PERMANENT RULES
CLEAN AIR AGENCY
Purpose: To improve the classification of air contaminant sources and to clarify reporting requirements.
Citation of Existing Rules Affected by this Order: Repealing Section 5.02 of Regulation I; and amending Sections 5.03, 5.05, and 5.07 of Regulation I.
Statutory Authority for Adoption: Chapter 70.94 RCW.
Adopted under notice filed as WSR 04-11-122 on May 19, 2004.
Number of Sections Adopted in Order to Comply with Federal Statute: New 0, Amended 0, Repealed 0; Federal Rules or Standards: New 0, Amended 0, Repealed 0; or Recently Enacted State Statutes: New 0, Amended 0, Repealed 0.
Number of Sections Adopted at Request of a Nongovernmental Entity: New 0, Amended 0, Repealed 0.
Number of Sections Adopted on the Agency's Own Initiative: New 0, Amended 0, Repealed 0.
Number of Sections Adopted in Order to Clarify, Streamline, or Reform Agency Procedures: New 0, Amended 0, Repealed 0.
Number of Sections Adopted Using Negotiated Rule Making: New 0, Amended 0, Repealed 0; Pilot Rule Making: New 0, Amended 0, Repealed 0; or Other Alternative Rule Making: New 0, Amended 0, Repealed 0.
Date Adopted: June 24, 2004.
Gerald Pade
Engineer
REPEALER
REGULATION I SECTION 5.02 APPLICABILITY AND PURPOSE OF THE
REGISTRATION PROGRAM
AMENDATORY SECTION
REGULATION I SECTION 5.03 APPLICABILITY OF REGISTRATION
PROGRAM ((REQUIRED))
(a) The requirements of this article shall apply only to:
(1) Sources subject to a federal emission standard under:
(A) 40 CFR Part 60 (except Subparts B, S, BB, and AAA);
(B) 40 CFR Part 61 (except Subparts B, H, I, K, Q, R, T, W, and the provisions of Subpart M pertaining to asbestos on roadways, asbestos demolition and renovation activities, and asbestos spraying);
(C) 40 CFR Part 62; or
(D) 40 CFR Part 63 (except Subpart LL and the provisions of Subparts S and MM pertaining to kraft and sulfite pulp mills);
(2) Sources with a federally enforceable emission limitation established in order to avoid operating permit program applicability under Article 7 of this regulation;
(3) Sources with annual emissions:
(A) Greater than or equal to 2.50 tons of any single hazardous air pollutant (HAP);
(B) Greater than or equal to 6.25 tons of total hazardous air pollutants (HAP); or
(C) Greater than or equal to 25.0 tons of carbon monoxide (CO), nitrogen oxides (NOx), particulate matter (PM2.5 or PM10), sulfur oxides (SOx), or volatile organic compounds (VOC);
(4) Sources subject to the following sections of Regulation I, II, or III:
(A) Refuse burning equipment subject to Section 9.05 of Regulation I (including crematories);
(B) Fuel burning equipment or refuse burning equipment burning oil that exceeds any limit in Section 9.08 of Regulation I and sources marketing oil to such sources;
(C) Fuel burning equipment subject to Section 9.09 of Regulation I with a rated heat input greater than or equal to 1 MMBtu/hr of any fuel other than natural gas, propane, butane, or distillate oil, or greater than or equal to 10 MMBtu/hr of any fuel;
(D) Sources with spray-coating operations subject to Section 9.16 of Regulation I;
(E) Petroleum refineries subject to Section 2.03 of Regulation II;
(F) Gasoline loading terminals subject to Section 2.05 of Regulation II;
(G) Gasoline dispensing facilities subject to Section 2.07 of Regulation II;
(H) Volatile organic compound storage tanks subject to Section 3.02 of Regulation II;
(I) Can and paper coating facilities subject to Section 3.03 of Regulation II;
(J) Motor vehicle and mobile equipment coating operations subject to Section 3.04 of Regulation II;
(K) Flexographic and rotogravure printing facilities subject to Section 3.05 of Regulation II;
(L) Polyester, vinylester, gelcoat, and resin operations subject to Section 3.08 of Regulation II;
(M) Aerospace component coating operations subject to Section 3.09 of Regulation II;
