SHB 1876 -
By Senator Kohl-Welles
Strike everything after the enacting clause and insert the following:
"NEW SECTION. Sec. 1
(1) "Air conditioning and heating equipment" means equipment
necessary for any system that heats, cools, conditions, ventilates,
filters, humidifies, or dehumidifies environmental air for residential,
industrial, or commercial use. Air conditioning and heating equipment
includes both oil and fuel gas furnaces. It does not include duct
work.
(2) "Air conditioning and heating work" means to design, construct,
install, modify, service, repair, and replace air conditioning and
heating equipment and systems. It does not mean to fabricate and
install duct systems.
(3) "Board" means the HVAC/R board established in section 30 of
this act.
(4) "Boiler" means a closed vessel in which water is heated, steam
is generated, steam is superheated, or a combination thereof, under
pressure or vacuum by the application of heat, electricity, or nuclear
energy. "Boiler" also includes fired units for heating or vaporizing
liquids other than water where these systems are complete within
themselves.
(5) "BTUH" means British thermal units per hour.
(6) "CFM" means cubic feet per minute.
(7) "Contractor" means any person, corporate or otherwise, who is
registered as a contractor by the department under section 2 of this
act.
(8) "Department" means the department of labor and industries.
(9) "Director" means the director of the department or the
director's designee.
(10) "Gas piping" means pipes, valves, or fittings used to convey
fuel gas installed on a premise or in a building. "Gas piping" does
not include service piping.
(11) "Gas piping work" means to design, fabricate, construct,
install, modify, or repair gas piping and ventilation related to gas
piping.
(12) "HVAC/R" means heating, ventilating, air conditioning, and
refrigeration.
(13) "HVAC/R contractor" means any person, corporate or otherwise,
who engages in, or offers or advertises to engage in, any HVAC/R work
covered by the provisions of this chapter by way of trade or business,
or any person, corporate or otherwise, who employs anyone, or offers or
advertises to employ anyone, to engage in any HVAC/R work covered by
the provisions of this chapter.
(14)(a) "HVAC/R equipment" means mechanical equipment necessary for
any system that heats, cools, conditions, ventilates, filters,
humidifies, or dehumidifies environmental air for residential,
industrial, or commercial use. HVAC/R equipment includes oil furnaces,
fuel gas furnaces, and duct systems.
(b) "HVAC/R equipment and systems" does not include: (i) Single,
stand-alone line voltage equipment or components, such as heat cables,
wall heaters, radiant panel heaters, baseboard heaters, contactors,
motor starters, and similar equipment unless the equipment or component
is exclusively controlled by the HVAC/R system and requires an
additional external connection to a mechanical system, or contains an
HVAC/R mechanical system within the equipment; (ii) solid fuel burning
devices, such as wood stoves and coal stoves; (iii) mechanical piping
other than that necessary to deliver fuel; or (iv) boilers.
(15) "HVAC/R service" means to repair, modify, service, and perform
other work required for the normal continued performance of an HVAC/R
system. "HVAC/R service" does not mean to install or replace a system.
(16) "HVAC/R work" means to design, fabricate, construct, install,
modify, or repair HVAC/R equipment.
(17) "Indirect system" means a system in which a secondary coolant,
cooled or heated by the refrigeration system, is circulated to the air
or other substance to be cooled or heated.
(18) "Mechanic" means a person who has been issued a certificate of
competency by the department under section 14 of this act or a
temporary permit under section 19 of this act to perform work under
this chapter.
(19) "Property management company" means a company that is
operating in compliance with state real estate licensing rules and is
under contract with the property owner to manage the buildings.
(20) "Refrigeration system" means a combination of interconnected
refrigerant-containing parts constituting one closed refrigerant
circuit in which a refrigerant is circulated for the purpose of
extracting heat. "Refrigeration system" includes not only the direct
system but also the indirect system.
(21) "Refrigeration work" means to design, fabricate, construct,
install, modify, service, replace, or repair refrigeration systems.
(22) "Sheet metal work" means to design, fabricate, construct,
install, modify, service, replace, repair or test, or adjust and
balance HVAC/R equipment and systems. "Sheet metal work" includes the
fabrication and installation of duct systems.
(23) "Technical college" means a public community or technical
college, or a not-for-profit nationally accredited technical or trade
school licensed by the workforce training and education coordinating
board under chapter 28C.10 RCW.
(24) "Trainee" means a person who has been issued a training
certificate by the department under section 15 of this act or chapter
19.28 RCW to perform work under this chapter or chapter 19.28 RCW.
(25) "Valid" means not expired, revoked, or suspended.
NEW SECTION. Sec. 2
(a) Any person, firm, partnership, corporation, or other entity to
advertise, offer to do work, submit a bid, engage in, conduct, or carry
on the business of performing HVAC/R work without having a valid
registration as a contractor under chapter 18.27 RCW;
(b) Any person, firm, or company to advertise, offer to do, or do
the business of an HVAC/R contractor as defined in this chapter, within
the state, unless they have been issued an HVAC/R contractor
registration from the department. The department shall prescribe an
application form to be used to apply for a contractor registration
under this chapter and shall require the HVAC/R contractor to also be
a registered general or specialty contractor under chapter 18.27 RCW
prior to being issued an HVAC/R contractor registration. The document
issued by the department indicating the person, firm, partnership,
corporation, or other entity is registered as an HVAC/R contractor
under this chapter and a registered contractor under chapter 18.27 RCW
shall be the same document. Regardless of when the HVAC/R contractor
registration was issued, it shall be suspended, be revoked, expire, or
be renewed at the same time as the contractor registration under
chapter 18.27 RCW;
(c) On and after January 1, 2009, any person, firm, partnership,
corporation, or other entity to employ a person to perform or offer to
perform HVAC/R work who has not been issued a certificate or temporary
permit by the department under this chapter; and
(d) On and after January 1, 2009, any person to perform HVAC/R work
without having in his or her possession a certificate or permit issued
by the department under this chapter.
