does not hold an operating permit, shall
register the source with the Authority:
C. RESPONSIBILITY. (4.01D) The owner or operator of the source is responsible to notify the authority of the existence of the source except when exempted in subsection 4.01D (pg. 4-1).
D. EXEMPTIONS. All exemptions based on emissions use the actual emissions from the source.
1. Air Operating Permit Sources. Sources or emission units which are permitted according to section 4.04 (pg. 4-xx).
2. Criteria Exempt Sources. Sources which have actual emissions less than the rates shown in table 4.01-1 (pg. 4-1).
3. Toxic Air Pollutant Sources. Sources which do not emit a quantifiable amount of toxic air pollutants listed in app. K, para. B.
4. Gasoline Marketing Operations.
a. Any loading terminal or bulk plant dispensing ≤ 7,200,000 gallons per year;
b. Any gasoline dispensing facility dispensing ≤ 360,000 gallons per year which started operation prior to August 31, 1991; or
c. Any gasoline dispensing facility with a total storage capacity of ≤ 10,000 gallons.
Pollutant | TPY (App. B) | |
CO (App. B) | 5.0 | |
NOx (App. B) | 2.0 | |
SO2 (App. B) | 2.0 | |
PM (App. A) | 1.25 | |
PM10 (App. A) | 0.75 | |
VOC (App. B) | 2.0 | |
Pb (App. B) | 0.005 |
1. A grain warehouse or elevator emission source with an annual volume of < 10,000,000 bushels is granted an exemption from registering, reporting, or paying a registration fee after:
a. Filing an initial registration according to subsection 4.01F1 (pg. 4-xx);
b. Filing an Initial report according to subsection 4.01F2 (pg. 4-xx); and
c. Paying the initial registration fee according to subsection 4.01G (pg. 4-xx).
2. The exemption remains until the source increases the licensed capacity.
3. If the licensed capacity is increased, the source must register, report, and pay the registration fee again prior to the start of the first harvest season after the date of change in the licensed capacity.
4. The source is not exempted from the requirements of 4.01F5&6 (pg. 4-xx).
F. REGISTRATION AND REPORTING PROCEDURE. (WAC 173-400-101, 102, & 103)
1. Registration. (4.01E) The owner or operator of any
proposed new source shall register the source with the Authority.
Initial registration and reporting shall be on forms supplied by
the Authority within the time specified thereon.
a. Sources required to register are defined in subsections 4.01B, D, & E (pg. 4-xx).
b. The registrant shall use forms and directions supplied by the authority.
c. The forms must be completed and returned within the time
specified. The forms will provide for the submission of
information concerning locations, size and height of contaminant
outlets, processes employed, nature of the contaminant emission
and such other information relevant to air pollution as the
Authority may require. A separate registration shall be required
for each source of contaminant provided that an owner or lessee
has the option to register a process with a detailed inventory of
contaminant sources and emissions related to said process and
provided further than an owner need not make a separate
registration for identical units or equipment or control
apparatus installed, altered or operated in an identical manner
on the same premises.
d. (4.01 F) Emission units within the facility must be listed separately unless they meet the following conditions:
1) The authority determines that certain emission units may be combined into process streams for purposes of registration and reporting; or
2) There are identical units of equipment or control facilities installed, altered, or operated in an identical manner on the same process; the number of the units may be reported.
2. Reporting. (4.01 E) After initial registration and
reporting, subsequent general Reports shall must be filed
annually during January on using forms and directions supplied by
the authority in accordance with the terms of the Pollution
Disclosure Act of 1971, Chapter 160, Laws of 1971, Extraordinary
Session.
a. Detailed Annual Reporting.
1) The source emits one or more pollutants at rates greater than those listed in table 4.01-2;
2) Reporting is necessary to comply with federal requirements and emission standards;
3) Reporting is required in a RACT (App. B) determination for the source category;
4) The APCO determines that the source poses a threat to human health and the environment; or
5) Sources who qualified for three-year reporting, but failed to comply with the regulations or orders issued by the authority.
b. Three-Year Reporting.
1) The source emits one or more pollutants at rates greater than the rates in table 4.01-1 but less than the rates in table 4.01-2; or
2) The source emits a quantifiable amount of one or more class A or B toxic air pollutants listed in app. K, para. B (pg. K-4).
Table 4.01-2 Significant Pollutant Emission Levels
Pollutant | TPY | |
CO (App. B) | 100 | |
NOx (App. B) | 40 | |
SOx (App. B) | 40 | |
PM (App. A) | 25 | |
PM10 (App. A) | 15 | |
VOC (App. B) | 40 | |
Pb (App. B) | 0.6 | |
Fluorides | 3 | |
H2SO4 (App. B) mist | 7 | |
H2S (App. B) | 10 | |
TRS (App. B) including H2S | 10 | |
Municipal waste combustor organics measured as total tetra-through octa-chlorinated dibenzo-p-dioxins and dibenzofurans. | .0000035 | |
Municipal waste combustor metals measured as PM. | 15 | |
Municipal waste combustor acid gases measured as SO2 and HCl (App. B) | 40 |
1) Detailed annual reports shall contain:
a) Annual emissions inventory;
b) Operation and maintenance plans;
c) Plan showing the plant layout; and
d) Changes in operations since the last detailed report.
2) Three-year reports shall contain the annual emissions inventories.
3) The APCO (App. B) will schedule the detailed annual and three-year report cycles.
3. Operational and Maintenance Plan. Owners or operators of registered air contaminant sources must develop and maintain an operation and maintenance plan for process and control apparatus (App. A). The plan must:
a. Reflect good industrial practice;
b. Include a record of performance and periodic inspections of process and control apparatus;
c. Be reviewed and updated by the source owner or operator at least annually; and
d. Be made available to the authority upon request.
4. Signature. (4.01G) Each registration shall be signed by
the owner or lessee or agent for such owner or lessee. The owner
or the lessee of the source shall be responsible for the
registration and the correctness of the information submitted.
The owner, operator, or a designated representative must sign the
registration or reporting form for each source. The owner or
lessee of the source is responsible for the accuracy,
completeness, and timely submittal of this information.
5. Closure Report. (4.01 B) A special closure report of
closure shall must be filed with the authority within 90 days
whenever the operations producing of an emissions source is are
permanently ceased for any source listed in Section 4.01(A)
above.
6. Change of Ownership. A new owner or operator must report to the authority within 90 days of any change of ownership or operator.
G. FEES. (4.01 H) All registrants shall must pay a fee in
accordance with the registration current fee schedule in Article
XIII, Section 13.01.
4.02 NOTICE OF CONSTRUCTION NEW SOURCE REVIEW. (4.02, RCW 70.94.152, & WAC 173-400-110->116)
A. PURPOSE. To explain the requirements and processes for a new source review (NSR) application for a stationary or temporary source and the resulting review and approval process.
B. APPLICABILITY. (4.02A) No person shall construct, install,
establish, or modify a new air contaminant source, except those
sources excluded in Section 4.03 of this Regulation, without
first filing with the Authority a "Notice of Construction,
Installation or Establishment of New Air Contaminant Source", on
forms prepared and furnished by the Authority. For the purpose
of this section, addition to or enlargement or replacement of an
air contaminant source, or any major alteration therein, shall be
construed as construction, installation or establishment of a new
air contaminant source.
1. Applies to all temporary sources and the following stationary sources unless exempted in subsection 4.02C (pg. 4-xx):
a. All new air pollution sources;
b. Any replacement or alteration of air emission control apparatus (App. A) or a change in process that affects emissions;
c. Any project that qualifies as a construction, reconstruction, or modification of a facility within the meaning of 40 CFR Part 60 except Subpart AAA, Woodstoves;
d. Any project that qualifies as a new or modified source within the meaning of 40 CFR 61.02 except for asbestos demolition and renovation projects subject to 40 CFR 61.145;
e. Any project that qualifies as a new source within the meaning of 40 CFR 63.2;
f. Any project that qualifies as a major stationary source or major modification of a source as defined in app. A; or
g. Any project that requires an increase in a plant-wide cap or unit specific emission limit.
2. Any source emitting toxic air pollutants (TAP).
a. The NSR (App. B) for the TAP (App. B) is subject to chap. 173-460 WAC; and
b. The NSR for all other pollutants is subject to this section.
3. The NSR for all air pollutants may be combined in one application and approval.
C. EXEMPTIONS. (4.03) Neither registration nor notice of
construction shall be required for the following air contaminant
sources:
1. Air conditioning or ventilating systems not designed to remove contaminant generated by or released from equipment.
2. Blast cleaning equipment which uses a suspension of abrasive in liquid water.
3. Fuel burning equipment if used solely for a private dwelling serving three (3) families or less.
4. Insecticide and herbicide spray equipment.
5. Non-stationary internal combustion engines, including gas turbine and jet engines.
6. Laboratory equipment used exclusively for chemical or physical analysis.
7. Laundry driers, extractors or tumblers used exclusively for the removal of water from fabric.
8. Application of surface coatings by use of an aqueous solution or suspension if used on external or internal walls of residential, commercial or industrial facilities.
9. Steam cleaning equipment used exclusively for that purpose.
10. Vacuum producing devices used in laboratory operations, and vacuum producing devices which do not remove or convey air contaminant from or to another source.
11. Vents used exclusively for:
c. Sanitary or storm drainage systems;
d. Safety valves; or
e. Washing or drying equipment used for products fabricated from metal or glass, if no volatile organic material is used in the process.
f. Construction of single family or duplex dwellings.
1. Emission Unit and Activity Exemptions. These are listed in app. K, para. A (pg. K-1).
2. Exemptions Based on Emissions Thresholds.
a. A new emissions unit with a potential to emit below each of the threshold levels (App. A) listed in table 4.02-1 is exempt from NSR provided the conditions of subsection 4.02C2c (pg. 4-xx) are met.
b. A modification to an existing emissions unit that increases the unit's actual emissions by less than each of the threshold levels listed in the table 4.02-1 is exempt from NSR provided the conditions of 4.02C2c (pg. 4-xx) of this subsection are met.
c. The owner or operator seeking to exempt a project from NSR shall notify, and upon request, file a brief project summary with the authority prior to beginning actual construction on the project. If the authority determines that the project will have more than a de minimis (App. A) impact on air quality, the authority may require the filing of a NSR application. The authority may require the owner or operator to demonstrate that the emissions increase from the new emissions unit is smaller than all of the thresholds listed in table 4.02-1
d. The owner/operator may begin actual construction on the project 31 days after the authority receives the project summary, unless the authority notifies the owner/operator within 30 days that the proposed new source requires a NSR application.
Table 4.02-1 Exemption Threshold Table
Pollutant | Threshold Level TPY (App. B) |
PM (App. A) | 1.250 |
PM10 (App. A) | 0.750 |
SOx (App. B) | 2.000 |
NOx (App. B) | 2.000 |
Total VOC (App. B) | 2.000 |
CO (App. B) | 5.000 |
Pb (App. B) | 0.005 |
Ozone Depleting Substances in Aggregate (the sum of Class I and/or Class II substances as defined in FCAA Title VI and 40 CFR Part 82) |
1.000 |
Toxic Air Pollutants | As specified in 173-460 WAC & app. K, ¶ B. |
D. REQUIREMENTS FOR ALL NSR APPLICATIONS.
1. Information Required.
a. Application Form. The source must use and complete the NSR application on forms furnished by the authority.
b. Additional Documentation. Any additional information required by the APCO (App. A) to show that the proposed air contaminant (App. A) source will meet the applicable emissions standards.
c. Signature. (SCAPCA Sect 5.04) Each NSR application must be signed by the owner, operator, or designated representative of the air contaminant source.
2. Public Involvement. (4.02 H2) Within fifteen days of
receipt of a complete application for a Notice of Construction
the Authority shall determine whether public notice is required.
, and if so it shall publish notice to the public of an
opportunity to submit written comments during a thirty (30) day
period The authority must follow the requirements of section 2.04
(pg. 2-xx).
3. Limitation of Review. (4.02 D) Any Notice of Construction
review of a modification shall will be limited to the emission
unit(s) or units proposed to be modified and the air contaminants
pollutants whose emissions would increase as the result of the
modification described in the NSR application after the
completeness determination is made under subsection 4.02E.
4. Operation and Maintenance. (4.02 D) Any features,
machines and devices constituting parts of or called for by
plans, specifications or other information submitted pursuant to
this section shall be maintained and operated in good working
order. The owner or operator will operate and maintain the
process and control apparatus subject to the NSR application
according to the specifications of the manufacturer and
subsection 3.00E (pg. 3-xx) to prevent avoidable emissions.
E. ADDITIONAL NSR APPLICATION REQUIREMENTS FOR STATIONARY SOURCES.
1. Time Limits.
a. Completeness Determination. (4.02B) Within thirty (30)
days after the receipt of Notice of Construction the NSR
application the authority shall must either notify the applicant
in writing that additional information is necessary; or that the
application is complete.
b. Additional Information is Needed. The Authority may
require the submission of plans, specifications, and such other
information as it deems necessary concerning the proposed
construction, installation and establishment of such source.
After the request for additional information, the applicant must
provide the requested information within 30 days; or within 15
days provide a date when the information will be available.
2. Cancellation of Application. An application that doesn't meet these time limits may be canceled. Any continuation shall require a new NSR application.
3. Withdrawal of Application. An applicant may withdraw an application at any time.
4. Action on Application. (4.02C) Within sixty (60) days of
receipt by the authority of a complete Notice of Construction NSR
application the authority shall must either:
a. Initiate public notice and comment on a proposed decision
for those Notice of Construction application reviews subject to
public notice and issue thereafter a final decision as promptly
as possible projects qualifying under section 2.04 (pg. 2-xx); or
b. Issue a final decision on the application.
F. ADDITIONAL NSR APPLICATION REQUIREMENTS FOR TEMPORARY SOURCES.
1. Advance Notification. (4.02G) For Sources, such as
asphalt batch plants, with multiple locations which are located
temporarily at particular multiple sites, the owner or operator
shall be permitted to relocate and operate at a temporary
location without filing a notice of construction providing that
after the owner or operator must provides the following
notification to the authority of the intent to operate at the new
location. This notification must be at least thirty (30) days
prior to starting the operation.
2. Information Required. and The source must suppliesy
sufficient information to enable the authority to determine that
the operation will comply with:
a. The emission standards for a new source;
b. and The applicable ambient air standards; and
c. If in a non-attainment area, it will not interfere with scheduled attainment of ambient standards.
G. REQUIREMENTS FOR THE APPROVAL OF ALL NSR APPLICATIONS.
1. SEPA Compliance. No NSR application will be approved without complying with the SEPA (App. B) and public participation requirements in section 2.04 (pg. 2-xx).
2. Content. An approved NSR must include the following:
a. (4.02D2) Include A determination of whether that the
operation of the new air contaminant source at the location
proposed location will not cause any ambient air quality standard
to be exceeded or cause a potential hazard to public health.
b. (4.02 D2) Include A determination that the proposed new
source will comply with all applicable new source performance
standards and National Emission Standards for Hazardous Air
Pollutants federal, state, and authority laws and regulations.
This includes the visibility protection requirements in
nonattainment areas in 40 CFR 52.28.
c. (4.02E) A determination of which emission control devices will be used.
d. For an existing stationary source when the emission
control technology is replaced or substantially altered, but does
not constitute a major modification, Best Available Control
technology (BACT) and Reasonable operation and maintenance
conditions procedures for the process and control apparatus may
be are required by the Authority.
e. Minor Sources in Nonattainment Areas. For New or
modifications of minor sources (App. A) in nonattainment areas
must use BACT (App. B) for all air pollutants. Best Available
Control technology (BACT) will be employed, except that if.
f. Major Stationary Sources and Major Modifications (App. A) in Nonattainment Areas.
1) The new source is a major stationary source; or the
proposed modification is a major modification it will achieve the
LAER for the contaminants for which the area has been designated
nonattainment. Must use LAER (App. B) for the pollutant(s) for
which the area has been designated non-attainment; and
2) Must use BACT for all other pollutants.
g. New All Sources in Attainment or Unclassifiable Areas.
1) For new sources in attainment or nonclassifiable areas.
Best Available Control technology (BACT) will be employed for all
pollutants not previously emitted or whose emissions would
increase as a result of the new source or modification must be
used for all pollutants subject to a NSR.
2) Emissions from new or modified sources must not affect the attainment status or contribute to a NAAQS (App. B) violation in a downwind nonattainment area. This requirement is met if the emissions from the source do not exceed the threshold levels in table 4.02-2.
Table 4.02-2, Threshold Emission Levels for New or Modified Sources Upwind from Nonattainment Areas
Pollutant | Maximum Emission Rates | ||||
Annual Average |
24 Hour Average |
8 Hour Average |
3 Hour Average |
1 Hour Average |
|
CO (App. B) | None | 0.5 mg/m3 -(App. B) |
None | 2 mg/m3 | None |
SO2 (App. B) | 1.0 µg/m3 (App. B) |
5 µg/m3 | None | 25 µg/m3 | 30 µg/m3 |
PM10 (App. B) | 1.0 µg/m3 | 5 µg/m3 | None | None | None |
NO2 (App. B) | 1.0 µg/m3 | None | None | None | None |
3. Emission Offsets for Major Stationary Sources in Nonattainment Areas.
a. Applicability.
(1) A new stationary source or a proposed major modification of an existing stationary source in a nonattainment area;
(2) Emissions of air pollutants that are in nonattainment status within the nonattainment area; and
(3) Fugitive emissions generated by point sources, and fugitive emissions from the facility.
b. Standard. Emissions offsets must be sufficient to ensure that all allowable emissions from major and minor sources of the pollutant in nonattainment is < (App. B) the total actual emissions from all sources prior to the NSR application.
c. Requirements for Offsetting Emissions.
1) Allowable emission increases must be offset by actual emission reductions.
2) Proposed new emissions for the source or emission unit(s) providing the emissions offsets must be less than the current level for the source.
3) No emission reduction offset can be credited when the emissions from the source providing the offset exceed allowable emissions rates.
4) Emission reductions imposed by local, state, or federal rules, permits, or orders shall not be used.
5) Emission reductions must provide a net air quality benefit.
(a) For a marginal O3 nonattainment area the VOC or NOx emissions are reduced ≥9% for the nonattainment area.
(b) The determination for other nonattainment areas shall be made using 40 CFR Part 51, Appendix S.
6) Offsets must be federally enforceable.
7) A new or modified source requiring offsets shall not start operations before the emission reductions are achieved.
4. Equipment, Supplier, or Manufacturer Specification.
(4.02 D) Nothing in this regulation shall be construed to
interpreted as authorizing the Board authority to require the use
of emission control apparatus or other equipment, machinery or
devices of any particular type from any particular supplier or
produced by any particular manufacturer. BACT, RACT, or LAER
technology available from any manufacturer may be prescribed for
installation and operation.
5. Absence of Rule or Order. (4.02 D) The absence of any
ordinance, resolution, rule or regulation or the failure to issue
an order pursuant to this section shall not relieve a person from
his or her the obligation to comply with applicable emission
control requirements or with any other provision of the law.
6. Appeals. Appeals of a NSR decision must follow the requirements of section 2.05 (pg. 2-xx).
H. ADDITIONAL REQUIREMENTS FOR THE APPROVAL OF STATIONARY SOURCE NSR APPLICATIONS.
1. PSD Permitting. If the source is determined to be subject to PSD (App. B) permitting, the NSR approval shall be delayed until ecology or EFSEC (App. B) can issue a PSD permit.
2. Content of the Approval. An evaluation of the operational feasibility and economic viability of the proposed emission control devices.
3. Conditions. Review. (4.02 (D)(1)) Every order of
approval of a NSR issued pursuant to this section shall must be
reviewed prior to issuance by a licensed professional engineer in
the employ of the authority or the Washington State Department of
ecology.
4. Expiration of An Approval of a NSR. An approved NSR shall expire for the following reasons:
a. Construction is not begun within 12 months after the receipt of the approval of the NSR;
b. Construction is discontinued for 12 months or more; or
c. Construction is not completed within six months following the approved completion date.
5. Extension of An Approval of a NSR.
a. The source must apply for an extension at least 30 days prior to the expiration date.
b. The approval of an expired NSR is invalid, and the source must submit a new NSR application.
6. Notice of Completion. Notice of Violation. (4.02 F)
The owner or applicant shall must notify the Board or Control
Officer APCO in writing of the completion of construction,
installation or establishment and the date upon which operation
will commence within 30 days after the start of operations for
the process and control apparatus on the NSR application.
7. Final Inspection. (4.02 F) Within thirty (30) days of
receipt of notice of completion, the Board or Control Officer
APCO may, inspect the construction, installation, or
establishment the work approved by the NSR, and the Board or
Control Officer may issue a Notice of Violation, NOV (App. B) if
he finds that the construction, installation, or establishment
the work is not in accordance with the plans, specifications or
other information submitted to approved by the authority.
I. ADDITIONAL REQUIREMENTS FOR THE APPROVAL OF TEMPORARY SOURCE NSR APPLICATIONS.
1. Limited Operation Time. The permission to operate shall
must be for a limited period of time (one year or less).
2. Conditions of Operation. and The authority may set
specific conditions for operation during said period which shall
include a requirement to comply with all applicable emission
standards.
3. Action on Application. Within 30 days of receipt by the authority of a complete application, the authority must issue a final decision on the application.
J. CHANGE OF CONDITIONS. The owner or operator of any source may request a change in a NSR approval order, and the authority may approve the request when:
1. Conditions for Approval.
a. The change of conditions will not cause the source to exceed an emissions standard;
b. No ambient air quality or PSD (App. B) increment will be exceeded by the change;
c. The change will not adversely affect the authority in determining compliance with an emission standard; and
d. The order approving the change shall continue to require BACT as defined at the time of the original approval except where FCAA (App. B) requires LAER.
2. Public Involvement. Shall follow the requirements of section 2.04 (pg. 2-xx).
3. Format for the Request. Unless approved by the authority, the request shall follow the requirements of subsections 4.02D, 4.02E, and/or 4.02F (pg. 4-xx).
K. FEES. Assessment. (4.02 I) Any person submitting a
Notice of Construction pursuant to the terms of this Regulation
shall be assessed a fee by the Authority in accordance with the
fee schedule in Article XIII, Section 13.02 of this regulation.
See current fee schedule.
4.03 NEW SOURCE REVIEW FOR TOXIC AIR POLLUTANTS. Reserved for later use.
4.04 AIR OPERATING PERMITS (AOP). (Chap. 173-401 WAC)
A. PURPOSE. (6.01) The Yakima County Clean Air Authority
shall administer an air operating permit program upon approval of
its delegation request, pursuant to Chapter 173-401 WAC. Under
this program any air contaminant source subject to Chapter
173-401-300 WAC shall be required to have an air operating
permit. (WAC 173-401-100) To reference the appropriate WAC
citations and to define any additional requirements or changes to
implement a local AOP (App. B) program in accordance with chap.
173-401 WAC.
B. APPLICABILITY. As defined in WAC 173-401-300.
C. REQUIREMENTS. When multiple federal, state, or local laws or regulations contain requirements for an AOP source, all laws and regulations apply.
D. DEFINITIONS. As defined in WAC 173-401-200. When a term is not defined in WAC 173-401-200 see app. A for the definition.
E. PERMIT APPLICATIONS. As defined in chap. 173-401 WAC, Part V.
F. PERMIT CONTENT. As defined in chap. 173-401 WAC, Part VI; and
1. Emissions Standards. As required in sections 3.01 (pg. 3-xx) and 3.02 (pg. 3-xx) and app. D (pg. D-1).
2. Monitoring, Recordkeeping, and Reporting. As required in section 3.11 (pg. 3-xx).
3. Terms and Conditions. As required in applicable local rules and this regulation.
4. Operation and Maintenance. As required in subsection 3.00E (pg. 3-xx).
5. Outdoor and Agricultural Burning. As required in section 3.03 (pg. 3-xx).
6. Compliance and Enforcement. As required in subsection 1.07A, article 5 (pg. 5-1), and section 2.05 (pg. 2-xx).
7. Appeals. As required in section 2.05 (pg. 2-xx).
8. Orders. Any relevant order issued by the authority, ecology, or EPA.
G. PERMIT ISSUANCE, RENEWAL, REOPENINGS, AND REVISIONS. As defined in chap. 173-401 WAC, Part VII.
H. GENERAL PERMITS. As defined in chap. 173-401 WAC, Part VIII.
I. PUBLIC INVOLVEMENT. As defined in chap. 173-401 WAC, Part IX and section 2.04 (pg. 2-xx) of this regulation.
J. FEES. (6.02) Pursuant to RCW 70.94.161(14), the Authority
shall allocate its fiscal 1994 air operating permit program
development costs among the sources under its jurisdiction
emitting one hundred tons or more per year of a regulated
pollutant during calendar year 1992 and shall collect interim
fees from these sources. Interim air operating permit fees
collected by the Authority on behalf of the Department of Ecology
shall be remitted to the Department by March 1, 1994.
Pursuant to RCW 70.94, (Bill 1089), the Authority shall determine, assess, and collect annual fees sufficient to cover the Authority's direct and indirect costs of implementing its air operating permit program.
Upon receiving delegation authority, air operating permit fees collected by the Authority on behalf of the Department of Ecology shall be collected from each source in two equal payments and shall be remitted to the Department by March 1 and June 30, respectively, of each year. All air operating permit fees collected by the Authority on its own behalf shall be deposited into an air operating permit account dedicated exclusively to the support of its Air Operating Permit Program. The payment schedule for all air operating permit fees collected by the Authority on its own behalf shall be four equal payments with each payment due at the beginning of the respective fiscal quarter. The fiscal year for the Authority begins July First.
All air operating permit fees collected by the Authority on behalf of itself shall be calculated according to Article XIII, Section 13.05 of this regulation.
1. As defined by chap. 173-401 WAC, Part X; and
2. Section 2.02 (pg. 2-xx) and current fee schedule.
4.05 VOLUNTARY LIMITS ON EMISSIONS. (New Section) (WAC 173-400-091)
A. PURPOSE. To establish a rule for any source who desires to voluntarily limit the potential to emit prescribed pollutants.