(N) Coatings and ink manufacturing subject to Section 3.11 of Regulation II;
(O) Dry cleaners subject to Section 3.03 of Regulation III;
(P) Solvent metal cleaners subject to Section 3.05 of Regulation III; or
(Q) Ethylene oxide sterilizers subject to Section 3.07 of Regulation III;
(5) Sources with any of the following gas or odor control equipment having a rated capacity of greater than or equal to 200 cfm (≥4" diameter inlet):
(A) Activated carbon adsorption;
(B) Afterburner;
(C) Barometric condenser;
(D) Biofilter;
(E) Catalytic afterburner;
(F) Catalytic oxidizer;
(G) Chemical oxidation;
(H) Condenser;
(I) Dry sorbent injection;
(J) Flaring;
(K) Non-selective catalytic reduction;
(L) Refrigerated condenser;
(M) Selective catalytic reduction; or
(N) Wet scrubber;
(6) Sources with any of the following particulate control equipment having a rated capacity of greater than or equal to 2,000 cfm (≥10" diameter inlet):
(A) Baghouse;
(B) Demister;
(C) Electrostatic precipitator;
(D) HEPA (high efficiency particulate air) filter;
(E) HVAF (high velocity air filter);
(F) Mat or panel filter;
(G) Mist eliminator;
(H) Multiple cyclones;
(I) Rotoclone;
(J) Screen;
(K) Venturi scrubber;
(L) Water curtain; or
(M) Wet electrostatic precipitator;
(7) Sources with a single cyclone having a rated capacity of greater than or equal to 20,000 cfm (≥27" diameter inlet);
(8) Sources with any of the following equipment:
(A) Asphalt batch plants;
(B) Burn-off ovens;
(C) Coffee roasters;
(D) Commercial composting with raw materials from off-site;
(E) Commercial smokehouses with odor control equipment;
(F) Concrete batch plants (ready-mix concrete);
(G) Galvanizing;
(H) Iron or steel foundries;
(I) Microchip or printed circuit board manufacturing;
(J) Rendering plants;
(K) Rock crushers or concrete crushers;
(L) Sewage treatment plants with odor control equipment;
(M) Shipyards;
(N) Steel mills; or
(O) Wood preserving lines or retorts; and
(9) Sources with equipment (or control equipment) that has been determined by the Control Officer to warrant registration through review of a Notice of Construction application under Section 6.03(a) or a Notification under Section 6.03(b) of this regulation, due to the amount and nature of air contaminants produced, or the potential to contribute to air pollution, and with special reference to effects on health, economic and social factors, and physical effects on property.
(b) (((a))) The ((registration)) requirements of this
article ((do)) shall not apply to:
(1) ((m))Motor vehicles;
(2) ((n))Nonroad engines or nonroad vehicles as defined
in Section 216 of the federal Clean Air Act;
(3) ((s))Sources that require an operating permit under
Article 7 of this regulation;
(4) ((spray-coating operations exempt under Section
9.16(b) of this regulation)) Solid fuel burning devices
subject to Article 13 of this regulation; or
(5) ((a))Any source, including any listed in Sections
5.03(((b) below)) (a)(4) through 5.03 (a)(9) of this
regulation, that has been determined through review by the
Control Officer not to warrant registration, due to the amount
and nature of air contaminants produced or the potential to
contribute to air pollution, and with special reference to
effects on health, economic and social factors, and physical
effects on property.
(c) (((b))) It shall be unlawful for any person to cause
or allow the operation of any source ((required to register
under Section 5.03)) subject to registration under this
section, unless it ((conforms to)) meets all the requirements
of Article 5 of this regulation. ((Except as provided in
Section 5.03(a), the owner or operator of each of the
following stationary air contaminant sources shall register
the source with the Agency by paying the annual fee required
by Section 5.07 and submitting any reports required by Section
5.05.