(2) No political subdivision shall require a person possessing a
certificate or permit issued by the department under this chapter to
demonstrate any additional proof of competency, obtain any license, or
pay any fee to perform HVAC/R work.
(3) An HVAC/R sheet metal manufacturer or fabricator, and its
employees, may opt out of the HVAC/R certification requirement of this
section. For purposes of this section, a "sheet metal manufacturer or
fabricator" means an entity that produces duct work for installation
on-site. The term "manufacturer" does not include bidding the product
or installing or subcontracting the installation.
NEW SECTION. Sec. 3
(2) No contractor may advertise, offer to do work, submit a bid, or
perform any work under this chapter without being registered as an
HVAC/R contractor under this chapter and chapter 18.27 RCW.
NEW SECTION. Sec. 4
NEW SECTION. Sec. 5
NEW SECTION. Sec. 6
NEW SECTION. Sec. 7
(1) HVAC/R mechanic I. A holder of this certificate has acquired
the necessary experience and passed the appropriate examination(s) for
the following:
(a) Gas piping. This specialty may perform gas piping and
ventilation related to gas piping work on fuel burning appliances with
a maximum capacity of five hundred thousand BTUH.
(b) Sheet metal. This specialty may perform HVAC/R work on HVAC/R
equipment of seven and one-half tons or less for air conditioning and
three thousand three hundred seventy-five CFM or less. This specialty
does not include the installation of refrigeration piping and gas
piping.
(c) Refrigeration. This specialty may perform refrigeration and
other mechanical work required for normal continued performance on a
refrigeration system not exceeding ninety thousand BTUH per compressor
using class A1 refrigerants.
(d) Air conditioning and heating. This specialty may perform air
conditioning and heating work on air conditioning and heating equipment
of seven and one-half tons or less for air conditioning and three
thousand three hundred seventy-five CFM or less. This specialty does
not include the fabrication and installation of duct work.
(2) HVAC/R mechanic II. A holder of this certificate has acquired
the necessary experience and passed the appropriate examination(s) for
the following:
(a) Gas piping. This specialty may perform gas piping and
ventilation related to gas piping work on fuel burning appliances with
a maximum capacity of five hundred thousand BTUH.
(b) Sheet metal. This specialty may perform HVAC/R work on HVAC/R
equipment of twenty tons or less for air conditioning and nine thousand
CFM or less. This specialty does not include the installation of
refrigeration and gas piping.
(c) Refrigeration. This specialty may perform refrigeration and
other mechanical work, except for installation, required for normal
continued performance on a refrigeration system with one or more
compressors not exceeding three hundred thousand BTUH per compressor
using class A1 refrigerants. A refrigeration mechanic II may install
or replace a self-contained refrigeration system up to three hundred
thousand BTUH.
(d) Air conditioning and heating. This specialty may perform air
conditioning and heating work on air conditioning and heating equipment
of twenty tons or less for air conditioning and nine thousand CFM or
less. This specialty does not include the fabrication and installation
of duct work.
(3) HVAC/R mechanic III. A holder of this certificate has acquired
the necessary experience and passed the appropriate examination(s) for
the following:
(a) Gas piping. This specialty may perform all gas piping work on
fuel burning appliances and systems.
(b) Sheet metal. This specialty may perform all sheet metal work
on HVAC/R equipment and systems. This specialty does not include the
installation of refrigeration or gas piping.
(c) Refrigeration. This specialty may perform refrigeration work
on any refrigeration system using any refrigerant.
(d) Air conditioning and heating. This specialty may perform air
conditioning and heating work on all air conditioning and heating
equipment. This specialty does not include the fabrication and
installation of duct systems.
NEW SECTION. Sec. 8
(2) An HVAC/R mechanic from another state or country applying for
a certificate of competency or any specialty must provide evidence in
a form prescribed by the department affirming that the person has the
equivalent qualifications to those required under section 12 of this
act.
NEW SECTION. Sec. 9
(a) HVAC/R mechanic I. To be eligible to take the examination for
an HVAC/R mechanic I certificate of competency, or any associated
specialty, the applicant must have:
(i) Performed HVAC/R work for a minimum of one thousand hours under
the supervision of a certified HVAC/R mechanic for one hundred percent
of the one thousand hours;
(ii) Performed HVAC/R work for a minimum of two thousand hours
under the supervision of a certified HVAC/R mechanic for seventy-five
percent of the two thousand hours; or
(iii) Successfully completed an apprenticeship program approved
under chapter 49.04 RCW that meets the requirements of this
certification or any associated specialties.
(b) Once the applicant has passed the HVAC/R mechanic I exam and
performed the required HVAC/R work under (a)(i) of this subsection he
or she may work unsupervised for the remaining one thousand hours of
required work experience, but may not supervise other trainees until
the applicant has received his or her certification after completion of
the full two thousand hours of on-the-job training.
(c) HVAC/R mechanic II. To be eligible to take the examination for
an HVAC/R mechanic II certificate of competency, or any associated
specialty, the applicant must have:
(i) Performed HVAC/R work for a minimum of four thousand hours
under the supervision of a certified HVAC/R mechanic for seventy-five
percent of the four thousand hours; or
(ii) Successfully completed an apprenticeship program approved
under chapter 49.04 RCW that meets the requirements of this
certification or any associated specialties.
