PROPOSED RULES
Supplemental Notice to WSR 08-03-009.
Exempt from preproposal statement of inquiry under WSR 05-2-097 [05-20-097].
Title of Rule and Other Identifying Information: Achieving desired future conditions in riparian management zones. This rule proposal amends WAC 222-30-021(1) to change timber harvest and leave tree requirements in riparian management zones adjacent to Type S and F Waters as defined in WAC 222-16-030. It pertains to forest lands in western Washington.
Hearing Location(s): Borst Park, Kitchen 1, 902 Johnson Road, Centralia, on Tuesday, September 9, 2008, at 6:00 p.m.; at the Colville Public Library, 195 South Oak, Colville, on Wednesday, September 10, 2008, at 6:00 p.m.; at the Mount Vernon Fire Department Station 2, 1901 North LaVenture Road, Mt. Vernon, on Tuesday, September 16, 2008, at 6:00 p.m.; and at the Port Townsend Fire Station, 1256 Lawrence Street, Port Townsend, on Thursday, September 18, 2008, at 6:00 p.m.
Date of Intended Adoption: November 12, 2008.
Submit Written Comments to: Patricia Anderson, DNR Forest Practices Division, P.O. Box 47012, Olympia, WA 98504-7012, e-mail forest.practicesboard@dnr.wa.gov, fax (360) 902-1428, by September 19, 2008.
Assistance for Persons with Disabilities: Contact forest practices division at (360) 902-1400, by August 29, 2008, TTY (360) 902-1125.
Purpose of the Proposal and Its Anticipated Effects, Including Any Changes in Existing Rules: WAC 222-30-021 provides prescriptions and options to harvesting trees in forested "riparian management zones" as defined in WAC 222-16-010. Pursuant to RCW 76.09.370, the forest practices board incorporates a scientific-based adaptive management process to determine the effectiveness of forest practices rules in aiding Washington's salmon recovery effort. Under this adaptive management process, a scientific study was completed by the forest practices board's cooperative monitoring, evaluation, and research committee. The study, entitled Validation of the Western Washington Riparian Desired Future Condition (DFC) Performance Targets in the Washington State Forest Practices Rules with Data From Mature, Unmanaged, Conifer-Dominated Riparian Stands, found that basal area per acre of mature, unmanaged conifer-dominated riparian stands are greater than the values used in the current rule.
In response to the DFC study findings, the board is considering three alternative rule amendments to WAC 222-30-021(1). The intended effects of all of the alternatives are to increase the basal area retained in riparian management zones, thereby decreasing allowable harvest.
• | The first alternative would increase the target basal area per acre to three three hundred twenty-five square feet for all site classes that a riparian forest stand is projected to reach at one hundred forty years from the year of harvest in the riparian management zone. |
• | The second alternative would increase the target basal area per acre the same as the first alternative, and would also: |
- | allow landowners to credit the required inner zone leave trees towards meeting the riparian zone basal area target; and |
- | expand the table, "Option 2. Leaving trees closest to water," to include site classes IV and V on streams greater than ten feet in width. |
• | The third would increase the target basal area per acre the same as the first alternative, and will allow landowners to credit the required inner zone leave trees towards meeting the riparian zone basal area target. |
Reasons Supporting Proposal: The proposed rule changes are based on recommendations resulting from the scientifically based adaptive management process outlined in WAC 222-12-045. Through this process, the board has determined that the forest practices rules should be adjusted to ensure that appropriate riparian buffers are maintained on forest land covered by the Forest Practices Act.
Statutory Authority for Adoption: RCW 76.09.040 and 76.09.370(6).
Rule is not necessitated by federal law, federal or state court decision.
Name of Proponent: Forest practices board, governmental.
Name of Agency Personnel Responsible for Drafting: Marc Engel, 1111 Washington Street S.E., Olympia, (360) 902-1390; Implementation: Gary Graves, 1111 Washington Street S.E., Olympia, (360) 902-1483; and Enforcement: Lenny Young, 1111 Washington Street S.E., Olympia, (360) 902-1744.
A small business economic impact statement has been prepared under chapter 19.85 RCW.
Prior to rule adoption, the Administrative Procedure Act (APA) (chapter 34.05 RCW)1 requires completion of a cost-benefit analysis (CBA) that demonstrates that probable benefits of the proposal exceed its probable costs and that it is the most cost-effective means of achieving the goal of the rule change. A small business economic impact statement (SBEIS) is required by the Regulatory Fairness Act (RFA) (chapter 19.85 RCW)2 to consider the impacts of state administrative rules on small businesses, defined as those with fifty or fewer employees. An SBEIS compares the costs of compliance for small businesses with the cost of compliance for the 10% of businesses that are the largest businesses required to comply with the proposed rules.
This economic analysis combines the SBEIS and the CBA and complies with the legislative requirements for these analyses as part of the rule-making process.
HISTORICAL CONTEXT: The forests and fish negotiations resulted in rules that manage timber harvests in riparian zones; one of the objectives of which is to reach DFC. The DFC of a riparian forest is a timber stand that demonstrates the characteristics of mature, unmanaged riparian stands at age 1403. One of the metrics chosen to create these characteristics is a target basal area per acre at age 140 (hereinafter referred to as bapa-140), with targets varying by site class.
As part of the adaptive management process, the riparian scientific advisory group (RSAG) of the cooperative monitoring, evaluation and research committee (CMER) commissioned a study of mature, unmanaged riparian forest stands in western Washington (Schuett-Hames et al., 2005)4. One of the objectives of this study was to determine whether the bapa-140 targets in the forest practices rules were appropriate. The study concluded that the basal area targets are incorrect, but did not provide alternative target values. The study also concluded that there is no statistical difference for basal area targets between site classes.
PROPOSED RULES SUMMARY: The proposed rule changes the DFC target basal area at year 140 (bapa-140). The forest practices board is considering using one value for all site classes, and to use the median value for total live basal area per acre of the Schuett-Hames et al. study data, which is 325 square feet. The board is also considering two alternative proposals that adjust bapa-140 to 325 while modifying other rule provisions. Details are provided below.
ECONOMIC ANALYSIS: To comply with the APA and RFA this analysis identifies potentially affected industries, defines small and large businesses and determines if there is a disproportionate economic impact on small businesses. It also estimates the annual cost of compliance with the proposed rule changes.
Potentially Affected Industries: The rule-complying community affected by the proposal is businesses that own or control the cutting rights on forestland or those with the right to dispose of the timber.
Small Businesses versus Large Businesses: The RFA defines a "small business" as one with fifty or fewer employees. This definition does not lend itself to commercial forestry, because a growing proportion of Washington's commercial forest acreage is owned by investment-oriented firms that employ few people. Forest ownership acreage and the volume of timber harvested on an annual basis are generally more appropriate metrics for characterizing small businesses in the timber industry. In order to better portray the effects of proposed rule changes on small business, this economic analysis defines small businesses as those meeting the state's eligibility criteria for small forest landowner status in the forestry riparian easement program; generally those who harvest an average of less than two million board feet per year from their own land. All other private landowners are categorized as "large businesses" for purposes of this analysis.
Benefits and Costs Included in the Analysis: The costs of the rule change are measured as the potential loss of timber revenue, based on an estimate of the timber volume that is annually affected by the rule making. The intended benefits are related to the value of protecting and restoring habitat for fish and wildlife species that utilize riparian areas for all or part of their life cycles. These benefits cannot be quantified in this analysis because there is no known research applicable to Washington that quantifies the benefits of protecting additional riparian habitat. Methodology and analysis are further discussed below.
Involvement of Concerned Stakeholders: This rule making is the result of the forests and fish adaptive management process described in WAC 222-12-045. It is a formal process involving scientists and policy makers who represent stakeholders of Washington forest practices: Landowners of large and small forestland acreage, environmental and conservation organizations, tribal organizations, federal and state natural resource agencies, and Washington counties.
In reaction to the findings of the Schuett-Hames report, forests and fish policy petitioned the forest practices board to consider rule making responsive to the findings of the study. DNR's forest practices division held several stakeholder meetings starting in May 2006 to develop a rule proposal that would be responsive to the study results. By the board's August 9, 2006, meeting, the participating stakeholders had not reached an agreement on appropriate changes to the basal area targets. At the August 9, 2006, meeting, the board directed staff to distribute a notice pursuant to RCW 76.09.040(2) requesting comments from the Washington department of fish and wildlife, counties and tribes on a proposal that would change the target basal areas listed in WAC 222-16-0021(1) to the study's median value of 325 square feet per acre for all site classes. The board also instructed staff to specify on the notice that the board intended to consider other options that would appropriately respond to the study.
Prior to the board's June 11, 2007, meeting, the Washington forest protection association forwarded another rule proposal to DNR, which was also intended to respond to the findings in the Schuett-Hames report. Since then, DNR has facilitated several stakeholder meetings to further develop that proposal. The resulting rule proposal is referred in this analysis as "proposals 2 and 3."
METHODS OF ANALYSIS: This analysis includes the following:
• | The effects of a change in bapa-140 targets to 325 (median value from Schuett-Hames report) for all site classes (proposal 1); and |
• | The effects of a proposal to change bapa-140 targets to 325 and modifying other provisions of existing rules (proposals 2 and 3). |
Option 1 provisions are the same for proposals 1, 2, and 3. The differences among proposals are under option 2. Like proposal 1, proposals 2 and 3 change the target bapa-140 to 325 for all site classes under option 2.
Option 2 of proposal 2 includes the following differences from existing rules:
• | The target basal area is changed to 325 square feet for all site classes. |
• | The 20 tpa conifers that must be left in the cut portion of the inner zone can be credited to meeting the bapa-140 target of 325. |
• | All harvest sites, regardless of stream size and site class, are eligible to use option 2. |
• | Additional harvesting may be permitted in the outer zone in cases where minimum no-cut floors result in bapa-140 greater than 325 (referred to in this report as "excess basal area"). Outer zone leave trees may be removed down to 10 trees per acre, so long as the minimum bapa-140 of 325 is met. |
• | The target basal area is changed to 325 square feet for all site classes. |
• | The 20 tpa conifers that must be left in the cut portion of the inner zone can be credited to meeting the bapa-140 target of 325. |
These estimates are based on a statewide extrapolation of the data set used by McConnell et al. in the 2007 FPA desktop analysis prepared for the forests and fish CMER, An Overview of the DFC Model and an Analysis of Westside Type F Riparian Prescriptions and Projected Stand Basal Area per Acre7. The data set consists of one hundred fifty randomly selected forest practices applications (FPAs) from 2003 and 2004 that proposed timber harvesting from within the inner portion of the riparian zone in western Washington. The following data from McConnell's data set was used in this economic analysis:
• | Stand characteristics supplied by applicant: Site class, stream size, major species (Douglas-fir or Western Hemlock), core and inner zone acreage, stand age. |
• | Tree inventory data (softwoods and hardwoods). |
• | Stand characteristics calculated from these data: Core and inner zone tpa, current basal area per acre (bapa), projected no-cut basal area per acre at age 140 (bapa-140), outer zone leave trees. |
• | Attributes following model-generated prescription (reported for core and inner zones as appropriate): Current bapa, bapa-140, size of first tree that may be cut (marginal tree dbh), tpa (option 1), no-cut floor (width of no-cut portion of inner zone, option 2). |
Methodological Approach: The basic unit of analysis is basal area. Basal area is used because it allows the comparison of prescriptions that differ within the RMZ area, i.e., zone configuration, zone treatments, average dbh, etc. The amount of basal area that will remain in the inner and outer zones is estimated for both harvest options under existing rules and each rule proposal as follows:
• | For existing rules options 1 and 2, the remaining trees left following permitted treatments, as reported in McConnell's study, is recalculated as basal area. |
• | For option 1 of all three proposals, a growth factor must be applied in order to estimate the amount of basal area needed at the time of harvest to meet the target basal area of 325 at age 140. This basal area is calculated by comparing the bapa growth trajectories of a given stand with no inner zone timber harvest and the bapa-140 following the prescribed thinning in existing regulations. |
• | For option 2 of proposal 1, the no-cut floors are adjusted when necessary to meet the inner zone basal area requirement8. |
• | For option 2 of proposal 2, no-cut floors are calculated for the FPAs permitted to harvest under proposal 2 that are ineligible under existing rules and proposal 1 (site class 3-large streams and site classes 4 and 5). No-cut floors on all FPAs are adjusted if necessary to account for the crediting of the twenty trees per acre in the cut portion of the inner zone to basal-area-per-acre requirements. If the minimum no-cut floor is farther out than the no-cut floor that would be in place in the absence of minimum no-cut floors, the basal area within this section is considered to be "excess basal area." The amount of excess basal area in outer zone trees that may be cut (down to 10 tpa) is then calculated. |
• | For option 2 of proposal 3, the no-cut floors are adjusted when necessary to meet the inner zone basal area requirement and to account for the crediting of the twenty trees per acre in the cut portion of the inner zone to basal-area-per-acre requirements. |
The DFC model and this analysis assume that conifer inventory is evenly spaced throughout the inner area of the riparian zone, and is therefore not sensitive to tree inventory distribution by dbh in the inner zone.