B. APPLICABILITY. Any source which volunteers to reduce the potential to emit to levels established by a regulatory order.
1. Synthetic Minor (SM) Status. This is available as an alternative to an AOP (App. B) if the source limits the potential to emit below the following levels:
a. 100 TPY (App. B) of criteria pollutants (App. A) from all point sources at the facility; or
b. 10 TPY of one HAP (App. A) listed in app. L from all point and/or fugitive sources; or
c. 25 TPY of two or more HAPs from all point and/or fugitive sources.
2. All Other Sources. The source does not reduce the potential to emit below the levels in subsection 4.05B1 (pg. 4-xx).
C. CONDITIONS OF THE REGULATORY ORDER.
1. Limits the potential to emit any air pollutant to below voluntary and agreed levels.
2. The new limit for the potential to emit shall be < the annual emissions in subsection 4.05B1 or any standard under WCAA (App. B), FCAA (App. B), or the SIP (App. B).
3. Shall require sufficient monitoring, record keeping, and reporting as defined in section 3.11 (pg. 3-xx) to assure continuous compliance with applicable requirements, including emissions limitations set by a regulatory order (App. A).
4. Shall be federally enforceable.
5. Shall require a revision or revocation of the order for any proposed deviation.
D. ADMINISTRATIVE PROCEDURES.
1. Public participation in the permitting is defined in section 2.04 (pg. 2-xx).
2. The conditions of the order or decision to grant or deny SM status may be appealed as defined in section 2.05 (pg. 2-xx).
E. FEES. See current fee schedule.
4.06 EMISSION REDUCTION CREDITS AND BANKING. Reserved for later use.
4.07 ADMINISTRATIVE PERMITS. (New Section)
A. PURPOSE. To control emissions from sources, groups of sources, or activities which are not subjected to some other form of control.
B. APPLICABILITY. Any lawful activity or source subject to WCAA (App. B) within the jurisdiction of the authority. This section does not apply to any source or activity subject to any of the following actions required in other sections:
1. Orders of approval;
2. Individual permits; or
3. General rule permits.
C. DURATION.
1. The permit expires one year after issuance; or
2. When the board adopts a rule or issues an order to replace the permit.
D. REQUIREMENTS.
1. The permit requirements shall be as effective in controlling emissions as any other similar permit issued by the authority.
2. The APCO may use any lawful permit condition to control a source or activity permitted by this section.
3. Failure to comply with the requirements of this section voids the permit.
E. AMENDMENT OF THE PERMIT. If additional requirements are needed to prevent air pollution and/or protect property, health, safety, and comfort of persons from the effects of the permitted activity; the authority shall amend the permit. When an amendment is made, the authority must notify the responsible person of the limitations, and any requirement imposed will become a condition of the permit.
F. FEES. As set by the current fee schedule.
ARTICLE 5 - COMPLIANCE AND ENFORCEMENT
5.00 GENERAL INFORMATION. (New Section)
A. PURPOSE. To establish the general compliance and enforcement procedures.
B. APPLICABILITY. Applies to all sources regulated by the authority or any violation of this regulation, any applicable law, or any permit, order or condition of approval issued by the authority.
C. INVESTIGATION. The authority will conduct investigations for the purpose of determining compliance with this regulation, any of the laws or regulations enforced by the authority, any permit issued by the authority, any order issued by the authority, or any condition of approval issued by the authority.
D. WRITTEN NOTICES.
1. The authority will serve a written notice to any person that has caused or allowed an alleged violation of this regulation, any applicable law, or any permit, order or condition of approval issued by the authority.
2. See subsection 3.01C3a3) (pg. 3-xx) for a NOV (App. B) for agricultural odors.
5.01 ADDITIONAL OR ALTERNATIVE ENFORCEMENT ACTIONS
A. PURPOSE. To describe other provisions to use with or in addition to civil or criminal penalties to avoid a violation or gain compliance.
B. APPLICABILITY. This section applies to any person found to be in violation of this regulation, any applicable law, or any permit, order or condition of approval issued by the authority. This section also applies to any situation where an imminent health threat exists.
C. CORRECTIVE ACTION ORDER. The authority may issue a corrective action order that describes the actions necessary to correct or avoid a violation. The order may be included as part of a written notice or issued as a separate document.
D. PROHIBITORY ORDER. The authority may issue a prohibitory order for the purpose of protecting human health or safety. The order will prohibit specific actions from being taken at a specific location.
E. INJUNCTIVE RELIEF. SECTION 8.04 - RESTRAINING ORDER - INJUNCTIONS. Notwithstanding the existence or use of any other
remedy, whenever any person has engaged in, or is about to engage
in, any acts or practices which constitute or will constitute a
violation of any provision of theseis regulations or order issued
thereunder, the Board, APCO (App. B) after providing notice to
such person and an opportunity to comply, may petition the
superior court of the county wherein the violation is alleged to
be occurring or to have occurred for a restraining order, or a
temporary or permanent injunction or other appropriate order.
F. ASSURANCE OF DISCONTINUANCE. SECTION 8.03 - ASSURANCE OF
DISCONTINUANCE. As an additional means of enforcing these
regulations, the APCO Board may accept an assurance of
discontinuance of any act or practice deemed in violation of this
regulation., from any person engaging in, or who has engaged in,
such act or practice. Any such The assurance must shall specify
a time limit during which such the discontinuance is to be
accomplished. Failure to perform the terms of any such assurance
shall constitute prima facie proof of a violation of these
regulation, or order issued pursuant hereto, which make the
alleged act or practice unlawful for the purpose of securing any
injunction or other relief from the Superior Court as provided in
RCW 70.94.425.
5.02 PENALTY FOR VIOLATION PENALTIES (8.01)
A. PURPOSE. To describe the provisions for assessing penalties for violations.
B. APPLICABILITY. This section applies to any person found to be in violation of this regulation, any applicable law, or any permit, order or condition of approval issued by the authority.
C. CRIMINAL PENALTIES. Shall be imposed in accordance to chap. 70.94 RCW.
1. (8.01A) Any person who knowingly violates any of the
provisions of these regulations or any ordinance, resolution,
statute or regulation in force pursuant thereto shall be guilty
of a crime and upon conviction thereof shall be punished by a
fine of not more than Ten Thousand Dollars ($10,000) or by
imprisonment in the county jail for not more than one (1) year,
or both.
2. (8.01B) Any person who negligently releases into the ambient air any substance listed by the Department of Ecology or as a hazardous air pollutant other than in compliance with the terms of an applicable permit or emission limit, and who at the time negligently places another person in imminent danger of death or substantial bodily harm shall be guilty of a crime and shall, upon conviction, be punished by a fine of not more than Ten Thousand Dollars ($10,000) or by imprisonment for not more than one (1) year, or both.
3. (8.01C) Any person who knowingly releases into the ambient air any substance listed by the Department of ecology as a hazardous air pollutant, other than in compliance with the terms of an applicable permit or emission limit, and who knows at the time that he or she thereby places another person in imminent danger of death or substantial bodily harm shall be guilty of a crime and shall, upon conviction, be punished by a fine of not more than Fifty Thousand Dollars ($50,000) or by imprisonment for not more than five (5) years, or both.
4. (8.01D) Any person who knowingly fails to disclose a potential conflict of interest under RCW 70.94.100 shall be guilty of a gross misdemeanor and upon conviction thereof shall be punished by a fine of not more than Five Thousand Dollars ($5,000).
D. CIVIL PENALTIES. SECTION 8.02 - ADDITIONAL OR ALTERNATIVE
PENALTIES
1. General Civil Penalty. (8.02A) In addition to or as an
alternate to any other penalty provided by law, any person who
violates the provisions of chap. 70.94 RCW, chap.ter 70.120 RCW,
or any other of the rules or and regulations, the Yakima County
Clean Air authority may enforce under the RCW (App. B) a civil
penalty in an amount not to exceed Ten Thousand Dollars ($12,000)
per day for each violation. Each such violation shall be a
separate and distinct event, and, in the case of a continuing
violation, each days continuance day shall be a separate and
distinct violation.
2. Penalty for Failure to Comply with an Order. Any person
who fails to take action as specified by an order issued under
this Chapter article shall be liable for a civil penalty of not
more than Ten Thousand Dollars ($12,000) per day for each day of
continued noncompliance.
E. INTEREST ON PENALTIES. (8.02B) Penalties incurred but not
paid shall accrue interest beginning on the ninety-first (91st)
day following the date that the penalty becomes due and payable
at the highest rate allowed by RCW 19.52.020 on the date that the
penalty becomes due and payable. If violations or penalties are
appealed interest shall not begin to accrue until the
thirty-first (31st) day following the final resolution of the
appeal.
F. AIDING OR ABETTING. (8.02C) Each act of commission or
omission which procures, aids or abets the a violation described
herein shall be considered a separate violation under the
provisions of this section and subject to the same penalty. The
penalties provided in this section shall be imposed pursuant to
RCW 43.12(B).300.
G. UNDER-REPORTING. (8.02D) In addition to the other penalties
provided above, any person knowingly under-reporting emissions or
other information used to set fees or persons required to pay
emissions or permit fees who are more than ninety (90) days late
with such payments may be subject to a penalty equal to three (3)
times the amount of the original fee owed.
H. DISBURSEMENT. (8.02E) All penalties recovered under this section by the authority shall be paid into the treasury of the authority and rendered into its funds.
F. In addition to the other provisions of this Section, a
specific Civil Penalty may be imposed in violation of other
Sections of this Regulation in accordance to the following
schedule: (see page 8-3)
I. WITHHOLDING GRANTS. (8.02G) Public or private entities that
are recipients or potential recipients of department grants from
the authority, whether for air quality related activities or not,
may have such the grants rescinded or withheld by the department
authority for failure to comply with provisions of this chapter
regulation.
J. PENALTY DETERMINATION. Civil Penalty Schedule. (8.02)
All Outdoor Burning |
||||
All Outdoor Burning within the Jurisdiction of the YCCAA, Local Cities, Towns, Fire Protection Districts and Conservation Districts |
Warning to $25 |
$25 to $50 |
$50 to $100 |
Up to $10,000 |
Issued by YCCAA for All Other Outdoor Burning |
$25 to $500 |
Up to $1,000 |
Up to $2,000 |
Up to $10,000 |
Outdoor Burning |
$25 to $500 |
Up to $1,000 |
Up to $2,000 |
Up to $10,000 |
Permissible Emissions |
Warning to $25 |
$25 to $50 |
$50 to $100 |
|
Combustion and Incineration Sources |
$50 to $500 |
Up to $1,000 |
Up to $2,000 |
Up to $10,000 |
for Certain Source Categories |
Warning to $25 |
$25 to $50 |
$50 to $100 |
|
Warning to $25 |
$25 to $50 |
$50 to $100 |
1. Evaluation Criteria. The following criteria shall be
used to evaluate a violation prior to assessing a penalty:
a. Gravity of the violation;
b. Economic benefit gained by the violator;
c. Authority expenses for investigating, notifying, and processing the documents for the violation; and
d. When requested, the costs incurred by a fire department (App. A) to respond or suppress an illegal outdoor or agricultural fire.
2. Documentation. The APCO shall prepare and the board approve a policy and worksheets to implement the penalty determinations.
Definitions of Words and Phrases
This appendix contains a list of definitions for words and phrases used in more than one section of the regulation. Defined words or phrases are identified with "(App. A)" in the text. The source of the definition is identified in italics.
Actual Emissions (WAC 173-400-030(1)) - The actual rate of
emissions of a pollutant from an emissions unit, as determined in
accordance with (a) through (c) of this subsection by:
1. In general, actual emissions as of a particular date
shall equal the average rate, in tons per year TPY (App. B), at
which the emissions unit actually emitted the pollutant during a
two-year period which precedes the particular date and which is
representative of normal source operation. Ecology or an the
authority shall allow the use of a different time period upon a
determination that it is more representative of normal source
operation. Actual emissions shall be calculated using the
emissions unit's actual operating hours, production rates, and
types of materials processed, stored, or combusted during the
selected time period.
2. Ecology or an the authority may presume that
source-specific allowable emissions for the unit are equivalent
to the actual emissions of the emissions unit.
3. For any emissions unit which has not begun normal operations on the particular date, actual emissions shall equal the potential to emit of the emissions unit on that date.
Adequate Source of Heat (WAC 173-433-030(1)) - The ability
to maintain 70 degrees °Fahrenheit (App. B) at a point three (3)
feet above the floor in all normally inhabited areas of the
dwelling.
Adverse Impact on Visibility (WAC 173-400-030(2)) -Visibility impairment which interferes with the management, protection, preservation, or enjoyment of the visitor's visual experience of the Federal Class I area. This determination must be made on a case by case basis taking into account the geographic extent, intensity, duration, frequency, and time of visibility impairment, and how these factors correlate with (a) times of visitor use of the Federal Class I area, and (b) the frequency and timing of natural conditions that reduce visibility. This term does not include effects on integral vistas. These areas are listed in the definition for Class I Areas.
Agricultural Activity (RCW 70.94.640 (5)(a)) - The growing, raising, or production of horticultural or viticultural crops, berries, poultry, livestock, grain, mint, hay, and dairy products. This definition applies only to subsection 3.01C3.
Agricultural Burning (WAC 173-430-030(1)) - The burning of vegetative debris from an agricultural operation necessary for disease or pest control, necessary for crop propagation and/or crop rotation, or where identified as a best management practice by the agricultural burning practices and research task force established in RCW 70.94.650 or other authoritative source on agricultural practices.
Agricultural Land (RCW 70.94.640 (5)(c)) - At least five acres of land devoted primarily to the commercial production of livestock or agricultural commodities. This definition applies only to subsection 3.01C3.
Agricultural Operation - The growing of crops, the raising
of fowl, animals or bees as a gainful occupation. (WAC 173-430-030(2)) - A farmer who can substantiate that the
operation is commercial agriculture by showing the most recent
year's IRS (App. B) schedule F form or proof that the land is
designated in a classification for agricultural use. It also
includes burning conducted by irrigation district or drainage
district personnel as part of water system management.
Ag Task Force (WAC 173-430-030(3)) - The state agricultural burning practices and research task force.
Air Contaminant (WAC 173-400-030(3)) - Dust, fumes, mist, smoke, other particulate matter, vapor, gas, odorous substance, or any combination thereof. "Air pollutant" means the same as "air contaminant".
Air Pollution (WAC 173-400-030(4)) - The presence in the outdoor atmosphere of one or more contaminants in sufficient quantities and of such characteristics and duration as is, or is likely to be, injurious to human health, plant or animal life, or property, or which unreasonably interferes with enjoyment of life and property. For the purpose of this regulation, air pollution shall not include air contaminants emitted in compliance with Chapter 17.21 RCW (App. B), the WA Pesticide Application Act, which regulates the application and control of various pesticides.
Air Pollution Episode - A period of impaired air quality as
determined by the Director of the Yakima County Clean Air
authority, or the Washington State Department of ecology. A
period when a forecast, alert, warning, or emergency air
pollution stage is declared, as stated in chap. 173-435 WAC.
Allowable Emissions (WAC 173-400-030(5)) - The emission rate of a stationary source calculated using the maximum rated capacity of the stationary source (unless the stationary source is subject to federally enforceable limits which restrict the operating rate, or hours of operation, or both) and the most stringent of the following:
1. The applicable standards as set forth in 40 CFR Part 60 or 61 (App. B);
2. Any applicable state implementation plan SIP (App. B)
emissions limitation including those with a future compliance
date; or
3. The emissions rate specified as a federally enforceable permit condition, including those with a future compliance date.
Ambient Air (WAC 173-400-030(6)) - The surrounding outside air.
Ambient Air Quality Standard (WAC 173-400-030(7)) - An established concentration, exposure time, and frequency of occurrence of air contaminant(s) in the ambient air which shall not be exceeded.
Authority - The Yakima Regional Clean Air Authority.
Best Available Control Technology (BACT) (WAC 173-400-030(10)) - The term as defined in WAC 173-400. An
emission limitation based on the maximum degree of reduction for
each air pollutant subject to regulation under chap.ter 70.94 RCW
(App. B) emitted from or which results from any new or modified
stationary source, which the permitting authority, on a
case-by-case basis, taking into account energy, environmental,
and economic impacts and other costs, determines is achievable
for such source or modification through application of production
processes and available methods, systems, and techniques,
including fuel cleaning, clean fuels, or treatment or innovative
fuel combustion techniques for the control of each such
pollutant. In no event shall application of the BACT (App. B)
result in emissions of any pollutants which will exceed the
emissions allowed by any applicable standard under 40 CFR Part 60
and Part 61 (App. B), as they exist on March 1, 1996, or their
later enactments as adopted by reference by the ecology.
Emissions from any source utilizing clean fuels, or any other
means, to comply with this definition shall not be allowed to
increase above levels that would have been required under the
definition of BACT in FCAA (App. B) as it existed prior to
enactment of the FCAA Amendments of 1990.
Best Management Practice (BMP) (WAC 173-430-030(4)) - The criteria established by the state ag task force.
Board - The Board of Directors of the Yakima Regional Clean Air Authority
Bubble (WAC 173-400-030(12)) - A set of emission limits which allows an increase in emissions form a given emission(s) unit(s) in exchange for a decrease in emissions from another emissions unit(s) pursuant to RCW 70.94.155 and WAC 173-400-120.
Burn Bans - Periods when ecology or the authority determine air contaminant levels are approaching or have reached a level which is harmful to public health or safety. Outdoor burning, agricultural burning, and burning with wood or coal heaters are severely curtailed during these periods.
Ceremonial Fires - Fires necessary for Native American ceremonies (i.e. conducted by and for Native Americans) if part of a religious ritual.
Class I Area (WAC 173-400-030(14)) - Any area designated under §§ 162 or 164 of FCAA (App. B) as a class I area. The following areas are the class I areas in Washington state;
1. Alpine Lakes Wilderness Area;
2. Glacier Peak Wilderness Area;
3. Goat Rock Wilderness Area;
4. Mount Adams Wilderness Area;
5. Mount Rainier National Park;
6. North Cascades National Park;
7. Olympic National Park;
8. Pasayten Wilderness Area; and
9. Spokane Indian Reservation.
Combustible Refuse - Any burnable waste material containing
carbon in a free or combined state other than liquid or gasses.
Combustion and Incineration Sources (WAC 173-400-030(15))
-Units using combustion for waste disposal, steam production,
chemical recovery or other process requirements; but excludes
open outdoor burning.
Commenced Construction (WAC 173-400-030(16)) - The owner or operator has all the necessary preconstruction approvals or permits and either has:
1. Begun, or caused to begin, a continuous program of actual on-site construction of the source, to be completed within a reasonable time; or
2. Entered into binding agreements or contractual obligations, which cannot be canceled or modified without substantial loss to the owner or operator, to undertake a program of actual construction of the source to be completed within a reasonable time.
Concealment (WAC 173-400-030(17)) - Any action taken to reduce the observed or measured concentrations of a pollutant in a gaseous effluent while, in fact, not reducing the total amount of pollutant discharged.
Construction/Demolition Debris - All material resulting from the construction, renovation, or demolition of buildings, roads, and other man-made structures.
Control Apparatus - Any device which prevents or controls the emission of any air contaminant.
Control Officer - The Air Pollution Control Officer of the
Yakima Regional Clean Air Authority, or his duly authorized
agents.
Corrective Action Order - An order issued by the authority for the purpose of causing a person to be in compliance with cited authority, state, or federal laws and regulations. The order will specify actions to be taken within a specific time.
Criteria Pollutant (WAC 173-420-040) - Air pollutants for which a NAAQS (App. B) has been promulgated under FCAA (App. B) (40 CFR Part 50) and their precursors.
Daylight Hours - 30 minutes before and 30 minutes after the published sunrise and sunset times in a newspaper of general circulation in the area.
De Minimis - The minimum threshold levels that exempts sources or source categories from complying with specific requirements.
DEQ Phase 2 Woodstove (WAC 173-433-150 (1)(c)) - A woodstove meeting the "Oregon Department of Environmental Quality Phase 2" emissions standards contained in Subsections (2) and (3) of Section 340-21-115, and certified in accordance with "Oregon Administrative Rules, Chapter 340, Division 21 - Woodstove Certification" dated November 1984.
Director - Executive Director and Control Officer.
Eight Hours (WAC 173-435-020(5)) - Any consecutive eight hours starting at any clock hour.
Emission (WAC 173-400-030(21)) - A release of air contaminants into the ambient air.
Emission Reduction Credit (ERC) (WAC 173-400-030(22)) - A
credit granted pursuant to under WAC 173-400-131. This is a
voluntary reduction in emissions.
Emission Standards - A limitation on the release of a
contaminant or multiple contaminants into the ambient air. (WAC 173-400-030(23)) A requirement established under FCAA (App. B) or
WCAA (App. B) which limits the quantity, rate, or concentration
of emissions of air contaminants on a continuous basis, including
any requirement relating to the operation or maintenance of a
source to assure continuous emission reduction and any design,
equipment work practice, or operational standard promulgated
under FCAA or WCAA.
Emissions Unit (WAC 173-400-030(24)) - Any part of a
stationary source or source which emits or would have the
potential to emit any pollutant subject to regulation under the
FCAA (App. B), chap.ter 70.94 or 70.98 RCW (App. B).
EPA Certified Woodstove (WAC 173-433-030(2)) - A woodstove that meets the emission performance standards when tested by an accredited independent laboratory and labeled according to procedures specified by the EPA (App. B) under 40 CFR Part 60, Subpart AAA (App. B) - Standards of Performance for Residential Wood Heaters as amended through July 1, 1990.
EPA Exempted Device - A device that is not required to be tested under 40 CFR Part 60, Subpart AAA.
Equipment - Any stationary or portable device or any part thereof capable of causing the emission of any air contaminant into the ambient air.
Excess Emissions (WAC 173-400-030(25)) - Emissions of an air pollutant in excess of any applicable emissions standard.
Farmer (WAC 173-430-030(7)) - Any person engaged in the business of growing or producing for sale upon their own lands, or upon the land in which they have a present right of possession, any agricultural product. Farmer does not mean persons using such products as ingredients in a manufacturing process, or persons growing or producing such products primarily for their own consumption.
Federal Land Manager (WAC 173-400-030(29)) - With respect to
any lands in the United States, the Secretary of the department
with authority over such lands.
Fire Department - Fire control agency such as city fire
departments, local fire districts or the Washington State
Department of Natural Resources DNR (App. B).
Fire Fighting Training Fires - Fires for the instruction in methods of fire fighting, including but not limited to training to fight structural fires, aircraft crash rescue fires, and forest fires.
Fireplace (RCW 70.94.453(3)) - Any permanently installed masonry fireplace; or any factory-built metal solid fuel burning device designed to be used with an open combustion chamber and without features to control the air to fuel ratio.
Firewood - Bare untreated wood used as fuel in a wood heater, solid fuel burning device, ceremonial fire, or a recreational fire.
First Stage of Impaired Air Quality - Can be declared by the
authority wWhen particulate ten microns PM10 and smaller in
aerodynamic diameter are is at an ambient level of seventy-five
60 micrograms per cubic meter µg/m3 (App. B) of air measured on a
twenty-four 24 hour average, or when carbon monoxide CO (App. B)
is at an ambient level of eight ppm parts of contaminant per
million parts of air by volume measured on an eight-hour average.
Fossil Fuel-fired Steam Generator (WAC 173-400-030(30)) - A device, furnace, or boiler used in the process of burning fossil fuel for the primary purpose of producing steam by heat transfer.
Fugitive Dust (WAC 173-400-030(31)) - A particulate emission made airborne by forces of wind, man's activity, or both. Unpaved roads, construction sites, and tilled land are examples or areas that originate fugitive dust. Fugitive dust is a type of fugitive emission.
Fugitive Emissions (WAC 173-400-030(32)) - Emissions which
do not pass and which could not reasonabley pass through a stack,
chimney, vent, or other functionally equivalent opening.
Furnace (40 CFR 60.531) - A solid fuel burning appliance that is designed to be located outside of ordinary living areas and that warms spaces other than the space where the appliance is located, by the distribution of air heated in the appliance through ducts. The appliance must be tested and listed as a furnace under accepted American or Canadian safety testing codes unless exempted from this provision by the EPA. A manufacturer may request an exemption in writing from the EPA by stating why the testing and listing requirement is not practicable and demonstrating that his appliance is otherwise a furnace.
Garbage - Putrescible animal and vegetable wastes resulting from the handling, preparation, cooking or serving of food.
General Process Unit Source (WAC 173-400-030(33)) - An
emissions unit using a procedure or a combination of procedures
for the purpose of causing a change in material by either
chemical or physical means, excluding combustion.
Good Agricultural Practice (RCW 70.94.640 (5)(b)) - The economically feasible practices which are customary among or appropriate to farms and ranches of a similar nature in the local area. This definition applies only to subsection 3.01C3.
Good Engineering Practice (GEP) (WAC 173-400-030(34)) - A calculated stack height based on the equation specified in WAC 173-400-200 (2)(a)(ii).
Hazardous Air Pollutant - Any air pollutant listed in accordance with section 112(b), FCAA (App. B).
Hearings Board - Hearings Boards as established by RCW 43.21B.
Home Barbecues - A small wood, charcoal, LP (App. B) gas, or natural gas fire for the purpose of cooking.
Hour (WAC 173-435-020(4)) - A 60 minute period, beginning and ending on a clock hour.
Impaired Air Quality - A first or second stage impaired air quality condition declared by ecology or the authority in accordance with WAC 173-433-140.
Incinerator (WAC 173-400-030(35)) - A furnace for the
destruction of waste, or oxidizing a waste to facilitate disposal
used primarily for the thermal destruction of waste.
Land Clearing Burning - Outdoor fires consisting of residue
of a natural character such as trees, stumps, shrubbery of other
natural vegetation arising from land clearing projects and burned
on the lands on which such materials originated. Outdoor burning
of trees, stumps, shrubbery, or other natural vegetation from
land clearing projects (i.e. projects that clear the land surface
so it can be developed, used for a different purpose, or left
unused).