(d) The applicant for the mechanic II exam under (c) of this
subsection must complete the four thousand hours of work experience
before he or she is eligible to take the appropriate exams.
(e) HVAC/R mechanic III. To be eligible to take the examination
for an HVAC/R mechanic III certificate of competency, or any associated
specialties, the applicant must have:
(i) Performed HVAC/R work for a minimum of six thousand hours under
the supervision of a certified HVAC/R mechanic for seventy-five percent
of the six thousand hours;
(ii) Performed HVAC/R work for a minimum of eight thousand hours
under the supervision of a certified HVAC/R mechanic for seventy-five
percent of the eight thousand hours; or
(iii) Successfully completed an apprenticeship program under
chapter 49.04 RCW that meets the requirements of this certification or
any associated specialties.
(f) Once the applicant has passed the HVAC/R mechanic III exam and
performed the required HVAC/R work under (e)(i) of this subsection he
or she may work unsupervised for the remaining two thousand hours of
required work experience, but may not supervise other trainees until
the applicant receives his or her certification after completion of the
full eight thousand hours of on-the-job training.
(2) Any on-the-job training under the proper supervision as
required by this chapter, and by an individual holding all proper
approved trainee cards, will count toward all required on-the-job
training hours for the HVAC/R mechanic and all associated specialties.
(3) Upon determining that the applicant is eligible to take the
examination, the department shall so notify the applicant, indicating
the time and place for taking the examination.
(4) No noncertified individual may work unsupervised more than one
year beyond the date when the trainee would be eligible to take the
exam for a certificate of competency if working on a full-time basis
after original application for the training certificate. For the
purposes of this section, "full-time basis" means two thousand hours
per year.
NEW SECTION. Sec. 10
Type of Certificate | Substitution for Work Experience | |
(a) | HVAC/R Mechanic I | Up to 1,000 hours of technical college program may be substituted for up to 1,000 hours of work experience. |
(b) | HVAC/R Mechanic II | Up to 2,000 hours of technical college program may be substituted for up to 2,000 hours of work experience, so long as the applicant obtains the additional 2,000 hours of work experience prior to beginning, or after completing, the technical school program. |
(c) | HVAC/R Mechanic III | Up to 4,000 hours of technical college program may be substituted for up to 4,000 hours of work experience, so long as the applicant obtains the additional 4,000 hours of work experience prior to beginning, or after completing, the technical school program. |
NEW SECTION. Sec. 11
(2) The department, with advice from the board, may enter into a
contract with a professional testing agency to develop, administer, and
score HVAC/R mechanic certification and specialty examinations. The
department may set the examination fee by contract with the
professional testing agency.
(3) The department must, at least four times annually, administer
the examination to persons eligible to take it under section 9 of this
act. The examination fee the department charges must cover, but not
exceed, the costs of preparing and administering the examination.
(4) The department must certify the results of the examination upon
the terms and after such a period of time as the department, with the
advice of the board, deems necessary and proper.
(5) The examinations shall be constructed to determine:
(a) Whether the applicant possesses general knowledge of the
technical information and practical procedures that are identified with
the relevant scope of work; and
(b) Whether the applicant is familiar with the applicable
mechanical codes and administrative rules of the department pertaining
to the relevant scope of work.
(6) A person may take the examination as many times as necessary
without limit. All applicants must, before taking the examination, pay
the required examination fee to the agency administering the
examination.
(7) The department, with the advice of the board, shall adopt
policies and procedures to make examinations available in alternative
languages or formats to accommodate all applicants who qualify under
this chapter.
NEW SECTION. Sec. 12
(a) HVAC/R work performed with a general or specialty HVAC/R
contractor registered or licensed under chapter 18.27 or 19.28 RCW, or
a person regularly employed by a public entity or an exempt entity
under chapter 19.28 or 18.27 RCW;
(b) HVAC/R work with a registered general or specialty HVAC/R
contractor, or the equivalent, which was accrued in another state or
country;
(c) HVAC/R work experience in the United States armed forces; or
(d) Any combination of at least two thousand hours of HVAC/R work
experience as described in (a) through (c) of this subsection.
(2) Effective April 1, 2008, a person may apply for an HVAC/R
mechanic II certificate of competency without examination, so long as
the applicant provides the department with evidence of at least four
thousand hours of HVAC/R work experience performed after January 1,
1996. Four thousand hours of this work experience must be:
(a) HVAC/R work with a general or specialty HVAC/R contractor
registered or licensed under chapter 18.27 or 19.28 RCW, or person
regularly employed by a public entity or an exempt entity under chapter
19.28 or 18.27 RCW;
(b) HVAC/R work with a general or specialty HVAC/R contractor, or
the equivalent, which was accrued in another state or country;
(c) HVAC/R work experience in the United States armed forces; or
(d) Any combination of at least four thousand hours of HVAC/R work
experience as described in (a) through (c) of this subsection.
(3) Effective April 1, 2008, a person may apply for an HVAC/R
mechanic III certificate of competency without examination, so long as
the applicant provides the department with evidence of at least eight
thousand hours of HVAC/R work experience performed after January 1,
1996. Eight thousand hours of this work experience must be:
(a) HVAC/R work with a general or specialty HVAC/R contractor
registered or licensed under chapter 18.27 or 19.28 RCW or a person
regularly employed by a public entity or an exempt entity under chapter
19.28 or 18.27 RCW;
(b) HVAC/R work with a general or specialty HVAC/R contractor, or
the equivalent, which was accrued in another state, country, or
province;
(c) HVAC/R work experience in the United States armed forces; or
(d) Any combination of at least eight thousand hours of HVAC/R work
experience as described in (a) through (c) of this subsection.