Option 1 and option 2 reported separately. In existing rules, applications for harvest in riparian areas in Site Class 1, 2, or on small streams in Site Class 3 may use harvest options 1 or 2. Site Classes 4, 5 and Site Class 3 on large streams may only use harvest option 1. Of the 150 FPAs in the data set, all one hundred fifty could harvest under option 1, and one hundred eight could harvest under option 2. In practice, all but six of these one hundred eight FPAs chose option 2 as their harvest regime. This appears to be a reflection of ease of operations, rather than maximizing the level of harvest, since option 2 generally results in leaving more basal area than option 1. For this reason, this analysis does not attempt to choose the option that results in the largest inner-zone harvest for each FPA. The analyses for harvest options 1 and 2 are reported separately.
Estimating the value of the additional trees that need to be left in order to meet higher bapa-140 targets: Basal area estimates from McConnell's data set are extrapolated statewide based on FPA activity. Basal area was then converted into timber volume based on average stand characteristics of the one hundred fifty stands in the data set. Timber volume was converted to stumpage values using 2007 DNR timber sales data for western Washington.
EFFECTS OF PROPOSALS ON BASAL AREA LEAVE REQUIREMENTS:
Estimating the number of FPAs that are affected by existing rules and proposed rule changes: The effects of the proposed rule changes on individual FPAs vary, reflecting the wide variability in stand attributes. The effects of existing rules on FPAs are covered in depth in McConnell et al. Table 1 compares the constraints among the proposals for the two options.
For option 1:
• | As reported in McConnell et al., under existing rules, only eight of the one hundred fifty FPAs in the data set are constrained by basal area; the others are constrained by the requirement to leave fifty-seven tpa in the inner zone after thinning. No FPAs are precluded from thinning under existing rules. |
• | Raising the bapa-140 target to 325 (proposals 1, 2 and 3) results in almost half (seventy one) of the FPAs being constrained by bapa-140. The remaining seventy-nine FPAs remain constrained by the fifty-seven tpa requirement and are therefore not affected by the proposed rule change. |
• | Twenty of the FPAs do not have sufficient inner zone conifer inventory to thin under proposals 1, 2, and 3. |
• | As reported in McConnell et al., forty of the one hundred eight FPAs in the data set that are permitted to harvest under option 2 are constrained by basal area under existing rules; the others are constrained by minimum no-cut floors. One FPA has insufficient basal area to perform an option 2 harvest under existing rules. |
• | Minimum no-cut floors constrain only 20% of FPAs under proposals 1 and 2, and 21% under proposal 3. Bapa-140 constrains the remainder. |
• | The percentage of FPAs that cannot harvest conifers in the inner zone is similar for the three proposals - 15%, 17%, and 15%, respectively. |
Forest Practices Applications Constraints on Harvest
Option 1 | Option 2 | |||||
Number of Forest Practices Applications (FPAs) | Existing rules | Proposal 1, 2 and 3 | Existing rules | Proposal 1 | Proposal 2 | Proposal 3 |
Constrained by bapa-140 | 8/150 | 71/150 | 40/108 | 86/108 | 120/150 | 85/108 |
Percent | 5% | 47% | 37% | 80% | 80% | 79% |
No conifers harvested in inner zone | 0/150 | 20/150 | 1/108 | 16/108 | 25/150 | 16/108 |
Percent | 0% | 13% | 1% | 15% | 17% | 15% |
Option 1: Under existing regulations, an average of 57% of conifer basal area is left in the inner zone after thinning. This increases to 69% under the three proposals.
Option 2: For the subset of FPAs that are eligible for option 2 harvest under all three proposals, the differences in leave basal area among the three proposals is relatively minimal. The crediting of cut-area leave trees to basal area requirements under proposals 2 and 3 generally results in a shift of the no-cut floor by zero or one foot. The most significant distinction among the three proposals is that proposal 2 allows option 2 harvest on all site class/stream size combinations. To facilitate comparison, tables 2 and 3 separate leave basal area for proposal 2 into two subgroups: "site class 1, 2, and 3-small," which includes the FPAs eligible to use option 2 under existing rules and all three proposals, and "site class 3-large, 4 and 5," which are ineligible to use option 2 except under proposal 2.
In the subset of one hundred eight FPAs that are eligible to harvest under option 2, 69% of the basal area is left under current rules, increasing to 81% if bapa-140 is increased to 325 (proposal 1), and 80% under proposals 2 and 3. The subgroup that is ineligible to harvest under current rules leaves 86% of bapa-140 under proposal 2.
Proposal 2 permits the harvest of excess basal area via a decrease in the outer leave tree requirement from twenty down to ten trees per acre. The effects of this prescription are presented in Table 4.10
Basal area remaining after harvest in inner and outer zones.
Option 1 - Thinning
Inner Zone conifer basal area (sq. ft.) | Outer Zone conifer basal area (sq. ft.) |
||||||||||||
All FPAs | Site classes 1, 2, and 3 (small streams) |
Site classes 3 (large streams), 4 and 5 |
|||||||||||
# FPAs eligible* |
Before harvest |
After harvest |
% left after harvest |
# FPAs | Before harvest |
After harvest |
% left after harvest |
# FPAs | Before harvest |
After harvest |
% left after harvest |
After harvest |
|
Existing rules |
150 | 62,398 | 35,555 | 57% | 108 | 43,725 | 25,385 | 58% | 42 | 18,673 | 10,170 | 54% | 3,383 |
Proposal 1 |
150 | 62,398 | 42,875 | 69% | 108 | 43,725 | 28,996 | 66% | 42 | 18,673 | 13,880 | 74% | 3,383 |
Proposal 2 |
150 | 62,398 | 27,007 | 43% | 108 | 43,725 | 16,729 | 38% | 42 | 18,673 | 10,278 | 55% | 3,293 |
Basal area remaining after harvest in inner and outer zones.
Option 2 - Leaving trees closest to the stream
Inner Zone conifer basal area (sq. ft.) | Outer
Zone
conifer basal area (sq. ft.) |
||||||||||||
All FPAs | Site classes 1, 2, and 3 (small streams) |
Site classes 3 (large streams), 4 and 5 |
|||||||||||
# FPAs eligible* | Before harvest | After harvest | % left after harvest | # FPAs | Before harvest | After harvest | % left after harvest | # FPAs | Before harvest | After harvest | % left after harvest | After harvest |
|
Existing rules |
108 | 42,068 | 29,107 | 69% | 108 | 42,068 | 29,107 | 69% | 0 | na | na | na | 2,656 |
Proposal 1 |
108 | 42,068 | 34,201 | 81% | 108 | 42,068 | 34,201 | 81% | 0 | na | na | na | 2,656 |
Proposal 2 |
150 | 60,760 | 49,095 | 81% | 108 | 42,068 | 33,336 | 79% | 42 | 18,692 | 15,759 | 84% | 3,161 |
Effects of proposed rule provisions.
Option 2 - Proposal 2
All FPAs | Site classes 1, 2, and 3 (small streams) | Site classes 3 (large streams), 4 and 5 | |
Number of FPAs | 150 | 108 | 42 |
Inner zone conifer basal area | 60,760 | 42,068 | 18,692 |
Basal area left with minimum floors | 49,844 | 33,815 | 16,029 |
Basal area left, no minimum floors | 47,787 | 32,877 | 14,911 |
Excess basal area | 2,057 | 938 | 1,118 |
Number of FPAs with excess basal area | 27 | 23 | 4 |
Basal area of outer zone trees removed | 278 | 245 | 33 |
Inner zone left after prescriptions | 49,556 | 33,570 | 15,996 |
Number of FPAs with excess basal area | 23 | 19 | 4 |
Excess basal area after credits | 1,779 | 694 | 1,085 |
Excess basal area is defined as the difference between the basal area left with and without minimum no-cut floors. For the entire data set, this amounts to 2,057 square feet, approximately 4% of the basal area left prior to adjustments. Of the one hundred fifty FPAs in the data set, twenty-seven have leave excess basal area. The others are not constrained by minimum floors. This differs somewhat from the findings reported for proposal 1 because the basal area of the required twenty leave trees per acre in the cut portion of the inner zone is credited in the calculation of excess basal area.
The basal area of the ten outer zone conifers per acre that may be harvested to mitigate excess basal area amounts to two hundred seventy-eight square feet, less than one half of one percent of the basal area inventory. For most FPAs, there is no difference in leave basal area requirements among the three proposals under option 2.
Statewide extrapolation: The data set used in McConnell et al. was randomly selected from all of the FPAs that included riparian inner-zone harvest in 2003 and 2004. The report describes the situations in which some FPAs were dropped. In cases where there was more than one stream segment, the first stream segment was chosen. For the purposes of extrapolation, these additional stream segments are the equivalent of additional FPAs. There are three hundred forty-eight stream segments in the one hundred fifty sample FPAs, or 2.32 stream segments per FPA. There were three hundred ninety-one FPAs that included riparian zone harvest in 2003, and four hundred forty-four in 2004, for an average of four hundred eighteen. There are, therefore, an estimated nine hundred seventy stream segments where inner zone harvest activity is proposed annually, approximately 6.5 times more riparian area harvest activity per year than is found in the one hundred fifty survey FPAs. Tables 5 and 6 adjust the findings in Tables 2 and 3 to a statewide extrapolation.
Basal area remaining after harvest in inner and outer zones.
Statewide annual extrapolation, Option 1 - Thinning
Inner Zone conifer basal area (sq. ft.) | Outer Zone
conifer basal area (sq. ft.) |
||||||||||||
All FPAs | Site classes 1, 2, and 3 (small streams) |
Site classes 3 (large streams), 4 and 5 |
|||||||||||
# FPAs eligible | Before harvest | After harvest | % left after harvest | # FPAs | Before harvest | After harvest | % left after harvest | # FPAs | Before harvest | After harvest | % left after harvest | After harvest |
|
Existing rules |
970 | 403,505 | 229,925 | 57% | 698 | 282,755 | 164,159 | 58% | 272 | 120,749 | 65,766 | 54% | 21,874 |
Proposal 1 |
970 | 403,505 | 277,262 | 69% | 698 | 282,755 | 187,506 | 66% | 272 | 120,749 | 89,756 | 74% | 21,874 |
Proposal 2 |
970 | 403,505 | 174,643 | 43% | 698 | 282,755 | 108,181 | 38% | 272 | 120,749 | 66,462 | 55% | 21,295 |
Basal area remaining after harvest in inner and outer zones.
Statewide annual extrapolation, Option 2 - Leaving trees closest to the stream
Inner Zone conifer basal area (sq. ft.) | Outer Zone
conifer basal area (sq. ft.) |
||||||||||||
All FPAs | Site classes 1, 2, and 3 (small streams) |
Site classes 3 (large streams), 4 and 5 |
|||||||||||
# FPAs eligible | Before harvest | After harvest | % left after harvest | # FPAs | Before harvest | After harvest | % left after harvest | # FPAs | Before harvest | After harvest | % left after harvest | After harvest |
|
Existing rules |
698 | 272,042 | 188,225 | 69% | 698 | 272,042 | 188,225 | 69% | 0 | na | na | na | 17,167 |
Proposal 1 |
698 | 272,042 | 221,166 | 81% | 698 | 272,042 | 221,166 | 81% | 0 | na | na | na | 17,167 |
Proposal 2 |
970 | 392,917 | 317,479 | 81% | 698 | 272,042 | 215,573 | 79% | 272 | 120,875 | 101,908 | 84% | 20,441 |
• | Westside Douglas-fir fifty-year site index table (to estimate tree height from site index and stand age). |
• | Board foot volume table for young Douglas-fir Scribner Log Rule. |
The average tree height (one hundred nineteen feet) was estimated based on the average stand age (fifty-two) and average site index (one hundred sixteen) of the data set. Volume was then calculated for a fourteen inch dbh Douglas-fir of this height -- two hundred eighteen board feet per tree. Stumpage value was calculated based on recent DNR timber sales results in western Washington. The stumpage price used was $400 per thousand board feet (mbf), appropriate for twelve to eighteen inch diameter trees.11 The result is a stumpage value of $87.20 per tree.
Table 7 presents an estimate of the value of inner zone conifer inventory and the value of inner and outer zone conifers left, on an annual basis, to meet DFC for each scenario. Findings are reported separately for the stands that may harvest under either option under existing rules (site Class 1, 2 and 3-small streams), and those that may only use option 1 (site Class 3-large, 4, and 5).12 Under option 1, out of total inventory of $32.9 million, $18.8 million of stumpage value is left under existing rules, and $22.6 million under the three proposals. Under option 2, total inventory of the site Class 1, 2 and 3-small streams subset is $22.2 million, of which $15.4 million is left under existing rules and $18.0, million $17.7 million, and $17.8 million under proposals 1, 2, and 3 respectively. Inventory under proposal 2, which is available to all site class-stream size combinations, is $32.1 million, and leave stumpage value is $26.1 million.