Lowest Achievable Emission Rate (LAER) (WAC 173-400-030(38))
- The term as defined in WAC 173-400. The rate of emissions for
any source which reflects the more stringent of:
1. The most stringent emission limitation which is contained in the SIP (App. B) for a class or category of source, unless the owner or operator of the proposed new or modified source demonstrates that the limitations are not achievable; or
2. The most stringent emission limitation which is achieved in practice by such class or category of source.
In no event may the application of this term permit a proposed new or modified source to emit any pollutant in excess of the amount allowable under applicable new source performance standards.
Major Modification (WAC 173-400-030(40)) - Any physical
change in or change in the method of operation of a major
stationary source that would result in a significant net
emissions increase of any pollutant subject to regulation under
the FCAA (App. B). Any net emissions increase that is considered
significant for volatile organic compounds VOCs (App. B) or
nitrogen oxides NOx (App. B) shall be considered significant for
ozone O3 (App. B). A physical change or change in the method of
operation shall not include:
1. Routine maintenance, repair, and replacement;
2. Use of an alternative fuel or raw material by reason of an order under sections 2 (a) and (b) of the Energy Supply and Environmental Supply Coordination Act of 1974 (or any superseding legislation) or by reason of a natural gas curtailment plan pursuant to the Federal Power Act:
3. Use of an alternative fuel by reason of an order or rule under section 125 of the FCAA, 42 U.S.C. 7425 (App. B);
4. Use of an alternative fuel at a steam generating unit to the extent that the fuel is generated from municipal solid waste;
5. Use of an alternative fuel or raw material by a stationary source which:
a. The stationary source was capable of accommodating before December 21, 1976, unless such change would be prohibited under any federally enforceable permit condition which was established after December 12, 1976; pursuant to 40 CFR 52.21 or under regulations approved pursuant to 40 CFR 51 Subpart I, or 40 CFR 51.166; in a prevention of significant deterioration permit or notice of construction approval; or
b. The stationary source is approved to use under any
federally-enforceable notice of construction NSR (App. B)
approval or a PSD (App. B) permit issued by the environmental
protection agency EPA (App. B) or ecology;
6. An increase in the hours of operation or in the
production rate, unless such change is prohibited under any
federally enforceable permit condition which was established
after December 21, 1976; pursuant to 40 CFR 52.21 or under
regulations approved pursuant to 40 CFR 51 Subpart I, or 40 CFR
51.166; in a prevention of significant deterioration permit or a
notice of construction NSR approval;
7. Any change in ownership at a stationary source.
Major Stationary Source (WAC 173-400-030(41)) -
1. Any stationary source which:
a. Emits or has the potential to emit one hundred tons per
year 100 TPY (App. B) or more of any air contaminant regulated by
the state WCAA (App. B) ofr Federal Clean Air Acts FCAA (App. B);
or
b. Is located in a "marginal" or "moderate" ozone O3 (App.
B) nonattainment area and which emits or has the potential to
emit one hundred tons per year 100 TPY (App. B) or more of
volatile organic compounds VOCs (App. B) or oxides of nitrogen
NOx (App. B).
2. Any stationary source (or group of stationary sources) which:
a. Is located in a "serious" carbon monoxide CO (App. B)
nonattainment area where stationary sources contribute
significantly to carbon monoxide CO levels and which emits or has
the potential to emit fifty tons per year 50 TPY (App. B) or more
of carbon monoxide CO; or
b. Is located in a "serious" particulate matter (PM10) (App.
B) nonattainment area and which emits or has the potential to
emit seventy tons per year 70 TPY or more of PM10 emissions.
3. Any physical change that would occur at a stationary
source not qualifying under (a) or (b) parts 1 or 2 of this
subsection definition as a major stationary source, if the change
would constitute a major stationary source by itself;
4. A major stationary source that is major for VOCs or NOx
shall be considered major for ozone O3 (App. B);
5. The fugitive emissions of a stationary source shall not
be included in determining whether it is a major stationary
source, unless the stationary source belongs to one of the
following categories of stationary sources or the source is a
major stationary source due to (b) part 2 of this subsection
definition;
a. Coal cleaning plants (with thermal dryers);
b. Kraft pulp mills;
c. Portland cements plants;
d. Primary zinc smelters;
e. Iron and steel mills;
f. Primary aluminum ore reduction plants;
g. Primary copper smelters;
h. Municipal incinerators capable of charging more than two
hundred fifty 250 tons of refuse per day;
i. Hydrofluoric, sulfuric, or nitric acid plants;
j. Petroleum refineries;
k. Lime plants;
l. Phosphate rock processing plants;
m. Coke oven batteries;
n. Sulfur recovery plants;
o. Carbon black plants (furnace process);
p. Primary lead smelters;
q. Fuel conversion plants;
r. Sintering plants;
s. Secondary metal production plants;
t. Chemical process plants;
u. Fossil-fuel boilers (or combination thereof) totaling
more than two hundred fifty million 250,000,000 British thermal
units BTUs (App. B) per hour heat input;
v. Petroleum storage and transfer units with a total storage
capacity exceeding three hundred thousand 300,000 barrels;
w. Taconite ore processing plants;
x. Glass fiber processing plants;
y. Charcoal production plants;
z. Fossil fuel-fired steam electric plants of more than two
hundred fifty million 250,000,000 British thermal units BTUs per
hour heat input; and
aa. Any other stationary source category which, as of August
7, 1970, was being regulated under sections 111 or 112 of the
Federal Clean Air Act FCAA (App. B).
6. For purposes of determining whether a stationary source
is a major stationary source, the term "building, structure,
facility, or installation" means all the pollutant-emitting
activities which belong to the same industrial grouping, are
located on one or more contiguous or adjacent properties, and are
under the control of the same person (or persons under common
control). Pollutant-emitting activities shall be considered as
part of the same industrial grouping if they belong to the same
major group (i.e., which have the same two digit code) as
described in the Standard Industrial Classification Manual, 1972,
as amended by the 1977 Supplement North American Industry
Classification System (NAICS) as amended.
7. This definition does not apply to section 4.04.
Materials Handling (WAC 173-400-030(43)) - The handling, transporting, loading, unloading, storage, and transfer of materials with no significant chemical or physical alteration.
Maximum Available Control Technology (MACT) - A standard developed for the control of hazardous air pollutant emissions from specific source categories regulated under 40 CFR Part 63. The full definitions for MACT for existing sources, MACT for new sources, and MACT floor are in 40 CFR 63.51.
Minor Source - Any stationary source which is not a major stationary source (App. A).
Modification (WAC 173-400-030(44)) - Any physical change in
or change in the method of operation of a stationary source that
increases the amount of any air contaminant emitted by such the
source or that results in the emission of any air contaminant not
previously emitted. The term modification shall be construed
consistent with the definition of modification in section 7411,
Title 42, United State Code USC (App. B) and with rules
implementing that section.
Multiple Chamber Incinerator - Any incinerator consisting of
three or more refractory-lined combustion chambers in series,
physically separated by refractory walls, interconnected by gas
passage ports or ducts and employing adequate design parameters
necessary for maximum combustion of the material to be burned.
National Emission Standards for Hazardous Air Pollutants (NESHAPS) (WAC 173-400-030(45)) - The federal regulations set forth in 40 CFR Part 61 and 63 (App. B).
Natural Vegetation - Unprocessed plant material from herbs, shrubbery, and trees, including grass, weeds, leaves, clippings, prunings, brush, branches, roots, stumps, and trunk wood.
Net Emissions Increase (WAC 173-400-030(47))
1. The amount by which the sum of the following exceeds zero:
a. Any increase in actual emissions from a particular change or change in method of operation at a source; and
b. any other increases and decreases in actual emissions at the source that are contemporaneous with the particular change and are otherwise creditable.
2. An increase or decrease in actual emissions is
contemporaneous with the increase from the particular change only
if it occurs between the date ten five years before construction
on the particular change commences and the date that the increase
from the particular change occurs.
3. An increase or decrease in actual emissions is creditable only if:
a. It occurred no more than one year prior to the date of
sSubmittal of a complete notice of construction application for
the particular change, or it has been documented by an emission
reduction credit, in which case the credit shall expire ten five
years after the date of original issue of the ERC (App. B). Any
emissions increases occurring between the date of issuance of the
ERC and the date when a particular change becomes operational
shall be counted against the ERC.
b. Ecology or the authority has not relied on it in issuing
any permit or order of approval for the source under regulations
approved pursuant to under 40 CFR 51 Subpart I or the EPA (App.
B) or ecology has not relied on it in issuing a PSD (App. B)
permit pursuant to 40 CFR 52.21, which order or permit is in
effect when the increase in actual emissions from the particular
change occurs.
4. An increase in actual emissions is creditable only to the extent that the new level of actual emissions exceeds the old level.
5. A decrease in actual emissions is creditable only to the extent that:
a. The old level of actual emissions or the old level of allowable emissions, whichever is lower, exceeds the new level of actual emissions;
b. It is federally enforceable at and after the time that actual construction on the particular change begins;
c. It has approximately the same qualitative significance for public health and welfare as that attributed to the increase from the particular change; and
d. Ecology or the authority has not relied on it in issuing
any permit or order of approval under regulations approved
pursuant under 40 CFR 51 Subpart I (App. B), the EPA (App. B) or
ecology has not relied on it in issuing a PSD (App. B) permit
pursuant to 40 CFR 52.21, or ecology or the authority has not
relied on it in demonstrating attainment or reasonable further
progress.
6. An increase that results from a physical change at a
source occurs when the emission unit on which construction
occurred becomes operational and begins to emit a particular
pollutant. Any replacement unit that requires shakedown becomes
operational only after a reasonable shakedown period, not to
exceed one hundred eighty 180 days.
New Source (WAC 173-400-030(48))
1. The construction or modification of a stationary source
that increases the amount of any air contaminant emitted by such
a source or that results in the emission of any air contaminant
not previously emitted, and;
2. Any other project that constitutes a new source under the
Federal Clean Air Act FCAA (App. B).
New Source Performance Standards (NSPS) (WAC 173-400-030(49)) - The federal regulations set forth in 40 CFR Part 60 (App. B).
New Source Review (NSR) - The process for the review and approval or denial of a new source review application.
New Source Review Application - Has the same meaning as notice of construction application.
New Wood Stove (RCW 70.94.453(4)) - A wood stove or wood heater that is sold at retail, bargained, exchanged, or given away for the first time by the manufacturer, the manufacturer's dealer or agency, or a retailer; and has not been so used to have become what is commonly known as "second hand" within the ordinary meaning of that term.
Nonattainment Area - A clearly delineated geographic area
which has been designated by EPA promulgation as exceeding a
national ambient air quality standard or standards because it
does not meet (or it contributes to ambient air quality in a
nearby area that does not meet) a NAAQS(s) (App. B) for one or
more of the criteria pollutants (App. A), which include CO (App.
B), PM (PM10 and PM2.5) (App. B), SO2 (App. B), NO2 (App. B), Pb
(App. B), and O3 (App. B).
Notice of Construction Application (NOC) (WAC 173-400-030(51)) - A written application to permit construction
of a new source, modification of an existing source or
replacement or substantial alteration of control technology at an
existing stationary source. Replacement or substantial
alteration of control technology does not include routine
maintenance, repair, or parts replacement. This application has
the same meaning as a NSR application.
Nuisance - An emission of smoke or any other air pollutant that unreasonably interferes with the use or enjoyment of the property upon which it is deposited.
Opacity (WAC 173-400-030(52)) - The degree to which an object seen through a plume is obscured, stated as a percentage.
Open Fire - A fire where any material is burned in the open
or in a receptacle other than a furnace, incinerator, or other
equipment connected to a stack or chimney.
Order - An order issued by ecology or the authority under chap. 70.94 RCW (App. B), including, but not limited to RCW 70.94.332, RCW 70.94.152, RCW 70.94.153, and RCW 70.94.141(3), and includes, where used in the generic sense, the terms order, corrective action order, order of approval, and regulatory order.
Order of Approval or Approval Order (WAC 173-400-030(55)) - A regulatory order issued by ecology or the authority to approve
the notice of construction NSR (App. B) application for a
proposed new source or modification, or the a replacement or
substantial alteration of control technology at an existing
stationary source, or to approve alternative methods of ACM (App.
B) removal.
Other Outdoor Burning - Any type of outdoor burning not specified in WAC 173-425-020 including, but not limited to, any outdoor burning necessary to protect public health and safety.
Outdoor Burning (WAC 173-400-030(53)) - The combustion of material of any type in an open fire or in an outdoor container without providing for the control of combustion or the control of emissions from the combustion.
Owner - Includes the person who leases, supervises or
operates the equipment or control apparatus.
Particle - A small discrete mass of solid or liquid matter.
(General size range from submicron to 2000 micron).
Particulate Matter or Particulate (PM) (WAC 173-400-030(56)) - Any airborne finely divided solid or liquid material with an aerodynamic diameter smaller than 100 micrometers.
Particulate Matter Emissions (WAC 173-400-030(57)) - All
finely divided solid or liquid material, other than uncombined
water, emitted to the ambient air as measured by applicable
reference methods, or an equivalent or alternative method
specified in 40 CFR Part 60 (App. B) or by a test method
specified in the Washington state implementation plan SIP (App.
B).
Parts Per Million (ppm) (WAC 173-400-030(58)) - Parts of a contaminant per million parts of gas, by volume, exclusive of water or particulate.
Pellet Stove (WAC 173-433-030(6)) - A pellet stove with an
air-to-fuel ratio equal to or greater than ≥ (App. B) 35.0 when
tested by an accredited laboratory in accordance with methods and
procedures specified by the EPA in 40 CFR Part 60 Appendix A,
Reference Method 28A - Measurement of Air to Fuel Ratio and
Minimum Achievable Burn Rates for Wood-fired Appliances as
amended through July 1, 1990.
Person (WAC 173-400-030(59)) - Any individual, firm, public or private corporation, association, partnership, political subdivision, municipality or governmental agency.
PM2.5 - Ultra finely divided solid or liquid material, including condensible particulate matter, with an aerodynamic diameter less than or equal to a nominal 2.5 micrometers emitted to the ambient air.
PM10 (WAC 173-400-030(60)) - Particulate matter with an aerodynamic diameter less than or equal to a nominal 10 micrometers as measured by a reference method based on 40 CFR Part 50 Appendix J (App. B) and designated in accordance with 40 CFR Part 53 or by an equivalent method designated in accordance with 40 CFR Part 53.
PM10 Emissions (WAC 173-400-030(61)) - Finely divided solid
or liquid material, including condensible particulate matter,
with an aerodynamic diameter less than or equal to a nominal 10
micrometers emitted to the ambient air as measured by an
applicable reference method, or an equivalent or alternate
method, specified in appendix M of 40 CFR Part 51 or by a test
method specified in the Washington state implementation plan SIP
(App. B).
Potential to Emit (WAC 173-400-030(62)) - The maximum capacity of a stationary source to emit a pollutant under its physical and operational design. Any physical or operational limitation on the capacity of the source to emit a pollutant, including air pollution control equipment and restrictions on hours of operation or on the type or amount of material combusted, stored, or processed, shall be treated as part of its design only if the limitation or the effect it would have on emissions is federally enforceable. Secondary emissions do not count in determining the potential to emit of a stationary source.
Prevention of Significant Deterioration (PSD) (WAC 173-400-030(63)) - The program set forth in WAC 173-400-141.
Rare and Endangered Plant Regeneration Fires (WAC 173-425-030(19)) - Fires necessary to promote the regeneration of rare and endangered plants found within natural area preserves as identified in chap. 79.70 RCW.
Reasonable Alternative - A method for disposing of organic refuse (such as natural vegetation) that is available, reasonably economical, and less harmful to the environment than burning.
Reasonably Available Control Technology (RACT) (WAC 173-400-030(66)) - The lowest emission limit that a particular source or source category is capable of meeting by the application of control technology that is reasonably available considering technological and economic feasibility. RACT is determined on a case-by-case basis for an individual source or source category taking into account the impact of the source upon air quality, the availability of additional controls, the emission reduction to be achieved by additional controls, the impact of additional controls on air quality, and the capital and operating costs of the additional controls. RACT requirements for any source or source category shall be adopted only after notice and opportunity for comment are afforded.
Recreational Fire - Cooking fires, campfires and bonfires using charcoal or firewood that occur in designated areas or on private property for cooking, pleasure, or ceremonial purposes. Fires used for debris disposal are not considered recreational fires.
Regulation - Any regulation and subsequently adopted
additions or amendments thereto of the Restated Regulation I 1 of
Yakima County Regional Clean Air Authority.
Regulatory Order (WAC 173-400-030(67)) - An order issued by ecology or the authority to an air contaminant source which applies to that source, any applicable provision of chap. 70.94 RCW, or the rules adopted thereunder, or the regulations of the authority.
Residential Burning - The outdoor Bburning consisting of
leaves, clippings, and prunings, and other yard and gardening
refuse originating on lands immediately adjacent and in close
proximity to a human dwelling and burned on such lands by the
property owner or his or her their designee.
Salvage Operation - An operation conducted in whole, or in
part, for the salvaging or reclaiming of any product or material.
Seasoned Wood (WAC 173-433-030(8)) - Wood of any species
that has been sufficiently dried so as to contain twenty percent
(≤20%) or less moisture by weight.
Second Stage of Impaired Air Quality - Can be declared by
the authority when particulate ten microns and smaller in
aerodynamic diameter PM10 is are at an ambient level of one
hundred and five 105 micrograms per cubic meter µg/m3 (App. B) of
air measured on a twenty-four 24 hour average.
Significant (WAC 173-400-030(68) & 40 CFR 52.21 (b)(23)(i)) - In reference to a net emissions increase or the potential of a
source to emit any of the following pollutants, a rate of
emission equal to or greater than ≥ (App. B) any one of the
following rates:
Pollutant | |||
100 | |||
40 | |||
40 | |||
25 | |||
15 | |||
40 | |||
0.6 | |||
Fluorides . . . . . . . . . . . . | 3 | ||
7 | |||
10 | |||
10 | |||
Municipal waste combustor organics . . . . . . . . . . . . (measured as total tetra-through octa-chlorinated dibenzo-p-dioxins and dibenzofurans) |
0.0000035 | ||
Municipal waste combustor metals (measured as PM) . . . . . . . . . . . . | 15 or 14 megagrams/yr | ||
Municipal waste combustor acid gases (measured as SO2 and |
40 or 36 megagrams/yr |
||
Municipal solid waste landfill emissions (measured as nonmethane organic compounds) . . . . . . . . . . . . |
50 or 45 megagrams/yr |
Silvicultural Burning - Burning on any land the Department
of Natural Resources protects per Chapter 70.94 RCW and pursuant
to Chapter 76.04 RCW. - Outdoor burning relating to the
following activities for the protection of life or property
and/or the public health, safety, and welfare:
1. Abating a forest fire hazard;
2. Prevention of a forest fire hazard;
3. Instruction of public officials in methods of forest fire fighting;
4. Any silivicultural operation to improve the forest lands of the state; and
5. Silvicultural burning used to improve or maintain fire dependent ecosystems for rare plants or animals within state, federal, and private natural area preserves, natural resource conservation areas, parks, and other wildlife areas.
Small Business - Any business enterprise employing twenty
(20) or less persons; the operation of which does not present any
potential hazard to public health.
Solid Fuel Burning Device (WAC 173-433-030(9)) - A device
that burns wood, coal, or other nongaseous or nonliquid fuels,
which includes any device burning any solid fuel except those
prohibited by WAC 173-433-120. This also includes any devices
used for aesthetic or space-heating purposes in a private
residence for commercial establishment which has a heat input
less than one million Btu per hour. In this regulation the
phrase "wood or coal heater" is intended to have the same meaning
as solid fuel burning device.
Source (WAC 173-400-030(70)) - All of the emissions unit(s), including quantifiable fugitive emissions, that are located on one or more contiguous or adjacent properties and are under the control of the same person or persons under common control whose activities are ancillary to the production of a single product or functionally related group of products. Activities shall be considered ancillary to the production of a single product or functionally related group of products if they belong to the same major group (i.e., which have the same two digit code) as described in the North American Industry Classification System (NAICS) as amended.
Stack (WAC 173-400-030(72)) - Any point in a source designed to emit solids, liquids, or gases into the air, including a pipe or duct.
Stack Height - The height of an emission point measured from
the ground-level elevation at the base of the stack.
Standard Conditions (WAC 173-400-030(74)) - A temperature of
20°C (68°F) and a pressure of 760 mm (29.92 inches) of mercury Hg
(App. B).
State Implementation Plan (SIP) (40 CFR 51.100(j)) - Plans required by EPA (App. B) to be submitted by ecology (App. B) to either maintain or obtain compliance with existing NAAQS (App. B) and approved or promulgated under section 110 of 172 of FCAA (App. B).
Stationary Source (WAC 173-400-030(75)) - Any building,
structure, facility or installation that which emits or may emit
any air contaminant. This term does not include emissions
resulting directly from an internal combustion engine for
transportation purposes or from a nonroad engine or nonroad
vehicle as defined in section 216 of the FCAA.
Storm and Flood Debris Burning - Outdoor burning of natural vegetation from storms or floods that have occurred in the previous two years and resulted in an emergency being declared or proclaimed in the area by the city, county, or state government.
Synthetic Minor (WAC 173-400-030(77)) - Any source whose potential to emit has been limited below applicable thresholds by means of a federally enforceable order, rule, or permit condition.
Threshold Level - The level that delineates whether or not a source must comply with specific requirements.
Toxic Air Pollutant (TAP) or Toxic Air Contaminant (WAC 173-400-030(80)) - Any class A or B toxic air pollutant listed in WAC 173-460-150 and 173-460-160. The term toxic air pollutant may include PM (App. B) and VOCs (App. B) if an individual substance or a group of substances within either of these classes is listed in WAC 173-460-150 and/or 173-460-160. The term toxic air pollutant does not include PM and VOCs as generic classes of compounds.
Treated Wood (WAC 173-433-030(10)) - Any species of wood that has been chemically impregnated, painted, or similarly modified to prevent weathering and deterioration.
Twenty-four (24) Hours (WAC 173-400-020(8)) - Any consecutive 24 hours starting at any clock hour.
Tumbleweed Burning - Outdoor burning to dispose of dry plants (typically Russian thistle and tumbleweed mustard plants), that have been broken off, and rolled about, by the wind.
Uncertified Wood Stove (WAC 173-433-030(2)) - A woodstove that does not meet emission performance standards when tested by an accredited independent laboratory or is not labeled according to procedures specified by EPA in 40 CFR Part 60, Subpart AAA, Standards of Performance for Residential Wood Heaters as amended through July 1, 1990.
Unclassifiable Area (FCAA, Sec. 107 (d)(1)(A)(iii) - Any area that cannot be classified on the basis of available information as meeting or not meeting the national primary or secondary ambient air quality standard for the pollutant.
Urban Growth Area - Land generally including and associated with an incorporated city which is designated by the county for urban growth under RCW 36.70A.030.
Volatile Organic Compound (VOC) (WAC 173-400-030(84)) -
includes: Any compound of carbon, excluding CO, CO2, carbonic
acid, metallic carbides or carbonates, and ammonium carbonate,
which participates in atmospheric photochemical reactions. This
includes:
1. Any such organic compound other except than the
following, which have been determined to have negligible
photochemical reactivity:
a. Methane;
b. Ethane;
c. Methylene chloride (dichloromethane);
d. 1,1,1-trichloroethane (methyl chloroform);
e. 1,1,1 2-trichloro 1,2,2-trifluoroethane (CFC-113);
f. Tricholorfluoromethane (CFC-11);
g. Dichlorodifluoromethane (CFC-12);
h. Chlorodifluoromethane (HCFC-22);
i. Trifluoromethane (HFC-23);
j. 1,2-dichloro 1,1,2,2-tetrafluoroethane (CFC-114);
k. Chloropentafluoroethane (CFC-115);
l. 1,1,1,-trifluoro 2,2-dichloroethane (HCFC-123);
m. 1,1,1,2-tetrafluoroethane (HFC-134a);
n. 1,1-dichloro 1-fluoroethane (HCFC-141b);
o. 1-chloro 1,1-difluoroethane (HCFC-142b);
p. 2-chloro 1,1,1,2-tetrafluoroethane (HCFC-124);
q. Pentafluoroethane (HFC-125);
r. 1,1,2,2-tetrafluoroethane (HFC-134);
s. 1,1,1-trifluoroethane (HFC-143a);
t. 1,1-difluoroethane (HFC-152a);
u. Parapchlorobenzotrifljouride PCBTF);
v. Cyclic, branched, or linear completely methylated siloxanes;
w. Acetones perchloroethylene (tetrachloroethylene); and
x. Perfluorocarbon compounds which fall into these classes:
1) Cyclic, branched, or linear completely flourinated alkanes;
2) Cyclic, branched, or linear completely flourinated ethers with no unsaturations; and
3) Sulfur containing perfluorocarbons with no unsaturations and with sulfur bonds only to carbon and fluorine.
2. For the purpose of determining compliance with emission
limits, VOC (App. B) will be measured by the appropriate methods
in 40 CFR Part 60 Appendix A. Where such a method also measures
compounds with negligible photo-chemical reactivity, these
negligibly-reactive compounds may be excluded as VOC if the
amount of such the compounds is accurately quantified, and such
the exclusion is approved by ecology or the authority.
3. As a precondition to excluding these negligibly-reactive compounds as VOC or at any time thereafter, ecology or the authority may require an owner or operator to provide monitoring or testing methods and results demonstrating, to the satisfaction of ecology or the authority, the amount of negligibly-reactive compounds in the source's emissions.
Weed Abatement Fire - Outdoor burning to dispose of weeds that is not regulated under chap. 173-430 WAC, which applies to agricultural burning.
Wood Heater - Has the same meaning as "solid fuel burning device."
Woodsmoke Control Zone - An area where the use of wood heaters and outdoor and agricultural burning is further restricted to reduce the impact of air pollution during an impaired air quality or air pollution episode. The legal land description is located in app. H, and it is shown on the map in app. I.