(4) The department may not accept applications for certification
without examination submitted on or after December 31, 2008. The
department may not extend this deadline.
(5) Effective April 1, 2008, a person may apply for an HVAC/R
mechanic III certificate of competency without examination, so long as
the applicant provides the department with evidence that he or she has
completed an apprenticeship program under chapter 49.04 RCW or an
equivalent apprenticeship program from another state or country.
(6) Notwithstanding subsection (7) of this section, any person
holding a current journey refrigeration mechanic license issued by the
city of Seattle shall be issued a refrigeration and an air conditioning
and heating mechanic III certificate without meeting any additional
requirements.
(7) The department shall include the hours a building or stationary
operating engineer that does not currently hold a journey refrigeration
mechanic license issued by the city of Seattle or another local
jurisdiction has logged up to the maximum required for an HVAC/R
mechanic III certification provided the engineer submits an affidavit
of experience. If the engineer has the requisite number of hours for
a refrigeration and an air conditioning and heating mechanic III
certification, the department shall grant that certification without
prior examination. If the engineer does not have the requisite number
of hours for an HVAC/R mechanic II certification, he or she must obtain
a trainee card and accrue the remaining hours under the supervision of
an HVAC/R mechanic III. Once the engineer has accrued the requisite
number of hours, he or she may take the examination at the appropriate
level as determined by rule.
(8) Effective April 1, 2008, a person may apply for certification
as a gas piping mechanic without examination, so long as he or she
provides the department with evidence that he or she:
(a) Performed at least one thousand hours of gas piping work on or
after January 1, 1996; or
(b) Was licensed as a gas piping fitter, installer, or mechanic by
Kennewick, Seattle, Spokane, Tacoma, Vancouver, or Yakima on July 1,
2007.
NEW SECTION. Sec. 13
(2) The scope of work for this certification includes preventive
maintenance such as filter changing, belt replacement, bearing
lubrication, and equipment logging. A person holding this
certification may not perform major repairs, sealed system work, or
equipment replacement.
(3) A person who installs, alters, or repairs an HVAC/R system
containing six pounds or less of any refrigerant and actuated by a
motor or engine having a standard rating of one-quarter horsepower or
less, or an absorption system having a rating of one-quarter ton of
refrigeration effect is exempt from having to obtain a certificate
under this section.
(4) Any person holding a valid refrigeration operating engineer
license issued by the city of Seattle shall be issued an HVAC/R
operator certificate without meeting any additional requirements. For
purposes of this section, "refrigeration operating engineer" means a
full-time employee who spends a substantial portion of time in the
maintenance and operation of a refrigeration system in a building, or
portion thereof, used for occupant comfort, manufacturing, processing,
or storage of materials or products including, among others, chemicals,
food, candy, and ice cream factories, ice-making plants, meat packing
plants, refineries, perishable food warehouses, hotels, hospitals,
restaurants, and similar occupancies and equipped with a refrigeration
system and whose duty it is to operate, maintain, and keep safe and in
serviceable condition all of the employer's refrigeration systems and
equipment.
(5) The department shall develop an examination that the applicant
must pass before a person can be issued a certificate under this
section. The exam shall be comparable to the current refrigeration
operating engineer license test used by the city of Seattle.
(6) The hours logged as an HVAC/R operator under this section count
towards the hours required to obtain an HVAC/R mechanic I certificate
as long as the operator is supervised during those hours by a certified
HVAC/R mechanic I, II, or III, and holds a current trainee card.
NEW SECTION. Sec. 14
(2) The department shall renew a certificate of competency issued
to a mechanic who applies for renewal not more than ninety days after
the certificate expires, and has complied with the continuing education
requirement in section 16 of this act. The department may not renew a
certificate that has been revoked or suspended. The department may
deny renewal of a certificate if the applicant for renewal owes
outstanding penalties for a final judgment under this chapter.
(3) A certificate of competency is valid for three years, unless
revoked or suspended, and expires on the mechanic's birth date. The
certificate shall include the expiration date.
(4) The department shall create a single document and establish a
single expiration date for a mechanic who holds two or more
certificates or specialties under chapters 18.106 and 19.28 RCW and
this chapter. The document shall list all of the mechanic's
certificates of competency and specialties.
NEW SECTION. Sec. 15
(2) The department shall renew a training certificate issued to a
trainee who provides the department with an accurate list of the
trainee's employers in the HVAC/R industry for the previous two-year
period and the number of hours worked for each employer, and has
complied with the continuing education requirement in section 16 of
this act.
(3) A trainee shall have his or her training certificate in his or
her possession when performing HVAC/R mechanic or operator work. The
trainee shall show the certificate to an authorized representative of
the department at the representative's request.
(4) A training certificate is valid for two years, and expires on
the trainee's birth date. The certificate shall include the expiration
date.
NEW SECTION. Sec. 16
(2) A trainee must demonstrate satisfactory completion of sixty
hours of related supplemental instruction or equivalent training
courses or courses taken as part of an apprenticeship program approved
under chapter 49.04 RCW prior to renewing his or her certificate.
(3) The department, with the advice of the board, shall determine
the contents of continuing education courses and establish the
requirements for satisfactory completion of such courses. If the
department determines that a continuing education course offered in
another state is comparable to courses offered in Washington, the
department shall accept proof of satisfactory completion of the course
as meeting the continuing education requirement in this section.