Stumpage Value
Statewide annual extrapolation (dollar values in millions)
OPTION 1 - Thinning
Inner Zone stumpage value | Outer Zone stumpage value | ||||||||||||
All FPAs | Site classes 1, 2 and 3 (small streams) | Site classes 3 (large streams), 4 and 5 | |||||||||||
# FPAs eligible | Before harvest | After harvest | % left after harvest | # FPAs | Before harvest | After harvest | % left after harvest | # FPAs | Before harvest | After harvest | % left after harvest | After harvest | |
Existing rules |
970 | $32.9 | $18.8 | 57% | 698 | $23.1 | $13.4 | 58% | 272 | $9.8 | $5.4 | $0.5 | $1.8 |
Proposal 1 |
970 | $32.9 | $22.6 | 69% | 698 | $23.1 | $15.3 | 66% | 272 | $9.8 | $7.3 | $0.7 | $1.8 |
Proposal 2 |
970 | $32.9 | $14.2 | 43% | 698 | $23.1 | $8.8 | 38% | 272 | $9.8 | $5.4 | $0.6 | $1.7 |
OPTION 2 – Leaving trees closest to the stream
Inner Zone stumpage value | Outer Zone stumpage value | ||||||||||||
All FPAs | Site classes 1, 2 and 3 (small streams) | Site classes 3 (large streams), 4 and 5 | |||||||||||
# FPAs eligible | Before harvest | After harvest | % left after harvest | # FPAs | Before harvest | After harvest | % left after harvest | # FPAs | Before harvest | After harvest | % left after harvest | After harvest | |
Existing rules |
698 | $22.2 | $15.4 | 69% | 698 | $22.2 | $15.4 | 69% | -- | na | na | na | $1.4 |
Proposal 1 |
698 | $22.2 | $18.0 | 81% | 698 | $22.2 | $18.0 | 81% | -- | na | na | na | $1.4 |
Proposal 2 |
970 | $32.1 | $25.9 | 81% | 698 | $22.2 | $17.6 | 79% | 272 | $9.9 | $8.3 | $0.8 | $1.7 |
COSTS OF PROPOSED RULE CHANGES: As previously mentioned, comparisons among some option/proposal combinations are difficult to make, because option 2 is only available to a subset of site class/stream width combinations under existing rules and proposals 1 and 3, and zone configurations vary. Comparisons based on percentage of basal area left can be made, but such comparisons are somewhat skewed because the site Class 3-large, 4 and 5 subgroup leaves a higher percentage of basal area than the site Class 1, 2 and 3-small subgroup under those scenarios that permit harvesting under all site class/stream size combinations (option 1 scenarios and proposal 2 of option 2). Comparison data provided in Table 8 is thus presented by subgroup as well as in total.
Annual costs of compliance and changes in costs from existing rules (dollar values in millions)
OPTION 1 – Thinning
Inner and
outer zones |
All inner zone | Inner zone
site class 1, 2, and 3-small |
Inner zone
site class 3-large, 4 and 5 |
Outer zone | |
Existing rules | $20.5 | $18.8 | $13.4 | $5.4 | $1.8 |
Proposal 1 | $24.4 | $22.6 | $15.3 | $7.3 | $1.8 |
Cost increase (decrease) |
$3.9 | $3.9 | $1.9 | $2.0 | -- |
Proposal 2 | $16.0 | $14.2 | $8.8 | $5.4 | $1.7 |
Cost increase (decrease) |
($4.6) | ($4.5) | ($4.6) | $0.06 | ($0.05) |
OPTION 2 – Leaving trees closest to the stream
Inner and outer zones | All inner zone | Inner zone
site class 1, 2, and 3-small |
Inner zone
site class 3-large, 4 and 5 |
Outer zone |
|
Existing rules | $16.8 | $15.4 | $15.4 | -- | $1.4 |
Proposal 1 | $19.4 | $18.0 | $18.0 | -- | $1.4 |
Cost increase (decrease) |
$2.7 | $2.7 | $2.7 | -- | -- |
Proposal 2 | $28.6 | $25.9 | $17.6 | $8.3 | $1.7 |
Cost increase (decrease) |
na | na | $2.2 | na | $0.3 |
Option 1 (thinning): Changing the basal area per acre at age 140 (bapa-140) target to 325 (proposal 1) increases the stumpage value of conifers left to meet DFC by $3.9 million annually.
Option 2 (leaving trees closest to the stream): Changing the basal area per acre at age 140 (bapa-140) target to 325 (proposal 1) increases the stumpage value of conifers left to meet DFC by $2.7 million annually. For the subgroup of site class/stream size combinations that may currently use option 2, proposal 2 increases costs by $2.4 million, but results in a savings of $300,000 over proposal 1. Additional costs under proposal 3 are $2.5 million. For the subgroup that may not currently use option 2, comparisons with other option 2 proposals cannot be made. Comparing the stumpage value of leave conifers in this subgroup with option 1 (existing rules) suggests an increase in annual costs of $3.1 million, but a portion of this increase is due to the fact that option 2 generally results in more leave basal area than option 1, so the comparison cannot be readily made.
Small Business Impacts: The one hundred fifty FPAs in the sample were not identified as to small forest landowner status. Anecdotal evidence suggests that nonindustrial landowners are less likely to consider harvesting in riparian zones, due to the complicated nature of following the rules, such as the requirement to inventory each tree by two-inch diameter class. Those that choose to harvest may be more likely to utilize option 2, which is simpler to set up, in spite of the fact that option 1 usually allows more harvesting than option 2. Under these circumstances, we estimate that the effects on small business are similar to the industry as a whole. The major tasks involved in timber sale planning would not change as a result of this rule making, and timber harvests within riparian management zones will continue to be a small percentage of the overall harvest unit. Therefore, it is improbable that this rule making would have an effect on small business employment in the state.
BENEFITS: The goal of the proposed rule making is to facilitate reaching desired future conditions conducive to healthy riparian ecology and function, and ultimately to improve water quality and habitat for fish and wildlife species that utilize riparian areas for all or part of their life cycle. The 1999 forests and fish report, which initiated the current riparian strategies for forest practices rules, based recommendations for improving and maintaining "bank stability, recruitment of large woody debris, leaf litter fall, nutrients, sediment filtering, shade, and other riparian features that are important to both riparian forest and aquatic system conditions."13 The report also initiated an adaptive management program through which adjustments in the rules would be made to achieve resource objectives. The proposed rule proposals are a manifestation of that program and are intended to provide enhanced benefits to water quality and fish and wildlife habitat.
The benefits of the three proposals are difficult to analyze. The economic benefits of the proposed rule change cannot be reasonably estimated because they occur at the margin, and marginal benefits of protecting riparian areas haven't been studied. Some general inferences can be made from the data set, however. In twenty of the one hundred fifty sample FPAs, bapa-140 increased after the prescribed option 1 thinning treatment under existing rules compared to bapa-140 without a thinning. On the other hand, none of the one hundred eight eligible FPAs increased bapa-140 after an option 2 treatment. The fact that the vast majority (one hundred two out of one hundred eight) of FPAs in the sample chose option 2 over option 1 even though more trees are left under option 2, and the large standard deviation in the mature stands reported by the Schuett-Hames study, suggest that the current structure may be counterproductive for stands that would benefit from thinning but cannot meet bapa-140 targets. Increasing bapa-140 targets may exacerbate the situation. Furthermore, there are no provisions in the proposed rule to incentivize option 1 thinning treatments.
CONCLUSIONS: This economic analysis estimates the costs of the proposed rule making on an annual basis. Costs are defined as the annual statewide decrease in timber harvest revenue resulting from the proposed rule change. These estimates are based on a statewide extrapolation of the data set used by McConnell et al. in the 2007 CMER report, An Overview of the DFC Model and an Analysis of Westside Type F Riparian Prescriptions and Projected Stand Basal Area per Acre.
The annual change from existing rules in stumpage value of trees not harvested under proposal 1 is $3.9 million under option 1 (thinning) and $2.7 million under option 2 (packing). Proposals 2 and 3 result in slightly more option 2 harvested stumpage than proposal 1. The significant difference amongst the proposals is that proposal 2 allows the packing option on all site class/stream size combinations.
As discussed in the McConnell et al. report, this analysis necessitated making a number of assumptions that were not field tested. These findings should therefore be considered at best as providing an indication of the scale of the effects of the proposed rule change. In addition, shade rule requirements may further limit harvest under option 1 for some stands.
The effects on small businesses appear to be similar to the industry as a whole for both proposals 1 and 2, and none of the proposals appear to have disproportionate negative impacts on small forest landowners when compared to Washington timber industry businesses overall. The major tasks involved in timber sale planning would not change as a result of this rule making, and timber harvests within riparian management zones will continue to be a small percentage of the overall harvest unit. Therefore, it is improbable that this rule making would have an effect on small business employment in the state.
Benefits are identified as the value of achieving DFC in riparian areas, but are not quantified due to the lack of available relevant information.
Consideration should also be given to the distribution of costs and benefits. While the benefits accrue generally, the costs are borne by a limited number of forest practices applicants. The effects on individual applications vary considerably. Using option 1, about half of the FPAs are unaffected by changing the bapa-140 target to 325 (proposal 1), because they have more than sufficient basal area, and would still be constrained by the fifty-seven trees-per-acre requirement. On the other hand, as mentioned previously, 13% of the FPAs would be precluded from option 1 harvesting under proposal 1, because they are unable to meet bapa-140 in the core plus inner zones. Some of these stands might be more likely to meet DFC with an appropriate thinning.
ACKNOWLEDGMENT: We would like to thank Steven B. McConnell, Upper Columbia United Tribes, for providing the data essential to this analysis, through both the CMER desktop analysis referenced throughout this document and his willingness to work with DNR staff during this analysis.
RESOURCES CITED: McConnell, S. 2007. An Overview of the DFC Model and an Analysis of Westside Type F Riparian Prescriptions and Projected Stand Basal Area per Acre. Project Title: The FPA Desktop Analysis. Contract No. PSC 07-22.
Schuett-Hames, D., R. Conrad, A. Roorbach. 2005. Validation of the Western Washington Riparian Desired Future Condition Performance Targets in the Washington State Forest Practice Rules with Data from Mature, Unmanaged, Conifer-Dominated Riparian Stands. Northwest Indian Fisheries Commission, CMER No. 05-507.
1 For CBA requirements, see RCW 34.05.328 - The Washington state legislature.
2 For SBEIS requirements, see RCW 19.85.040 - The Washington state legislature.
3 See forest practices rules - TITLE 222 WAC for details.
4 This study is available at http://www.dnr.wa.gov/forestpractices/adaptivemanagement/cmer/publications/CMER_05_507.pdf.
5 Refer to WAC 222-30-021 (1)(b)(ii)(B)(I)(II), and Section 7 of the forest practices board manual for existing rules and information pertaining to riparian zone harvest.
6 Outer zone trees are included in the analyses to ensure the comparability of the scenarios.
7 See http://www.dnr.wa.gov/forestpractices/adaptivemanagement/cmer/projects/.
8 Under proposal 1's option 2, harvesters that are constrained by the minimum floor area may harvest up to one-half of the trees in the outer riparian zone on a basal area for basal area basis (maintaining a minimum of ten trees per acre), reported as a basal area credit. Increasing bapa-140 targets will affect this credit, but since the model provides insufficient information to calculate this, these trees have been ignored for this analysis.
9 The effects of shade rule requirements are not included in the data provided in tables 2 and 3, but are discussed below.
10 Existing rules also allow for the harvest of ten outer zone trees on a basal-area-by-basal-area basis.
11 Stumpage price is net of costs; costs are assumed to be $150/mbf.
12 This is done in order to allow comparison among like groups; in this case, the subset of stands that may use either option 1 or option 2.
13 Forests and Fish Report, 1999. Appendix B (I)(b). This report may be accessed at http://www.dnr.wa.gov/forestpractices/adaptivemanagement/, under "Adaptive Management Links."
A copy of the statement may be obtained by contacting Gretchen Robinson, P.O. Box 47012, Olympia, WA 98504-7012, phone (360) 902-1705, fax (360) 902-1428, e-mail gretchen.robinson@dnr.wa.gov.
A cost-benefit analysis is required under RCW 34.05.328. A preliminary cost-benefit analysis may be obtained by contacting Gretchen Robinson, P.O. Box 47012, Olympia, WA 98504-7012, phone (360) 902-1705, fax (360) 902-1428, e-mail gretchen.robinson@dnr.wa.gov. Note: The small business economic impact statement and the preliminary cost-benefit analysis are combined in the document, Preliminary Economic Analysis, Forest Practices Rule Making, Affecting Timber Harvest in Riparian Zones in Western Washington.
June 17, 2008
Victoria Christiansen
Chair
OTS-1067.2
AMENDATORY SECTION(Amending WSR 05-12-119, filed 5/31/05,
effective 7/1/05)
WAC 222-30-021
*Western Washington riparian management
zones.
These rules apply to all typed waters on forest land
in Western Washington, except as provided in WAC 222-30-023. RMZs are measured horizontally from the outer edge of the
bankfull width or channel migration zone, whichever is
greater, and extend to the limits as described in this
section. See ((the)) board manual section 7 for riparian
design and layout guidelines.
*(1) Western Washington RMZs for Type S and F Waters have three zones: The core zone is nearest to the water, the inner zone is the middle zone, and the outer zone is furthest from the water. (See definitions in WAC 222-16-010.) RMZ dimensions vary depending on the site class of the land, the management harvest option, and the bankfull width of the stream. See tables for management options 1 and 2 below.
None of the limitations on harvest in each of the three zones listed below will preclude or limit the construction and maintenance of roads for the purpose of crossing streams in WAC 222-24-030 and 222-24-050, or the creation and use of yarding corridors in WAC 222-30-060(1).