(1) Any category of stationary sources to which a federal standard of performance (NSPS) under 40 CFR Part 60, other than Subpart S (Primary Aluminum Reduction Plants), BB (Kraft Pulp Mills), or AAA (New Residential Wood Heaters), applies;
(2) Any source category subject to the National Emission Standards for Hazardous Air Pollutants (NESHAP) under 40 CFR Part 61, other than Subpart M (asbestos on roadways, asbestos demolition or renovation activities, or asbestos spraying), or 40 CFR Part 63;
(3) Any source that emits any of the following pollutants at a rate of emission equal to or greater than any one of the following rates (tons/year):
carbon monoxide . . . . . . . . . . . . | 25 |
nitrogen oxides . . . . . . . . . . . . | 25 |
sulfur dioxide . . . . . . . . . . . . | 25 |
particulate matter (PM10) . . . . . . . . . . . . | 25 |
particulate matter (PM2.5) . . . . . . . . . . . . | 25 |
volatile organic compounds (VOC) . . . . . . . . . . . . | 25 |
facility-combined total of all toxic air contaminants (TAC) . . . . . . . . . . . . | 6 |
any single toxic air contaminant (TAC) . . . . . . . . . . . . | 2 |
(5) Any source that has been determined through review by the Control Officer to warrant registration, due to the amount and nature of air contaminants produced, or the potential to contribute to air pollution, with special reference to effects on health, economic and social factors, and physical effects on property;
(6) Any source that has elected to opt out of the operating permit program by limiting its potential-to-emit (synthetic minor) or is required to report periodically to demonstrate nonapplicability to EPA require-ments under Sections 111 or 112 of the federal Clean Air Act;
(7) Other sources, such as:
aerosol can-filling facilities;
agricultural chemical facilities engaging in the manufacturing of liquid or dry fertilizers or pesticides;
agricultural drying and dehydrating operations;
alumina processing;
ammonium sulfate manufacturing plants;
asphalt and asphalt products production facilities;
automobile or light-duty truck surface coating operations;
baker's yeast manufacturing;
brick and clay manufacturing plants, including tiles and ceramics;
cattle feedlots with operational facilities that have an inventory of 1,000 or more cattle in operation between June 1 and October 1, where vegetation forage growth is not sustained over the majority of the lot during the normal growing season;
chemical manufacturing plants;
coal preparation plants;
coffee roasting facilities;
composting operations, including commercial, industrial and municipal, but exempting agricultural and residential composting activities;
concrete product manufacturers and ready-mix and premix concrete plants;
crematoria or animal carcass incinerators;
dry cleaning plants;
ethylene dichloride, polyvinyl chloride, or vinyl chloride plants;
explosives production;
flexible polyurethane foam production;
flexible vinyl and urethane coating and printing operations;
gasoline stations, bulk gasoline plants, and gasoline loading terminals;
gelcoat, polyester, resin, or vinylester coating manufacturing operations at commercial or industrial facilities;
glass manufacturing plants;
grain, seed, animal feed, legume, and flour processing operations and handling facilities;
hazardous waste treatment and disposal facilities;
ink manufacturers;
insulation fiber manufacturers;
landfills, active and inactive, including covers, gas collection systems, or flares;
lead-acid battery manufacturing plants;
lime manufacturing plants;
metal casting facilities and foundries, ferrous and nonferrous;
metal plating and anodizing operations;
metallic and nonmetallic mineral processing plants, including rock crushing plants and sand and gravel operations;
metallurgical processing plants;
mills such as lumber, plywood, shake, shingle, woodchip, veneer operations, dry kilns, pulpwood insulating board, or any combination thereof;
mineral wool production;
mineralogical processing plants;
municipal waste combustors;
nitric acid plants;
paper manufacturers, except Kraft and sulfite pulp mills;
petroleum refineries;
pharmaceuticals production;
plastics and fiberglass product fabrication facilities;
pneumatic materials conveying operations and industrial house-keeping vacuuming systems that exhaust more than 1,000 acfm to the atmosphere;
portland cement plants;
primary copper smelters, lead smelters, magnesium refining and zinc smelters, but excluding primary aluminum plants;
rendering plants;
semiconductor manufacturing;
shipbuilding and ship repair (surface coating);
soil vapor extraction (active), thermal soil contaminant desorption, or groundwater air stripping remediation projects;
sulfuric acid plants;
surface-coating manufacturers;
surface spray-coating operations, including automotive, metal, cans, pressure-sensitive tape, labels, coils, wood, plastic, rubber, glass, paper, and other substrates;
synthetic fiber production facilities;
synthetic organic chemical manufacturing industries;
tire recapping facilities;
vegetable oil production;
wastewater treatment plants; or
wood treatment.))