NEW SECTION. Sec. 17
Trainee is working as a -- | Mechanic must be minimally certified as a -- | Ratio requirement for trainees not in a technical college program | Ratio requirement for trainees in a technical college program | |
(a) | HVAC/R mechanic I | HVAC/R mechanic I, II, or III | 2 trainees to 1 mechanic | 4 trainees to 1 mechanic |
(b) | HVAC/R mechanic II | HVAC/R mechanic II or III | 2 trainees to 1 mechanic | 4 trainees to 1 mechanic |
(c) | HVAC/R mechanic III | HVAC/R mechanic III | 2 trainees to 1 mechanic | 4 trainees to 1 mechanic |
NEW SECTION. Sec. 18
(b) In order for hours to count toward all electrical and HVAC/R
mechanic certifications, the contractor must be licensed as an
electrical contractor under chapter 19.28 RCW and as an HVAC/R
contractor under this chapter.
(c) In order to count hours for an HVAC/R certificate or specialty,
the trainee must be supervised by a certified HVAC/R mechanic. The
mechanic may be employed by a contractor registered or licensed under
chapter 18.27 or 19.28 RCW, provided the contractor also registers
under this chapter.
(d) Notwithstanding (c) of this subsection, a trainee regularly
employed by a public entity, a property management company, or an
exempt entity under chapter 18.27 or 19.28 RCW may count hours for an
HVAC/R certificate or specialty if the trainee is supervised by a
certified HVAC/R mechanic.
(e) In order for hours to count for HVAC/R electrical work under
chapter 19.28 RCW, the trainee must be supervised by an appropriately
certified electrician. The electrician must be employed by a
contractor licensed under chapter 19.28 RCW or a person regularly
employed by a public entity or an exempt entity under chapter 18.27 or
19.28 RCW. Experience towards an HVAC/R mechanic certificate may be
obtained at the same time the trainee is meeting the experience
required by RCW 19.28.191.
(f) Each contractor shall also report to the department the names
and certificate numbers of supervising mechanics.
(2) The department may audit the records of a contractor who
reported hours worked by a trainee under subsection (1) of this section
in the following circumstances: (a) Excessive hours were reported; (b)
hours were reported outside the normal course of the contractor's
business; (c) the type of hours reported do not reasonably match the
type of permits purchased; or (d) for other similar circumstances in
which the department demonstrates a likelihood of excessive hours being
reported. The department shall limit the audit to records necessary to
verify hours.
(3) Information obtained from a contractor under this section is
confidential and is not open to public inspection under chapter 42.56
RCW.
NEW SECTION. Sec. 19
(2) The department may not issue a temporary permit to any
applicant who is not eligible to take the examination for a certificate
of competency or failed the examination for the certificate.
(3) A mechanic with a temporary permit who fails the examination
for a certificate of competency is entitled to continue to perform
HVAC/R work under the temporary permit for ninety days if the mechanic
is enrolled in a department-approved mechanic refresher course. After
completing the mechanic refresher course, the mechanic may retake the
examination.
NEW SECTION. Sec. 20
NEW SECTION. Sec. 21
(2) The department shall immediately suspend the certificate of a
person who has been certified pursuant to RCW 74.20A.320 by the
department of social and health services as a person who is not in
compliance with a support order. If the person has continued to meet
all other requirements for reinstatement during the suspension,
reissuance of the certificate shall be automatic upon the department's
receipt of a release issued by the department of social and health
services stating that the person is in compliance with the order.
NEW SECTION. Sec. 22
(a) A person cleaning or replacing air filters, lubricating
bearings, replacing fan belts, cleaning evaporators or condensers, or
cleaning cooling towers;
(b) A person installing, altering, or repairing an HVAC/R system
containing six pounds or less of any refrigerant and actuated by a
motor or engine having a standard rating of one-quarter horsepower or
less, or absorption system having a rating of one-quarter ton or less
refrigeration effect;
(c) A person installing a wood, pellet, or gas-fueled hearth
appliance that has a visual presence in the living space of a home,
including connecting the appliance with an approved flexible gas supply
line not to exceed forty-eight inches in length and not to include
installation of ventilation duct work or other duct work;
(d) A person setting oil tanks and piping to the furnace;
(e) A person setting propane tanks and piping outside a building;
(f) A person performing HVAC/R work at his or her residence, farm,
place of business, or on other property owned by him or her unless the
HVAC/R work is on the construction of a new building intended for rent,
sale, or lease;
(g) A person performing HVAC/R work on his or her own property or
to regularly employed employees working on the premises of their
employer, unless the HVAC/R work is on the construction of a new
building intended for rent, sale, or lease;
(h) A person performing work for or on behalf of a natural gas
utility, including the installation, repair, and maintenance of gas
piping when such work is incidental to the business of delivering
natural gas to the premises. For the purposes of this chapter,
"natural gas utility" means a gas company, as defined under RCW
80.04.010;
(i) An architect licensed under chapter 18.08 RCW or an engineer
licensed under chapter 18.43 RCW who is designing HVAC/R systems, but
who is not otherwise performing HVAC/R work;
(j) A person making a like-in-kind replacement of a household
appliance; or
(k) A person installing wood or pellet stoves.
(2) Nothing precludes any person who is exempt from the
certification requirements of this chapter under this section from
obtaining a mechanic certificate of competency if they otherwise meet
the requirements of this chapter.