The shade requirements in WAC 222-30-040 must be met regardless of harvest opportunities provided in the inner zone RMZ rules. See the board manual section 1.
(a) Core zones. No timber harvest or construction is allowed in the core zone except operations related to forest roads as detailed in subsection (1) of this section. Any trees cut for or damaged by yarding corridors in the core zone must be left on the site. Any trees cut as a result of road construction to cross a stream may be removed from the site, unless used as part of a large woody debris placement strategy or as needed to reach stand requirements.
(b) Inner zones. Forest practices in the inner zone must be conducted in such a way as to meet or exceed stand requirements to achieve the goal in WAC 222-30-010(2). The width of the inner zone is determined by site class, bankfull width, and management option. Timber harvest in this zone must be consistent with the stand requirements in order to reach the desired future condition targets.
"Stand requirement" means a number of trees per acre, the basal area and the proportion of conifer in the combined inner zone and adjacent core zone so that the growth of the trees would meet desired future conditions. The following table defines basal area targets when the stand is 140 years old.
Site Class | Desired future condition target basal area per acre (at 140 years) |
I | (( |
II | (( |
III | (( |
IV | (( |
V | (( |
(i) Hardwood conversion in the inner zone. When the existing stands in the combined core and inner zone do not meet stand requirements, no harvest is permitted in the inner zone, except in connection with hardwood conversion.
(A) The landowner may elect to convert hardwood-dominated stands in the inner zone to conifer-dominated stands. Harvesting and replanting shall be in accordance with the following limits:
(I) Conversion activities in the inner zone of any harvest unit are only allowed where all of the following are present:
• Existing stands in the combined core and inner zone do not meet stand requirements (WAC 222-30-021 (1)(b));
• There are fewer than 57 conifer trees per acre 8 inches or larger dbh in the conversion area;
• There are fewer than 100 conifer trees per acre larger than 4 inches dbh in the conversion area;
• There is evidence (such as conifer stumps, historical photos, or a conifer understory) that the conversion area can be successfully reforested with conifer and support the development of conifer stands;
• The landowner owns 500 feet upstream and 500 feet downstream of the harvest unit;
• The core and inner zones contain no stream adjacent parallel roads;
• Riparian areas contiguous to the proposed harvest unit are owned by the landowner proposing to conduct the conversion activities, and meet shade requirements of WAC 222-30-040 or have a 75-foot buffer with trees at least 40 feet tall on both sides of the stream for 500 feet upstream and 500 feet downstream of the proposed harvest unit (or the length of the stream, if less);
• If the landowner has previously converted hardwood-dominated stands, then post-harvest treatments must have been performed to the satisfaction of the department.
(II) In addition to the conditions set forth above, permitted conversion activities in the inner zone of any harvest unit are limited by the following:
• Each continuous conversion area is not more than 500 feet in length; two conversion areas will be considered "continuous" unless the no-harvest area separating the two conversion areas is at least half the length of the larger of the two conversion areas.
• Type S and F (Type 1, 2, or 3) Water: Up to 50% of the inner zone area of the harvest unit on one side of the stream may be converted provided that:
♦ The landowner owns the opposite side of the stream and the landowner's riparian area on the opposite bank meets the shade requirements of WAC 222-30-040 or has a 75-foot buffer of trees at least 40 feet tall or:
♦ The landowner does not own land on the opposite side of the stream but the riparian area on the opposite bank meets the shade requirements of WAC 222-30-040 or has a 75-foot buffer of trees at least 40 feet tall.
• Not more than 25% of the inner zone of the harvest unit on both sides of a Type S or F Water may be converted if the landowner owns both sides.
(III) Where conversion is allowed in the inner zone, trees within the conversion area may be harvested except that:
• Conifer trees larger than 20 inches dbh shall not be harvested;
• Not more than 10% of the conifer stems greater than 8 inches dbh, exclusive of the conifer noted above, within the conversion area may be harvested; and
• The landowner must exercise reasonable care in the conduct of harvest activities to minimize damage to all residual conifer trees within the conversion area including conifer trees less than 8 inches dbh.
(IV) Following harvest in conversion areas, the landowner must:
• Reforest the conversion area with conifer tree species suitable to the site in accordance with the requirements of WAC 222-34-010; and
• Conduct post-harvest treatment of the site until the conifer trees necessary to meet acceptable stocking levels in WAC 222-34-010(2) have crowns above the brush or until the conversion area contains a minimum of 150 conifer trees greater than 8 inches dbh per acre.
• Notify the department in writing within three years of the approval of the forest practices application for hardwood conversion, if the hardwood conversion has been completed.
(V) Tracking hardwood conversion. The purpose of tracking hardwood conversion is to determine if hardwood conversion is resulting in adequate enhancement of riparian functions toward the desired future condition while minimizing the short term impacts on functions. The department will use existing or updated data bases developed in cooperation with the Washington Hardwoods Commission to identify watershed administrative units (WAUs) with a high percentage of hardwood-dominated riparian areas and, thus have the potential for excessive hardwood conversion under these rules. The department will track the rate of conversion of hardwoods in the riparian zone: (1) Through the application process on an annual basis; and (2) at a WAU scale on a biennial basis as per WAC 222-30-120 through the adaptive management process which will develop thresholds of impact for hardwood conversion at the watershed scale.
(ii) Harvest options.
(A) No inner zone management. When the existing stands in the combined core and inner zone do not meet stand requirements, no harvest is permitted in the inner zone. When no harvest is permitted in the inner zone or the landowner chooses not to enter the inner zone, the width of core, inner and outer zones are as provided in the following table:
No inner zone management RMZ widths for Western Washington
Site Class | RMZ width | Core zone
width
|
Inner zone width
|
Outer zone width
|
||
stream width ≤10' |
stream width >10' | stream width ≤10' | stream width >10' | |||
I | 200' | 50' | 83' | 100' | 67' | 50' |
II | 170' | 50' | 63' | 78' | 57' | 42' |
III | 140' | 50' | 43' | 55' | 47' | 35' |
IV | 110' | 50' | 23' | 33' | 37' | 27' |
V | 90' | 50' | 10' | 18' | 30' | 22' |
(B) Inner zone management. If trees can be harvested and removed from the inner zone because of surplus basal area consistent with the stand requirement, the harvest and removal of the trees must be undertaken consistent with one of two options:
(I) Option 1. Thinning from below. The objective of thinning is to distribute stand requirement trees in such a way as to shorten the time required to meet large wood, fish habitat and water quality needs. This is achieved by increasing the potential for leave trees to grow larger than they otherwise would without thinning. Thinning harvest under option 1 must comply with the following:
• Residual trees left in the combined core and inner zones must meet stand requirements necessary to be on a trajectory to desired future condition. See board manual section 7 for guidelines.
• Thinning must be from below, meaning the smallest dbh trees are selected for harvest first, then progressing to successively larger diameters.
• Thinning cannot decrease the proportion of conifer in the stand.
• Shade retention to meet the shade rule must be confirmed by the landowner for any harvest inside of 75 feet from the outer edge of bankfull width or outer edge of CMZ, whichever is greater.
• The number of residual conifer trees per acre in the inner zone will equal or exceed 57.
Option 1. Thinning from below.
Site class |
RMZ width |
Core zone width
|
Inner zone width
|
Outer zone width
|
||
stream width ≤10' |
stream width >10' |
stream width ≤10' |
stream width >10' |
|||
I | 200' | 50' | 83' | 100' | 67' | 50' |
II | 170' | 50' | 63' | 78' | 57' | 42' |
III | 140' | 50' | 43' | 55' | 47' | 35' |
IV | 110' | 50' | 23' | 33' | 37' | 27' |
V | 90' | 50' | 10' | 18' | 30' | 22' |
(II) Option 2. Leaving trees closest to the water. Management option 2 applies only to riparian management zones for site class I, II, and III on streams that are less than or equal to 10 feet wide and RMZs in site class I and II for streams greater than 10 feet wide. Harvest must comply with the following:
• Harvest is not permitted within 30 feet of the core zone for streams less than or equal to 10 feet wide and harvest is not permitted within 50 feet of the core zone for streams greater than 10 feet wide;
• Residual leave trees in the combined core and inner zone must meet stand requirements necessary to be on a trajectory to desired future condition. See board manual section 7 for calculating stand requirements;
• A minimum of 20 conifers per acre, with a minimum 12-inch dbh, will be retained in any portion of the inner zone where harvest occurs. These riparian leave trees will not be counted or considered towards meeting applicable stand requirements nor can the number be reduced below 20 for any reason.
• Trees are selected for harvest starting from the outer most portion of the inner zone first then progressively closer to the stream.
• If (II) of this subsection results in surplus basal area per the stand requirement, the landowner may take credit for the surplus by harvesting additional riparian leave trees required to be left in the adjacent outer zone on a basal area-for-basal area basis. The number of leave trees in the outer zone can be reduced only to a minimum of 10 trees per acre.
Option 2. Leaving trees closest to water.
Site class | RMZ width | Core zone
width
|
Inner zone width | Outer zone width
|
|||||
stream
width ≤10' |
stream
width ≤10' |
stream
width >10' |
stream
width >10' |
stream
width ≤10' |
stream
width >10' |
||||
minimum floor distance | minimum floor distance | ||||||||
(measured from outer edge of core zone) | (measured from outer edge of core zone) | (measured from outer edge of core zone) | (measured from outer edge of core zone) | ||||||
I | 200' | 50' | 84' | 30' | 84' | 50' | 66' | 66' | |
II | 170' | 50' | 64' | 30' | 70' | 50' | 56' | 50' | |
III | 140' | 50' | 44' | 30' | ** | ** | 46' | ** |
(iii) Where the basal area components of the stand
requirement cannot be met within the sum of the areas in the
inner and core zone due to the presence of a stream-adjacent
parallel road in the inner or core zone, a determination must
be made of the approximate basal area that would have been
present in the inner and core zones if the road was not
occupying space in the core or inner zone and the shortfall in
the basal area component of the stand requirement. See
definition of "stream-adjacent parallel road" in WAC 222-16-010.
(A) Trees containing basal area equal to the amount determined in (iii) of this subsection will be left elsewhere in the inner or outer zone, or if the zones contain insufficient riparian leave trees, substitute riparian leave trees will be left within the RMZ width of other Type S or F Waters in the same unit or along Type Np or Ns Waters in the same unit in addition to all other RMZ requirements on those same Type S, F, Np or Ns Waters.
(B) When the stream-adjacent road basal area calculated in (iii) of this subsection results in an excess in basal area (above stand requirement) then the landowner may receive credit for such excess which can be applied on a basal area-by-basal area basis against the landowner's obligation to leave trees in the outer zone of the RMZ of such stream or other waters within the same unit, provided that the number of trees per acre in the outer zone is not reduced to less than 10 trees per acre.
(C) When the basal area requirement cannot be met, as explained in (iii) of this subsection, the shortfall may be reduced through the implementation of an acceptable large woody debris placement plan. See board manual section 26 for guidelines.
(iv) If a harvest operation includes both yarding and harvest activities within the RMZ, all calculations of basal area for stand requirements will be determined as if the yarding corridors were constructed prior to any other harvest activities. If trees cut or damaged by yarding are taken from excess basal area, these trees may be removed from the inner zone. Trees cut or damaged by yarding in a unit which does not meet the basal area target of the stand requirements cannot be removed from the inner zone. Any trees cut or damaged by yarding in the core zone may not be removed.
(c) Outer zones. Timber harvest in the outer zone must leave 20 riparian leave trees per acre after harvest. "Outer zone riparian leave trees" are trees that must be left after harvest in the outer zone in Western Washington. Riparian leave trees must be left uncut throughout all future harvests:
Outer zone riparian leave tree requirements
Application | Leave tree spacing | Tree species | Minimum dbh required |
Outer zone | Dispersed | Conifer | 12" dbh or greater |
Outer zone | Clumped | Conifer | 12" dbh or greater |
Protection of sensitive features | Clumped | Trees representative of the overstory including both hardwood and conifer | 8" dbh or greater |
The 20 riparian leave trees to be left can be reduced in number under the circumstances delineated in (c)(iv) of this subsection. The riparian leave trees must be left on the landscape according to one of the following two strategies. A third strategy is available to landowners who agree to a LWD placement plan.
(i) Dispersal strategy. Riparian leave trees, which means conifer species with a diameter measured at breast height (dbh) of 12 inches or greater, must be left dispersed approximately evenly throughout the outer zone. If riparian leave trees of 12" dbh or greater are not available, then the next largest conifers must be left. If conifers are not present, riparian leave trees must be left according to the clumping strategy in subsection (ii) below.
(ii) Clumping strategy. Riparian leave trees must be left clumped in the following way:
(A) Clump trees in or around one or more of the following sensitive features to the extent available within the outer zone. When clumping around sensitive features, riparian leave trees must be 8 inches dbh or greater and representative of the overstory canopy trees in or around the sensitive feature and may include both hardwood and conifer species. Sensitive features are:
(I) Seeps and springs;
(II) Forested wetlands;
(III) Topographic locations (and orientation) from which leave trees currently on the site will be delivered to the water;
(IV) Areas where riparian leave trees may provide windthrow protection;
(V) Small unstable, or potentially unstable, slopes not of sufficient area to be detected by other site evaluations. See WAC 222-16-050 (1)(d).