(d) An exemption from new source review under Article 6 of this regulation shall not be construed as an exemption from registration under this article. In addition, an exemption from registration under this article shall not be construed as an exemption from any other provision of Regulation I, II, or III.
AMENDATORY SECTION
REGULATION I SECTION 5.05 ((GENERAL REPORTING REQUIREMENTS
FOR)) REGISTRATION REQUIREMENTS
(a) ((General.)) The owner or operator of ((an air
contaminant)) a source ((for which)) requiring registration
((is required by)) under Section 5.03 of this regulation((,))
shall make reports containing information as required by the
Agency concerning location, size, and height of contaminant
outlets, processes employed, nature and quantity of the air
contaminant emission, and such other information as is
relevant to air pollution and available or reasonably capable
of being assembled.
(((b) Registration Form. Registration information shall
be provided on forms supplied by the Agency and shall be
completed and returned within the time specified on the form.
(c) Reporting Responsibility. The owner, operator, or a
designated representative shall sign Agency registration and
reporting forms for each source.)) The owner or operator ((of
the source)) shall be responsible for obtaining the proper
forms from the Agency, notifying the Agency of ((the)) its
existence ((of the source)) (including changes in its
ownership or name), and for the accuracy, completeness, and
timely submittal of all registration reports((ing information
and any accompanying)) and fees.
(((d) Emission Reporting. An emission report shall be
required from the owner or operator of a source requiring
registration, listing those air contaminants emitted during
the previous calendar year that equal or exceed the following
(tons/year):
carbon monoxide (CO) emissions . . . . . . . . . . . . | 25.0 |
facility combined total of all hazardous air pollutant (HAP) emissions . . . . . . . . . . . . | 6.0 |
any single hazardous air pollutant (HAP) emission . . . . . . . . . . . . | 2.0 |
nitrogen oxide (NOx) emissions . . . . . . . . . . . . | 25.0 |
particulate matter (PM10) emissions . . . . . . . . . . . . | 25.0 |
particulate matter (PM2.5) emissions . . . . . . . . . . . . | 25.0 |
sulfur oxide (SOx) emissions . . . . . . . . . . . . | 25.0 |
volatile organic compounds (VOC) emissions . . . . . . . . . . . . | 25.0 |
(b) The owner or operator of a source requiring registration under Section 5.03 of this regulation shall submit a report by June 30th of each year, listing the emissions of those air contaminants emitted during the previous calendar year that equaled or exceeded:
(1) 2.50 tons of any single hazardous air pollutant (HAP);
(2) 6.25 tons of total hazardous air pollutants (HAP); or
(3) 25.0 tons of carbon monoxide (CO), nitrogen oxides (NOx), particulate matter (PM2.5 or PM10), sulfur oxides (SOx), or volatile organic compounds (VOC).