Wood Stove (WAC 173-433-030(11)) - An enclosed solid fuel burning device capable of and intended for residential space heating and domestic water heating that meets the following criteria contained in 40 CFR 60 Subpart AAA - Standards of Performance for Residential Wood Heaters as amended through July 1, 1990:
1. An air-to-fuel ratio in the combustion chamber averaging less than 35.0, as determined by EPA Reference Method 28A;
2. A useable firebox volume of less than 20 cubic feet;
3. A minimum burn rate less than 11 lbs./hr. (5 kg/hr) as determined by EPA Reference Method 28;
4. A maximum weight of 1764 lbs. (800 kg), excluding fixtures and devices that are normally sold separately, such as flue pipe, chimney, and masonry components not integral to the appliance.
A wood stove is a type of wood heater in this regulation. The term "wood stove" does not include wood cook stoves.
Yakima CO Nonattainment Area - The legal description is located in appendix H, and it is shown on the map in app. I.
Yakima PM10 Nonattainment Area - The legal description is located in appendix H, and it is shown on the map in app. I.
Yakima Urban Area - The legal land description is located in appendix H, and it is shown on the map in app. I.
Definitions of Acronyms and Abbreviations (New Appendix)
This appendix contains the definitions for acronyms and abbreviations used in more than one section of the regulation. Defined acronyms or abbreviations are identified with "(App. B)" in the text. The source is identified in italics.
ac. - Acre
ACM - Asbestos Containing Material.
AHERA - Asbestos Hazard Emergency Response Act also known as Title II of Toxic Substances Control Act (TSCA).
AOP - Air Operating Permit.
APCO - Air Pollution Control Officer.
ASIL - Acceptable Source Impact Level.
ASTM - American Society for Materials Testing.
BACT - Best Available Control Technology.
BMP - Best Management Practice.
BTU - British Thermal Unit.
cf - Cubic Feet.
CFR - Code of Federal Regulations
CO - Carbon Monoxide.
°C - Degrees Centigrade.
°F - Degrees Fahrenheit.
DNR - Washington State Department of Natural Resources.
DOA - Washington State Department of Agriculture.
DOT - Washington State Department of Transportation.
dscf - Dry Standard Cubic Foot.
dscm - Dry Standard Cubic Meter.
Ecology - Washington State Department of Ecology
EPA - U.S. Environmental Protection Agency.
ERC - Emission Reduction Credit(s).
FAA - Federal Aviation Administration.
f/cc - Fibers per cubic centimeter
FCAA - Federal Clean Air Act also know as Public Law 88-206, 77 Stat. 392, December 17, 1963, 42 U.S.C. 7401 et seq., as last amended by the Clean Air Act Amendments of 1990, P.L.. 101-549, November 15, 1990.
ft. - Feet.
GEP - Good Engineering Practice.
GIS - Geographic Information System.
HAP - Hazardous Air Pollutant.
HCl - Hydrogen Chloride.
Hg - Mercury.
hr. - Hour.
H2S - Hydrogen Sulfide.
H2SO4 - Sulfuric Acid.
IRS - Internal Revenue Service.
kg - Kilogram.
L&I - Washington State Department of Labor and Industries.
LAER - Lowest Achievable Emission Rate.
lbs - Pounds.
lbs./hr. - Pounds per Hour.
lbs./yr. - Pounds per Year.
lf - Linear Feet.
LP - Liquid Propane.
MACT - Maximum Available Control Technology.
m - Meter.
µg/m3 - Micrograms per Cubic Meter.
mg/m3 - Milligrams per Cubic Meter.
ml - Millileter.
mm - Millimeter.
MTBE - Methyl Tertiary Butyl Ether.
NAAQS - National Ambient Air Quality Standard.
NESHAPS - National Emission Standards for Hazardous Air Pollutants.
NF - National Forest.
NH3 - Ammonia.
NOC - Notice of Construction.
NOV - Notice of Violation.
NO2 - Nitrogen Dioxide.
NOx - Oxides of Nitrogen.
NPDES - National Pollution Discharge Elimination System.
NSPS - New Source Performance Standards.
NSR - New Source Review.
O2 - Oxygen.
O3 - Ozone.
OAPCA - Olympic Air Pollution Control Authority.
OSHA - Occupational Health and Safety Administration.
Pb - Lead.
PCE - Perchloroethylene.
PLM - Polarized Light Microscopy.
ppm - Parts per Million
PSCAA - Puget Sound Clean Air Agency.
PSD - Prevention of Significant Deterioration.
QA/QC - Quality Control/Quality Assurance.
RACT - Reasonably Available Control Technology.
RCW - Revised Code of Washington
SCAPCA - Spokane County Air Pollution Control Authority.
SEPA - State Environmental Policy Act, chap. 43.21c RCW & chap. 197-11 WAC.
sf - Square Feet.
SFBD - Solid Fuel Burning Device.
SIP - State Implementation Plan.
SO2 - Sulphur Dioxide.
SOX - Oxides of Sulphur.
SM - Synthetic Minor
TAP - Toxic Air Pollutant.
TPY - Tons per Year.
TRS - Total Reduced Sulfur Compounds.
TSP - Total Suspended Particulate.
UBC - Uniform Building Code.
USC - United States Code.
USDA - United States Department of Agriculture.
USDA-FS - U.S. Department of Agriculture, Forest Service.
UTM - Universal Transmercator
VOC - Volatile Organic Compound.
VOCs - Volatile Organic Compounds.
VP - Vapor Pressure.
WAC - Washington Administrative Code.
WCAA - Washington Clean Air Act, chap. 70.94 RCW.
YRCAA - Yakima Regional Clean Air Authority.
> - Greater Than.
< - Less Than.
≥ - Equal to or More Than.
≤ - Equal to or Less Than.
= - Equals.
Subject Index
This appendix contains an index by section and page numbers.
Abbreviations
Commonly used 1.07J1, 1-5
Definitions of abbreviations app. B, B-1->B-3
Definitions of words and phrases app. A, A-1->A-x,
Acronyms
Commonly used 1.07J2, 1-5
Definitions of acronyms app. B, B-1->B-3
Advisory Council 1.05D, 1-x
Agricultural Burning
Definition of app. A, A-2
Delegations (See Outdoor Burning, Delegations)
Exemptions
Limited 3.03G, 3-xx; table 3.03-1 and footnotes, 3-xx->3-yy
Specific 3.03H, 3-xx
General provisions 3.03C, 3-xx
Permits (See Permits, Outdoor and Agricultural Burning)
Prohibitions 3.03C1, 3-xx; 3.03Fl, 3-yy
Areas 3.03C1a->d, 3-xx->3-yy
Burning without a permit or limited exemption 3.03C1e & g, 3-xx
Hours 3.03C1f, 3-xx
Requirements 3.03C2, 3-xx->3-yy; 3.03F2, 3-zz
Additional 3.03C2g, 3-xx
Best management practice 3.03F2a, 3-xx
Cessation of burning 3.03C2e, 3-xx
Confirmation of daily burning status 3.03C2a, 3-xx
Demonstration of no reasonable alternative 3.03C2b, 3-xx
Extinguished fire 3.03C2f, 3-xx
Minimize adverse effects 3.03C2c, 3-xx
Natural vegetation 3.03F2c, 3-xx
Notification 3.03F2e, 3-xx; table 3.03-3, 3-yy
Other agencies 3.03C2h, 3-xx
Smoke dispersion 3.03F2d, 3-xx
Supervision of fire 3.03C2d, 3-xx
Types of tables 3.03-1->3, 3-xx->3-yy
Annual agricultural line 15
Fence row and windblown vegetation line 12
Irrigation or drainage ditches line 13
Orchard prunings line 14.1
Orchard removal line 14.2
Other agricultural line 16
Agricultural Land app. A, A-2
Agricultural Operation app. A, A-2
Ag Task Force app. A, A-2
Air Contaminant (Air Pollutant), app. A, A-2
Air Operating Permits 4.04, 4-x->4-y
Air Pollutant (Air Contaminat), app. A, A-2
Air Pollution app. A, A-2
Air Pollution Control Officer (APCO)
Delegated authority 1.05C, 1-x; 2.01B, 2-1
Powers and duties 2.01, 2-1
Air Pollution Episode 3.05C2, 3-xx; app. A, A-2
Allowable Emissions app. A, A-2
Altered Documents 1.07C, 1-5
Ambient Air app. A, A-3
Ambient Air Quality Standard app. A, A-3
Appeals 2.05, 2-x
Asbestos Control
Definitions
AHERA building inspector 3.07D1, 3-xx
AHERA project designer 3.07D2, 3-xx
Asbestos 3.07D3, 3-xx
Asbestos-containing material (ACM) 3.07D4, 3-xx
Asbestos project 3.07D5, 3-xx
Asbestos survey 3.07D6, 3-xx
Competent person 3.07D7, 3-xx
Component 3.07D8, 3-xx
Demolition 3.07D9, 3-xx
Facility 3.07D10, 3-xx
Friable asbestos-containing material 3.07D11, 3-xx
Glove bag 3.07D12, 3-xx
Leak-tight container 3.07D13, 3-xx
Nonfriable asbestos-containin material 3.07D14, 3-xx
Owner-occupied, single-family residence 3.07D15, 3-xx
Renovation 3.07D16, 3-xx
Suspect asbestos-containing material 3.07D17, 3-yy
Notification
Amendments 3.07G2, 3-xx
Emergencies 3.07G3, 3-xx
General requirements 3.07G1, 3-xx
Management of 3.07E, 3-xx
Procedures for projects
Alternative methods of compliance
Approval of alternate methods 3.07J4, 3-xx
Friable ACM 3.07J1, 3-xx
Leaving nonfriable ACM in place 3.07J3, 3-xx
Nonfriable ACM 3.07J2, 3-xx
Friable ACM 3.07I4, 3-xx
Nonfriable ACM 3.07I3, 3-xx
Training 3.07I1, 3-xx
Work practices 3.07I2, 3-xx
Removal
Demolition projects 3.07H2, 3-xx
Exceptions 3.07H3, 3-xx
Renovation projections 3.07H1, 3-xx
Surveys 3.07F, 3-xx
Waste material disposal
Prohibition 3.07K1, 3-xx
Temporary storage 3.07K3, 3-xx
Waste tracking requirements 3.07K2, 3-xx
Assurance Discontinuance 5.01F, 5-2
Authority 1.01, 1-1; 1.05A, 1-2; app. A, A-3
Best Available Control Technology (BACT) 4.02G2, 4-x; app. A, A-3
Best Management Practice (BMT) app. A, A-3
Board 1.05B, 1-x; 1.09B, 1-x; 1.09C, 1-y; 2.05B, 2-z; 2.01G, 2-2; app. A, A-3
Boilers
Bubble app. A, A-3
Burn Bans
Applicability 3.05B
Definition of app. A, A-3
Initiation
Air pollution episode 3.05C2, 3-xx; table 3.05-2, 3-xx
Impaired air quality 3.05C1, 3-yy; table 3.05-2, 3-xx
Exemptions
Outdoor and agricultural burning 3.05E1, 3-xx
Sole source of heat 3.05E2, 3-yy
Requirements
Fire training fires 3.05D2, 3-xx
Outdoor and agricultural burning 3.05D1, 3-xx
Wood heaters 3.04E3, 3-zz 3.05D3, 3-yy
Business Assistance Policy 1.03G, 1-x
Ceremonial Fires app. A, A-x
Class I Area app. A, A-x
Combustion and Incineration Sources
Definition of app. A, A-x
Incineration sources 3.01D2, 3-xx
Particulate matter 3.01D1, 3-xx
Commenced Construction app. A, A-x
Compliance 1.03C, 1-1; 1.07A, 1-x; art. 5, 5-1->5-x
Concealment
Definition of app. A, A-x
Prohibition against (See Emission Standards, General Standards, Concealment and Masking)
Construction/Demolition Debris app. A, A-x
Control Apparatus app. A, A-x
Corrective Action Order 5.01C, 5-1; app. A, A-x
Cross Reference to Restated Regulation I app. E, E-1->E-12
Criteria Pollutant app. A, A-x
Daylight Hours app. A, A-x
De Minimis app. A, A-x
Definitions 1.07J, 1-5, app. A, A-x->A-y
DEQ Phase 2 Woodstove app. A, A-x
Disclaimer 1.07I, 1-5
Dust
Cattle Feeding Operations 3.08B, 3-xx
Construction 3.08A, 3-xx
Fugitive 3.01C2c. 3-x app. A, A-x
Effective Date 1.08, 1-6
Eight Hours app. A, A-x
Enforcement art. 5, 5-1->5-x
Emission Reduction Credits (ERC) app. A, A-x
Emissions
Definition of app. A, A-x
Excess
Definition of app. A, A-x
Requirements 3.11D3, 3-xx
Fugitive app. A, A-x
Mobile sources
Particulate matter (PM) app. A, A-x
PM10 app. A, A-x
Stationary sources
Point
Voluntary limits 4.05, 4-x
Emissions Sampling
Ambient air monitoring 3.11E1, 3-x
Compliance testing 3.11E2, 3-x
Continuous monitoring and recording 3.11F, 3-x
Emission inventory 3.11E3, 3-x
Emissions Standards
Additional standards for
Certain sources 3.01F, 3-xx
Catalytic cracking units 3.01F4, 3-x
Grain elevators 3.01F3, 3-x
Hog fuel boilers 3.01F1, 3-x
Orchard heating 3.01F2, 3-x
Sewage sludge incinerators 3.01F6, 3-x
Sulfuric acid plants 3.01F5, 3-x
Combustion and incineration sources
Incineration sources 3.01D2, 3-xx
Particulate matter (PM) 3.01D1, 3-xx
General process sources 3.01E, 3-zz
Definition of app. A, A-x
Dry cleaners, perchloroethylene (PCE) 3.02D, 3-xx
General Standards
Concealment and masking 3.01C1g, 3-xx
Detrimental emissions 3.01Cle, 3-zz
Exemptions 3.01C3, 3-x
Agricultural odors 3.01C3a, 3-x
Ammonia emissions from fertilizer 3.01C3b, 3-x
Fugitive dust sources 3.01C2c, 3-z
Odors 3.01C1d, 3-x
Opacity measurement 3.01C2d, 3-x
Particulate matter 3.01C1b, 3-x
Reasonable precautions 3.01C1c, 3-x
Reasonably available control technology 3.01C2b, 3-x
Sulfur dioxide 3.01Clf, 3-y
Sale or installation of air pollution source 3.01C1h, 3-x
Two or more emission units 3.01C2a, 3-x
Visible emissions 3.01C1a, 3-xx
Measurable emissions standards app. D, D-1->D-3
National emissions standards for hazardous air pollutants app. A, A-x
Sources of hazardous air pollutants 3.02, 3-x;
Perchloroethylene (PCE) dry cleaners 3.02D, 3-x
Emissions Unit app. A, A-x
Equipment app. A, A-x
EPA Certified Woodstove
EPA Exempted Device
Excess Emissions (See Emissions, Excess)
False or Misleading Information 1.07B, 1-4->1-5
Farmer app. A, A-x
Fees
Charges 2.02B, 2-x
Fees schedules
Adoption 2.02D1, 2-x
Availability 2.02D2, 2-x
Legal authority 2.02A, 2-y
Refunds 2.02C, 2-x
Federal Regulations 2.03B, 2-x
Fire Department
Fire Fighting Training Fires 3.03E, 3-zz; app. A, A-x
Fireplace app. A, A-x
Fossil Fuel-fired Steam Generator app. A, A-x
Furnace app. A, A-x
Garbage app. A, A-x
General Applicability 1.04, 1-2
General Provisions 1.07, 1-4->1-5; art. 2, 2-1
General Process Source app. A, A-x
General Rule Permits
Requirements 3.03J3, 3-x
Types (See Permits, General Rule)
Good Agricultural Practices app. A, A-x
Good Engineering Practice app. A, A-x
Hazardous Air Pollutant 3.02, 3-xx; app. A, A-x, app. L, L-1->L-9
Hearings Board
Home Barbecues app. A, A-x
Hour app. A, A-x
Impaired Air Quality app. A, A-x
First Stage (Yellow) app. A, A-x
Second Stage (Red) app. A, A-x
Incinerator app. A, A-x
Injunctive Relief 5.01E, 5-1
Investigations 2.01C, 2-1
Land Clearing Burning app. A, A-x
Legal Action 2.01G, 2-2
Legal Land Descriptions
Woodsmoke Control Zone app. H, H-1
Yakima CO Nonattainment Area app. H, H-4
Yakima PM10 Nonattainment Area app. H, H-4
Yakima Urban Area app. H, H-1->H-3
Lowest Achievable Emission Rate (LAER) 4.02G2, 3-xx; app. A, A-x
Maintenance
Major Modification app. A,
Maps
Woodsmoke Control Zone app. I, I-2
Yakima CO Nonattainment Area app. I, I-4
Yakima PM10 Nonattainment Area app. I, I-5
Yakima Urban Area app. I, I-3
Materials Handling app. A, A-x
Maximum Available Control Technology (MACT) app. A, A-x
Modification app. A, A-x
Monitoring, Recordkeeping, and Reporting 3.11, 3-xx
Additional monitoring requirement 3.11D6, 3-xx
Change in raw material or fuels for non-AOP source 3.11D4, 3-yy
Excess emissions 3.11D3, 3-zz
Monitoring records 3.11D4, 3-xx
Natural Vegetation app. A, A-x
Net Emissions Increase app. A, A-x
New Source app. A, A-x
New Source Performance Standards (NSPS) app. A, A-x
New Source Review (NSR)
Applicability 4.02B, 4-5->4-x
Application
Definition of app. A, A-x
Requirements
Additional requirements for stationary sources 4.02E, 4-8
Additional requirements for temporary sources 4.02I, 4-8
All sources 4.02D, 4-7
Approval requirements
Additional requirements for stationary sources 4.02H, 4-10
Additional requirements for temporary sources 4.01I, 4-11
All sources 4.02G, 4-8
Changed conditions 4.02J, 4-yy
Definition of app. A, A-x
Exemptions 4.02C, 4-6->4-x; app. K
Based on emission thresholds 4.02C2, 4-x
Emission unit and activity exemptions for nontoxic pollutants app. K, para. A, K-1
Environmental chambers and laboratory equipment app. K, para. A6, K-2
Maintenance/construction app. K, para. A1, K-1
Material handling app. K, para. A4, K-2
Miscellaneous app. K, para. A8, K-3
Monitoring/quality assurance/testing app. K, para. A7, K-2->K-3
Projects with combined heat inputs ≤ specific levels app. K, para. A3, K-2
Storage tanks app. K, para. A2, K-2
Water treatment app. K, para. A5, K-2
Toxic air pollutants app. K, para. B, K-4
Class A TAP app. K, para. B1, K-4->K-14
Class B TAP app. K, para. B2, K-14->K-36
SEPA compliance 4.02G1, 4-8
New Wood Stove app. A, A-x
Nonattainment Area app. A, A-x
Nonscheduled Renovation Operation
Notice of Construction (See New Source Review)
Nuisance app. A, A-x
Odors
Objectionable odors
Exemptions
Ozone (O3) 3.06, 3-xx
Opacity
Definition of app. A, A-x
Measurement
Standards
Catalytic cracking units
Orchard heaters
Wood heaters
Operation and Maintenance 3.00E, 3-x
Order(s)
Availability 1.07D, 1-5
Corrective action 5.01C, 5-1
Definition of app. A, A-x
Order of Approval app. A, A-x
Prohibitory 5.01D, 5-1
Regulatory
Conditions 4.05C, 4-y
Definition of app. A, A-x
Outdoor Burning
Cessation of burning
Definition of app. A, A-x
Delegations
To the authority 3.03B, 3-xx; table 3.03-2 and footnotes, 3-xx->3-yy
From the authority 3.03I, 3-xx; table 3.03-2 and footnotes, 3-xx->3-yy
Exemptions
Limited 3.03G, 3-xx; table 3.03-1 and footnotes, 3-xx->3-yy
Specific 3.03H, 3-xx
General provisions 3.03C, 3-xx
Permitting (See Permits, Outdoor and Agricultural Burning)
Prohibitions 3.03C1, 3-xx; 3.03D1, 3-yy
Areas 3.03C1a->d, 3-xx
Burning without a permit or limited exemption 3.03C1e & g, 3-xx
Hours of burning 3.03C1f, 3-xx
Materials 3.03D1a, 3-xx
Requirements 3.03C2, 3-xx->3-yy; 3.03D2, 3-zz
Additional 3.03C2g, 3-xx
Cessation of burning 3.03C2e, 3-xx
Confirmation of daily burning status 3.03C2a, 3-xx
Demonstration of no reasonable alternative 3.03C2b, 3-xx
Extinguished fire 3.03C2f, 3-xx
Fire fighting training fires 3.03E, 3-xx
Ignition 3.03D2a1), 3-xx
Notification 3.03D2a2), 3-xx; table 3.03-3, 3-xx
Minimize adverse effects 3.03C2c, 3-xx
Other agencies 3.03C2h, 3-xx
Residential 3.03D2b, 3-xx
Storm and flood debris 3.03D2c, 3-xx
Supervision of fire 3.03C2d, 3-xx
Types of Fires
Ceremonial fires app. A, A-x
Fire fighting training fires 3.03E, 3-xx; app, A-x
Aircraft crash rescue 3.03E4, 3-xx
Flammable liquids training fires GRP 3.03-3, 3-xx
Other training fires GRP 3.03-4, 3-zz
Structural fire training inside of urban growth areas 3.03E, 3-xx
Structural fire training outside of urban growth areas GRP 3.03-1, 3-xx
Wildland fire training fires GRP 3.03-2, 3-zz
Land clearing app. A, A-x
Other outdoor burning app. A, A-x
Rare & endangered plant regeneration fires app. A, A-x
Recreational
Definition of app. A, A-x
Home barbecues app. A, A-x
Large recreational
Other recreational
Residential app. A, A-x
Silvicultural app. A, A-x
Storm and flood debris app. A, A-x
Tumbleweed app. A, A-x
Weed abatement app. A, A-x
Particulate Matter (PM) Emissions (See Emissions, Particulate Matter)
Parts per Million (ppm) app. A, A-x
Pellet Stove app. A, A-x
Penalties
Aiding and abetting 5.02F, 5-2
Civil 5.02D, 5-2
Criminal 5.02C, 5-2
Determination 5.02J, 5-3
Disbursement 5.02H, 5-2
Interest on 5.02E, 5-2
Under-reporting 5.02G, 5-3
Withholding grants 5.02I, 5-3
Permits
Administrative 4.07, 4-x
Air operating 4.04, 4-x
Fees 3.03K, 3-xx
Outdoor and agricultural burning
Application 3.03J7, 3-zz
Annual 3.03J2, 3-xx
Cancellation 3.03F2f, 3-xx
Conditions 3.03J4, 3-xx, 3.03J6, 3-yy
Delegations
Permits issued by agents 3.03I2, 3-xx; table 3.03-2, 3-xx
Permitting by other agencies 3.03I1, 3-yy; table 3.03-2, 3-xx
Duration 3.03J5, 3-xx
Individual 3.03J1, 3-xx
General rule 3.03J3, 3-yy
Not Required
Agricultural burning table 3.03-1, 3-yy
Fence rows and windblown vegetation line 12
Irrigation or drainage ditches line 13
Orchard prunings line 14.1
Outdoor burning table 3.03-1, 3-xx
Aircraft crash rescue training line 2.5
Home barbecues line 5.3
Other recreational line 5.2
Tumbleweed line 9
Training fires inside a fire training facility line 17
Required
Agricultural table 3.03-1, 3-xx
Annual line 15
Orchard removal line 14.2
Other line 16
Outdoor burning table 3.03-1, 3-xx
Ceremonial line line 1
Fire fighting training fires
By general rule permit lines 2.12->2.4, 3-xx
By individual permit line 2.11, 3-xx
Land clearing fires line 3
Other outdoor line 11
Large recreational line 5.1, GRP 3.03-5, 3-xx->3-yy
Rare and endangered plant regeneration line 4
Residential line 6
Storm or flood debris line 8
Weed abatement line 10
Types of
Individual 3.03J1, 3-xx
Annual 3.03J2, 3-yy
General rule 3.03J3, 3-zz
Flammable liquids training fires GRP 3.03-3, 3-xx
Large recreational fires GRP 3.03-5, 3-xx
Other training fires GRP 3.03-4, 3-zz
Structural fire training outside of urban growth areas GRP 3.03-1, 3-xx
Wildland fire training fires GRP 3.03-2, 3-zz
Person app. A, A-x
PM2.5 app. A, A-x
PM10 app. A, A-x
PM10 Emissions (See Emissions, PM10)
Policy 1.03, 1-1
Posting of Notices 1.07E, 1-5
Potential to Emit app. A, A-x
Prevention of Significant Deterioration (PSD) app. A, A-x
Public Comments 2.02D-1, 2-x, 2.04D4, 2-x, 2.04D6, 2-z
Public Hearings 2.04D5, 2-x
Public Participation 2.04, 2-x
Public Notice Process 2.04D, 2-z
Public Policy 1.03A, 1-1
Reasonable Alternative 3.03C2b, 3-xx; app. A, A-x
Reasonably Available Control Technology (RACT) 3.01C2b, 3-xx; app. A, A-x
Records 1.06, 1-x; 2.01E, 2-x
Confidential 1.06D, 1-4
Maintain 2.01E, 2-2
Public 1.06C, 1-3->1-4
Requests for 1.06C3, 1-4
Recordkeeping (See Monitoring, Recordkeeping, and Reporting)
Registration
Applicability 4.01B, app. G, G-1->G-x
Exemptions
Air operating permit sources 4.01D1, 4-1
Criteria exempt sources 4.01D2, 4-1
Gasoline marketing operations 4.01D4, 4-1
Toxic air pollutant source 4.01D3, 4-1; app. K, para. B, K-4->k-36
Limited exemptions 4.01E, 4-2
Procedure 4.01F, 4-2->4-x
Responsibility 4.01C, 4-1
Regulation app. A, A-x
Reporting (See Monitoring, Recordkeeping, and Reporting)
Revisions 1.07H, 1-5
Revocations 1.09, 1-6
Right to Obtain Samples 2.01D, 2-x
Roles and Responsibilities 1.05, 1-2
Advisory Council 1.05D, 1-3
Air Pollution Control Officer 1.05C, 1-3
Authority 1.05A, 1-2
Board of Directors, 1.05A, 1-2->1-3
Seasoned Wood app. A, A-x
Severability 1.07F, 1-5
Significant app. A, A-x
Significant Visibility Impairment app. A, A-x
Signing Authority 2.01F, 2-2
Solid Fuel Burning Device (See Wood Heaters)
Source
Definition of app. A, A-x
Major stationary app. A, A-x
Minor app. A, A-x
Mobile
Stationary
Synthetic minor (SM)
Temporary
Stack app. A, A-x
Standard Conditions app. A, A-x
State Regulations 2.03A, 2-x
State Implementation Plan (SIP) 1.03I, 1-2, app. A, A-x
State Environmental Policy Act (SEPA) 1.03H, 1-2; 4.02G1, 4-x
Stationary Source app. A, A-x
Synthetic Minor
Definition of app. A, A-x
Status 4.05B1, 4-x
Threshold Level app. A, A-x
Toxic Air Pollutant (TAP) app. A, A-x; app. K, K-4->K-36
Treated Wood app. A, A-x
Twenty-four (24) Hours app. A, A-x
Uncertified Wood Stove app. A, A-x
Unclassifiable Area app. A, A-x
Urban Growth Areas (UGA) app. A, A-x
Variances
Conditions for Granting 3.00D4, 3-x
Emergency Provisions 3.00D9, 3-z
Expiration 3.00D6. 3-x
Judicial Review 3.00D8, 3-z
Limitations 3.00D5, 3-x
Renewals 3.00D7, 3-z
Requests 3.00D3, 3-x
Volatile Organic Compound (VOC) app. A, A-x
Waiver 1.07G, 1-5
Wood Heater
Definitions of app. A, A-
Limited exemptions
Antique wood stoves and heaters 3.04D3, 3-xx
Boilers 3.04D1, 3-xx
Existing uncertified 3.04D5, 3-xx
Furnaces 3.04D2, 3-xx
Historical sites 3.04D4, 3-xx
Prohibited fuel types 3.04E2, 3-xx
Opacity 3.04E1, 3-xx
Nuisance standards 3.01C1d, 3-xx; 3.01C1e, 3-yy; 3.04E4, 3-zz
Sales, advertisement, and installation 3.04C, 3-xx
Use during burn bans 3.04E3, 3-xx
Woodsmoke Control Zone
Definition of app. A, A-x
Legal land description app. H, H-1
Map location app. I, I-2
Written Notice 5.00D, 5-1
Yakima CO Nonattainment Area
Definition of app. A, A-x
Legal land description app. H, H-4
Map location app. I, I-4
Yakima PM10 Nonattainment Area
Definition of app. A, A-x
Legal land description app. H, H-4
Map location app. I, I-5
Yakima Urban Area
Definition of app. A, A-x
Legal land description app. H, H-1->H-3
Map location app. I, I-3
Measurable Emissions Standards for Various Sources (New Appendix)
This appendix contains specific information about the measurable emissions standards cited in other sections. 1/
Sub. No. a |
Standard | Test Method d |
Compli- ance Assur- ance e |
|
Type b |
Emission Limit c |
|||
Visible Emissions | ||||
3.01C1a 3.01C1a1) |
General Standard Hog fuel boilers |
≤ 20% opacity measured for 3
min. in a 1 hr. period. ≤ 20% opacity except for 15 consecutive min. in any 8 hr. period. |
EPA Method 9, 40 CFR
Part 60, App. A. and
Ecology Method. 9A, 5/ EPA Method 9, 40 CFR Part 60, App. A. |
2/, 3/, 4/ 2/, 3/ |
3.01F 3.01F1 3.01F2 3.01F4a 3.01F4b 3.04E1 |
Certain Sources Hog fuel boilers Orchard heating Existing catalytic cracking units New catalytic cracking units Wood Heaters |
See 3.01C1a1) ≤20% opacity except during the first 30 min. after ignition. ≤40% opacity for 3 min. in a 1 hr. ≤ 20% opacity for 3 min. in a 1 hr. period. 7/ ≤ 20% opacity for 6 min. in a 1 hr. period. 8/ |
EPA Method 9, 40 CFR Part 60, App. A. EPA Method 9, 40 CFR Part 60, App. A. and Ecology Method 9A. 5/ EPA Method 9, 40 CFR Part 60, App. A. and Ecology Method. 9A, 5/ EPA Method 9, 40 CFR Part 60, App. A and Ecology Method 9B. 5/ |
3/, 4/ 3/, 4/, 6/ 3/, 4/, 6/ 3/ |
PM | ||||
3.01D1 3.01D1a 3.01D1b |
Comb. & Incin.