(VI) ((Archeological)) Archaeological or historical sites
registered with the Washington state ((office)) department of
((archeology)) archaeology and historic preservation. See WAC 222-16-050 (1)(g); or
(VII) Sites containing evidence of Native American cairns, graves or glyptic records. See WAC 222-16-050 (1)(f).
(B) If sensitive features are not present, then clumps must be well distributed throughout the outer zone and the leave trees must be of conifer species with a dbh of 12 inches or greater. When placing clumps, the applicant will consider operational and biological concerns. Tree counts must be satisfied regardless of the presence of stream-adjacent parallel roads in the outer zone.
(iii) Large woody debris in-channel placement strategy. A landowner may design a LWD placement plan in cooperation with the department of fish and wildlife. The plan must be consistent with guidelines in the board manual section 26. The landowner may reduce the number of trees required to be left in the outer zone to the extent provided in the approved LWD placement plan. Reduction of trees in the outer zone must not go below a minimum of 10 trees per acre. If this strategy is chosen, a complete forest practices application must include a copy of the WDFW approved hydraulics project approval (HPA) permit.
(iv) Twenty riparian leave trees must be left after harvest with the exception of the following:
(A) If a landowner agrees to implement a placement strategy, see (iii) of this subsection.
(B) If trees are left in an associated channel migration zone, the landowner may reduce the number of trees required to be left according to the following:
(I) Offsets will be measured on a basal area-for-basal area basis.
(II) Conifer in a CMZ equal to or greater than 6" dbh will offset conifer in the outer zone at a one-to-one ratio.
(III) Hardwood in a CMZ equal to or greater than 10" dbh will offset hardwood in the outer zone at a one-to-one ratio.
(IV) Hardwood in a CMZ equal to or greater than 10" dbh will offset conifer in the outer zone at a three-to-one ratio.
*(2) Western Washington protection for Type Np and Ns Waters.
(a) An equipment limitation zone is a 30-foot wide zone measured horizontally from the outer edge of the bankfull width of a Type Np or Ns Water where equipment use and other forest practices that are specifically limited by these rules. It applies to all perennial and seasonal streams.
(i) On-site mitigation is required if any of the following activities exposes the soil on more than 10% of the surface area of the zone:
(A) Ground based equipment;
(B) Skid trails;
(C) Stream crossings (other than existing roads); or
(D) Cabled logs that are partially suspended.
(ii) Mitigation must be designed to replace the equivalent of lost functions especially prevention of sediment delivery. Examples include water bars, grass seeding, mulching, etc.
(iii) Nothing in this subsection (2) reduces or eliminates the department's authority to prevent actual or potential material damage to public resources under WAC 222-46-030 or 222-46-040 or any related authority to condition forest practices notifications or applications.
(b) Sensitive site and RMZs protection along Type Np Waters. Forest practices must be conducted to protect Type Np RMZs and sensitive sites as detailed below:
(i) A 50-foot, no-harvest buffer, measured horizontally from the outer edge of bankfull width, will be established along each side of the Type Np Water as follows:
Required no-harvest, 50-foot buffers
on Type Np Waters.
Length of Type Np Water from the confluence of Type S or F Water | Length of 50' buffer required on Type Np Water (starting at the confluence of the Type Np and connecting water) |
Greater than 1000' | 500' |
Greater than 300' but less than 1000' | Distance of the greater of 300' or 50% of the entire length of the Type Np Water |
Less than or equal to 300' | The entire length of Type Np Water |
(ii) No timber harvest is permitted in an area within 50 feet of the outer perimeter of a soil zone perennially saturated from a headwall seep.
(iii) No timber harvest is permitted in an area within 50 feet of the outer perimeter of a soil zone perennially saturated from a side-slope seep.
(iv) No timber harvest is permitted within a 56-foot radius buffer patch centered on the point of intersection of two or more Type Np Waters.
(v) No timber harvest is permitted within a 56-foot radius buffer patch centered on a headwater spring or, in the absence of a headwater spring, on a point at the upper most extent of a Type Np Water as defined in WAC 222-16-030(3) and 222-16-031.
(vi) No timber harvest is permitted within an alluvial fan.
(vii) At least 50% of a Type Np Waters' length must be protected by buffers on both sides of the stream (2-sided buffers). Buffered segments must be a minimum of 100 feet in length. If an operating area is located more than 500 feet upstream from the confluence of a Type S or F Water and the Type Np Water is more than 1,000 feet in length, then buffer the Type Np Water according to the following table. If the percentage is not met by protecting sensitive sites listed in (b)(i) through (vii) of this subsection, then additional buffers are required on the Type Np Water to meet the requirements listed in the table.
Minimum percent of length of Type Np Waters to be buffered when more than 500 feet upstream from the confluence of a Type S or F Water
Total length of a Type Np Water upstream from the confluence of a Type S or F Water | Percent of length of Type Np Water that must be protected with a 50 foot no harvest buffer more than 500 feet upstream from the confluence of a Type S or F Water |
1000 feet or less | Refer to table in this subsection (i) above |
1001 - 1300 feet | 19% |
1301 - 1600 feet | 27% |
1601 - 2000 feet | 33% |
2001 - 2500 feet | 38% |
2501 - 3500 feet | 42% |
3501 - 5000 feet | 44% |
Greater than 5000 feet | 45% |
The landowner must select the necessary priority areas for additional 2-sided buffers according to the following priorities:
(A) Low gradient areas;
(B) Perennial water reaches of nonsedimentary rock with gradients greater than 20% in the tailed frog habitat range;
(C) Hyporheic and ground water influence zones; and
(D) Areas downstream from other buffered areas.
Except for the construction and maintenance of road crossings and the creation and use of yarding corridors, no timber harvest will be allowed in the designated priority areas. Landowners must leave additional acres equal to the number of acres (including partial acres) occupied by an existing stream-adjacent parallel road within a designated priority area buffer.
(c) None of the limitations on harvest in or around Type Np Water RMZs or sensitive sites listed in (b) of this subsection will preclude or limit:
(i) The construction and maintenance of roads for the purpose of crossing streams in WAC 222-24-030 and 222-24-050.
(ii) The creation and use of yarding corridors in WAC 222-30-060(1).
To the extent reasonably practical, the operation will both avoid creating yarding corridors or road crossings through Type Np Water RMZ or sensitive sites and associated buffers, and avoid management activities which would result in soil compaction, the loss of protective vegetation or sedimentation in perennially moist areas.
Where yarding corridors or road crossings through Type Np Water RMZs or sensitive sites and their buffers cannot reasonably be avoided, the buffer area must be expanded to protect the sensitive site by an area equivalent to the disturbed area or by providing comparable functions through other management initiated efforts.
Landowners must leave additional acres equal to the number of acres (including partial acres) occupied by an existing stream-adjacent parallel road within a Type Np Water RMZs or sensitive site buffer.
[Statutory Authority: RCW 76.09.040. 05-12-119, § 222-30-021, filed 5/31/05, effective 7/1/05. Statutory Authority: Chapter 34.05 RCW, RCW 76.09.040, [76.09.]050, [76.09.]370, 76.13.120(9). 01-12-042, § 222-30-021, filed 5/30/01, effective 7/1/01.]
OTS-1068.5
AMENDATORY SECTION(Amending WSR 05-12-119, filed 5/31/05,
effective 7/1/05)
WAC 222-30-021
*Western Washington riparian management
zones.
These rules apply to all typed waters on forest land
in Western Washington, except as provided in WAC 222-30-023. RMZs are measured horizontally from the outer edge of the
bankfull width or channel migration zone, whichever is
greater, and extend to the limits as described in this
section. See ((the)) board manual section 7 for riparian
design and layout guidelines.
*(1) Western Washington RMZs for Type S and F Waters have
three zones: The core zone is nearest to the water, the inner
zone is the middle zone, and the outer zone is furthest from
the water. (See definitions in WAC 222-16-010.) RMZ
dimensions vary depending on the site class of the land, the
management harvest option, and the bankfull width of the
stream. See ((tables for)) management options 1 and 2 below.
None of the limitations on harvest in each of the three zones listed below will preclude or limit the construction and maintenance of roads for the purpose of crossing streams in WAC 222-24-030 and 222-24-050, or the creation and use of yarding corridors in WAC 222-30-060(1).
The shade requirements in WAC 222-30-040 must be met
regardless of harvest opportunities provided in the ((inner
zone)) RMZ rules. See ((the)) board manual section 1.
(a) Core zones. No timber harvest or construction is
allowed ((in)) within the fifty-foot core zone except
operations related to forest roads as detailed in subsection
(1) of this section. Any trees cut for or damaged by yarding
corridors in the core zone must be left on the site. Any
trees cut as a result of road construction to cross a stream
may be removed from the site, unless used as part of a large
woody debris placement strategy or as needed to reach stand
requirements.
(b) Inner zones. Forest practices in the inner zone must be conducted in such a way as to meet or exceed stand requirements to achieve the goal in WAC 222-30-010(2). The width of the inner zone is determined by site class, bankfull width, and management options as described in this section. Timber harvest in this zone must be consistent with the stand requirements in order to reach the desired future condition targets.
"Stand requirement" means a number of trees per acre, the
basal area and the proportion of conifer in the combined inner
zone and adjacent core zone so that the growth of the trees
would meet desired future conditions of three hundred
twenty-five square feet per acre for all site classes at age
one hundred forty. The growth modeling program provided by
the department must be used to calculate whether a particular
stand meets the stand requirement and is on a trajectory
towards the desired future condition basal area target. ((The
following table defines basal area targets when the stand is
140 years old.))
(( |
|
(i) Hardwood conversion in the inner zone. When the existing stands in the combined core and inner zone do not meet stand requirements, no harvest is permitted in the inner zone, except in connection with hardwood conversion.
(A) The landowner may elect to convert hardwood-dominated stands in the inner zone to conifer-dominated stands. Harvesting and replanting shall be in accordance with the following limits:
(I) Conversion activities in the inner zone of any harvest unit are only allowed where all of the following are present:
• Existing stands in the ((combined core and)) inner zone
do not meet stand requirements (WAC 222-30-021 (1)(b));
• There are fewer than ((57)) fifty-seven conifer trees
per acre ((8)) eight inches or larger dbh in the conversion
area;
• There are fewer than ((100)) one hundred conifer trees
per acre larger than ((4)) four inches dbh in the conversion
area;
• There is evidence (such as conifer stumps, historical photos, or a conifer understory) that the conversion area can be successfully reforested with conifer and support the development of conifer stands;
• The landowner owns ((500)) five hundred feet upstream
and ((500)) five hundred feet downstream of the harvest unit;
• The core and inner zones contain no stream adjacent parallel roads;
• Riparian areas contiguous to the proposed harvest unit
are owned by the landowner proposing to conduct the conversion
activities, and meet shade requirements of WAC 222-30-040 or
have a ((75)) seventy-five-foot buffer with trees at least
((40)) forty feet tall on both sides of the stream for ((500))
five hundred feet upstream and ((500)) five hundred feet
downstream of the proposed harvest unit (or the length of the
stream, if less);
• If the landowner has previously converted hardwood-dominated stands, then post-harvest treatments must have been performed to the satisfaction of the department.
(II) In addition to the conditions set forth above, permitted conversion activities in the inner zone of any harvest unit are limited by the following:
• Each continuous conversion area is not more than
((500)) five hundred feet in length; two conversion areas will
be considered "continuous" unless the no-harvest area
separating the two conversion areas is at least half the
length of the larger of the two conversion areas.
• Type S and F (Type 1, 2, or 3) Water: Up to ((50%))
fifty percent of the inner zone area of the harvest unit on
one side of the stream may be converted provided that:
♦ The landowner owns the opposite side of the stream and
the landowner's riparian area on the opposite bank meets the
shade requirements of WAC 222-30-040 or has a ((75))
seventy-five-foot buffer of trees at least ((40)) forty feet
tall or:
♦ The landowner does not own land on the opposite side of
the stream but the riparian area on the opposite bank meets
the shade requirements of WAC 222-30-040 or has a ((75))
seventy-five-foot buffer of trees at least ((40)) forty feet
tall.
• Not more than ((25%)) twenty-five percent of the inner
zone of the harvest unit on both sides of a Type S or F Water
may be converted if the landowner owns both sides.
(III) Where conversion is allowed in the inner zone, trees within the conversion area may be harvested except that:
• Conifer trees larger than ((20)) twenty inches dbh
shall not be harvested;
• Not more than ((10%)) ten percent of the conifer stems
greater than ((8)) eight inches dbh, exclusive of the conifer
noted above, within the conversion area may be harvested; and
• The landowner must exercise reasonable care in the
conduct of harvest activities to minimize damage to all
residual conifer trees within the conversion area including
conifer trees less than ((8)) eight inches dbh.
(IV) Following harvest in conversion areas, the landowner must:
• Reforest the conversion area with conifer tree species suitable to the site in accordance with the requirements of WAC 222-34-010; and
• Conduct post-harvest treatment of the site until the
conifer trees necessary to meet acceptable stocking levels in
WAC 222-34-010(2) have crowns above the brush or until the
conversion area contains a minimum of ((150)) one hundred
fifty conifer trees greater than ((8)) eight inches dbh per
acre.