(c) (((e) Operation and Maintenance Plan. Owners or
operators of air contaminant sources subject to Section 5.03
above)) The owner or operator of a registered source shall
develop and implement an operation and maintenance plan to
((assure)) ensure continuous compliance with Regulations I,
II, and III. A copy of the plan shall be filed with the
Control Officer upon request. The plan shall reflect good
industrial practice and shall include, but not be limited to,
the following:
(1) Periodic inspection of all equipment and control equipment;
(2) Monitoring and recording of equipment and control equipment performance;
(3) Prompt repair of any defective equipment or control equipment;
(4) Procedures for start up, shut down, and normal operation;
(5) The control measures to be employed to ((assure))
ensure compliance with Section 9.15 of ((Regulation I)) this
regulation; and
(6) A record of all actions required by the plan.
The plan shall be reviewed by the source owner or operator at least annually and updated to reflect any changes in good industrial practice.
(((f) Removal from Registration Program. Continued
payment of the annual registration fee to the Agency maintains
the registration of the source with the Agency, as well as the
status of the source as an operating facility. The Agency
shall remove a source from the registration program if a
registration fee has not been paid within 90 days of the date
of the original fee invoice, or upon written request from the
owner or operator of the source. It shall be unlawful for any
person to operate a source that has been removed from the
registration program, unless the owner or operator has
submitted and received an approval for a "Notice of
Construction and Application for Approval", in compliance with
Article 6.
(g) Report of Change of Ownership and Fee.
(1) A new owner of a registered source shall report in writing any change of ownership to the Agency within 45 days of such a change, and
(2) Pay a fee of $100.))
AMENDATORY SECTION
REGULATION I SECTION 5.07 ANNUAL REGISTRATION FEES
(a) The Agency shall assess annual fees as set forth in
Section 5.07(c) ((below)) of this regulation for services
provided in administering the registration program. Fees
received under the registration program shall not exceed the
cost of administering the program, which shall be defined as
initial registration and annual or other periodic reports from
the source owner providing information directly related to air
pollution registration, on-site inspections necessary to
verify compliance with registration requirements, data storage
and retrieval systems necessary for support of the
registration program, emission inventory reports and emission
reduction credits computed from information provided by
sources pursuant to registration program requirements, staff
review, including engineering analysis for accuracy and
currentness, of information provided by sources pursuant to
registration program requirements, clerical and other office
support provided in direct furtherance of the registration
program, and administrative support provided in directly
carrying out the registration program. Payment of these fees
by the owner or operator of a source shall maintain its active
registration status (even if it is not actively operating).
((Registration fees do not apply to sources subject to Article
7 of Regulation I.))
(b) Upon assessment by the Agency, registration fees are
due and payable within 45 days of the date of the invoice.
They shall be deemed delinquent if not fully paid within 45
days of the date of the invoice and shall be subject to an
additional delinquent fee equal to 25% of the original fee,
not to exceed $1,000. Persons knowingly under-reporting
emissions or other information used to set fees, or persons
required to pay emission or permit fees who are more than 90
days late with such payments may be subject to a penalty equal
to 3 times the amount of the original fee owed (in addition to
other penalties provided by chapter 70.94 RCW). ((In
accordance with Section 5.05(f), sources that have not paid
their fee within 90 days of the date of the invoice shall be
removed from the registration program.
(c) Annual registration fees are assessed either by the emission reporting thresholds or, if below emission thresholds, by the primary North American Industry Classification System (NAICS) codes (North American Industry Classification System Manual, U.S. Executive Office of the President, Office of Management and Budget, 1997):
(1) Emission reporting sources under Section 5.05(d) that equal or exceed any of the emission thresholds in that paragraph shall be charged an annual registration fee of $1,802.50 plus an additional emission rate fee of:
$23 for each ton of CO reported in the previous calendar year, and
$46 for each ton of NOx reported in the previous calendar year, and
$46 for each ton of PM10 reported in the previous calendar year, and
$46 for each ton of SOx reported in the previous calendar year, and
$46 for each ton of VOC reported in the previous calendar year, and
$46 for each ton of HAP reported in the previous calendar year.