Sources Wood derived fuels for steam production All other fuels |
≤ 0.46 gram/dscm or ≤ 0.2 grain/dscf of exhaust gas. 9/, 10/ ≤ 0.23 gram/dscm or ≤ 0.1 grain/dscf of exhaust gas. 9/, 10/ |
EPA Method 5, 40 CFR Part 60, App. A. EPA Method 5, 40 CFR Part 60, App. A. |
4/, 11/ 4/, 11/ |
3.01E | General Process Sources | ≤ 0.23 gram/dscm or ≤ 0.1 grain/dscf of exhaust gas. 9/, 10/, | EPA Method 5, 40 CFR Part 60, App. A. | 4/, 11/ |
SO2 | ||||
3.01C1f | General Standard | ≤ 1,000 ppm. 9/, 10/, 12/ | EPA Method 6, 40 CFR Part 60, App. A. | 2/, 4/, 13/ |
VOCs | ||||
3.01D2 | Incineration Sources. | ≤ 100 ppm. | EPA Method 18, 40 CFR Part 60, App. A. | 2/, 4/, 13/ |
H2SO4 | ||||
3.01F 3.01F5 |
Certain Sources H2SO4 plants |
≤0.15 lbs./ton of acid produced. 14/ |
EPA Method 8, 40 CFR Part 60, App. A. |
4/, 13/ |
NOx | ||||
3.01 | Any source | 15/ | EPA Method 7E, 40 CFR Part 60, App. A. | 4/, 13/ |
1/ When an emission standard is not cited, the user needs to review 40 CFR Parts 60, 61, and 63 for an appropriate standard.
2/ When monitoring is required by conditions established in a NSR approval, order, or permit, the monitoring shall be at least once per three months or more frequently if ordered.
3/ Test performed by a currently certified opacity reader.
4/ Minor sources shall maintain the records of these tests for two years unless ordered otherwise by the
APCO. Major sources shall maintain the records for five years.
5/ "Source Test Manual Procedure for Compliance Testing", State of Washington, Department of Ecology.
6/ Continuous emissions monitoring required as specified by 40 CFR Part 60 Subpart J, Sec. 60.105
7/ Unless a lower standard is established during a NSR..
8/ Except during the start of a new fire for a period ≤ 20 min. in any four hr. period.
9/ (5.07C) Stated Concentrations for combustion and incineration sources will be determined calculated after the volumes are
corrected to seven percent (7%) O2 (App. B) oxygen except when the authority decides that an alternate O2 correction factor is more
representative of normal operations.
10/ At standard conditions (App. A.)
11/ When monitoring is required by conditions established in a NSR approval, order, or permit, the monitoring shall be at least once per five years or more frequently if ordered.
12/ Calculations based on the average of any period of 60 consecutive minutes.
13/ Existing sources are subject to the compliance assurance requirements of 40 CFR Part 60.
14/ Expressed as 100% H2SO4.
15/ The emission limits for NOx shall be determined in the BACT analysis.
Notes
1. Alternative test procedures must either:
a. Have received advance written approval from the authority in accordance 40 CFR 51.212, or
b. Be acceptable procedures contained in "Source Test Manual Procedure for Compliance Testing", State of Washington, Department of Ecology.
Cross Reference Between Restated Regulation I of 1995 and Regulation 1 (New Appendix)
SECTION & SUBSECTION NO. |
COMMENTS | ||
EXISTING | PROPOSED | ||
ARTICLE I | |||
Section 1.01 | 1.03 | Reference to cooperation w/ YIN was removed. | |
Section 1.02 | 1.02 | ||
Section 1.03 | App. A App. H |
Common definitions used in more than one section. Specific definitions used in only one section is in that section. Legal land descriptions for Woodsmoke Control Zone, Yakima Urban Area, & Yakima PM10 Nonattainment Area are in App. H. |
|
ARTICLE II | |||
Section 2.01 | 1.04 | Rewritten extensively. | |
2.01 | |||
Section 2.02 | |||
2.02A | 1.05C | ||
2.02B | 2.01C 2.01E |
||
2.02C | 2.01C1->2 | 2.01C3&4 deleted. Authority will use RCW 70.94.200 if needed. | |
2.02D | 2.01D1->3 | Split into subsections. | |
2.02E | 2.01A3 | Powers broadened to include unless limited by the board. | |
Section 2.03 | |||
2.03A | 1.07B | ||
2.03B | 1.07C | ||
2.03C | 1.07D | ||
2.03D | 1.07E | ||
Section 2.04 | 1.06C1&2 | Rest of 1.06 is a new section. | |
Section 2.05 | 1.05D | ||
Article III | |||
Section 3.01 | 5.01 | ||
Section 3.02 | ----- | Not included. Use state law and WAC. | |
Section 3.03 | ----- | Not included. Use state law and WAC. | |
Section 3.04 | 2.05C3 | ||
ARTICLE IV | |||
Section 4.01 | |||
4.01A | 4.01B App. G, ¶A&B |
||
4.01B | 4.01F5 | ||
4.01C | ------- | No longer applicable technology. | |
4.01D | 4.01C | ||
4.01E | 4.01F1&2 | ||
4.01F | 4.01F1d | ||
4.01G | 4.01F4 | ||
4.01H | 4.01G | Fee schedules not included in the regulation. | |
Section 4.02 | 4.02 | ||
4.02A | 4.02B | ||
4.02B | 4.02E5a | ||
4.02C | 4.02E5b | ||
4.02D 4.02D1 4.02D2 4.02D3 |
4.02E3 4.02F2 4.02E4 4.02F6 4.02F3 4.02F1a 4.02F1b |
||
4.02E | 4.02F1c->e | ||
4.02F | 4.02F8&9 | ||
4.02G | 4.02D | ||
4.02H 4.02H1a&c 4.02H1b 4.02H2 |
2.04 2.04D 2.04D & 4.02E2 |
Now in a general regulation for all authority activities. Deleted. No longer correct. |
|
4.02I | 4.02E & App. F, ¶ C |
||
Section 4.03 | 4.01D, 4.01E, & 4.02C | ||
4.03A | |||
4.03B | |||
4.03C | |||
4.03D | |||
4.03E | |||
4.03F | |||
4.03G | |||
4.03H | |||
4.03I | |||
4.03J | |||
4.03K | |||
4.03L | |||
ARTICLE V | |||
Section 5.01 | 3.03C2c, tab. 3.03-1 & 2 |
||
5.01A | 3.03I | ||
5.01A1 5.01A2 5.01A3 |
tab. 3.03-2 ---------- tab. 3.03-2 |
Requirement dropped. |
|
5.01B | 3.03B | This section is not applicable to silvicultural burning. | |
5.01C | tab. 3.03-2 | ||
5.01D | 1.07A | ||
5.01E | 5.01K | ||
Section 5.02A | 3.03B | Similar language. | |
5.02A1 | 3.03C1, 3.03D1, & 3.03F1 |
||
5.02A1a | 3.03D1a & 3.03F2b | ||
5.02A1b & 5.02A1c |
3.03C2f(1) & 3.05C2a | ||
5.02B | ----- | Subsection deleted. | |
Section 5.03 | |||
5.03A | 3.03A | ||
5.03B | 3.03C1c | Added the city of Sunnyside to recognize the existing city ordinance. | |
5.03C 5.03C1 5.03C2 |
3.03C1b(2) _______ 3.03C2b) |
Not needed. Covered by 3.03Clc |
|
5.03D 5.03D1 5.03D2 5.03D3 |
3.03C2c(1) & tab. 3.03-2 tab. 3.03-1&2 tab. 3.03-1&2 tab. 3.03-1&2 |
Reference to flares, torches, gas burners, incense burners, & insect pots dropped. |
|
5.03Da->f | 3.03E1, 2, & 3 & GRP No. 3.03 - 1 |
||
Section 5.04 | |||
5.04A | 3.03C,D, E, & F | ||
5.04A1 | tab. 3.03-1 | ||
5.04A1a | N/A | Offering farmers the choice of a annual permit or specific burning permits. |
|
5.04A1b | tab. 3.03-1 | Deleted requirement for certification by an agricultural extension agent. |
|
5.04A2 | tab. 3.03-1&2 & GRP No. 1 -> 4 | ||
5.04B | 3.03C2d | ||
5.04C | 3.03C2d | ||
5.04D | 3.03C2b | ||
Section 5.05 5.05 Last sentence |
3.03C1 &
3.03D2a(1) 3.03C2g |
Exemptions are in Table 3.03-1. Adds "no smoke" to the definition for an extinguished fire. |
|
5.05A 5.05A1 |
3.03C2f(1) 3.05C2a 3.03Cf(2)->(4) |
||
5.05B | 3.03C2i | ||
Section 5.06 | 3.01B 3.01C2a 3.01C2b |
||
5.06A 5.06A1 5.06A2 5.06A3 |
3.01C1a 3.01C1a(1) 3.01C1a(2) 3.01C1a(3) & 3.04D1a |
||
5.06B | 3.01C1b(1) | ||
5.06C | 3.01C2c | ||
5.06D | 3.01C1c | ||
5.06E | 3.01C1d | ||
5.06F 5.06F1 5.06F2 |
3.01C1e 3.01C1e(1) 3.01Cle(2) |
||
5.06G | 3.01C1f | ||
5.06H 5.06H1 5.06H2 |
3.01C2d 3.01C2d(1) 3.01C2d(2) |
||
5.06I | 3.01C1g | ||
5.06J | 3.01C2e | ||
Section 5.07 | 3.01D | ||
5.07A | 3.01C1a | ||
5.07B | App. D, VOC & Footnote 8 | ||
5.07C | App. D, Footnote 5 |
||
5.07D | 3.01D2c | ||
5.07E | 3.01E2 | ||
Section 5.08 | 3.01E2 | ||
Section 5.09 | 3.01F | ||
5.09A 5.09A1 5.09A2 |
4.02D or E&F N/A 4.02D4 or 4.02F1 |
Will be a requirement of NSR or temporary permitting under section 4.02. |
|
5.09B 5.09B1 5.09B2 5.09B3 |
3.01F1 3.01C1a(1) 3.01C2b & 3.00F1 3.01F1a->c |
||
5.09C 5.09C1 5.09C2 |
3.01F2a 3.01F2a App. D |
||
5.09D 5.09D1 5.09D2 |
3.01F3 N/A 3.01F3 |
No longer needed. |
|
5.09E 5.09E1 5.09E2 5.09E3 5.09E4 |
3.07 3.07->K 3.07 3.07F App. F, ¶ E |
This is a total rewrite patterned after the SCAPCA Sect. 9.01 -> 9.08 Fee schedule corrected to remove errors in the old reg. |
|
5.09F | ------- | Deleted. Obsolete technology. | |
5.09G 5.09G1 5.09G2 |
3.01F4 App. D 3.01F4b |
||
5.09H1 5.09H2 |
3.01C 3.01C2b & App. D |
||
Section 5.10 | ------- | Deleted. This section has not been used and there is no foreseeable use for it. | |
Section 5.11 | 3.11 | Some text in 2.01. | |
5.11A | 3.11E1a&b | ||
5.11B | 2.01D1 | Reference to 2.01D in subsection 3.11E2b2) | |
5.11C | 3.11E2 | Deleted the requirement for a owner/operator to provide a sampling platform or ports. | |
5.11D | 3.11D2 | Rewritten to conform to WAC 173-400-107. | |
5.11E 5.11E1->4 5.11E5 |
3.11F 3.11F2 & Table 3.11-1 3.11F5 |
||
5.11F | 3.11F3b | 18 month time requirement for installation removed. | |
5.11G | 3.11F6 | ||
5.11H | 3.11F4 | ||
5.11I | 3.11D4 | ||
5.11J | 3.11E3 | ||
5.11K | 3.11D3 | ||
Section 5.12 | 3.01 | ||
5.12A | 3.01C1b(2) | ||
5.12B | 3.01C1b(3) | ||
5.12C | 1.07H | ||
5.12D | 3.08A4f | ||
ARTICLE VI | |||
Section 6.01 | 4.04A | ||
Section 6.02 | 4.04J & App. F, ¶ F |
||
ARTICLE VII | |||
Section 7.01 | 3.00E | ||
7.01A 7.01A1 7.01A2 7.01A3 7.01A4 |
3.00E2 3.00E3e(1) 3.00E3e(2) 3.00E6 3.00E7 |
||
7.01B | 3.00E3b | ||
7.01C 7.01C1 7.01C2 7.01C3 |
3.00E4 3.00E4a 3.00E4b --------- |
Duplicated by other subsections. |
|
7.01D | 3.00E8 | ||
7.01E | 3.00E9 | ||
7.01F | 3.00E10 | ||
7.01G | 3.00E3c | ||
ARTICLE VIII | Article 5 | ||
Section 8.01 | 5.02 | ||
8.01A | ---- | Deleted. Refer to Chap. 70.94 RCW. | |
8.01B | ---- | Deleted. Refer to Chap. 70.94 RCW. | |
8.01C | ---- | Deleted. Refer to Chap. 70.94 RCW. | |
8.01D | ---- | Deleted. Refer to Chap. 70.94 RCW. | |
Section 8.02 | 5.02 | ||
8.02A | 5.02D1&2 | ||
8.02B | 5.02E | ||
8.02C | 5.02F | ||
8.02D | 5.02G | ||
8.02E | 5.02H | ||
8.02F | 5.02J | Delete table on Pg. 8-3. | |
8.02G | 5.02I | ||
Section 8.03 | 5.01F | ||
Section 8.04 | 5.01E | ||
Section 8.05 | 1.07G | ||
ARTICLE IX | |||
Section 9.01 | 3.04A | ||
Section 9.02 | 3.04E1 and App. D | Reference to 10% opacity standard for education dropped. | |
Section 9.03 | 3.04E2 | ||
Section 9.04 | |||
9.04A | 3.04D1 | Definitions of certified stoves removed because this is a UBC requirement. Definitions are still in appendix A. | |
9.04B | 3.04D1 | Definitions of certified stoves removed because this is a UBC requirement. Definitions are still in appendix A. | |
9.04C | 3.04D1 | Definitions of certified stoves removed because this is a UBC requirement. Definitions are still in appendix A. | |
9.04D | 3.04D2 | ||
9.04E | 3.04C | ||
Section 9.05 | 3.05 | ||
9.05A 9.05A1 9.05A2 9.05A3 |
3.05B & 3.05D2 3.05C2b & tab. 3.05-1 tab. 3.05-1 & 3.05C1a(1) tab. 3.05-1 & 3.05C1a(2) |
||
ARTICLE X | |||
Section 10.01 | 3.06 | ||
ARTICLE XI | 1.08 | ||
ARTICLE XII | 2.03 | ||
Section 2.01 | 2.03A | ||
Section 12.02 | 2.03B | ||
ARTICLE XIII | |||
Section 13.01 | ______ | Not included in the regulation. Fees will be adopted by board resolution. | |
Section 13.02 | ______ | Not included in the regulation. Fees will be adopted by board resolution. | |
Section 13.03 | ______ | Not included in the regulation. Fees will be adopted by board resolution. | |
Section 13.04 | ______ | Not included in the regulation. Fees will be adopted by board resolution. | |
Section 13.05 | |||
13.05A | ______ | Not included in the regulation. Fees will be adopted by board resolution. | |
13.05B | ______ | Not included in the regulation. Fees will be adopted by board resolution. | |
13.05C | ______ | Not included in the regulation. Fees will be adopted by board resolution. | |
13.05D | 2.02D3 | ||
SIGNATURE PAGE | Page following the table of contents. |
(Reserved for later use)
Registration Program Information
A. The owner or operator of each source within the following
source categories, that does not hold an operating permit, shall
register the source with the Authority: (4.01A) This appendix
provides specific information on applicability and exemptions for
the registration program in section 4.01.
1. Agricultural drying and dehydrating operations;
2. Asphalt plants;
3. Beverage can surface coating operations;
4. Bulk gasoline terminals;
5. Cattle feed lots; for the purposes of registration a cattle feed lot is a place with facilities for 1,000 or more head of cattle which are kept closely confined for commercial purposes and substantially all feed used is delivered to them;
6. Chemical plants;
7. Ferrous foundries;
8. Fertilizer plants;
9. Flexible vinyl and urethane coating and printing operations;
10. Grain handling, seed processing, pea and lentil processing;
11. Metallic mineral processing plants;
12. Mineralogical processing plants;
13. Nonferrous foundries;
14. Other metallurgical processing plants;
15. Petroleum refineries;
16. Power boilers;
17. Pressure sensitive tape and label surface coating operations;
18. Rendering plants;
19. Scrap metal operations;
20. Synthetic organic chemical manufacturing industries;
21. Sulfuric acid plants;
22. Synthetic fiber production facilities;
23. Veneer dryers;
24. Wood waste incinerators including wigwam burners;
25. Other incinerators designed for a capacity of 100 lbs per hour or more;
26. Stationary internal combustion engines rated at 500 h.p. or more;
27. Sawmills, including processing for lumber, plywood, shake, shingle, pulp wood, insulating board, or any combination thereof.
28. Any category of stationary sources to which a New Source' Performance Standard (NSPS) applies. The categories as identified in the federal regulations 40 CFR Part 60 (January 1, 1993) are as follows:
Subpart D Fossil fuel fired steam generators for which construction commenced after August 17, 1971, and prior to September 19, 1978, which have a heat input greater than 73 megawatts but not greater than 250 megawatts
Subpart Da Electric utility steam generating units for which construction commenced after September 18, 1978, which have a heat input greater than 73 megawatts but not greater than 250 megawatts Subpart Db Industrial-commercial-institutional steam generating units for which construction commenced after June 19, 1984, and prior to June 19, 1986, which have a heat input greater than 29 megawatts but less than 73 megawatts
Subpart Dc Small industrial-commercial-institutional steam generating units
Subpart E Incinerators
Subpart Ea Municipal waste combustors
Subpart F Portland cement plants
Subpart G Nitric acid plants
Subpart H Sulfuric acid plants
Subpart I Asphalt concrete plants
Subpart J Petroleum refineries which produce less than 25,000 barrels per day of refined products
Subpart K Storage vessels for petroleum liquid constructed after June 11, 1973, and prior to May 19, 1978, which have a capacity greater than 40,000 gallons
Subpart Ka Storage vessels for petroleum liquids constructed after May 18, 1978, which have a capacity greater than 40,000 gallons
Subpart Kb Volatile organic liquid storage vessels (including petroleum liquid storage vessels) constructed, reconstructed, or modified after July 23, 1984
Subpart L Secondary lead smelters
Subpart M Brass and bronze ingot production plants
Subpart N Iron and steel plants
Subpart O Sewage treatment plants
Subpart P Primary copper smelters
Subpart Q Primary zinc smelters
Subpart R Primary lead smelters
Subpart S Primary aluminum reduction plants
Subpart T Phosphate fertilizer industry: Wet process phosphoric acid plants
Subpart U Phosphate fertilizer industry: Superphosphoric acid plants
Subpart V Phosphate fertilizer industry: Diammonium phosphate plants
Subpart W Phosphate fertilizer industry: Triple superphosphate plants
Subpart X Phosphate fertilizer industry: Granular triple superphosphate storage facilities
Subpart Y Coal preparation plants
Subpart Z Ferroalloy production facilities
Subpart AA Steel plants: Electric arc furnaces
Subpart AAa Steel plants: Electric arc furnaces and argon-oxygen decarburization vessels
Subpart BB Kraft pulp mills
Subpart CC Glass manufacturing plants
Subpart DD Grain elevators
Subpart EE Industrial surface coating: Metal furniture
Subpart GG Stationary gas turbines
Subpart HH Lime manufacturing plants
Subpart KK Lead-acid battery plants
Subpart LL Metallic mineral processing plants
Subpart MM Automobile and light duty truck surface coating operations
Subpart NN Phosphate rock plants
Subpart PP Ammonium sulfate manufacture
Subpart QQ Publication rotogravure printing
Subpart RR Pressure sensitive tape and label surface coating operations
Subpart SS Industrial surface coating: Large appliances
Subpart TT Industrial surface coating: Metal coils
Subpart UU Asphalt processing and asphalt roofing manufacture
Subpart VV SOCMI equipment leaks (VOC)
Subpart WW Beverage can surface coating operations
Subpart XX Bulk gasoline terminals
Subpart BBB Rubber tire manufacturing industry
Subpart DDD VOC emissions from the polymer manufacturing industry
Subpart FFF Flexible vinyl and urethane coating and printing
Subpart GGG Petroleum refineries - compressors and fugitive emission sources
Subpart HHH Synthetic fiber production facilities
Subpart III VOC emissions from SOCMI air oxidation unit processes
Subpart JJJ Petroleum dry cleaners
Subpart KKK Equipment leaks of VOC from onshore natural gas processing plants
Subpart LLL Onshore natural gas processing; SO2 emissions
Subpart NNN VOC emissions from SOCMI distillation operations
Subpart PPP Wool fiberglass insulation manufacturing plants
Subpart QQQ VOC emissions from petroleum refinery wastewater emissions
Subpart SSS Magnetic tape coating facilities
Subpart TTT Industrial surface coating: Surface coating of plastic parts for business machines
Subpart VVV Polymeric coating of supporting substrates facilities:
Note: For fossil fuel fired steam generators referenced by Subpart D and Da above, units greater than 250 megawatts are governed by the energy facility site.
29. Any source which emits a contaminant subject to a National Emission Standard for Hazardous Air Pollutants (NESHAPS);
30. Any major stationary source as defined below;
"Major source" means any stationary source (or any group of stationary sources) that are located on one or more contiguous or adjacent properties, and are under common control of the same person (or persons under common control) belonging to a single major industrial grouping and that are described in (a), (b), or (c) of this subsection. For the purposes of defining "major source," a stationary source or group of stationary sources shall be considered part of a single industrial grouping if all of the pollutant emitting activities at such source or group of sources on contiguous or adjacent properties belong to the same major group (i.e., all have the same two-digit code) as described in the Standard Industrial Classification Manual, 1987.