• Notify the department in writing within three years of the approval of the forest practices application for hardwood conversion, if the hardwood conversion has been completed.
(V) Tracking hardwood conversion. The purpose of tracking hardwood conversion is to determine if hardwood conversion is resulting in adequate enhancement of riparian functions toward the desired future condition while minimizing the short term impacts on functions. The department will use existing or updated data bases developed in cooperation with the Washington Hardwoods Commission to identify watershed administrative units (WAUs) with a high percentage of hardwood-dominated riparian areas and, thus have the potential for excessive hardwood conversion under these rules. The department will track the rate of conversion of hardwoods in the riparian zone: (1) Through the application process on an annual basis; and (2) at a WAU scale on a biennial basis as per WAC 222-30-120 through the adaptive management process which will develop thresholds of impact for hardwood conversion at the watershed scale.
(ii) Harvest options.
(A) No inner zone management. When the existing stands in the combined core and inner zone do not meet stand requirements, no harvest is permitted in the inner zone. When no harvest is permitted in the inner zone or the landowner chooses not to enter the inner zone, the width of core, inner and outer zones are as provided in the following table:
No inner zone management RMZ widths for Western Washington
Site Class | Total RMZ width | ((
|
Combined core and inner zone
width
|
Outer zone width
|
||
stream width ≤10' |
stream width >10' | stream width ≤10' | stream width >10' | |||
I | 200' | (( |
(( |
(( |
67' | 50' |
II | 170' | (( |
(( |
(( |
57' | 42' |
III | 140' | (( |
(( |
(( |
47' | 35' |
IV | 110' | (( |
(( |
(( |
37' | 27' |
V | 90' | (( |
(( |
(( |
30' | 22' |
(B) Inner zone management. If trees can be harvested and removed from the inner zone because of surplus basal area consistent with the stand requirement, the harvest and removal of the trees must be undertaken consistent with one of two options:
(I) Option 1. Thinning from below. The objective of thinning is to distribute stand requirement trees in such a way as to shorten the time required to meet large wood, fish habitat and water quality needs. This is achieved by increasing the potential for leave trees to grow larger than they otherwise would without thinning. Thinning harvest under option 1 must comply with the following:
• Residual trees left in the combined core and inner zones must meet stand requirements necessary to be on a trajectory to desired future condition. See board manual section 7 for guidelines.
• Thinning must be from below, meaning the smallest dbh trees are selected for harvest first, then progressing to successively larger diameters.
• Thinning cannot decrease the proportion of conifer in the stand.
• Shade retention to meet the shade rule must be
confirmed by the landowner for any harvest inside of ((75))
seventy-five feet from the outer edge of bankfull width or
outer edge of CMZ, whichever is greater.
• The number of residual conifer trees per acre in the
inner zone will equal or exceed ((57)) fifty-seven.
Option 1. Thinning from below.
Site class |
RMZ width |
Core zone width
|
Inner zone width
|
Outer zone width
|
||
stream width ≤10' |
stream width >10' |
stream width ≤10' |
stream width >10' |
|||
I | 200' | 50' | 83' | 100' | 67' | 50' |
II | 170' | 50' | 63' | 78' | 57' | 42' |
III | 140' | 50' | 43' | 55' | 47' | 35' |
IV | 110' | 50' | 23' | 33' | 37' | 27' |
V | 90' | 50' | 10' | 18' | 30' | 22' |
(II) Option 2. Leaving trees closest to the water.
((Management option 2 applies only to riparian management
zones for site class I, II, and III on streams that are less
than or equal to 10 feet wide and RMZs in site class I and II
for streams greater than 10 feet wide. Harvest must comply
with the following:
• Harvest is not permitted within 30 feet of the core zone for streams less than or equal to 10 feet wide and harvest is not permitted within 50 feet of the core zone for streams greater than 10 feet wide;
• Residual leave trees in the combined core and inner zone must meet stand requirements necessary to be on a trajectory to desired future condition. See board manual section 7 for calculating stand requirements;
• A minimum of 20 conifers per acre, with a minimum 12-inch dbh, will be retained in any portion of the inner zone where harvest occurs. These riparian leave trees will not be counted or considered towards meeting applicable stand requirements nor can the number be reduced below 20 for any reason.
• Trees are selected for harvest starting from the outer most portion of the inner zone first then progressively closer to the stream.
• If (II) of this subsection results in surplus basal area per the stand requirement, the landowner may take credit for the surplus by harvesting additional riparian leave trees required to be left in the adjacent outer zone on a basal area-for-basal area basis. The number of leave trees in the outer zone can be reduced only to a minimum of 10 trees per acre.)) The objective of this option is to retain an RMZ width that will maintain current riparian functions. The stand must provide sufficient residual conifer trees in the combined core and inner zones to reach the target basal area of three hundred twenty-five square feet per acre at age one hundred forty.
Inner zone harvest may occur under option 2 if the projected future basal area within the combined width of the core and inner zones exceeds the target basal area. The combined core and inner zone width must be determined using the leaving trees closest to the water table below; the future basal area must then be calculated using the growth model program provided by the department. The model will produce a minimum inner zone floor width. (The minimum floor width extends outward from the outer edge of the fifty-foot core zone.)
Harvest is permitted under option 2 in the following order:
• If the projected basal area within the combined core and inner zones exceeds the target basal area, an even-age harvest may occur starting at the outermost portion of the inner zone and progressing to the inner zone floor edge.
In any portion of the inner zone where an even-age harvest method occurs, at least twenty conifer trees per acre with a minimum dbh of twelve inches must be retained. The basal area of these trees will be counted towards meeting applicable stand requirements.
• If the projected basal area within the combined core and inner zones still exceeds the target basal area, the conifer trees otherwise required to be left in the outer zone may be harvested on a basal-area-for-basal-area basis; however, only a maximum of ten conifer trees per acre may be harvested in the outer zone. (Tree counts, minimum size and placement of outer zone trees are specified below in (c) of this subsection.)
Option 2. Leaving trees closest to water.
Site class | Total RMZ width | ((
|
Combined core and inner zone width
|
Outer zone width
|
|||||
stream
width ≤10' |
stream
width ≤10' |
stream
width >10' |
stream
width >10' |
stream
width ≤10' |
stream
width >10' |
||||
Core and inner zone width | minimum
floor
(( |
Core and inner zone width | minimum
floor
(( |
||||||
(( |
|||||||||
I | 200' | (( |
(( |
(( |
(( |
(( |
66' | 66' | |
II | 170' | (( |
(( |
(( |
(( |
(( |
56' | 50' | |
III | 140' | (( |
(( |
(( |
(( |
(( |
46' | (( |
|
IV | 110' | 74' | 83' | 80' | 36' | 27' | |||
V | 90' | 61' | 68' | 29' | 22' |
(iii) Where the basal area components of the stand
requirement cannot be met within the sum of the areas in the
inner and core zone due to the presence of a stream-adjacent
parallel road in the inner or core zone, a determination must
be made of the approximate basal area that would have been
present in the inner and core zones if the road was not
occupying space in the core or inner zone and the shortfall in
the basal area component of the stand requirement. See
definition of "stream-adjacent parallel road" in WAC 222-16-010.
(A) Trees containing basal area equal to the amount determined in (iii) of this subsection will be left elsewhere in the inner or outer zone, or if the zones contain insufficient riparian leave trees, substitute riparian leave trees will be left within the RMZ width of other Type S or F Waters in the same unit or along Type Np or Ns Waters in the same unit in addition to all other RMZ requirements on those same Type S, F, Np or Ns Waters.
(B) When the stream-adjacent road basal area calculated
in (iii) of this subsection results in an excess in basal area
(above stand requirement) then the landowner may receive
credit for such excess which can be applied on a basal
area-by-basal area basis against the landowner's obligation to
leave trees in the outer zone of the RMZ of such stream or
other waters within the same unit, provided that the number of
trees per acre in the outer zone is not reduced to less than
((10)) ten trees per acre.
(C) When the basal area requirement cannot be met, as explained in (iii) of this subsection, the shortfall may be reduced through the implementation of an acceptable large woody debris placement plan. See board manual section 26 for guidelines.
(iv) If a harvest operation includes both yarding and harvest activities within the RMZ, all calculations of basal area for stand requirements will be determined as if the yarding corridors were constructed prior to any other harvest activities. If trees cut or damaged by yarding are taken from excess basal area, these trees may be removed from the inner zone. Trees cut or damaged by yarding in a unit which does not meet the basal area target of the stand requirements cannot be removed from the inner zone. Any trees cut or damaged by yarding in the core zone may not be removed.
(c) Outer zones. Timber harvest in the outer zone must
leave ((20)) twenty riparian leave trees per acre after
harvest. "Outer zone riparian leave trees" are trees that
must be left after harvest in the outer zone in Western
Washington. Riparian leave trees must be left uncut
throughout all future harvests:
Outer zone riparian leave tree requirements
Application | Leave tree spacing | Tree species | Minimum dbh required |
Outer zone | Dispersed | Conifer | 12" dbh or greater |
Outer zone | Clumped | Conifer | 12" dbh or greater |
Protection of sensitive features | Clumped | Trees representative of the overstory including both hardwood and conifer | 8" dbh or greater |
The ((20)) twenty riparian leave trees to be left can be
reduced in number under the circumstances delineated in
(c)(iv) of this subsection. The riparian leave trees must be
left on the landscape according to one of the following two
strategies. A third strategy is available to landowners who
agree to a LWD placement plan.
(i) Dispersal strategy. Riparian leave trees, which
means conifer species with a diameter measured at breast
height (dbh) of ((12)) twelve inches or greater, must be left
dispersed approximately evenly throughout the outer zone. If
riparian leave trees of ((12")) twelve inches dbh or greater
are not available, then the next largest conifers must be
left. If conifers are not present, riparian leave trees must
be left according to the clumping strategy in subsection (ii)
below.
(ii) Clumping strategy. Riparian leave trees must be left clumped in the following way:
(A) Clump trees in or around one or more of the following
sensitive features to the extent available within the outer
zone. When clumping around sensitive features, riparian leave
trees must be ((8)) eight inches dbh or greater and
representative of the overstory canopy trees in or around the
sensitive feature and may include both hardwood and conifer
species. Sensitive features are:
(I) Seeps and springs;
(II) Forested wetlands;
(III) Topographic locations (and orientation) from which leave trees currently on the site will be delivered to the water;
(IV) Areas where riparian leave trees may provide windthrow protection;
(V) Small unstable, or potentially unstable, slopes not of sufficient area to be detected by other site evaluations. See WAC 222-16-050 (1)(d).
(VI) ((Archeological)) Archaeological or historical sites
registered with the Washington state ((office)) department of
((archeology)) archaeology and historic preservation. See WAC 222-16-050 (1)(g); or
(VII) Sites containing evidence of Native American cairns, graves or glyptic records. See WAC 222-16-050 (1)(f).
(B) If sensitive features are not present, then clumps
must be well distributed throughout the outer zone and the
leave trees must be of conifer species with a dbh of ((12))
twelve inches or greater. When placing clumps, the applicant
will consider operational and biological concerns. Tree
counts must be satisfied regardless of the presence of
stream-adjacent parallel roads in the outer zone.
(iii) Large woody debris in-channel placement strategy.
A landowner may design a LWD placement plan in cooperation
with the department of fish and wildlife. The plan must be
consistent with guidelines in ((the)) board manual section 26.
The landowner may reduce the number of trees required to be
left in the outer zone to the extent provided in the approved
LWD placement plan. Reduction of trees in the outer zone must
not go below a minimum of ((10)) ten trees per acre. If this
strategy is chosen, a complete forest practices application
must include a copy of the WDFW approved hydraulics project
approval (HPA) permit.
(iv) Twenty riparian leave trees must be left after harvest with the exception of the following:
(A) If a landowner agrees to implement a placement strategy, see (iii) of this subsection.
(B) If trees are left in an associated channel migration zone, the landowner may reduce the number of trees required to be left according to the following:
(I) Offsets will be measured on a basal area-for-basal area basis.
(II) Conifer in a CMZ equal to or greater than ((6")) six
inches dbh will offset conifer in the outer zone at a
one-to-one ratio.
(III) Hardwood in a CMZ equal to or greater than ((10"))
ten inches dbh will offset hardwood in the outer zone at a
one-to-one ratio.
(IV) Hardwood in a CMZ equal to or greater than ((10"))
ten inches dbh will offset conifer in the outer zone at a
three-to-one ratio.
*(2) Western Washington protection for Type Np and Ns Waters.
(a) An equipment limitation zone is a ((30)) thirty-foot
wide zone measured horizontally from the outer edge of the
bankfull width of a Type Np or Ns Water where equipment use
and other forest practices that are specifically limited by
these rules. It applies to all perennial and seasonal
streams.
(i) On-site mitigation is required if any of the
following activities exposes the soil on more than ((10%)) ten
percent of the surface area of the zone:
(A) Ground based equipment;
(B) Skid trails;
(C) Stream crossings (other than existing roads); or
(D) Cabled logs that are partially suspended.