(2) Emission reporting sources under Section 5.05(d) that equal or exceed twice any of the emission thresholds in that paragraph shall be charged the annual registration fee of $3,605 plus an additional emission rate fee of:
$23 for each ton of CO reported in the previous calendar year, and
$46 for each ton of NOx reported in the previous calendar year, and
$46 for each ton of PM10 reported in the previous calendar year, and
$46 for each ton of SOx reported in the previous calendar year, and
$46 for each ton of VOC reported in the previous calendar year, and
$46 for each ton of HAP reported in the previous calendar year.
(3) Automobile body repair and painting (NAICS = 811121) . . . . . . . . . . . . $309
facilities that qualified for the EnviroStar rebate in 2002 . . . . . . . . . . . . $51.50
(4) Perchloroethylene dry-cleaning plants, except rug cleaning (NAICS = 812322) vented . . . . . . . . . . . . $515
unvented . . . . . . . . . . . . $51.50
(5) Gasoline service stations with gasoline annual throughput during the last calendar year (as certified at the time of annual fee payment) of:
(i) more than 6,000,000 gallons . . . . . . . . . . . . subject to
Section 5.07 (c)(1) above
(ii) 3,600,001 to 6,000,000 gallons . . . . . . . . . . . . $1,030
(iii) 1,200,001 to 3,600,000 gallons . . . . . . . . . . . . $618
(iv) 840,001 to 1,200,000 gallons . . . . . . . . . . . . $309
(v) 200,000 to 840,000 gallons . . . . . . . . . . . . $206
(vi) less than 200,000 gallons . . . . . . . . . . . . $103
(6) Except as provided in Section 5.07 (c)(8), sources requiring registration under Section 5.03 in the following NAICS codes, or as subsequently assigned to Section 5.07 (c)(6) by the Control Officer, shall be charged an annual registration fee of $1,648:
NAICS NAICS Description
212312 Crushed and Broken Limestone Mining and Quarrying
212319 Other Crushed and Broken Stone Mining and Quarrying
212321 Construction Sand and Gravel Mining
212322 Industrial Sand Mining
221122 Electric Power Distribution
221320 Sewage Treatment Facilities
234110 Highway and Street Construction
311111 Dog and Cat Food Manufacturing
311119 Other Animal Food Manufacturing
311612 Meat Processed from Carcasses
311613 Rendering and Meat Byproduct Processing
311999 All Other Miscellaneous Food Manufacturing
321114 Wood Preservation
324121 Asphalt Paving Mixture and Block Manufacturing
324122 Asphalt Shingle and Coating Materials Manufacturing
325311 Nitrogenous Fertilizer Manufacturing
325314 Fertilizer (Mixing Only) Manufacturing
325412 Pharmaceutical Preparation Manufacturing
325612 Polish and Other Sanitation Good Manufacturing
325910 Printing Ink Manufacturing
326199 All Other Plastics Product Manufacturing
326291 Rubber Product Manufacturing for Mechanical Use
327211 Flat Glass Manufacturing
327310 Cement Manufacturing
327320 Ready-Mix Concrete Manufacturing
327390 Other Concrete Product Manufacturing
327420 Gypsum Product Manufacturing
327910 Abrasive Product Manufacturing
327992 Ground or Treated Mineral and Earth Manufacturing
327999 All Other Miscellaneous Nonmetallic Mineral Product Manufacturing
331111 Iron and Steel Mills
331222 Steel Wire Drawing
331312 Primary Aluminum Production
331492 Secondary Smelting, Refining, and Alloying of Nonferrous Metal (except Copper and Aluminum)
331511 Iron Foundries
331512 Steel Investment Foundries
331513 Steel Foundries (except Investment)
331524 Aluminum Foundries (except Die-Casting)
331525 Copper Foundries (except Die-Casting)
331528 Other Nonferrous Foundries (except Die-Casting)
332811 Metal Heat Treating
332812 Metal Coating, Engraving (except Jewelry and Silverware), and Allied Services to Manufacturers
332813 Electroplating, Plating, Polishing, Anodizing, and Coloring