(a) A major source under section 112 of the FCAA, which is defined as any stationary source or group of stationary sources located within a contiguous area and under common control that emits or has the potential to emit, in the aggregate, ten tons per year (tpy) or more of any hazardous air pollutant which has been listed pursuant to section 112(b) of the FCAA, twenty-five tpy or more of any combination of such hazardous air pollutants, or such lesser quantity as the Administrator may establish by rule. Notwithstanding the preceding sentence, emissions from any oil or gas exploration or production well (with its associated equipment) and emissions from any pipeline compressor or pump station shall not be aggregated with emissions from other similar units, whether or not such units are in a contiguous area or under common control, to determine whether such units or stations are major sources; or
(b) A major stationary source of air pollutants, as defined in section 302 of the FCAA, that directly emits or has the potential to emit, one hundred tpy or more of any air pollutant (including any major source of fugitive emissions of any such pollutant, as determined by rule by the Administrator).
(c) A major stationary source as defined in part D of title I of the FCAA, including:
(i) For ozone nonattainment areas, sources with the potential to emit one hundred tpy or more of volatile organic compounds or oxides of nitrogen in areas classified as "marginal" or "moderate," fifty tpy or more in areas classified as "serious," twenty-five tpy or more in areas classified as "severe," and ten tpy or more in areas classified as "extreme"; except that the references in this paragraph to one hundred, fifty, twenty-five, and ten tpy of nitrogen oxides shall not apply with respect to any source for which the Administrator has made a finding, under section 182 (f)(1) or (2) of the FCAA, that requirements under section 182(f) of the FCAA do not apply;
(ii) For ozone transport regions established pursuant to section 184 of the FCAA, sources with the potential to emit fifty tpy or more of volatile organic compounds;
(iii) For carbon monoxide nonattainment areas (A) that are classified as "serious," and (B) in which stationary sources contribute significantly to carbon monoxide levels, sources with the potential to emit fifty tpy or more of carbon monoxide; and
(iv) For particulate matter (PM-10) nonattainment areas classified as "serious," sources with the potential to emit seventy tpy or more of PM-10.
31. Any of the following categories of sources which are listed in WAC 173-460-030(1):
Standard industrial classifications:
Major group 10-Metal mining.
Major group 12-Bituminous coal and lignite mining.
Major group 13-Oil and gas extraction.
Manufacturing industries major groups 20-39.
Major group 49-Electric, gas, and sanitary services except 4971 irrigation systems.
Dry cleaning plants, 7216.
General medical surgical hospitals, 8062.
Specialty hospitals, 8069.
National Security, 9711.
Any Source category listed in WAC 173-490-030(1) except WAC 173-490-030 (1)(e) Gasoline dispensing facilities.
WAC 173-490-030(1) categories:
a. Petroleum refineries.
b. Petroleum liquid storage tanks.
c. Gasoline loading terminals.
d. Bulk gasoline plants.
f. Surface coaters.
g. Open top vapor degreasers.
h. Conveyerized degreasers.
i. Gasoline tansport tanks.
j. Vapor collection systems.
k. Perchloroethlene dry cleaning systems.
l. Graphic arts systems.
m. Surface coaters of miscellaneous metal parts and products.
n. Synthesized pharmaceutical manufacturing facilities.
o. Flatwood panel manufacturers and surface finishing facilities.
Any of the following sources:
Landfills.
Sites subject to chapter 173-340 WAC Model Toxics Control Act--Cleanup regulation.
A. SOURCE CLASSIFICATION LIST. (WAC 173-400-100(1))
1. Agricultural chemical facilities engaging in the manufacturing of liquid or dry fertilizers or pesticides;
2. Agricultural drying and dehydrating operations;
3. Any category of stationary sources to which a federal standard of performance (NSPS) under 40 CFR Part 60 (App. B) as of the effective date in section 1.08, other than Subpart AAA (Standards of Performance for New Residential Wood Heaters) applies;
4. Any source category subject to a National Emission Standard for Hazardous Air Pollutants (NESHAPS) under 40 CFR Part 61 as of the effective date in section 1.08, other than Subpart M (National Emission Standard for Asbestos) or a Maximum Achievable Control Technology (MACT) standard in 40 CFR Part 63 as of the effective date in section 1.08 established under Section 112 of the FCAA (App. B);
5. Any source, stationary source or emission unit with a significant emission as defined by WAC 173-400-030(67);
6. Asphalt and asphalt products production facilities;
7. Brick and clay manufacturing plants, including tiles and ceramics;
8. Casting facilities and foundries, ferrous and nonferrous;
9. Cattle feedlots with facilities which operate between June 1st and October 1st, have an inventory of 1,000 or more cattle, and vegetation forage growth is not sustained over the majority of the lot during the normal growing season;
10. Chemical manufacturing plants;
11. Composting operations, including commercial, industrial and municipal, but exempting residential composting activities;
12. Concrete product manufacturers and ready mix and premix concrete plants;
13. Crematoria or animal carcass incinerators;
14. Dry cleaning plants;
15. Materials handling and transfer facilities that generate fine particulate, which may include pneumatic conveying, cyclones, baghouses, and industrial housekeeping vacuuming systems that exhaust to the atmosphere;
16. Flexible vinyl and urethane coating and printing operations;
17. Grain, seed, animal feed, legume, and flour processing operations, and handling facilities;
18. Hay cubers and pelletizers;
19. Hazardous waste treatment and disposal facilities;
20. Ink manufacturers;
21. Insulation fiber manufacturers;
22. Landfills, active and inactive, including covers, gas collection systems or flares;
23. Metal plating and anodizing operations;
24. Metallic and nonmetallic mineral processing plants, including rock crushing plants;
25. Mills such as lumber, plywood, shake, shingle, wood chip, veneer operations, dry kilns, pulpwood insulating board, or any combination thereof;
26. Mineralogical processing plants;
27. Other metallurgical processing plants;
28. Paper manufacturers;
29. Petroleum refineries;
30. Plastics and fiberglass product fabrication facilities;
31. Rendering plants;
32. Soil and groundwater remediation projects;
33. Surface coating manufacturers;
34. Surface coating operations including: Automotive, metal, cans, pressure sensitive tape, labels, coils, wood, plastic, rubber, glass, paper and other substrates;
35. Synthetic fiber production facilities;
36. Synthetic organic chemical manufacturing industries;
37. Tire recapping facilities;
38. Wastewater treatment plants;
39. Any source that has elected to opt-out of the operating permit program by limiting its potential-to-emit (synthetic minor) or is required to report periodically to demonstrate nonapplicability to EPA requirements under Sections 111 or 112 of FCAA.
B. Equipment Classification List. (WAC 173-400-100(2))
1. Boilers, all solid and liquid fuel burning boilers with the exception of those used for residential heating;
2. Boilers, all gas fired boilers above 10 million Btu (App. B) per hour input;
3. Chemical concentration evaporators;
4. Degreasers of the cold or vapor type in which more than 5% of the solvent is comprised of halogens or such aromatic hydrocarbons as benzene, ethylbenzene, toluene or xylene;
5. Ethylene oxide (ETO) sterilizers;
6. Flares utilized to combust any gaseous material;
7. Fuel burning equipment with a heat input of more than 1,000,000 Btu per hour; except heating, air conditioning systems, or ventilating systems not designed to remove contaminants generated by or released from equipment;
8. Incinerators designed for a capacity of 100 pounds per hour or more;
9. Ovens, burn-out and heat-treat;
10. Stationary internal combustion engines and turbines rated at 500 horsepower or more;
11. Storage tanks for organic liquids associated with commercial or industrial facilities with capacities equal to or greater than 40,000 gallons;
12. Vapor collection systems within commercial or industrial facilities;
13. Waste oil burners above 0.5 mm Btu heat output;
14. Woodwaste incinerators.
Legal Land Descriptions
This appendix provides the legal land descriptions for geographic areas cited in the regulation (App. A).
A. WOODSMOKE CONTROL ZONE - An area located in Yakima County, Washington, as shown in Attachment 1, which is legally described as follows:
Beginning at a point on a line which is herein called the Western boundary, and which line is a straight line drawn through the following points:
Point A - Where the South right-of-way line of Highway 410 intersects with the North right-of-way line of Highway 12.
Point B - Where the South right-of-way line of the North Fork of Ahtanum Road intersects with the North right-of-way line of the South Fork of Ahtanum Road.
Which line further extends in a Southwesterly direction to a
point where it intersects with the South boundary line of
Sections 19, 20, 21, 22, 23, 24 or Township 12 N., Range 16 E.,
W.M. as such boundary line is extended both Easterly and
Westerly, and thence Easterly along said South boundary line of
said Sections as extended to the Southeast corner of Section 19,
Township 12 N., Range 18 E., W.M.; thence North along the East
boundary line of said section to the Northeast corner thereof;
thence East along the North boundary line of Sections 20, 21, 22,
23, 24, of Township 12 N., Range 18 E., W.M. as extended Easterly
to the Northeast corner of Section 21, Township 12 N., Range 20
E., W.M.; thence North along the East boundary line of Sections
16, 9 and 4 of Township 12 N., Range 20 E., W.M.: thence East to
the Southeast corner of Section 34, Township 13 N, Range 20 E.,
W.M.; thence North along the Easterly boundary line of said
Section to the intersection with the U.S. Military Reservation,
Yakima Firing Training Center; thence Northerly and Westerly
along the boundary line of the U.S. Military Reservation to the
Southern boundary of Kittitas County; thence West to the
Southeast corner of Section 36, Township 15 N., Range 18 E.,
W.M.; thence North to the Northeast corner of Section 24,
Township 15 N., Range 18 E., W.M.; thence West to the Southeast
corner of Section 18, Township 15 N, Range 18 E. W.M. thence West
to the intersection of the West boundary line as herein
described; thence Southwesterly along said West boundary line to
the point of beginning.
B. YAKIMA URBAN AREA - An area located in Yakima County,
Washington, as shown in Attachment 2, which is legally described
(Yakima City Code-Title 15A, Ord.# 10-1985) as follows:
Beginning at the southwest corner of Government Lot 5, Section 17, Township 12 N., Range 19 E., W.M.; thence north along the west line of said Section 17 to the southeast corner of Section 7. Township 12 N., Range 19 E., W.M., thence west along the south line of said Section 7 to the southwest corner of the southeast quarter of said Section 7; thence north along the west line of the east half of said Section 7 to Ahtanum Creek, thence following Ahtanum Creek in a generally westerly direction to the west line of the southwest quarter of the south-east quarter of Section 2, Township 12 N., Range 18 E., W.M.; thence north along said west line to the northwest corner of the southwest quarter of the southeast quarter of said Section 2; thence west along the east-west centerline of the south half of said Section 2 to the west line of said Section 2; thence continuing west along the east-west centerline of the south half of Section 3, Township 12 N., Range 18 E., W.M. to South 34th Avenue; thence north along South 34th Avenue to Ahtanum Road - thence west along Ahtanum Road to 38th Avenue; thence north along 38th Avenue to the north line of Section 3. Township 12 N., Range 18 E., W.M.; thence west along said north line to the northeast corner of Section 4, Township 12 N, Range 18 E., W.M.; thence continuing west along the north line of said Section 4 to the southeast corner of Section 33, Township 13 N., Range 18 E., W.M.; thence continuing west along the south line of said Section 33 to 64th Avenue; thence north along 64th Avenue to the east-west centerline of Sections 32 and 33, Township 13 N, Range 18 E., W.M.; thence west along said east-west centerline to the north-south centerline of the west half of said Section 32; thence north along said north-south centerline to Zier Road; thence west along Zier Road to South 80th Avenue; thence north along South 80th Avenue to Wide Hollow Road; thence west along Wide Hollow Road to the north-south centerline of the east half of Section 30, Township 13 North, Range 18 East W.M.; thence north along said north-south centerline to the east-west centerline of said Section 30; thence west along said east-west centerline to the north-south centerline of the west half of said Section 30; thence north along said north-south centerline to the Yakima Valley Canal; thence following the Yakima Valley Canal in a generally westerly direction to its intersection with Tieton Drive; thence west on Tieton Drive to 96th Avenue; thence north on 96th Avenue to the northwest corner of the southwest quarter of Section 19, Township 13 N., Range 18 E., W.M.; thence north along the west section line of said Section 19 to a point 250 feet south of the northwest corner of the southwest quarter of the northwest quarter of said Section 19; thence north 89°33' East to the Tieton Canal; thence following the Tieton Canal in a generally northeasterly direction to the north-south centerline of the east half of said Section 19; thence north along said north-south centerline to the north-south centerline of the east half of Section 18, Township 13 N., Range 18 E., W.M.; thence north along said north-south centerline of said Section 18 to the east-west centerline of the south half of said Section 18; thence east along said east-west centerline to the west line of Section 17, Township 13 N., Range 18 E., W.M.; thence north along said west line to the east-west centerline of said Section 17; thence east along said east-west centerline to the east line of said Section 17; thence north along said east line to the south right-of-way line of the former Burlington Northern Railroad, Cowiche Branch; thence following said south right-of-way line in a generally northeasterly direction to the north right-of-way line of State Route 12; thence following said north right-of-way line in a generally southeasterly direction to Cowiche Creek; thence following Cowiche Creek in a generally northeasterly direction to its confluence with the Naches River; thence following the south bank of the Naches River and the south bank of the Yakima River in a generally easterly direction to the north-south centerline of the east half of Section 12, Township 13 N., Range 18 E., W.M.; thence north along said north-south centerline to Rest Haven Road; thence following Rest Haven Road in a generally southeasterly direction to the south line of Section 8, Township 13 N., Range 19 E., W.M.; thence east along the south line of Sections 8 and 9 to the southwest corner of Lot 3 of that certain short plat recorded in Volume 81, Page 133, Short Plat Records of Yakima County; thence continuing east 260 feet along said south section line; thence North 0°022'34" east 270.51 feet; thence north 38°30'50" east 146.66 feet; thence north 47°30'24" east 63.80 feet; thence north 77°58'20" east 1,026.46 feet; thence north 71°00' east 255.38 feet; thence north 59°00' east to the north line of the southwest quarter the southwest quarter of Section 10, Township 13 N., Range 19 E., W.M., thence easterly along said north line to the Northeast corner of said subdivision; thence southerly along the east line of the south-west quarter of the southwest quarter of said Section 10 to the south-east corner of said subdivision; thence westerly along the south line of said Section 10 to the northwest corner of Section 15, Township 13 N., Range 19 E., W.M., thence southerly along the west line of said Section 15 to the southwest corner of the northwest quarter of said Section 15; thence easterly along said east-west centerline to the southeast corner of the northeast quarter of said Section 15; thence easterly along the east-west centerline of Section 14, Township 13 N, Range 19 E., W.M. to the northeast corner of the northwest quarter of the southwest quarter of said Section 14; thence southerly along the north-south centerline of the west half of said Section 14 to the southeast corner of the southwest quarter of the southwest quarter of said Section 14; thence easterly along the south line of said Section 14 to the northeast corner of Section 23, Township 13 N., Range 19 E., W.M.; thence southerly along the east line of said Section 23 to the southeast corner of said Section 23; thence westerly along the south lines of Sections 23, 22, 21 and 20, Township 13 N., Range 19 E., W.M. to the west bank of the Yakima River; thence following said west bank in a generally southerly direction to a point where it intersects the east right-of-way line of Interstate Highway 82; thence westerly to the point where the west right-of-way line of said interstate highway intersects the south line of Government Lot 2 of Section 17, Township 12 N., Range 19 E., W.M.; thence westerly along the south line of said Government Lot 2 and of Government Lot 5 of said Section 17 to the south-west corner of said Government Lot 5 and the point of beginning.
C. YAKIMA CO NONATTAINMENT AREA. (40 CFR 81.348)
The boundaries and UTM (App. B) coordinates are described as the following:
UTMW | UTMN | Street - Intersection |
689.06 | 5160.91 | S 16th Ave/W Mead Ave |
688.92 | 5165.05 | S 16th Ave/Hthwy Ave |
690.35 | 5465.10 | E "I" St/N 1st St |
690.49 | 5164.63 | N 1st St/E "G" St |
691.31 | 5165.01 | E "G" St N N 8th St |
691.70 | 5164.07 | N 8th St/Pitcher St |
692.42 | 5164.09 | Pitcher St/I-82 Intrchge |
693.18 | 5162.80 | Nob Hill Blvd Intrchge |
693.58 | 5161.61 | Nob Hill Blvd Intrchge |
693.66 | 5159.57 | Rudkin Road Intrchge |
693.06 | 5159.55 | S 1st Old Town Rd/Mn St |
692.43 | 5160.32 | W Washington/S 1st St |
682.05 | 5161.07 | E Mead Ave/S 1st St |
689.06 | 5160.91 | S 16th Ave/W Mead Ave |
The corners and UTM coordinates are:
Corner | UTMW | UTMN |
Southeast | 694.00 | 5157.00 |
Southwest | 681.00 | 5157.00 |
Northwest | 681.00 | 5172.00 |
Northeast | 694.00 | 5172.00 |
Maps
Name | Page Number |
|
Woodsmoke Control Zone | I-2 | |
Yakima Urban Area | I-3 | |
Yakima CO Nonattainment Area | I-4 | |
Yakima PM10 Nonattainment Area | I-5 |
Place illustration here. |
Place illustration here. |
Place illustration here. |
Place illustration here. |
ERC Discounting Factors
(Reserved for later use)
New Source Review Application Information
This appendix provides specific information on exemptions for NSR (App. B) applications under section 4.02.
A. EMISSION UNIT AND ACTIVITY EXEMPTIONS FOR NON-TOXIC AIR POLLUTANTS. (WAC 173-400-110(4)
1. Maintenance/Construction.
a. Cleaning and sweeping of streets and paved surfaces;
b. Concrete application, and installation;
c. Dredging wet spoils handling and placement;
d. Paving application and maintenance, excluding asphalt plants;
e. Plant maintenance and upkeep activities including ground keeping, general repairs, routine house keeping, routine plant painting, welding, cutting, brazing, soldering, plumbing, retarring roofs, etc.;
f. Plumbing installation, plumbing protective coating application and maintenance activities;
g. Roofing application;
h. Insulation application and maintenance, excluding products for resale;
i. Janitorial services and consumer use of janitorial products.
2. Storage Tanks.
a. Lubricating oil storage tanks except those facilities that are wholesale or retail distributors of lubricating oils;
b. Polymer tanks and storage devices and associated pumping and handling equipment, used for solids dewatering and flocculation;
c. Storage tanks, reservoirs, pumping and handling equipment of any size containing soaps, vegetable oil, grease, animal fat, and nonvolatile aqueous salt solutions;
d. Process and white water storage tanks;
e. Operation, loading and unloading of storage tanks, and storage vessels, with lids or other appropriate closures and less than 260 gallon capacity (35 cf);
f. Operation, loading and unloading of storage tanks, ≤ 1,100 gallon capacity, with lids or other appropriate closure, not for use with materials containing TAP (App. B), as defined in 173-460 WAC, max. VP 550 mm Hg @ 21°C (App. B);
g. Operation, loading and unloading storage of butane, propane, or LP gas (App. B) with a vessel capacity < 40,000 gallons;
h. Tanks, vessels and pumping equipment, with lids or other appropriate closure for storage or dispensing of aqueous solutions of inorganic salts, bases and acids.
3. Projects with Combined Aggregate Heat Inputs of Combustion Units, ≤ all of the Following:
a. ≤500,000 Btu/hr (App. B) using coal with ≤ 0.5% sulfur or other fuels with ≤ 0.5% sulfur;
b. ≤500,000 Btu/hr used oil, per the requirements of RCW 70.94.610;
c. ≤400,000 Btu/hr wood waste or paper;
d. <1,000,000 Btu/hr using kerosene, #1 or #2 fuel oil and with ≤0.05% sulfur.
e. ≤4,000,000 Btu/hr using natural gas, propane, or LP gas.
4. Material Handling:
a. Continuous digester chip feeders;
b. Grain elevators not licensed as warehouses or dealers by either the DOA (App. B) or USDA (App. B);
c. Storage and handling of water based lubricants for metal working where organic content of the lubricant is ≤ 10%;
d. Equipment used exclusively to pump, load, unload, or store high boiling point organic material in tanks less than 1,000,000 gallon, material with initial atmospheric boiling point not less than 150°C or vapor pressure not more than 5 mm Hg @21°C, with lids or other appropriate closure.
5. Water Treatment:
a. Septic sewer systems, not including active wastewater treatment facilities;
b. NPDES (App. B) permitted ponds and lagoons used solely for the purpose of settling suspended solids and skimming of oil and grease;
c. De-aeration (O2 scavenging) of water where toxic air pollutants as defined in chap. 173-460 WAC are not emitted;
d. Process water filtration system and demineralize vents;
e. Sewer manholes, junction boxes, sumps, and lift stations associated with wastewater treatment systems;
f. Demineralize tanks;
g. Alum tanks;
h. Clean water condensate tanks.
6. Environmental Chambers and Laboratory Equipment:
a. Environmental chambers and humidity chambers not using toxic air pollutant gases, as regulated under 173-460 WAC;
b. Gas cabinets using only gases that are not toxic air pollutants regulated under 173-460 WAC;
c. Installation or modification of a single laboratory fume hood;
d. Laboratory calibration and maintenance equipment.
7. Monitoring/Quality Assurance/Testing:
a. Equipment and instrumentation used for quality control/assurance or inspection purpose;
b. Hydraulic and hydrostatic testing equipment;
c. Sample gathering, preparation, and management;
d. Vents from continuous emission monitors and other analyzers.
8. Miscellaneous:
a. Single-family residences and duplexes;
b. Plastic pipe welding;
c. Primary agricultural production activities including soil preparation, planting, fertilizing, week and pest control, and harvesting;
d. Comfort air conditioning;
e. Flares used to indicate danger to public;
f. Natural and forced air vents and stacks for bathroom/toilet activities;
g. Personal care activities;
h. Recreational fireplaces used for barbecues, campfires, or ceremonial fires;
I. Tobacco smoking rooms and areas;
j. Noncommercial smokehouses;
k. Blacksmith forges for single forges;
l. Vehicle maintenance activities, not including vehicle surface coating;
m. Vehicle or equipment washing;
n. Wax application;
o. Oxygen, nitrogen, or rare gas extraction and liquefaction equipment not including internal and external combustion equipment;
p. Ozone generators and ozonation equipment;
q. Solar simulators;
r. Ultraviolet curing processes, to the extent that toxic air pollutant gases as defined in 173-460 WAC are not emitted;
s. Electric circuit breakers, transformers, or switching equipment installation or operation;
t. Pulse capacitors;
u. Pneumatically operated equipment, including tools and hand held applicator equipment for hot melt adhesives;
v. Recovery boiler blow-down tank;
w. Screw press vents;
x. Drop hammers or hydraulic presses for forging or metal working;
y. Production of foundry sand molds, unheated and using binders less than 0.25% free phenol by sand weight;
z. Kraft lime mud storage tanks and process vessels;
aa. Lime grits washers, filters and handling;
bb. Lime mud filtrate tanks;
cc. Lime mud water;
dd. Stock cleaning and pressurized pulp washing down process of the brown stock washer;
ee. Natural gas pressure regulator vents, excluding venting at oil and gas production facilities and transportation marketing facilities;
ff. Nontoxic air pollutant, as defined in 173-460 WAC, solvent cleaners less than 10 sf (App. B) air-vapor interface with solvent vapor pressure not more than 30 mm Hg @21°C;
gg. Surface coating, aqueous solution or suspension containing ≤ 1% (by weight) VOCs (App. B), and/or toxic air pollutants as defined in 173-460 WAC;
hh. Cleaning and stripping activities and equipment using solutions having ≤ 1% VOCs (by weight); on metallic substances, acid solutions are not exempt;
ii. Dip coating operations, using materials less than 1% VOCs (by weight) and/or toxic air pollutants as defined in 173-460 WAC.
B. TOXIC AIR POLLUTANTS.
1. Class A TAP. (WAC 173-460--150)
a. Table K-1, Class A TAP, Known, Probable, and Potential Human Carcinogens.