(ii) Mitigation must be designed to replace the equivalent of lost functions especially prevention of sediment delivery. Examples include water bars, grass seeding, mulching, etc.
(iii) Nothing in this subsection (2) reduces or eliminates the department's authority to prevent actual or potential material damage to public resources under WAC 222-46-030 or 222-46-040 or any related authority to condition forest practices notifications or applications.
(b) Sensitive site and RMZs protection along Type Np Waters. Forest practices must be conducted to protect Type Np RMZs and sensitive sites as detailed below:
(i) A ((50)) fifty-foot, no-harvest buffer, measured
horizontally from the outer edge of bankfull width, will be
established along each side of the Type Np Water as follows:
Required no-harvest, 50-foot buffers
on Type Np Waters.
Length of Type Np Water from the confluence of Type S or F Water | Length of 50' buffer required on Type Np Water (starting at the confluence of the Type Np and connecting water) |
Greater than 1000' | 500' |
Greater than 300' but less than 1000' | Distance of the greater of 300' or 50% of the entire length of the Type Np Water |
Less than or equal to 300' | The entire length of Type Np Water |
(ii) No timber harvest is permitted in an area within
((50)) fifty feet of the outer perimeter of a soil zone
perennially saturated from a headwall seep.
(iii) No timber harvest is permitted in an area within
((50)) fifty feet of the outer perimeter of a soil zone
perennially saturated from a side-slope seep.
(iv) No timber harvest is permitted within a ((56))
fifty-six-foot radius buffer patch centered on the point of
intersection of two or more Type Np Waters.
(v) No timber harvest is permitted within a ((56))
fifty-six-foot radius buffer patch centered on a headwater
spring or, in the absence of a headwater spring, on a point at
the upper most extent of a Type Np Water as defined in WAC 222-16-030(3) and 222-16-031.
(vi) No timber harvest is permitted within an alluvial fan.
(vii) At least ((50%)) fifty percent of a Type Np Waters'
length must be protected by buffers on both sides of the
stream (((2)) two-sided buffers). Buffered segments must be a
minimum of ((100)) one hundred feet in length. If an
operating area is located more than ((500)) five hundred feet
upstream from the confluence of a Type S or F Water and the
Type Np Water is more than ((1,000)) one thousand feet in
length, then buffer the Type Np Water according to the
following table. If the percentage is not met by protecting
sensitive sites listed in (b)(i) through (vii) of this
subsection, then additional buffers are required on the Type
Np Water to meet the requirements listed in the table.
Minimum percent of length of Type Np Waters to be buffered when more than 500 feet upstream from the confluence of a Type S or F Water
Total length of a Type Np Water upstream from the confluence of a Type S or F Water | Percent of length of Type Np Water that must be protected with a 50 foot no harvest buffer more than 500 feet upstream from the confluence of a Type S or F Water |
1000 feet or less | Refer to table in this subsection (i) above |
1001 - 1300 feet | 19% |
1301 - 1600 feet | 27% |
1601 - 2000 feet | 33% |
2001 - 2500 feet | 38% |
2501 - 3500 feet | 42% |
3501 - 5000 feet | 44% |
Greater than 5000 feet | 45% |
The landowner must select the necessary priority areas for additional 2-sided buffers according to the following priorities:
(A) Low gradient areas;
(B) Perennial water reaches of nonsedimentary rock with
gradients greater than ((20%)) twenty percent in the tailed
frog habitat range;
(C) Hyporheic and ground water influence zones; and
(D) Areas downstream from other buffered areas.
Except for the construction and maintenance of road crossings and the creation and use of yarding corridors, no timber harvest will be allowed in the designated priority areas. Landowners must leave additional acres equal to the number of acres (including partial acres) occupied by an existing stream-adjacent parallel road within a designated priority area buffer.
(c) None of the limitations on harvest in or around Type Np Water RMZs or sensitive sites listed in (b) of this subsection will preclude or limit:
(i) The construction and maintenance of roads for the purpose of crossing streams in WAC 222-24-030 and 222-24-050.
(ii) The creation and use of yarding corridors in WAC 222-30-060(1).
To the extent reasonably practical, the operation will both avoid creating yarding corridors or road crossings through Type Np Water RMZ or sensitive sites and associated buffers, and avoid management activities which would result in soil compaction, the loss of protective vegetation or sedimentation in perennially moist areas.
Where yarding corridors or road crossings through Type Np Water RMZs or sensitive sites and their buffers cannot reasonably be avoided, the buffer area must be expanded to protect the sensitive site by an area equivalent to the disturbed area or by providing comparable functions through other management initiated efforts.
Landowners must leave additional acres equal to the number of acres (including partial acres) occupied by an existing stream-adjacent parallel road within a Type Np Water RMZs or sensitive site buffer.
[Statutory Authority: RCW 76.09.040. 05-12-119, § 222-30-021, filed 5/31/05, effective 7/1/05. Statutory Authority: Chapter 34.05 RCW, RCW 76.09.040, [76.09.]050, [76.09.]370, 76.13.120(9). 01-12-042, § 222-30-021, filed 5/30/01, effective 7/1/01.]
OTS-1710.1
AMENDATORY SECTION(Amending WSR 05-12-119, filed 5/31/05,
effective 7/1/05)
WAC 222-30-021
*Western Washington riparian management
zones.
These rules apply to all typed waters on forest land
in Western Washington, except as provided in WAC 222-30-023. RMZs are measured horizontally from the outer edge of the
bankfull width or channel migration zone, whichever is
greater, and extend to the limits as described in this
section. See the board manual section 7 for riparian design
and layout guidelines.
*(1) Western Washington RMZs for Type S and F Waters have three zones: The core zone is nearest to the water, the inner zone is the middle zone, and the outer zone is furthest from the water. (See definitions in WAC 222-16-010.) RMZ dimensions vary depending on the site class of the land, the management harvest option, and the bankfull width of the stream. See tables for management options 1 and 2 below.
None of the limitations on harvest in each of the three zones listed below will preclude or limit the construction and maintenance of roads for the purpose of crossing streams in WAC 222-24-030 and 222-24-050, or the creation and use of yarding corridors in WAC 222-30-060(1).
The shade requirements in WAC 222-30-040 must be met regardless of harvest opportunities provided in the inner zone RMZ rules. See the board manual section 1.
(a) Core zones. No timber harvest or construction is allowed in the core zone except operations related to forest roads as detailed in subsection (1) of this section. Any trees cut for or damaged by yarding corridors in the core zone must be left on the site. Any trees cut as a result of road construction to cross a stream may be removed from the site, unless used as part of a large woody debris placement strategy or as needed to reach stand requirements.
(b) Inner zones. Forest practices in the inner zone must be conducted in such a way as to meet or exceed stand requirements to achieve the goal in WAC 222-30-010(2). The width of the inner zone is determined by site class, bankfull width, and management option. Timber harvest in this zone must be consistent with the stand requirements in order to reach the desired future condition targets.
"Stand requirement" means a number of trees per acre, the basal area and the proportion of conifer in the combined inner zone and adjacent core zone so that the growth of the trees would meet desired future conditions. The following table defines basal area targets when the stand is 140 years old.
Site Class | Desired future condition target basal area per acre (at 140 years) |
I | (( |
II | (( |
III | (( |
IV | (( |
V | (( |
(i) Hardwood conversion in the inner zone. When the existing stands in the combined core and inner zone do not meet stand requirements, no harvest is permitted in the inner zone, except in connection with hardwood conversion.
(A) The landowner may elect to convert hardwood-dominated stands in the inner zone to conifer-dominated stands. Harvesting and replanting shall be in accordance with the following limits:
(I) Conversion activities in the inner zone of any harvest unit are only allowed where all of the following are present:
• Existing stands in the combined core and inner zone do not meet stand requirements (WAC 222-30-021 (1)(b));
• There are fewer than 57 conifer trees per acre 8 inches or larger dbh in the conversion area;
• There are fewer than 100 conifer trees per acre larger than 4 inches dbh in the conversion area;
• There is evidence (such as conifer stumps, historical photos, or a conifer understory) that the conversion area can be successfully reforested with conifer and support the development of conifer stands;
• The landowner owns 500 feet upstream and 500 feet downstream of the harvest unit;
• The core and inner zones contain no stream adjacent parallel roads;
• Riparian areas contiguous to the proposed harvest unit are owned by the landowner proposing to conduct the conversion activities, and meet shade requirements of WAC 222-30-040 or have a 75-foot buffer with trees at least 40 feet tall on both sides of the stream for 500 feet upstream and 500 feet downstream of the proposed harvest unit (or the length of the stream, if less);
• If the landowner has previously converted hardwood-dominated stands, then post-harvest treatments must have been performed to the satisfaction of the department.
(II) In addition to the conditions set forth above, permitted conversion activities in the inner zone of any harvest unit are limited by the following:
• Each continuous conversion area is not more than 500 feet in length; two conversion areas will be considered "continuous" unless the no-harvest area separating the two conversion areas is at least half the length of the larger of the two conversion areas.
• Type S and F (Type 1, 2, or 3) Water: Up to 50% of the inner zone area of the harvest unit on one side of the stream may be converted provided that:
♦ The landowner owns the opposite side of the stream and the landowner's riparian area on the opposite bank meets the shade requirements of WAC 222-30-040 or has a 75-foot buffer of trees at least 40 feet tall or:
♦ The landowner does not own land on the opposite side of the stream but the riparian area on the opposite bank meets the shade requirements of WAC 222-30-040 or has a 75-foot buffer of trees at least 40 feet tall.
• Not more than 25% of the inner zone of the harvest unit on both sides of a Type S or F Water may be converted if the landowner owns both sides.
(III) Where conversion is allowed in the inner zone, trees within the conversion area may be harvested except that:
• Conifer trees larger than 20 inches dbh shall not be harvested;
• Not more than 10% of the conifer stems greater than 8 inches dbh, exclusive of the conifer noted above, within the conversion area may be harvested; and
• The landowner must exercise reasonable care in the conduct of harvest activities to minimize damage to all residual conifer trees within the conversion area including conifer trees less than 8 inches dbh.
(IV) Following harvest in conversion areas, the landowner must:
• Reforest the conversion area with conifer tree species suitable to the site in accordance with the requirements of WAC 222-34-010; and
• Conduct post-harvest treatment of the site until the conifer trees necessary to meet acceptable stocking levels in WAC 222-34-010(2) have crowns above the brush or until the conversion area contains a minimum of 150 conifer trees greater than 8 inches dbh per acre.
• Notify the department in writing within three years of the approval of the forest practices application for hardwood conversion, if the hardwood conversion has been completed.
(V) Tracking hardwood conversion. The purpose of tracking hardwood conversion is to determine if hardwood conversion is resulting in adequate enhancement of riparian functions toward the desired future condition while minimizing the short term impacts on functions. The department will use existing or updated data bases developed in cooperation with the Washington Hardwoods Commission to identify watershed administrative units (WAUs) with a high percentage of hardwood-dominated riparian areas and, thus have the potential for excessive hardwood conversion under these rules. The department will track the rate of conversion of hardwoods in the riparian zone: (1) Through the application process on an annual basis; and (2) at a WAU scale on a biennial basis as per WAC 222-30-120 through the adaptive management process which will develop thresholds of impact for hardwood conversion at the watershed scale.
(ii) Harvest options.
(A) No inner zone management. When the existing stands in the combined core and inner zone do not meet stand requirements, no harvest is permitted in the inner zone. When no harvest is permitted in the inner zone or the landowner chooses not to enter the inner zone, the width of core, inner and outer zones are as provided in the following table:
No inner zone management RMZ widths for Western Washington
Site Class | RMZ width | Core zone
width
|
Inner zone width
|
Outer zone width
|
||
stream width ≤10' |
stream width >10' | stream width ≤10' | stream width >10' | |||
I | 200' | 50' | 83' | 100' | 67' | 50' |
II | 170' | 50' | 63' | 78' | 57' | 42' |
III | 140' | 50' | 43' | 55' | 47' | 35' |
IV | 110' | 50' | 23' | 33' | 37' | 27' |
V | 90' | 50' | 10' | 18' | 30' | 22' |
(B) Inner zone management. If trees can be harvested and removed from the inner zone because of surplus basal area consistent with the stand requirement, the harvest and removal of the trees must be undertaken consistent with one of two options:
(I) Option 1. Thinning from below. The objective of thinning is to distribute stand requirement trees in such a way as to shorten the time required to meet large wood, fish habitat and water quality needs. This is achieved by increasing the potential for leave trees to grow larger than they otherwise would without thinning. Thinning harvest under option 1 must comply with the following:
• Residual trees left in the combined core and inner zones must meet stand requirements necessary to be on a trajectory to desired future condition. See board manual section 7 for guidelines.
• Thinning must be from below, meaning the smallest dbh trees are selected for harvest first, then progressing to successively larger diameters.
• Thinning cannot decrease the proportion of conifer in the stand.
• Shade retention to meet the shade rule must be confirmed by the landowner for any harvest inside of 75 feet from the outer edge of bankfull width or outer edge of CMZ, whichever is greater.
• The number of residual conifer trees per acre in the inner zone will equal or exceed 57.
Option 1. Thinning from below.