NEW SECTION. Sec. 23
NEW SECTION. Sec. 24
NEW SECTION. Sec. 25
(2) The fees collected under this chapter shall cover the full
costs of issuing contractor registrations under this chapter, the
certificates and permits, devising and administering the examinations,
and administering and enforcing this chapter and chapter 18.106 RCW.
NEW SECTION. Sec. 26
Sec. 27 RCW 18.106.125 and 1983 c 124 s 17 are each amended to
read as follows:
The department shall charge fees for issuance, renewal, and
reinstatement of all certificates and permits and for examinations
required by this chapter. The department shall set the fees by rule.
The fees collected under this act and this chapter shall cover the
full cost of issuing the certificates and permits, devising and
administering the examinations, and administering and enforcing this
chapter and this act. The costs shall include travel, per diem, and
administrative support costs.
Sec. 28 RCW 43.84.092 and 2006 c 337 s 11, 2006 c 311 s 23, 2006
c 171 s 10, 2006 c 56 s 10, and 2006 c 6 s 8 are each reenacted and
amended to read as follows:
(1) All earnings of investments of surplus balances in the state
treasury shall be deposited to the treasury income account, which
account is hereby established in the state treasury.
(2) The treasury income account shall be utilized to pay or receive
funds associated with federal programs as required by the federal cash
management improvement act of 1990. The treasury income account is
subject in all respects to chapter 43.88 RCW, but no appropriation is
required for refunds or allocations of interest earnings required by
the cash management improvement act. Refunds of interest to the
federal treasury required under the cash management improvement act
fall under RCW 43.88.180 and shall not require appropriation. The
office of financial management shall determine the amounts due to or
from the federal government pursuant to the cash management improvement
act. The office of financial management may direct transfers of funds
between accounts as deemed necessary to implement the provisions of the
cash management improvement act, and this subsection. Refunds or
allocations shall occur prior to the distributions of earnings set
forth in subsection (4) of this section.
(3) Except for the provisions of RCW 43.84.160, the treasury income
account may be utilized for the payment of purchased banking services
on behalf of treasury funds including, but not limited to, depository,
safekeeping, and disbursement functions for the state treasury and
affected state agencies. The treasury income account is subject in all
respects to chapter 43.88 RCW, but no appropriation is required for
payments to financial institutions. Payments shall occur prior to
distribution of earnings set forth in subsection (4) of this section.
(4) Monthly, the state treasurer shall distribute the earnings
credited to the treasury income account. The state treasurer shall
credit the general fund with all the earnings credited to the treasury
income account except:
(a) The following accounts and funds shall receive their
proportionate share of earnings based upon each account's and fund's
average daily balance for the period: The capitol building
construction account, the Cedar River channel construction and
operation account, the Central Washington University capital projects
account, the charitable, educational, penal and reformatory
institutions account, the Columbia river basin water supply development
account, the common school construction fund, the county criminal
justice assistance account, the county sales and use tax equalization
account, the data processing building construction account, the
deferred compensation administrative account, the deferred compensation
principal account, the department of retirement systems expense
account, the developmental disabilities community trust account, the
drinking water assistance account, the drinking water assistance
administrative account, the drinking water assistance repayment
account, the Eastern Washington University capital projects account,
the education construction fund, the education legacy trust account,
the election account, the emergency reserve fund, the energy freedom
account, The Evergreen State College capital projects account, the
federal forest revolving account, the freight mobility investment
account, the freight mobility multimodal account, the health services
account, the public health services account, the health system capacity
account, the personal health services account, the state higher
education construction account, the higher education construction
account, the highway infrastructure account, the high-occupancy toll
lanes operations account, the plumbing and HVAC/R certificate fund, the
industrial insurance premium refund account, the judges' retirement
account, the judicial retirement administrative account, the judicial
retirement principal account, the local leasehold excise tax account,
the local real estate excise tax account, the local sales and use tax
account, the medical aid account, the mobile home park relocation fund,
the multimodal transportation account, the municipal criminal justice
assistance account, the municipal sales and use tax equalization
account, the natural resources deposit account, the oyster reserve land
account, the pension funding stabilization account, the perpetual
surveillance and maintenance account, the public employees' retirement
system plan 1 account, the public employees' retirement system combined
plan 2 and plan 3 account, the public facilities construction loan
revolving account beginning July 1, 2004, the public health
supplemental account, the public works assistance account, the Puyallup
tribal settlement account, the real estate appraiser commission
account, the regional mobility grant program account, the resource
management cost account, the rural Washington loan fund, the site
closure account, the small city pavement and sidewalk account, the
special wildlife account, the state employees' insurance account, the
state employees' insurance reserve account, the state investment board
expense account, the state investment board commingled trust fund
accounts, the supplemental pension account, the Tacoma Narrows toll
bridge account, the teachers' retirement system plan 1 account, the
teachers' retirement system combined plan 2 and plan 3 account, the
tobacco prevention and control account, the tobacco settlement account,
the transportation infrastructure account, the transportation
partnership account, the tuition recovery trust fund, the University of
Washington bond retirement fund, the University of Washington building
account, the volunteer fire fighters' and reserve officers' relief and
pension principal fund, the volunteer fire fighters' and reserve
officers' administrative fund, the Washington fruit express account,
the Washington judicial retirement system account, the Washington law
enforcement officers' and fire fighters' system plan 1 retirement
account, the Washington law enforcement officers' and fire fighters'
system plan 2 retirement account, the Washington public safety
employees' plan 2 retirement account, the Washington school employees'
retirement system combined plan 2 and 3 account, the Washington state
health insurance pool account, the Washington state patrol retirement
account, the Washington State University building account, the
Washington State University bond retirement fund, the water pollution
control revolving fund, and the Western Washington University capital
projects account. Earnings derived from investing balances of the
agricultural permanent fund, the normal school permanent fund, the
permanent common school fund, the scientific permanent fund, and the
state university permanent fund shall be allocated to their respective
beneficiary accounts. All earnings to be distributed under this
subsection (4)(a) shall first be reduced by the allocation to the state
treasurer's service fund pursuant to RCW 43.08.190.