Chemical Abstract Service Number |
Substance |
75-07-0 | Acetaldehyde |
53-96-3 | 2-Acetylaminofluorene |
79-06-1 | Acrylamide |
107-13-1 | Acrylonitrile |
309-00-2 | Aldrin |
SSS | Aluminum smelter polyaromatic hydrocarbon emissions |
117-79-3 | 2-Aminoanthraquinone |
97-56-3 | o-Aminoazotoluene |
92-67-1 | 4-Aminobiphenyl |
61-82-5 | Amitrole |
62-53-3 | Aniline |
90-04-0 | o-Anisidine |
C7440-38-2 | Arsenic and inorganic arsenic compounds |
1332-21-4 | Asbestos |
2465-27-2 | Auramine (technical grade) |
71-43-2 | Benzene |
92-87-5 | Benzidine and its salts |
56-55-3 | Benzo(a)anthracene |
50-32-8 | Benzo(a)pyrene |
205-99-2 | Benzo(b)fluoranthene |
205-82-3 | Benzo(j)fluoranthene |
207-08-9 | Benzo(k)fluoranthene |
1694-09-3 | Benzyl violet 4b |
7440-41-7 | Beryllium and compounds |
111-44-4 | Bis(2-chloroethyl)ether |
117-81-7 | Bis(2-ethylhexyl)phthalate (DEHP) |
542-88-1 | Bis(chloromethyl)ether |
75-25-2 | Bromoform |
106-99-0 | 1,3-Butadiene |
3068-88-0 | B-Butyrolactone |
7440-43-9 | Cadmium and compounds |
56-23-5 | Carbon tetrachloride |
57-74-9 | Chlordane |
510-15-6 | Chlorobenzilate |
67-66-3 | Chloroform |
107-30-2 | Chloromethyl methyl ether (technical-grade) |
108-43-0 | Chlorophenols |
126-99-8 | Chloroprene |
C7440-47-3 | Chromium, hexavalent metal and compounds |
SSS | Coke oven emissions |
8001-58-9 | Creosote |
135-20-6 | Cupferron |
94-75-7 | 2,4-D and esters |
3547-04-4 | DDE (p,p'-Dichlorodiphenyldichloroethylene) |
50-29-3 | DDT (1,1,1 Trichloro-2,2-Bis(p-chlorophenyl)-ethane) |
613-35-4 | N,N-Diacetylbenzidine |
101-80-4 | 4,4'-Diaminodiphenyl ether |
226-36-8 | Dibenz(a,h)acridine |
53-70-3 | Dibenz(a,h)anthracene |
224-42-0 | Dibenz(a,j)acridine |
132-64-9 | Dibenzofurans |
189-64-0 | Dibenzo(a,h)pyrene |
191-30-0 | Dibenzo(a,l)pyrene |
189-55-9 | 1,2,7,8-Dibenzopyrene (dibenzo(a,i)pyrene) |
192-65-4 | Dibenzo(a,e)pyrene |
764-41-0 | 1,4-Dichloro-2-butene |
28434-86-8 | 3,3'-Dichloro-4,4'-diaminodiphenyl ether |
106-46-7 | 1,4-Dichlorobenzene |
91-94-1 | 3, 3'-Dichlorobenzidine |
107-06-2 | 1,2-Dichloroethane (ethylene chloride) |
75-09-2 | Dichloromethane (methylene chloride) |
696-28-6 | Dichlorophenylarsine (arsenic group) |
78-87-5 | 1,2-Dichloropropane |
60-57-1 | Dieldrin |
1615-80-1 | 1,2-Diethylhydrazine |
101-90-6 | Diglycidyl resorcinol ether |
119-90-4 | 3.3'-Dimethoxybenzidine (ortol-dianisidine) |
119-93-7 | 3,3-Dimethyl benzidine |
77-78-1 | Dimethyl sulfate |
540-73-8 | 1,2-Dimethylhydrazine |
123-91-1 | 1,4-Dioxane |
SSS | Dioxins and furans |
122-66-7 | 1,2-Diphenylhydrazine |
106-89-8 | Epichlorohydrin |
106-93-4 | Ethylene dibromide (dibromethane) |
75-21-8 | Ethylene oxide |
96-45-7 | Ethylene thiourea |
50-00-0 | Formaldehyde |
67-45-8 | Furazolidone |
Furium (nitrofuran group) | |
765-34-4 | Glyciadaldehyde |
76-44-8 | Heptachlor |
118-74-1 | Hexachlorobenzene |
319-84-6 | Hexachlorocyclohexane (Lindane) Alpha BHC |
319-85-7 | Hexachlorocyclohexane (Lindane) Beta BHC |
58-89-9 | Hexachlorocyclohexane (Lindane) Gamma BHC |
680-31-9 | Hexamethylphosphoramide |
302-01-2 | Hydrazine |
193-39-5 | Indeno(1,2,3-cd)pyrene |
SSS | Isopropyl oils |
SSS | Lead compounds |
301-04-2 | Lead acetate |
7446-27-7 | Lead phosphate |
129-15-7 | 2-Methyl-1-nitroanthraquinone |
592-62-1 | Methyl azoxymethyl acetate |
3697-24-3 | 5-Methylchrysene |
101-14-4 | 4,4'-Methylenebis(2-chloroaniline) (MBOCA) |
838-88-0 | 4,4'-Methylenebis(2-methylaniline) |
101-77-9 | 4,4-Methylene dianiline |
13552-44-8 | 4,4-Methylenedianiline dihydrochloride |
64091-91-4 | 4-(Methylnitrosamino)-1-(3-pyridyl)-1-butanone |
2385-85-5 | Mirex |
139-91-3 | 5-(Morpholinomethyl)-3-amino)- |
2-oxazolidinone (furaltudone) | |
134-32-7 | 1-Napthylamine |
C7440-02-0 | Nickel and compounds (as nickel subsulfide or nickel refinery dust) |
531-82-8 | N-(4-(5-Nitro-2-furyl)-2-thiazolyl)acetamide |
602-87-9 | 5-Nitroacenaphthene |
1836-75-5 | Nitrofen |
Nitrofurans | |
59-87-0 | Nitrofurazone |
555-84-9 | 1-(5-Nitrofurfurylidene)amino)-2-imidazolidinone |
126-85-2 | Nitrogen mustard N-oxide |
302-70-5 | Nitrogen mustard N-oxide hydrochloride |
79-46-9 | 2-Nitropropane |
924-16-3 | N-Nitrosodi-n-butylamine |
759-73-9 | N-Nitroso-N-ethylurea (NEU) |
615-53-2 | N-Nitroso-N-methylurethane |
621-64-1 | N-Nitrosodi-n-propylamine |
10595-95-6 | N-Nitrosomethylethylamine |
59-89-2 | N-Nitrosomorpholine |
86-30-6 | N-Nitrosodiphenylamine |
55-18-5 | N-Nitrosodiethylamine (diethylnitrosoamine) (DEN) |
62-75-9 | N-Nitrosodimethylamine |
2646-17-5 | Oil orange SS |
794-93-4 | Panfuran S (dihydroxymethylfuratrizine) |
87-86-5 | Pentachlorophenol |
127-18-4 | Perchloroethylene (tetrachloroethylene) |
63-92-3 | Phenoxybenzamine hydrochloride |
N-Phenyl-2-napthylamine | |
SSS | Polyaromatic hydrocarbons (PAH) |
1336-36-3 | Polychlorinated biphenyls (PCBs) |
3761-53-3 | Ponceau MX |
P(p)(alpha, alpha, alpha)-Tetra-chlorotoluene | |
SSS | Primary aluminum smelter |
1120-71-4 | 1,3-Propane sultone |
75-56-9 | Propylene oxide |
1746-01-6 | 2,3,7,8-Tetrachlorodibenzo-p-dioxin (2,3,7,8-TCDD) |
139-65-1 | 4,4'-Thiodianiline |
1314-20-1 | Thorium dioxide |
95-80-7 | 2,4-Toluene diamine |
584-84-9 | 2,4-Toluene diisocyanate |
95-53-4 | o-Toluidine |
636-21-5 | o-Toluidine hydrochloride |
8001-35-2 | Toxaphene |
55738-54-0 | Trans-2((Dimethylamino)methylimino)-5- |
(2-(5-nitro-2-furyl) vinyl-1,3,4-oxadiazole | |
79-01-6 | Trichloroethylene |
88-06-2 | 2,4,6-Trichlorophenol |
75-01-4 | Vinyl chloride |
Chemical Abstract Service Number |
Substance | 10-6 Risk ASIL µg/m3 Annual Average |
75-07-0 | Acetaldehyde | 0.4500000 |
79-06-1 | Acrylamide | 0.0007700 |
107-13-1 | Acrylonitrile | 0.0150000 |
309-00-2 | Aldrin | 0.0002000 |
62-53-3 | Aniline | 6.3000000 |
C7440-38-2 | Arsenic and inorganic arsenic compounds | 0.0002300 |
1332-21-4 | Asbestos in fibers/ml | 0.0000044 |
71-43-2 | Benzene | 0.1200000 |
92-87-5 | Benzidine and its salts | 0.0000150 |
50-32-8 | Benzo(a)pyrene | 0.0004800 |
7440-41-7 | Beryllium and compounds | 0.0004200 |
111-44-4 | Bis(2-chloroethyl)ether | 0.0030000 |
117-81-7 | Bis(2-ethylhexyl)phthalate (DEHP) | 2.5000000 |
542-88-1 | Bis(chloromethyl)ether | 0.0000160 |
75-25-2 | Bromoform | 0.9100000 |
106-99-0 | 1,3-Butadiene | 0.0036000 |
7440-43-9 | Cadmium and compounds | 0.0005600 |
57-74-9 | Chlordane | 0.0027000 |
510-15-6 | Chlorobenzilate | 0.2000000 |
67-66-3 | Chloroform | 0.0430000 |
108-43-0 | Chlorophenols | 0.1800000 |
C7440-47-3 | Chromium, hexavalent metal and compounds | 0.0000830 |
------ | Coke oven emissions | 0.0016000 |
3547-04-4 | DDE (p,p'-Dichlorodiphenyldichloroethylene) | 0.1000000 |
50-29-3 | DDT (1,1,1 Trichloro-2,2-Bis(p-chlorophenyl)-ethane) | 0.0100000 |
764-41-0 | 1,4-Dichloro-2-butene | 0.0003800 |
106-46-7 | 1,4-Dichlorobenzene | 1.5000000 |
91-94-1 | 3, 3'-Dichlorobenzidine | 0.0770000 |
107-06-2 | 1,2-Dichloroethane (ethylene chloride) | 0.0380000 |
75-09-2 | Dichloromethane (methylene chloride) | 0.5600000 |
60-57-1 | Dieldrin | 0.0002200 |
119-93-7 | 3,3-Dimethyl benzidine | 0.0038000 |
123-91-1 | 1,4-Dioxane | 0.0320000 |
122-66-7 | 1,2-Diphenylhydrazine | 0.0045000 |
106-89-8 | Epichlorohydrin | 0.8300000 |
106-93-4 | Ethylene dibromide (dibromethane) | 0.0045000 |
75-21-8 | Ethylene oxide | 0.0100000 |
96-45-7 | Ethylene thiourea | 1.0000000 |
50-00-0 | Formaldehyde | 0.077000 |
76-44-8 | Heptachlor | 0.0007700 |
118-74-1 | Hexachlorobenzene | 0.0022000 |
58-89-9 | Hexachlorocyclohexane (Lindane) Gamma BHC | 0.0026000 |
302-01-2 | Hydrazine | 0.0002000 |
C7440-02-0 | Nickel and compounds (as nickel subsulfide or nickel refinery dust) | 0.0021000 |
924-16-3 | N-Nitrosodi-n-butylamine | 0.0006300 |
55-18-5 | N-Nitrosodiethylamine (diethylnitrosoamine) (DEN) | 0.0000230 |
62-75-9 | N-Nitrosodimethylamine | 0.0000710 |
79-46-9 | 2-Nitropropane | 0.0003700 |
87-86-5 | Pentachlorophenol | 0.3300000 |
127-18-4 | Perchloroethylene (tetrachloroethylene) | 1.1000000 |
1336-36-3 | Polychlorinated biphenyls (PCBs) | 0.0045000 |
75-56-9 | Propylene oxide | 0.2700000 |
1746-01-6 | 2,3,7,8-Tetrachlorodibenzo-p-dioxin (2,3,7,8-TCDD) | 0.00000003 |
95-80-7 | 2,4-Toluene diamine | 0.0110000 |
95-53-4 | o-Toluidine | 0.1400000 |
636-21-5 | o-Toluidine hydrochloride | 0.1400000 |
8001-35-2 | Toxaphene | 0.0031000 |
79-01-6 | Trichloroethylene | 0.5900000 |
88-06-2 | 2,4,6-Trichlorophenol | 0.3200000 |
75-01-4 | Vinyl chloride | 0.0120000 |
Chemical Abstract Service Number |
Substance | ASIL µg/m3 |
Averaging Time |
----- | Primary aluminum smelter uncontrolled roof vent polyaromatic hydrocarbon (PAH) emissions 1/ | 0.0013 | Annual |
61-82-5 | Amitrole | 0.06 | 24 hr. |
90-04-0 | o-Anisidine | 1.7 | 24 hr. |
126-99-8 | &bgr;-Chloroprene | 120 | 24 hr. |
94-75-7 | 2,4-D and esters | 33 | 24 hr. |
78-87-5 | 1,2-Dichloropropane | 4.0 | 24 hr. |
77-78-1 | Dimethyl sulfate | 1.7 | 24 hr. |
540-73-8 | 1,2-Dimethylhydrazine | 4.0 | 24 hr. |
319-84-6 | Hexachlorocyclohexane (Lindane) Alpha BHC | 1.7 | 24 hr. |
319-85-7 | Hexachlorocyclohexane (Lindane) Beta BHC | 1.7 | 24 hr. |
----- | Lead compounds | 0.5 | 24 hr. |
101-14-4 | 4,4'-Methylenebis(2-chloroaniline) (MBOCA) | 0.7 | 24 hr. |
------ | Polyaromatic hydrocarbon (PAH) emissions 1/ | 0.00048 | Annual |
584-84-9 | 2,4-Toluene diisocyanate | 0.12 | 24 hr. |
1/ See WAC 173-460-050 (4)(d)(i & ii) for the quantification procedure.
2. Table K-4, Class B TAP. Any Substance that is not a
Simple Asphyxiant or Nuisance Particulate. (WAC 173-460-160)
Chemical Abstract Service Number |
Substance | ASIL µg/m3 24 Hr. Average |
86-88-4 | ANTU | 1.0 |
60-35-5 | Acetamide | ----- |
64-19-7 | Acetic acid | 83 |
108-24-7 | Acetic anhydride | 67 |
67-64-1 | Acetone | 5900 |
75-05-8 | Acetonitrile | 220 |
98-86-2 | Acetophenone | ----- |
79-27-6 | Acetylene tetrabromide | 47 |
107-02-8 | Acrolein | 0.02 |
79-10-7 | Acrylic acid | 0.30 |
107-18-6 | Allyl alcohol | 17 |
107-05-1 | Allyl chloride | 1.0 |
106-92-3 | Allyl glycidyl ether (AGE) | 77 |
2179-59-1 | Allyl propyl disulfide | 40.0 |
C7429-90-5 | Aluminum, Al alkyls | 6.7 |
7429-90-5 | Aluminum, as AL metal dust | 33 |
C7429-90-5 | Aluminum, as AL pyro powders | 17 |
C7429-90-5 | Aluminum, as Al soluble salts | 6.7 |
C7429-90-5 | Aluminum, as Al welding fumes | 17 |
504-29-0 | 2-Aminopyridine | 6.3 |
7664-41-7 | Ammonia | 100 |
12125-02-9 | Ammonium chloride fume | 33 |
3825-26-1 | Ammonium perfluorooctanoate | 0.33 |
7773-06-0 | Ammonium sulfamate | 33 |
628-63-7 | n-Amyl acetate | 1800 |
626-38-0 | sec-Amyl acetate | 2200 |
62-53-3 | Aniline & homologues | 1.0 |
29191-52-4 | Anisidine (o-,p- isomers) | 1.7 |
C7440-36-0 | Antimony & compounds as Sb | 1.7 |
1309-64-4 | Antimony trioxide, as Sb | 1.7 |
7784-42-1 | Arsine | 0.53 |
8052-42-4 | Asphalt (petroleum) fumes | 17 |
1912-24-9 | Atrazine | 17 |
86-50-0 | Azinphos-methyl | 0.67 |
C7440-39-3 | Barium, soluble compounds Ba | 1.7 |
17804-35-2 | Benomyl | 33 |
98-07-7 | Benzotrichloride | ----- |
94-36-0 | Benzoyl Peroxide | 17 |
100-44-7 | Benzyl chloride | 17 |
92-52-4 | Biphenyl | 4.3 |
1304-82-1 | Bismuth telluride | 33 |
1304-82-1 | Bismuth telluride Se doped | 17 |
C1303-96-4 | Borates, anhydrous | 3.3 |
C1303-96-4 | Borates, decahydrate | 17 |
C1303-96-4 | Borates, pentahydrate | 3.3 |
1303-86-2 | Boron oxide | 33 |
10294-33-4 | Boron tribromide | 33 |
76737-07-2 | Boron trifluoride | 9.3 |
314-40-9 | Bromacil | 33 |
7726-95-6 | Bromine | 2.2 |
7789-30-2 | Bromine pentafluoride | 2.4 |
106-97-8 | Butane | 6300.0 |
111-76-2 | 2-Butoxyethanol | 400 |
123-86-4 | n-Butyl acetate | 2400 |
105-46-4 | sec-Butyl acetate | 3200 |
540-88-5 | tert-Butyl acetate | 3200 |
141-32-2 | Butyl acrylate | 170 |
71-36-3 | n-Butyl alcohol | 500 |
78-92-2 | sec-Butyl alcohol | 1000 |
75-65-0 | tert-Butyl alcohol | 1000 |
1189-85-1 | tert-Butyl chromate, as CrO3 | 0.33 |
2426-08-6 | n-Butyl glycidyl ether (BGE) | 440 |
138-22-7 | n-Butyl lactate | 83 |
109-79-5 | n-Butyl mercaptan | 6.0 |
109-73-9 | n-Butylamine | 50.0 |
89-72-5 | o-sec-Butylphenol | 100 |
98-51-1 | p-tert-Butyltoluene | 200 |
156-62-7 | Calcium cyanamide | 1.7 |
1305-62-0 | Calcium hydroxide | 17 |
1305-78-8 | Calcium oxide | 6.7 |
76-22-2 | Camphor, synthetic | 40 |
105-60-2 | Caprolactam, dust | 3.3 |
105-60-2 | Caprolactam, vapor | 67 |
2425-06-1 | Captafol | 0.33 |
133-06-2 | Captan | 17 |
63-25-2 | Carbaryl | 17 |
1563-66-2 | Carbofuran | 0.33 |
1333-86-4 | Carbon black | 12 |
75-15-0 | Carbon disulfide | 100 |
558-13-4 | Carbon tetrabromide | 4.7 |
353-50-4 | Carbonyl fluoride | 18 |
463-58-1 | Carbonyl sulfide | ----- |
120-80-9 | Catechol | 77 |
21351-79-1 | Cesium hydroxide | 6.7 |
133-90-4 | Chloramben | ----- |
55720-99-5 | Chlorinated diphenyl oxide (hexachlorophenyl ether) | 1.7 |
7782-50-5 | Chlorine | 5.0 |
10049-04-4 | Chlorine dioxide | 0.2 |
7790-91-2 | Chlorine trifluoride | 1.3 |
600-25-9 | 1-Chloro-1-nitropropane | 33 |
107-20-0 | Chloroacetaldehyde | 11 |
79-11-8 | Chloroacetic acid | ----- |
532-27-4 | a-Chloroacetophenone | 1.1 |
79-04-9 | Chloroacetyl chloride | 0.67 |
2698-41-1 | o-Chlorobenylidene malonitrile | 1.3 |
108-90-7 | Chlorobenzene | 150 |
74-97-5 | Chlorobromomethane | 3500 |
75-45-6 | Chlorodifluoromethane | 12000 |
76-15-3 | Chloropentafluoroethane | 21000 |
76-06-2 | Chloropicrin | 2.2 |
2039-87-4 | o-Chlorostyrene | 940 |
95-49-8 | o-Chlorotoluene | 860 |
2921-88-2 | Chlorpyrifos | 0.67 |
C7440-47-3 | Chromium (II) compounds, as Cr | 1.7 |
C7440-47-3 | Chromium (III) compounds, Cr | 1.7 |
7440-47-3 | Chromium (metal) | 1.7 |
14977-61-8 | Chromyl chloride | 0.53 |
2971-90-6 | Clopidol | 33 |
7440-48-4 | Cobalt as Co metal Dust and fume | 0.17 |
10210-68-1 | Cobalt carbonyl as Co | 0.33 |
16842-03-8 | Cobalt hydrocarbonyl | 0.33 |
C7440-50-8 | Copper, Dusts and mists, as Cu | 3.3 |
7440-50-8 | Copper, Fume | 0.67 |
----- | Cotton dust, raw | 0.67 |
1319-77-3 | Cresol, all isomers | 73 |
4170-30-3 | Crotonaldehyde | 20 |
299-86-5 | Crufomate | 17 |
98-82-2 | Cumene | 820 |
420-04-2 | Cyanamide | 6.7 |
51-12-5 | Cyanides, as CN | 17 |
460-19-5 | Cyanogen | 67 |
506-77-4 | Cyanogen chloride | 2.5 |
110-82-7 | Cyclohexane | 3400 |
108-93-0 | Cyclohexanol | 690 |
108-94-1 | Cyclohexanone | 330 |
110-83-8 | Cyclohexene | 3400 |
108-91-8 | Cyclohexylamine | 140 |
121-82-4 | Cyclonite | 5.0 |
542-92-7 | Cyclopentadiene | 680 |
287-92-3 | Cyclopentane | 5700 |
13121-70-5 | Cyhexatin | 17 |
17702-41-9 | Decaborane | 0.83 |
8065-48-3 | Demeton | 0.83 |
123-42-2 | Diacetone alcohol | 790 |
333-41-5 | Diazinon | 0.33 |
334-88-3 | Diazomethane | 1.1 |
19287-45-7 | Diborane | 0.37 |
96-12-8 | 1,2-Dibromo-3-chloropropane | 0.20 |
107-66-4 | Dibutyl phosphate | 29 |
84-74-2 | Dibutyl phthalate | 17 |
102-81-8 | 2-N-Dibutylaminoethanol | 47 |
594-72-9 | 1,1-Dichloro-1-nitroethane | 40 |
118-52-5 | 1,3-Dichloro-5,5-Dimethyl hydantoin | 0.67 |
7572-29-4 | Dichloroacetylene | 1.3 |
95-50-1 | o-Dichlorobenzene (1,2-Dichlorobenzene) | 1000 |
75-71-8 | Dichlorodifluoromethane | 16000 |
75-34-3 | 1,1-Dichloroethane | 2700 |
540-59-0 | 1,2-Dichloroethylene | 2600 |
75-43-4 | Dichlorofluoromethane | 130 |
542-75-6 | Dichloropropene | 20 |
75-99-0 | 2,2-Dichloropropionic acid | 19 |
76-14-2 | Dichlorotetrafluoroethane | 23000 |
62-73-7 | Dichlorvas | 3.3 |
141-66-2 | Dicrotophos | 0.83 |
77-73-6 | Dicyclopentadiene | 100 |
102-54-5 | Dicyclopentadienyl iron | 33 |
111-42-2 | Diethanolamine | 43 |
96-22-0 | Diethyl ketone | 2300 |
84-66-2 | Diethyl phthalate | 17 |
64-67-5 | Diethyl sulfate | ----- |
109-89-7 | Diethylamine | 100 |
100-37-8 | Diethylaminoethanol | 170 |
111-40-0 | Diethylene triamine | 14 |
75-61-6 | Difluorodibromomethane | 2900 |
2238-07-5 | Diglycidyl ether | 1.7 |
108-83-8 | Diisobutyl ketone | 480 |
108-18-9 | Diisopropylamine | 67 |
127-19-5 | Dimethyl acetamide | 120 |
60-11-7 | Dimethyl aminoazobenzene | ----- |
79-44-7 | Dimethyl carbamoyl chloride | ----- |
124-40-3 | Dimethylamine | 60 |
121-69-7 | Dimethylaniline | 83 |
68-12-2 | Dimethylformamide | 30 |
57-14-7 | 1,1-Dimethylhydrazine | 4.0 |
131-11-3 | Dimethylphthalate | 17 |
148-01-6 | Dinitolmide | 17 |
534-52-1 | Dinitro-o-cresol | 0.67 |
528-29-0 | Dinitrobenzene, all isomers | 3.3 |
51-28-5 | 2,4-Dinitrophenol | ----- |
121-14-2 | 2,4-Dinitrotoluene | 5.0 |
78-34-2 | Dioxathion | 0.67 |
122-39-4 | Diphenylamine | 33 |
123-19-3 | Dipropyl ketone | 780 |
34590-94-8 | Dipropylene glycol methyl ether | 2000 |
85-00-7 | Diquat | 1.7 |
97-77-8 | Disulfiram | 6.7 |
298-04-4 | Disulfuton | 0.33 |
128-37-0 | 2,6-Ditert. butyl-p-cresol | 33 |
330-54-1 | Diuron | 33 |
1321-74-0 | Divinyl benzene | 180 |
2104-64-5 | EPN | 1.7 |
115-29-7 | Endosulfan | 0.33 |
72-20-8 | Endrin | 0.33 |
13838-16-9 | Enflurane | 1900 |
106-88-7 | 1,2-Epoxybutane | 20 |
141-43-5 | Ethanolamine | 25 |
563-12-2 | Ethion | 1.3 |
110-80-5 | 2-Ethoxyethanol | 200 |
111-15-9 | 2-Ethoxyethyl acetate | 90 |
141-78-6 | Ethyl acetate | 4800 |
140-88-5 | Ethyl acrylate | 66 |
64-17-5 | Ethyl alcohol | 6300 |
541-85-5 | Ethyl amyl ketone | 440 |
100-41-4 | Ethyl benzene | 1000 |
74-96-4 | Ethyl bromide | 3000 |
106-35-4 | Ethyl butyl ketone | 780 |
51-79-5 | Ethyl carbamate | ----- |
75-00-3 | Ethyl chloride | 10000 |
60-29-7 | Ethyl ether | 4000 |
109-94-4 | Ethyl formate | 1000 |
75-08-1 | Ethyl mercaptan | 4.3 |
78-10-4 | Ethyl silicate | 280 |
75-04-7 | Ethylamine | 60 |
107-07-3 | Ethylene chlorohydrin | 11 |
107-15-3 | Ethylene diamine | 83 |
107-21-1 | Ethylene glycol | 420 |
628-96-6 | Ethylene glycol dinitrate | 1.0 |
151-56-4 | Ethylenimine | 2.9 |
16219-75-3 | Ethylidene norbornene | 83 |
100-74-3 | N-Ethylmorpholine | 77 |
22224-92-6 | Fenamiphos | 0.33 |
115-90-2 | Fensulfothion | 0.33 |
55-38-9 | Fenthion | 0.67 |
14484-64-1 | Ferbam | 33 |
12604-58-9 | Ferrovanadium dust | 3.3 |
----- | Fibrous glass dust | 33 |
----- | Fine mineral fibers | 33 |
16984-48-8 | Fluorides, as F | 8.3 |
7782-41-4 | Fluorine | 5.3 |
944-22-9 | Fonofos | 0.33 |
75-12-7 | Formamide | 60 |
64-18-6 | Formic acid | 31 |