333414 Heating Equipment (except Warm Air Furnaces) Manufacturing
333999 All Other Miscellaneous General Purpose Machinery Manufacturing
334412 Bare Printed Circuit Board Manufacturing
334413 Semiconductor and Related Device Manufacturing
334418 Printed Circuit Assembly (Electronic Assembly) Manufacturing
335129 Other Lighting Equipment Manufacturing
335312 Motor and Generator Manufacturing
335911 Storage Battery Manufacturing
336411 Aircraft Manufacturing
336413 Other Aircraft Parts and Auxiliary Equipment Manufacturing
336611 Ship Building and Repairing
422510 Grain and Field Bean Wholesalers
422710 Petroleum Bulk Stations and Terminals
422720 Petroleum and Petroleum Products Wholesalers (except Bulk Stations and Terminals)
481111 Scheduled Passenger Air Transportation
486910 Pipeline Transportation of Refined Petroleum Products
488190 Other Support Activities for Air Transportation
488210 Support Activities for Rail Transportation
488490 Other Support Activities for Road Transportation
562111 Solid Waste Collection
622110 General Medical and Surgical Hospitals
622210 Psychiatric and Substance Abuse Hospitals
622310 Specialty (except Psychiatric and Substance Abuse) Hospitals
812210 Funeral Homes and Funeral Services
812220 Cemeteries and Crematories
813910 Business Associations
922140 Correctional Institutions
(7) Except as provided in Section 5.07 (c)(8), all other sources requiring registration under Section 5.03 and not listed in Sections 5.07 (c)(1) through 5.07 (c)(6) shall be charged an annual registration fee of $824.
(8) All sources required to be registered by Sections 5.07 (c)(6) and 5.07 (c)(7), except sources with equipment subject to Section 6.11 of Regulation I or Section 2.02 of Regulation III, that certify (using the procedures in WAC 296-27-00103: Partial Exemption for Employers With 10 or Fewer Employees) they did not employ more than 10 persons at any time during the previous calendar year, shall be charged an annual registration fee of $412.))
(c) Except as specified in Section 5.07 (d) and (e) of this regulation, registered sources shall be assessed a fee of $850, plus the following fees:
(1) Sources subject to a federal emission standard as specified in Section 5.03 (a)(1) of this regulation shall be assessed $1,750 per subpart of 40 CFR Parts 60-63;
(2) Sources subject to a federally enforceable emission limitation as specified in Section 5.03 (a)(2) or meeting the emission thresholds specified in Section 5.03 (a)(3) of this regulation shall be assessed $2,000; and
(3) Sources subject to the emission reporting requirements under Section 5.05(b) of this regulation shall be assessed $23 for each ton of CO and $46 for each ton of NOx, PM10, SOx, HAP, and VOC, based on the emissions reported during the previous calendar year.
(d) Gasoline dispensing facilities shall be assessed the following fees based on their gasoline throughput during the previous calendar year (as certified at the time of payment):
(1) More than 6,000,000 gallons | $2,000; |
(2) 3,600,001 to 6,000,000 gallons | $1,000; |
(3) 1,200,001 to 3,600,000 gallons | $750; |
(4) 840,001 to 1,200,000 gallons | $500; |
(5) 200,001 to 840,000 gallons | $250. |
(1) Sources with spray-coating operations subject to Section 9.16 of this regulation that use no more than 4,000 gallons per year of total coatings and solvents;
(2) Gasoline dispensing facilities subject to Section 2.07 of Regulation II with gasoline annual throughput during the previous calendar year (as certified at the time of payment) of no more than 200,000 gallons;
(3) Motor vehicle and mobile equipment coating operations subject to Section 3.04 of Regulation II; and
(4) Unvented dry cleaners subject to Section 3.03 of Regulation III.