(b) The following accounts and funds shall receive eighty percent
of their proportionate share of earnings based upon each account's or
fund's average daily balance for the period: The aeronautics account,
the aircraft search and rescue account, the county arterial
preservation account, the department of licensing services account, the
essential rail assistance account, the ferry bond retirement fund, the
grade crossing protective fund, the high capacity transportation
account, the highway bond retirement fund, the highway safety account,
the motor vehicle fund, the motorcycle safety education account, the
pilotage account, the public transportation systems account, the Puget
Sound capital construction account, the Puget Sound ferry operations
account, the recreational vehicle account, the rural arterial trust
account, the safety and education account, the special category C
account, the state patrol highway account, the transportation 2003
account (nickel account), the transportation equipment fund, the
transportation fund, the transportation improvement account, the
transportation improvement board bond retirement account, and the urban
arterial trust account.
(5) In conformance with Article II, section 37 of the state
Constitution, no treasury accounts or funds shall be allocated earnings
without the specific affirmative directive of this section.
NEW SECTION. Sec. 29
(2) The state of Washington, and its officers, agents, and
employees may not be held liable for any acts performed pursuant to
this chapter.
NEW SECTION. Sec. 30
(2) The board shall consist of thirteen members to be appointed by
the governor with the advice of the director.
(a) Four members shall be HVAC/R mechanics, of which at least one,
but not more than two, shall be an HVAC/R mechanic performing work east
of the crest of the Cascade mountains.
(b) Four members shall be HVAC/R contractors, of which at least
one, but not more than two, shall be a contractor doing business east
of the crest of the Cascade mountains.
(c) One member shall be from the general public and be familiar
with HVAC/R work.
(d) One member shall be a building operator representing the
commercial property management industry.
(e) One member shall be from the stationary operating engineers.
(f) One member shall be from a technical college or an approved
apprenticeship training program.
(g) One member shall be a building official familiar with
enforcement of HVAC/R work.
(3) Except as provided in this subsection, the term of each member
shall be three years. The term of each initial member shall expire as
follows: (a) The terms of the first HVAC/R mechanic and the first
HVAC/R contractor shall expire July 1, 2008; (b) the terms of the
second HVAC/R mechanic, the second HVAC/R contractor, and the public
member shall expire July 1, 2009; and (c) the terms of the third HVAC/R
mechanic and the third HVAC/R contractor shall expire July 1, 2010. To
ensure that the board may continue to act, a member whose term expires
shall continue to serve until his or her replacement is appointed. In
the case of any vacancy on the board for any reason, the governor shall
appoint a new member to serve out the term of the person whose position
has become vacant.
(4) The board shall, at its first meeting, elect one of its members
to serve as chair.
(5) The board shall meet at least quarterly in accordance with a
schedule established by the board.
(6) The board shall:
(a) Conduct proceedings for denying applications, suspending or
revoking certificates, and imposing civil penalties or other remedies.
Such proceedings shall be conducted in accordance with chapter 34.05
RCW;
(b) Review and make recommendations to adopt, amend, or repeal any
rules under this chapter. The director may not adopt, amend, or repeal
any rules until the board has conducted its review and made its
recommendations;
(c) Approve expenditures from the plumbing and HVAC/R certificate
fund; and
(d) Advise the department on all other matters relative to this
chapter.
(7) The members of the board are entitled to be reimbursed for
travel expenses in accordance with RCW 43.03.050 and 43.03.060.
NEW SECTION. Sec. 31
NEW SECTION. Sec. 32
(2) The department shall administer this chapter in conjunction
with its administration of chapter 18.106 RCW.
(3) In the administration of this chapter, the department shall not
enter any controversy arising over work assignments with respect to the
trades involved in the construction industry.
NEW SECTION. Sec. 33
(2) Nothing in this chapter prohibits or restricts an individual
who is certified under chapter 18.106 or 19.28 RCW from engaging in the
trade in which he or she is certified.
(3) Nothing in this chapter shall be construed to regulate plumbing
work defined in chapter 18.106 RCW and applicable rules or electrical
work defined in chapter 19.28 RCW and applicable rules in the scope of
work defined in this chapter.
Sec. 34 RCW 18.27.060 and 2006 c 185 s 14 are each amended to
read as follows:
(2) If the department approves an application, it shall issue a
certificate of registration to the applicant.
(3) If a contractor's surety bond or other security has an
unsatisfied judgment against it or is canceled, or if the contractor's
insurance policy is canceled, the contractor's registration shall be
automatically suspended on the effective date of the impairment or
cancellation. The department shall mail notice of the suspension to
the contractor's address on the certificate of registration by
certified and by first class mail within two days after suspension.
(4) Renewal of registration is valid on the date the department
receives the required fee and proof of bond and liability insurance, if
sent by certified mail or other means requiring proof of delivery. The
receipt or proof of delivery shall serve as the contractor's proof of
renewed registration until he or she receives verification from the
department.
(5) The department shall immediately suspend the certificate of
registration of a contractor who has been certified by the department
of social and health services as a person who is not in compliance with
a support order or a visitation order as provided in RCW 74.20A.320.