98-01-1 | Furfural | 26 |
98-00-1 | Furfuryl alcohol | 130 |
7782-65-2 | Germanium tetrahydride | 2.1 |
111-30-8 | Glutaraldehyde | 2.5 |
556-52-5 | Glycidol | 250 |
----- | Glycol ethers | ----- |
7440-58-6 | Hafnium | 1.7 |
151-67-7 | Halothane | 1300 |
142-82-5 | Heptane (n-Heptane) | 5500 |
87-68-3 | Hexachlorobutadiene | 0.70 |
77-47-4 | Hexachlorocyclopentadiene | 0.33 |
67-72-1 | Hexachloroethane | 32 |
1335-87-1 | Hexachloronaphthalene | 0.67 |
684-16-2 | Hexafluoroacetone | 2.3 |
822-06-0 | Hexamethylene diisocyanate | 0.11 |
100-54-3 | Hexane (n-Hexane) | 200 |
----- | Hexane, other isomers | 5900 |
591-78-6 | 2-Hexanone (MBK) | 67 |
108-84-9 | sec-Hexyl acetate | 980 |
107-41-5 | Hexylene glycol | 400 |
10035-10-6 | Hydrogen bromide | 33 |
7647-01-0 | Hydrogen chloride | 7.0 |
74-90-8 | Hydrogen cyanide | 37 |
7664-39-3 | Hydrogen fluoride, as F | 8.7 |
7722-84-1 | Hydrogen peroxide | 4.7 |
7783-07-5 | Hydrogen selenide, as Se | 0.53 |
7783-06-4 | Hydrogen sulfide | 0.9 |
123-31-9 | Hydroquinone | 6.7 |
999-61-1 | 2-Hydroxypropyl acrylate | 9.3 |
95-13-6 | Indene | 160 |
C7440-74-6 | Indium, & compounds as In | 0.33 |
7553-56-2 | Iodine | 3.3 |
75-47-8 | Iodoform | 33 |
1309-37-1 | Iron oxide fume, Fe2O3 as Fe | 17 |
13463-40-6 | Iron pentacarbonyl, as Fe | 0.83 |
----- | Iron salts, soluble as Fe | 3.3 |
123-92-2 | Isoamyl acetate | 1700 |
123-51-3 | Isoamyl alcohol | 1200 |
110-19-0 | Isobutyl acetate | 2400 |
78-83-1 | Isobutyl alcohol | 510 |
26952-21-6 | Isocytl alcohol | 890 |
78-59-1 | Isophorone | 93 |
4098-71-9 | Isophorone diisocyanate | 0.15 |
109-59-1 | Isopropoxyethanol | 350 |
108-21-4 | Isopropyl acetate | 3500 |
67-63-0 | Isopropyl alcohol | 3300 |
108-20-3 | Isopropyl ether | 3500 |
4016-14-2 | Isopropyl glycidyl ether (IGE) | 790 |
75-31-0 | Isopropylamine | 40 |
768-52-5 | N-Isopropylaniline | 37 |
463-51-4 | Ketene | 2.9 |
3687-31-8 | Lead arsenate, as Pb3 (A2O4)2 | 0.50 |
7758-97-6 | Lead chromate, as Cr | 0.040 |
68476-85-7 | Liquified petroleum gas | 6000 |
7580-67-8 | Lithium hydride | 0.080 |
1309-48-4 | Magnesium oxide fume | 33 |
121-75-5 | Malathion | 33 |
108-31-6 | Maleic anhydride | 3.3 |
C7439-96-5 | Manganese dust & compounds | 0.40 |
C7439-96-5 | Manganese fume | 3.3 |
12079-65-1 | Manganese cyclopentadienyl tricarbonyl | 0.33 |
C7439-97-6 | Mercury, Aryl & inorganic cmpd | 0.33 |
C7439-97-6 | Mercury, as Hg Alkyl compounds | 0.33 |
C7439-97-6 | Mercury, vapors except alkyl | 0.17 |
141-79-7 | Mesityl oxide | 200 |
79-41-4 | Methacrylic acid | 230 |
16752-77-5 | Methomyl | 8.3 |
72-43-5 | Methoxychlor | 33 |
109-86-4 | 2-Methoxyethanol | 20 |
110-49-6 | 2-Methoxyethyl acetate | 80 |
150-76-5 | 4-Methoxyphenol | 17 |
137-05-3 | Methyl 2-cyanoacrylate | 30 |
79-20-9 | Methyl acetate | 2000 |
74-99-7 | Methyl acetylene | 5500 |
59355-75-8 | Methyl acetylene-propadiene mixture (MAPP) | 5500 |
96-33-3 | Methyl acrylate | 120 |
67-56-1 | Methyl alcohol | 870 |
100-61-8 | N-Methyl aniline | 7.3 |
74-83-9 | Methyl bromide | 5.0 |
74-87-3 | Methyl chloride | 340 |
71-55-6 | Methyl chloroform (1,1,1-Trichloroethane) | 6400 |
8022-00-2 | Methyl demeton | 1.7 |
78-93-3 | Methyl ethyl ketone (MEK) | 1000 |
1338-23-4 | Methyl ethyl ketone peroxide | 5.0 |
107-31-3 | Methyl formate | 820 |
60-34-4 | Methyl hydrazine | 1.2 |
74-88-4 | Methyl iodide | 40 |
110-12-3 | Methyl isoamyl ketone | 780 |
108-11-2 | Methyl isobutyl carbinol | 350 |
108-10-1 | Methyl isobutyl ketone (MIBK) | 680 |
624-83-9 | Methyl isocyanate | 0.16 |
563-80-4 | Methyl isopropyl ketone | 2300 |
74-93-1 | Methyl mercaptan | 3.3 |
80-62-6 | Methyl methacrylate | 1400 |
110-43-0 | Methyl n-amyl ketone | 780 |
591-78-6 | Methyl n-butyl ketone | 67 |
298-00-0 | Methyl parathion | 0.67 |
107-87-9 | Methyl propyl ketone | 2300 |
681-84-5 | Methyl silicate | 20 |
1634-04-4 | Methyl tert-butyl ether | 500 |
98-83-9 | a-Methyl styrene | 810 |
126-98-7 | Methylacrylonitrile 9.0 | 9.0 |
109-87-5 | Methylal | 10000 |
74-89-5 | Methylamine | 43 |
108-87-2 | Methylcyclohexane | 5400 |
25639-42-3 | Methylcyclohexanol | 780 |
583-60-8 | o-Methylcyclohexanone | 760 |
12108-13-3 | Methylcyclopentadienyl manganese tricarbonyl | 0.67 |
5124-30-1 | Methylene bis (4-cyclo-hexylisocyanate) | 0.18 |
101-68-8 | Methylene bis(phenyl isocyanate) | 0.2 |
21087-64-9 | Metribuzin | 17 |
7786-34-7 | Mevinphos | 0.33 |
C7439-98-7 | Molybdenum, as Mo soluble cpds | 17 |
C7439-98-7 | Molybdenum, insoluble cpds | 33 |
6923-22-4 | Monocrotophos | 0.83 |
110-91-8 | Morpholine | 240 |
300-76-5 | Naled | 10 |
91-20-3 | Napthalene | 170 |
54-11-5 | Nicotine | 1.7 |
1929-82-4 | Nitrapyrin | 33 |
7697-37-2 | Nitric acid | 17 |
10102-43-9 | Nitric oxide | 100 |
100-01-6 | p-Nitroaniline | 10 |
98-95-3 | Nitrobenzene | 1.7 |
100-00-5 | p-Nitrochlorobenzene | 2.0 |
79-24-3 | Nitroethane | 1000 |
7783-54-2 | Nitrogen trifluoride | 97 |
92-93-3 | 4-Nitrobiphenyl | ----- |
55-63-0 | Nitroglycerin | 1.5 |
75-52-5 | Nitromethane | 830 |
100-02-7 | 4-Nitrophenol | ----- |
108-03-2 | 1-Nitropropane | 20 |
684-93-5 | N-Nitroso-N-methylurea | ----- |
88-72-2 | Nitrotoluene | 37 |
111-84-2 | Nonane | 3500 |
2234-13-1 | Octachloronaphthalene | 0.33 |
111-65-9 | Octane | 4700 |
8012-95-1 | Oil mist, mineral | 17 |
20816-12-0 | Osmium tetroxide, as Os | 0.0053 |
144-62-7 | Oxalic acid | 3.3 |
7783-41-7 | Oxygen difluoride | 0.37 |
8002-74-2 | Parafin wax fume | 6.7 |
4685-14-7 | Paraquat | 4.5 |
56-38-2 | Parathion | 0.33 |
19624-22-7 | Pentaborane | 0.043 |
1321-64-8 | Pentachloronaphthalene | 1.7 |
82-68-8 | Pentachloronitrobenzene (quintobenzene) | 1.7 |
109-66-0 | Pentane | 6000 |
594-42-3 | Perchloromethyl mercaptan | 2.5 |
7616-94-6 | Perchloryl fluoride | 43 |
108-95-2 | Phenol | 63 |
92-84-2 | Phenothiazine | 1.7 |
101-84-8 | Phenyl ether | 23 |
122-60-1 | Phenyl glycidyl ether | 2000 |
108-98-5 | Phenyl mercaptan | 7.7 |
106-50-3 | p-Phenylenediamine | 0.33 |
100-63-0 | Phenylhydrazine | 1.5 |
638-21-1 | Phenylphosphine | 0.77 |
298-02-2 | Phorate | 0.17 |
75-44-5 | Phosgene | 1.3 |
7803-51-2 | Phosphine | 1.3 |
7664-38-2 | Phosphoric acid | 3.3 |
7723-14-0 | Phosphorus | 0.33 |
10025-87-3 | Phosphorus oxychloride | 2.1 |
10026-13-8 | Phosphorus pentachloride | 2.8 |
1314-80-3 | Phosphorus pentasulfide | 3.3 |
7719-12-2 | Phosphorus trichloride | 3.7 |
85-44-9 | Phthalic anhydride | 20 |
626-17-5 | m-Phthalodinitrile | 17 |
1918-02-1 | Picloram | 33 |
88-89-1 | Picric acid | 0.33 |
83-26-1 | Pindone | 0.033 |
142-64-3 | Piperazine dihydrochloride | 17 |
7440-06-4 | Platinum, Metal | 3.3 |
C7440-06-4 | Platinum, Soluble salts as Pt | 0.0067 |
1310-58-3 | Potassium hydroxide | 6.7 |
107-19-7 | Propargyl alcohol | 7.7 |
57-57-8 | B-Propiolactone | 5.0 |
123-38-6 | Propionaldehyde | ----- |
114-26-1 | Propoxur | 1.7 |
79-09-4 | Propionic acid | 100 |
109-60-4 | n-Propyl acetate | 2800 |
71-23-8 | n-Propyl alcohol | 1600 |
627-13-4 | n-Propyl nitrate | 360 |
6423-43-4 | Propylene glycol dinitrate | 1.1 |
107-98-2 | Propylene glycol monomethyl ether | 2000 |
75-55-8 | Propylene imine | 16 |
8003-34-7 | Pyrethrum | 1.7 |
110-86-1 | Pyridine | 53 |
91-22-5 | Quinoline | ----- |
106-51-4 | Quinone | 1.5 |
108-46-3 | Resorcinol | 150 |
7440-16-6 | Rhodium Metal | 3.3 |
C7440-16-6 | Rhodium, Insoluble compounds | 3.3 |
C7440-16-6 | Rhodium, Soluble compounds | 0.033 |
299-84-3 | Ronnel | 33 |
83-79-4 | Rotenone | 17 |
----- | Rubber solvent (Naphtha) | 5300 |
C7782-49-2 | Selenium compounds, as Se | 0.67 |
7783-79-1 | Selenium hexafluoride, as Se | 0.53 |
136-78-7 | Sesone | 33 |
7803-62-5 | Silicon tetrahydride | 22 |
7440-22-4 | Silver, Metal | 0.33 |
C7440-22-4 | Silver, soluble compounds as Ag | 0.033 |
26628-22-8 | Sodium azide | 1.0 |
7631-90-5 | Sodium bisulfite | 17 |
62-74-8 | Sodium fluoroacetate | 0.17 |
1310-73-2 | Sodium hydroxide | 6.7 |
7681-57-4 | Sodium metabisulfite | 17 |
7803-52-3 | Stibine | 1.7 |
57-24-9 | Strychnine | 0.5 |
100-42-5 | Styrene | 1000 |
96-9-3 | Styrene oxide | ----- |
1395-21-7 | Subtilisins | 0.0002 |
3689-24-5 | Sulfotep | 0.67 |
2551-62-4 | Sulfur hexafluoride | 20000 |
10025-67-9 | Sulfur monochloride | 18 |
5714-22-7 | Sulfur pentafluoride | 0.33 |
7783-60-0 | Sulfur tetrafluoride | 1.5 |
7664-93-9 | Sulfuric acid | 3.3 |
2699-79-8 | Sulfuryl fluoride | 67 |
35400-43-2 | Sulprofos | 3.3 |
93-76-5 | 2,4,5-T | 33 |
107-49-3 | TEPP | 0.16 |
C7440-25-7 | Tantalum, metal & oxide dusts | 17 |
C13494-80-9 | Tellurium & compounds as Te | 0.33 |
7783-80-4 | Tellurium hexafluoride, as Te | 0.33 |
3383-96-8 | Temephos | 33 |
26140-60-3 | Terphenyls | 16 |
76-12-0 | 1,1,2,2-Tetrachloro-1,2-difluoroethane | 14000 |
76-11-9 | 1,1,1,2-Tetrachloro-2,2-difluoroethane | 14000 |
79-34-5 | 1,1,2,2-Tetrachloroethane | 23 |
1335-88-2 | Tetrachloronaphthalene | 6.7 |
78-00-2 | Tetraethyl lead, as Pb | 0.33 |
109-99-9 | Tetrahydrofuran | 2000 |
75-74-1 | Tetramethyl lead, as Pb | 0.5 |
3333-52-6 | Tetramethyl succinonitrile | 9.3 |
509-14-8 | Tetranitromethane | 27 |
7722-88-5 | Tetrasodium pyrophosphate | 17 |
479-45-8 | Tetryl | 5.0 |
C7440-28-0 | Thallium, soluble compounds, Tl | 0.33 |
96-69-5 | 4,4-Thiobis(6-tert, butyl-m-cresol) | 33 |
68-11-1 | Thioglycolic acid | 13 |
7719-09-7 | Thionyl chloride | 16 |
137-26-8 | Thiram | 3.3 |
7440-31-5 | Tin, Metal | 6.7 |
C7440-31-5 | Tin, Organic compounds, as Sn | 0.33 |
7440-31-5 | Tin, oxide & inorganic except SnH4 | 6.7 |
7550-45-0 | Titanium tetrachloride | ----- |
108-88-3 | Toluene | 400 |
108-44-1 | m-Toluidine | 29 |
106-49-0 | p-Toluidine | 29 |
126-73-8 | Tributyl phosphate | 7.3 |
76-13-1 | 1,1,2-Trichloro-1,2,2-trifluorethane | 27000 |
76-03-9 | Trichloroacetic acid | 22 |
120-82-1 | 1,2,4-Trichlorobenzene | 120 |
79-00-5 | 1,1,2-Trichloroethane | 180 |
75-69-4 | Trichlorofluoromethane | 19000 |
1321-65-9 | Trichloronaphthalene | 17 |
95-95-4 | 2,4,5-Trichlorophenol | ----- |
96-18-4 | 1,2,3-Trichloropropane | 200 |
121-44-8 | Triethylamine | 7.0 |
75-63-8 | Trifluorobromomethane | 20000 |
1582-09-8 | Trifluralin | ----- |
552-30-7 | Trimellitic anhydride | 0.13 |
2551-13-7 | Trimethyl benzene | 420 |
540-84-1 | 2,2,4-Trimethylpentane | ----- |
121-45-9 | Trimethyl phosphite | 33 |
75-50-3 | Trimethylamine | 80 |
118-96-7 | 2,4,6-Trinitrotoluene | 1.7 |
78-30-8 | Triorthocresyl phosphate | 0.33 |
603-34-9 | Triphenyl amine | 17 |
115-86-6 | Triphenyl phosphate | 10 |
C7440-33-7 | Tungsten, Insoluble compounds | 17 |
C7440-33-7 | Tungsten, Soluble compounds | 3.3 |
8006-64-2 | Turpentine | 1900 |
C7440-61-1 | Uranium, insoluble & soluble | 0.67 |
8032-32-4 | VM & P Naphtha | 4600 |
110-62-3 | n-Valeraldehyde | 590 |
1314-62-1 | Vanadium, as V2O5 | 0.17 |
108-05-4 | Vinyl acetate | 200 |
593-60-2 | Vinyl bromide | 73 |
106-87-6 | Vinyl cyclohexene dioxide | 200 |
75-35-4 | Vinylidene chloride | 67 |
25013-15-4 | Vinyl toluene | 800 |
81-81-2 | Warfarin | 0.33 |
----- | Welding fumes | 17 |
1477-55-0 | m-Xylene a,a'-diamine | 0.33 |
1330-20-7 | Xylenes (m-,o-,p-isomers) | 1500 |
1300-73-8 | Xylidine | 8.3 |
C7440-65-5 | Yttrium, metal and cpds as Y | 3.3 |
7646-85-7 | Zinc chloride fume | 3.3 |
13530-65-9 | Zinc chromates | 0.033 |
1314-13-2 | Zinc oxide, fume | 17 |
C7440-67-7 | Zirconium compounds, as Zr | 17 |
Hazardous Air Pollutants
This appendix contains a list of the hazardous air pollutants (HAP) created by FCAA, Section 112.
Chemical Abstract Service Number |
Chemical Name | Comments |
75070 | Acetaldehyde | |
60355 | Acetamide | |
75058 | Acetonitrile | |
98862 | Acetophenone | |
53963 | 2-Acetylaminofluorene | |
107028 | Acrolein | |
79061 | Acrylamide | |
79107 | Acrylic acid | |
107131 | Acrylonitrile | |
107051 | Allyl chloride | |
92671 | 4-Aminobiphenyl | |
62533 | Aniline | |
90040 | o-Anisidine | |
1332214 | Asbestos | |
71432 | Benzene (including benzene from gasoline) | |
92875 | Benzidine | |
98077 | Benzotrichloride | |
100447 | Benzyl chloride | |
92524 | Biphenyl | |
117817 | Bis(2-ethylhexyl)phthalate (DEHP) | |
542881 | Bis(chloromethyl)ether | |
75252 | Bromoform | |
106990 | 1,3-Butadiene | |
156627 | Calcium cyanamide | |
105602 | Caprolactam | EPA delisted June 18, 1996. |
133062 | Captan | |
63252 | Carbaryl | |
75150 | Carbon disulfide | |
56235 | Carbon tetrachloride | |
463581 | Carbonyl sulfide | |
120809 | Catechol | |
133904 | Chloramben | |
57749 | Chlordane | |
7782505 | Chlorine | |
79118 | Chloroacetic acid | |
532274 | 2-Chloroacetophenone | |
108907 | Chlorobenzene | |
510156 | Chlorobenzilate | |
67663 | Chloroform | |
107302 | Chloromethyl methyl ether | |
126998 | Chloroprene | |
1319773 | Cresols/Cresylic acid (isomers and mixture) | |
95487 | o-Cresol | |
108394 | m-Cresol | |
106445 | p-Cresol | |
98828 | Cumene | |
94757 | 2,4-D, salts and esters | |
3547044 | DDE | |
334883 | Diazomethane | |
132649 | Dibenzofurans | |
96128 | 1,2-Dibromo-3-chloropropane | |
84742 | Dibutylphthalate | |
106467 | 1,4-Dichlorobenzene(p) | |
91941 | 3,3-Dichlorobenzidene | |
111444 | Dichloroethyl ether (Bis(2-chloroethyl)ether) | |
542756 | 1,3-Dichloropropene | |
62737 | Dichlorvos | |
111422 | Diethanolamine | |
121697 | N,N-Diethyl aniline (N,N-Dimethylaniline) | |
64675 | Diethyl sulfate | |
119904 | 3,3-Dimethoxybenzidine | |
60117 | Dimethyl aminoazobenzene | |
119937 | 3,3¬-Dimethyl benzidine | |
79447 | Dimethyl carbamoyl chloride | |
68122 | Dimethyl formamide | |
57147 | 1,1-Dimethyl hydrazine | |
131113 | Dimethyl phthalate | |
77781 | Dimethyl sulfate | |
534521 | 4,6-Dinitro-o-cresol, and salts | |
51285 | 2,4-Dinitrophenol | |
121142 | 2,4-Dinitrotoluene | |
123911 | 1,4-Dioxane (1,4-Diethyleneoxide) | |
122667 | 1,2-Diphenylhydrazine | |
106898 | Epichlorohydrin (l-Chloro-2,3-epoxypropane) | |
106887 | 1,2-Epoxybutane | |
140885 | Ethyl acrylate | |
100414 | Ethyl benzene | |
51796 | Ethyl carbamate (Urethane) | |
75003 | Ethyl chloride (Chloroethane) | |
106934 | Ethylene dibromide (Dibromoethane) | |
107062 | Ethylene dichloride (1,2-Dichloroethane) | |
107211 | Ethylene glycol | |
151564 | Ethylene imine (Aziridine) | |
75218 | Ethylene oxide | |
96457 | Ethylene thiourea | |
75343 | Ethylidene dichloride (1,1-Dichloroethane) | |
50000 | Formaldehyde | |
76448 | Heptachlor | |
118741 | Hexachlorobenzene | |
87683 | Hexachlorobutadiene | |
77474 | Hexachlorocyclopentadiene | |
67721 | Hexachloroethane | |
822060 | Hexamethylene-1,6-diisocyanate | |
680319 | Hexamethylphosphoramide | |
110543 | Hexane | |
302012 | Hydrazine | |
7647010 | Hydrochloric acid | |
7664393 | Hydrogen fluoride (Hydrofluoric acid) | |
7783064 | Hydrogen sulfide | Included in error and removed on Dec. 4, 1991. |
123319 | Hydroquinone | |
78591 | Isophorone | |
58899 | Lindane (all isomers) | |
108316 | Maleic anhydride | |
67561 | Methanol | |
72435 | Methoxychlor | |
74839 | Methyl bromide (Bromomethane) | |
74873 | Methyl chloride (Chloromethane) | |
71556 | Methyl chloroform (1,1,1-Trichloroethane) | |
78933 | Methyl ethyl ketone (2-Butanone) | |
60344 | Methyl hydrazine | |
74884 | Methyl iodide (Iodomethane) | |
108101 | Methyl isobutyl ketone (Hexone) | |
624839 | Methyl isocyanate | |
80626 | Methyl methacrylate | |
1634044 | Methyl tert butyl ether | |
101144 | 4,4-Methylene bis(2-chloroaniline) | |
75092 | Methylene chloride (Dichloromethane) | |
101688 | Methylene diphenyl diisocyanate (MDI) | |
101779 | 4,4¬-Methylenedianiline | |
91203 | Naphthalene | |
98953 | Nitrobenzene | |
92933 | 4-Nitrobiphenyl | |
100027 | 4-Nitrophenol | |
79469 | 2-Nitropropane | |
684935 | N-Nitroso-N-methylurea | |
62759 | N-Nitrosodimethylamine | |
59892 | N-Nitrosomorpholine | |
56382 | Parathion | |
82688 | Pentachloronitrobenzene (Quintobenzene) | |
87865 | Pentachlorophenol | |
108952 | Phenol | |
106503 | p-Phenylenediamine | |
75445 | Phosgene | |
7803512 | Phosphine | |
7723140 | Phosphorus | |
85449 | Phthalic anhydride | |
1336363 | Polychlorinated biphenyls (Aroclors) | |
1120714 | 1,3-Propane sultone | |
57578 | beta-Propiolactone | |
123386 | Propionaldehyde | |
114261 | Propoxur (Baygon) | |
78875 | Propylene dichloride (1,2-Dichloropropane) | |
75569 | Propylene oxide | |
75558 | 1,2-Propylenimine (2-Methyl aziridine) | |
91225 | Quinoline | |
106514 | Quinone | |
100425 | Styrene | |
96093 | Styrene oxide | |
1746016 | 2,3,7,8-Tetrachlorodibenzo-p-dioxin | |
79345 | 1,1,2,2-Tetrachloroethane | |
127184 | Tetrachloroethylene (Perchloroethylene) | |
7550450 | Titanium tetrachloride | |
108883 | Toluene | |
95807 | 2,4-Toluene diamine | |
584849 | 2,4-Toluene diisocyanate | |
95534 | o-Toluidine | |
8001352 | Toxaphene (chlorinated camphene) | |
120821 | 1,2,4-Trichlorobenzene | |
79005 | 1,1,2-Trichloroethane | |
79016 | Trichloroethylene | |
95954 | 2,4,5-Trichlorophenol | |
88062 | 2,4,6-Trichlorophenol | |
121448 | Triethylamine | |
1582098 | Trifluralin | |
540841 | 2,2,4-Trimethylpentane | |
108054 | Vinyl acetate | |
593602 | Vinyl bromide | |
75014 | Vinyl chloride | |
75354 | Vinylidene chloride (1,1-Dichloroethylene) | |
1330207 | Xylenes (isomers and mixture) | |
95476 | o-Xylenes | |
108383 | m-Xylenes | |
10642 | p-Xylenes | |
0 | Antimony Compounds | |
0 | Arsenic Compounds (inorganic including arsine) | |
0 | Beryllium Compounds | |
0 | Cadmium Compounds | |
0 | Chromium Compounds | |
0 | Cobalt Compounds | |
0 | Coke Oven Emissions | |
0 | Cyanide Compounds1 | |
0 | Glycol ethers2 | |
0 | Lead Compounds | |
0 | Manganese Compounds | |
0 | Mercury Compounds | |
0 | Fine mineral fibers3 | |
0 | Nickel Compounds | |
0 | Polycylic Organic Matter4 | |
0 | Radionuclides (including radon)5 | |
0 | Selenium Compounds |
Reviser's note: The typographical errors in the above material occurred in the copy filed by the Yakima Regional Clean Air Authority and appear in the Register pursuant to the requirements of RCW 34.08.040.
Reviser's note: The spelling errors in the above material occurred in the copy filed by the Yakima Regional Clean Air Authority and appear in the Register pursuant to the requirements of RCW 34.08.040.