Site class |
RMZ width |
Core zone width
|
Inner zone width
|
Outer zone width
|
||
stream width ≤10' |
stream width >10' |
stream width ≤10' |
stream width >10' |
|||
I | 200' | 50' | 83' | 100' | 67' | 50' |
II | 170' | 50' | 63' | 78' | 57' | 42' |
III | 140' | 50' | 43' | 55' | 47' | 35' |
IV | 110' | 50' | 23' | 33' | 37' | 27' |
V | 90' | 50' | 10' | 18' | 30' | 22' |
(II) Option 2. Leaving trees closest to the water. Management option 2 applies only to riparian management zones for site class I, II, and III on streams that are less than or equal to 10 feet wide and RMZs in site class I and II for streams greater than 10 feet wide. Harvest must comply with the following:
• Harvest is not permitted within 30 feet of the core zone for streams less than or equal to 10 feet wide and harvest is not permitted within 50 feet of the core zone for streams greater than 10 feet wide;
• Residual leave trees in the combined core and inner zone must meet stand requirements necessary to be on a trajectory to desired future condition. See board manual section 7 for calculating stand requirements;
• A minimum of 20 conifers per acre, with a minimum
12-inch dbh, will be retained in any portion of the inner zone
where even-age harvest occurs. These riparian leave trees
will ((not)) be counted ((or considered)) towards meeting
applicable stand requirements ((nor can)). The number of
riparian leave trees cannot be reduced below 20 for any
reason.
• Trees are selected for harvest starting from the outer most portion of the inner zone first then progressively closer to the stream.
• If (II) of this subsection results in surplus basal area per the stand requirement, the landowner may take credit for the surplus by harvesting additional riparian leave trees required to be left in the adjacent outer zone on a basal area-for-basal area basis. The number of leave trees in the outer zone can be reduced only to a minimum of 10 trees per acre.
Option 2. Leaving trees closest to water.
Site class | RMZ width | Core zone
width
|
Inner zone width | Outer zone width
|
|||||
stream
width ≤10' |
stream
width ≤10' |
stream
width >10' |
stream
width >10' |
stream
width ≤10' |
stream
width >10' |
||||
minimum floor distance | minimum floor distance | ||||||||
(measured from outer edge of core zone) | (measured from outer edge of core zone) | (measured from outer edge of core zone) | (measured from outer edge of core zone) | ||||||
I | 200' | 50' | 84' | 30' | 84' | 50' | 66' | 66' | |
II | 170' | 50' | 64' | 30' | 70' | 50' | 56' | 50' | |
III | 140' | 50' | 44' | 30' | ** | ** | 46' | ** |
(iii) Where the basal area components of the stand
requirement cannot be met within the sum of the areas in the
inner and core zone due to the presence of a stream-adjacent
parallel road in the inner or core zone, a determination must
be made of the approximate basal area that would have been
present in the inner and core zones if the road was not
occupying space in the core or inner zone and the shortfall in
the basal area component of the stand requirement. See
definition of "stream-adjacent parallel road" in WAC 222-16-010.
(A) Trees containing basal area equal to the amount determined in (iii) of this subsection will be left elsewhere in the inner or outer zone, or if the zones contain insufficient riparian leave trees, substitute riparian leave trees will be left within the RMZ width of other Type S or F Waters in the same unit or along Type Np or Ns Waters in the same unit in addition to all other RMZ requirements on those same Type S, F, Np or Ns Waters.
(B) When the stream-adjacent road basal area calculated in (iii) of this subsection results in an excess in basal area (above stand requirement) then the landowner may receive credit for such excess which can be applied on a basal area-by-basal area basis against the landowner's obligation to leave trees in the outer zone of the RMZ of such stream or other waters within the same unit, provided that the number of trees per acre in the outer zone is not reduced to less than 10 trees per acre.
(C) When the basal area requirement cannot be met, as explained in (iii) of this subsection, the shortfall may be reduced through the implementation of an acceptable large woody debris placement plan. See board manual section 26 for guidelines.
(iv) If a harvest operation includes both yarding and harvest activities within the RMZ, all calculations of basal area for stand requirements will be determined as if the yarding corridors were constructed prior to any other harvest activities. If trees cut or damaged by yarding are taken from excess basal area, these trees may be removed from the inner zone. Trees cut or damaged by yarding in a unit which does not meet the basal area target of the stand requirements cannot be removed from the inner zone. Any trees cut or damaged by yarding in the core zone may not be removed.
(c) Outer zones. Timber harvest in the outer zone must leave 20 riparian leave trees per acre after harvest. "Outer zone riparian leave trees" are trees that must be left after harvest in the outer zone in Western Washington. Riparian leave trees must be left uncut throughout all future harvests:
Outer zone riparian leave tree requirements
Application | Leave tree spacing | Tree species | Minimum dbh required |
Outer zone | Dispersed | Conifer | 12" dbh or greater |
Outer zone | Clumped | Conifer | 12" dbh or greater |
Protection of sensitive features | Clumped | Trees representative of the overstory including both hardwood and conifer | 8" dbh or greater |
The 20 riparian leave trees to be left can be reduced in number under the circumstances delineated in (c)(iv) of this subsection. The riparian leave trees must be left on the landscape according to one of the following two strategies. A third strategy is available to landowners who agree to a LWD placement plan.
(i) Dispersal strategy. Riparian leave trees, which means conifer species with a diameter measured at breast height (dbh) of 12 inches or greater, must be left dispersed approximately evenly throughout the outer zone. If riparian leave trees of 12" dbh or greater are not available, then the next largest conifers must be left. If conifers are not present, riparian leave trees must be left according to the clumping strategy in subsection (ii) below.
(ii) Clumping strategy. Riparian leave trees must be left clumped in the following way:
(A) Clump trees in or around one or more of the following sensitive features to the extent available within the outer zone. When clumping around sensitive features, riparian leave trees must be 8 inches dbh or greater and representative of the overstory canopy trees in or around the sensitive feature and may include both hardwood and conifer species. Sensitive features are:
(I) Seeps and springs;
(II) Forested wetlands;
(III) Topographic locations (and orientation) from which leave trees currently on the site will be delivered to the water;
(IV) Areas where riparian leave trees may provide windthrow protection;
(V) Small unstable, or potentially unstable, slopes not of sufficient area to be detected by other site evaluations. See WAC 222-16-050 (1)(d).
(VI) ((Archeological)) Archaeological or historical sites
registered with the Washington state ((office)) department of
((archeology)) archaeology and historic preservation. See WAC 222-16-050 (1)(g); or
(VII) Sites containing evidence of Native American cairns, graves or glyptic records. See WAC 222-16-050 (1)(f).
(B) If sensitive features are not present, then clumps must be well distributed throughout the outer zone and the leave trees must be of conifer species with a dbh of 12 inches or greater. When placing clumps, the applicant will consider operational and biological concerns. Tree counts must be satisfied regardless of the presence of stream-adjacent parallel roads in the outer zone.
(iii) Large woody debris in-channel placement strategy. A landowner may design a LWD placement plan in cooperation with the department of fish and wildlife. The plan must be consistent with guidelines in the board manual section 26. The landowner may reduce the number of trees required to be left in the outer zone to the extent provided in the approved LWD placement plan. Reduction of trees in the outer zone must not go below a minimum of 10 trees per acre. If this strategy is chosen, a complete forest practices application must include a copy of the WDFW approved hydraulics project approval (HPA) permit.
(iv) Twenty riparian leave trees must be left after harvest with the exception of the following:
(A) If a landowner agrees to implement a placement strategy, see (iii) of this subsection.
(B) If trees are left in an associated channel migration zone, the landowner may reduce the number of trees required to be left according to the following:
(I) Offsets will be measured on a basal area-for-basal area basis.
(II) Conifer in a CMZ equal to or greater than 6" dbh will offset conifer in the outer zone at a one-to-one ratio.
(III) Hardwood in a CMZ equal to or greater than 10" dbh will offset hardwood in the outer zone at a one-to-one ratio.
(IV) Hardwood in a CMZ equal to or greater than 10" dbh will offset conifer in the outer zone at a three-to-one ratio.
*(2) Western Washington protection for Type Np and Ns Waters.
(a) An equipment limitation zone is a 30-foot wide zone measured horizontally from the outer edge of the bankfull width of a Type Np or Ns Water where equipment use and other forest practices that are specifically limited by these rules. It applies to all perennial and seasonal streams.
(i) On-site mitigation is required if any of the following activities exposes the soil on more than 10% of the surface area of the zone:
(A) Ground based equipment;
(B) Skid trails;
(C) Stream crossings (other than existing roads); or
(D) Cabled logs that are partially suspended.
(ii) Mitigation must be designed to replace the equivalent of lost functions especially prevention of sediment delivery. Examples include water bars, grass seeding, mulching, etc.
(iii) Nothing in this subsection (2) reduces or eliminates the department's authority to prevent actual or potential material damage to public resources under WAC 222-46-030 or 222-46-040 or any related authority to condition forest practices notifications or applications.
(b) Sensitive site and RMZs protection along Type Np Waters. Forest practices must be conducted to protect Type Np RMZs and sensitive sites as detailed below:
(i) A 50-foot, no-harvest buffer, measured horizontally from the outer edge of bankfull width, will be established along each side of the Type Np Water as follows:
Required no-harvest, 50-foot buffers
on Type Np Waters.
Length of Type Np Water from the confluence of Type S or F Water | Length of 50' buffer required on Type Np Water (starting at the confluence of the Type Np and connecting water) |
Greater than 1000' | 500' |
Greater than 300' but less than 1000' | Distance of the greater of 300' or 50% of the entire length of the Type Np Water |
Less than or equal to 300' | The entire length of Type Np Water |
(ii) No timber harvest is permitted in an area within 50 feet of the outer perimeter of a soil zone perennially saturated from a headwall seep.
(iii) No timber harvest is permitted in an area within 50 feet of the outer perimeter of a soil zone perennially saturated from a side-slope seep.
(iv) No timber harvest is permitted within a 56-foot radius buffer patch centered on the point of intersection of two or more Type Np Waters.
(v) No timber harvest is permitted within a 56-foot radius buffer patch centered on a headwater spring or, in the absence of a headwater spring, on a point at the upper most extent of a Type Np Water as defined in WAC 222-16-030(3) and 222-16-031.
(vi) No timber harvest is permitted within an alluvial fan.
(vii) At least 50% of a Type Np Waters' length must be protected by buffers on both sides of the stream (2-sided buffers). Buffered segments must be a minimum of 100 feet in length. If an operating area is located more than 500 feet upstream from the confluence of a Type S or F Water and the Type Np Water is more than 1,000 feet in length, then buffer the Type Np Water according to the following table. If the percentage is not met by protecting sensitive sites listed in (b)(i) through (vii) of this subsection, then additional buffers are required on the Type Np Water to meet the requirements listed in the table.
Minimum percent of length of Type Np Waters to be buffered when more than 500 feet upstream from the confluence of a Type S or F Water
Total length of a Type Np Water upstream from the confluence of a Type S or F Water | Percent of length of Type Np Water that must be protected with a 50 foot no harvest buffer more than 500 feet upstream from the confluence of a Type S or F Water |
1000 feet or less | Refer to table in this subsection (i) above |
1001 - 1300 feet | 19% |
1301 - 1600 feet | 27% |
1601 - 2000 feet | 33% |
2001 - 2500 feet | 38% |
2501 - 3500 feet | 42% |
3501 - 5000 feet | 44% |
Greater than 5000 feet | 45% |
The landowner must select the necessary priority areas for additional 2-sided buffers according to the following priorities:
(A) Low gradient areas;
(B) Perennial water reaches of nonsedimentary rock with gradients greater than 20% in the tailed frog habitat range;
(C) Hyporheic and ground water influence zones; and
(D) Areas downstream from other buffered areas.
Except for the construction and maintenance of road crossings and the creation and use of yarding corridors, no timber harvest will be allowed in the designated priority areas. Landowners must leave additional acres equal to the number of acres (including partial acres) occupied by an existing stream-adjacent parallel road within a designated priority area buffer.
(c) None of the limitations on harvest in or around Type Np Water RMZs or sensitive sites listed in (b) of this subsection will preclude or limit:
(i) The construction and maintenance of roads for the purpose of crossing streams in WAC 222-24-030 and 222-24-050.
(ii) The creation and use of yarding corridors in WAC 222-30-060(1).
To the extent reasonably practical, the operation will both avoid creating yarding corridors or road crossings through Type Np Water RMZ or sensitive sites and associated buffers, and avoid management activities which would result in soil compaction, the loss of protective vegetation or sedimentation in perennially moist areas.
Where yarding corridors or road crossings through Type Np Water RMZs or sensitive sites and their buffers cannot reasonably be avoided, the buffer area must be expanded to protect the sensitive site by an area equivalent to the disturbed area or by providing comparable functions through other management initiated efforts.
Landowners must leave additional acres equal to the number of acres (including partial acres) occupied by an existing stream-adjacent parallel road within a Type Np Water RMZs or sensitive site buffer.
[Statutory Authority: RCW 76.09.040. 05-12-119, § 222-30-021, filed 5/31/05, effective 7/1/05. Statutory Authority: Chapter 34.05 RCW, RCW 76.09.040, [76.09.]050, [76.09.]370, 76.13.120(9). 01-12-042, § 222-30-021, filed 5/30/01, effective 7/1/01.]