The certificate of registration shall not be reissued or renewed unless
the person provides to the department a release from the department of
social and health services stating that he or she is in compliance with
the order and the person has continued to meet all other requirements
for certification during the suspension.
(6) For a contractor who employs plumbers, as described in RCW
18.106.010(10)(c), and is also required to be licensed as an electrical
contractor as required in RCW 19.28.041, while doing pump and
irrigation or domestic pump work described in rule as authorized by RCW
19.28.251, the department shall establish a single
registration/licensing document for those who qualify for both general
contractor registration as defined by this chapter and an electrical
contractor license as defined by chapter 19.28 RCW.
(7) For a contractor who qualifies for two or more registrations or
licenses under this chapter, chapter 18.-- (sections 1 through 26, 29
through 33, and 35 through 39 of this act), and 19.28 RCW, the
department shall establish a single registration/licensing document.
The document shall list all of the contractor's registrations and
licenses.
NEW SECTION. Sec. 35
(2) If the employee of an unregistered contractor is cited by a
compliance inspector, that employee is cited as the agent of the
employer, and issuance of the infraction to the employee is notice to
the unregistered employer contractor that the contractor is in
violation of this chapter. An employee who is cited by a compliance
inspector shall not be liable for any of the alleged violations
contained in the citation unless the employee is also the unregistered
contractor or the employee is performing work that requires a
certification under this chapter without proper proof of the
certification.
NEW SECTION. Sec. 36
NEW SECTION. Sec. 37
(1) A statement that the notice represents a determination that the
infraction has been committed by the contractor or the individual named
in the notice and that the determination shall be final unless
contested as provided in this chapter;
(2) A statement that the infraction is a noncriminal offense for
which imprisonment shall not be imposed as a sanction;
(3) A statement of the violation that necessitated issuance of the
infraction;
(4) A statement of penalty involved if the infraction is
established;
(5) A statement of the options provided in this chapter for
responding to the notice and the procedures necessary to exercise these
options;
(6) A statement that at any hearing to contest the notice of
infraction the state has the burden of proving, by a preponderance of
the evidence, that the infraction was committed; and that the
contractor or individual may subpoena witnesses, including the
compliance inspector of the department who issued and served the notice
of infraction;
(7) A statement that at any hearing to contest the notice of
infraction against an unregistered contractor, the uncertified
individual has the burden of proving that the infraction did not occur;
(8) A statement that the contractor or individual must respond to
the notice of infraction in one of the ways provided in this chapter;
and
(9) A statement that a contractor or individual failure to timely
select one of the options for responding to the notice of infraction
after receiving a statement of the options provided in this chapter for
responding to the notice of infraction and the procedures necessary to
exercise these options is guilty of a gross misdemeanor and may be
punished by a fine or imprisonment in jail.
NEW SECTION. Sec. 38
NEW SECTION. Sec. 39
(2) If the contractor or individual named in the notice of
infraction does not elect to contest the notice of infraction, then the
contractor or individual shall pay to the department, by check or money
order, the amount of the penalty prescribed for the infraction. When
a response that does not contest the notice of infraction is received
by the department with the appropriate penalty, the department shall
make the appropriate entry in its records.
(3) If the contractor or individual named in the notice of
infraction elects to contest the notice of infraction, the contractor
or individual shall respond by filing with the department specifying
the appeal to the department in the manner specified in this chapter.
(4) If any contractor or individual issued a notice of infraction
fails to respond within the prescribed response period, the contractor
or individual shall be guilty of a misdemeanor and prosecuted in the
county where the infraction occurred.
(5) After final determination by an administrative law judge that
an infraction has been committed, a contractor or individual who fails
to pay a monetary penalty within thirty days, that is not waived
pursuant to this chapter, and who fails to file an appeal, shall be
guilty of a misdemeanor and be prosecuted in the county where the
infraction occurred.
(6) A contractor or individual who fails to pay a monetary penalty
within thirty days after exhausting appellate remedies shall be guilty
of a misdemeanor and be prosecuted in the county where the infraction
occurred.
(7) If a contractor or individual who is issued a notice of
infraction is a contractor or individual who has failed to register or
be certified as a contractor or individual under this chapter, the
contractor or individual is subject to a monetary penalty per
infraction as provided in the schedule of penalties established by the
department, and each day the person works without becoming registered
or certified is a separate infraction.
Sec. 40 RCW 18.106.130 and 1973 1st ex.s. c 175 s 13 are each
amended to read as follows:
All moneys received from certificates, permits, or other sources,
shall be paid to the state treasurer as ex officio custodian thereof
and by him placed in a special fund designated as the "plumbing and
HVAC/R certificate fund". He shall pay out upon vouchers duly and
regularly issued therefor and approved by the director. The treasurer
shall keep an accurate record of payments into said fund, and of all
disbursement therefrom. Said fund shall be charged with its pro rata
share of the cost of administering said fund.
NEW SECTION. Sec. 41
NEW SECTION. Sec. 42
NEW SECTION. Sec. 43
NEW SECTION. Sec. 44
NEW SECTION. Sec. 45 Section 12 of this act expires January 1,
2009."
SHB 1876 -
By Senator
On page 1, line 2 of the title, after "work;" strike the remainder of the title and insert "amending RCW 18.106.125, 18.27.060, and 18.106.130; reenacting and amending RCW 43.84.092; adding a new chapter to Title 18 RCW; creating a new section; prescribing penalties; providing effective dates; and providing an expiration date."