WSR 17-07-104
PROPOSED RULES
DEPARTMENT OF
LABOR AND INDUSTRIES
[Filed March 21, 2017, 10:08 a.m.]
Original Notice.
Preproposal statement of inquiry was filed as WSR 10-23-096.
Title of Rule and Other Identifying Information: Chapter 296-54 WAC, Safety standardsLogging operations.
Hearing Location(s): Department of Labor and Industries (L&I), 7273 Linderson Way S.W., Room S117, Tumwater, WA 98501, on May 15, 2017, at 9:00 a.m.
Date of Intended Adoption: August 1, 2017.
Submit Written Comments to: Tari Enos, P.O. Box 44620, Olympia, WA 98504-4620, email tari.enos@lni.wa.gov, fax (360) 902-5619, by 5:00 p.m. on May 22, 2017.
Assistance for Persons with Disabilities: Contact Tari Enos by May 1, 2017, at (360) 902-5541.
Purpose of the Proposal and Its Anticipated Effects, Including Any Changes in Existing Rules: The purpose of this proposal is to update the logging safety standards of chapter 296-54 WAC, Safety standardsLogging operations, per multiple petitions that were received from the Washington Contract Loggers Association (WCLA) in 2010 and 2014.
L&I started rule making in response to the petitions. However, in 2012, L&I put their rule-making efforts on hold to launch the logger safety initiative (LSI). The WCLA petitioned L&I again in 2014 to reopen rule-making efforts following the successful launch of the LSI program.
Also, references, formatting and minor housekeeping changes may be proposed throughout the chapter specified above.
NEW SECTIONS: WAC 296-54-520 Chain shot awareness and prevention, 296-54-52001 Chain shot awareness and prevention training, 296-54-52003 Cutting system inspection, 296-54-52005 Cutting system maintenance, 296-54-52007 Cutting system operation, and 296-54-99015 Appendix 6Sample chain shot training program.
AMENDED SECTIONS:
WAC 296-54-503 through 296-54-707.
Change "the employer" to "You" or "You must" where applicable.
Change bullets to letters or numbers where applicable.
Change numbering and lettering where applicable.
WAC 296-54-501 Scope and application.
Add clarifying language to first sentence to read: "This chapter establishes safety practices for all types of logging operations, log road construction and other similar activities.
Removed "forest activities using logging machinery and/or power saws regardless of the end use of the wood."
WAC 296-54-503 Variance.
Update zip code and P.O. Box number in address.
WAC 296-54-505 Definitions.
Delete all dashes from definitions and replace with periods.
Add definition of "chain shot," "chain shot danger zone or shot cone zone," and "spurious response attenuation."
Remove the following definitions: "Dapped," "dog line," "mainline train," "siwash," "speeder," "squirrel," and "squirrel tree."
WAC 296-54-507 Employer's responsibilities.
Remove "logging" from subsections (2) and (3).
WAC 296-54-511 Personal protective equipment (PPE).
Remove the word "design" from subsection (3).
Remove "All safety belts and attachments must meet the requirements of section 3 of ANSI A10.14-1975" from subsection (3).
Add new note to bottom of the section that reads: "The employer is not required to provide logging boots for employees. The cost of logging boots may be borne by employees. The employer must ensure, however, that logging boots as well as all PPE provided by the employer, are worn by employees and are in serviceable condition and meet the requirements of this subsection."
WAC 296-54-51110 Head protection.
Add clarifying language in opening paragraph of section to read: "You must provide, at no cost to the employee, and ensure that all employees wear a hard hat whenever there is a potential exposure to danger of flying or falling objects, unless the employees are protected by FOPs, cabs, or canopies meeting the requirements of this chapter."
Add clarifying language of subsection (1) to read: "Head protection (hard hats)["] must comply with any of the following consensus standards:
(a)
ANSI Z89.1-2009, "American National Standard for Industrial Head Protection;"
(b)
ANSI Z89.1-2003, "American National Standard for Industrial Head Protection;" or
(c)
ANSI Z89.1-1997, "American National Standard for Personnel Protection – Protective Headwear for Industrial Workers – Requirements."
Add new note to read: "Note: You may use protective helmets that do not meet these ANSI standards if you can demonstrate that they are equally effective as those constructed in accordance with the above ANSIs."
Remove original language of subsection (2), - language of previous subsection (3) is now (2).
WAC 296-54-51120 Eye and face protection.
Add new note to read: "Mesh type screen goggles or face shields, which conform to ANSI Z87.1, may be used while operating a chain saw or during chipping operations."
WAC 296-54-51140 Hand protection.
Add "or other rough materials" to subsection (1) – it was in previous versions of the rule and it was requested to put it back in the language.
WAC 296-54-51160 Leg protection.
Add clarifying language in first sentence of subsection (1) to read: "You must provide, at no cost to the employee, and ensure that each employee who operates a chain saw wears leg protection meeting the requirements of ASTM F1897 "American Society for Testing and Materials Standard Specification for Leg Protection for Chain Saw Users.""
WAC 296-54-51170 Foot protection.
Remove "logging" from subsection (1).
WAC 296-54-51190 Highly visible clothing.
Add clarifying language in subsection (1) to read: "Employees working on landings or in log sorting yards on or from the ground must wear at least one piece of highly visible equipment, whether it be their hard hat …"
WAC 296-54-513 Arrangement of work areas and emergency contact.
Add "logging" to subsections (8) and (9), so both subsections start with "Each logging worksite."
Remove "or UMS grid system coordinates" from subsection (9)(a).
WAC 296-54-515 Accident prevention program.
Replace "logging" with "workplace or" in subsection (1).
WAC 296-54-51510 Safety and health meetings.
Add clarifying language in subsection (1) to read: "You must hold safety and health meetings at least monthly."
Remove (a) and (b) from subsection (1).
Add new language to subsection (2): "A safety and health meeting must be held each time you move logging or timber felling operations to a new jobsite."
Move Note from bottom of section to just below subsection (2).
WAC 296-54-51520 First-aid training.
Add clarifying language in subsection (1) to read: "At logging worksites, each employee, including supervisors, must hold a valid certificate of first-aid and CPR training. New employees not holding a valid certificate of training must be trained within six months of being hired and they must be working on a crew where at least one person holding a valid certificate of first-aid and CPR training is present at all times."
Add clarifying language in subsection (2) to read: "At road construction and maintenance worksites, whenever two or more employees are present, a person or persons holding a valid certificate of first-aid and CPR training must be present at all times."
WAC 296-54-51530 First-aid kits.
Add clarifying language in subsection (1) to read: "You must provide first-aid kits at all worksites."
Remove (a), (b), (c) and (d) from subsection (1).
Add clarifying language in subsection (2) to read: "Worksite first-aid kits must contain the following minimum supplies at all times:"
Add clarifying language (o) in subsection (2) to read: "One stretcher or equivalent weather proof litter at any three or more person worksite, and at all logging sites."
Add letters (a) through (g) to supply list in subsection (3).
Remove "speeders" from subsection (3).
WAC 296-54-517 Lockout/tagout procedures.
Remove "logging" from subsections (1), (3)(b) and (5).
Remove "release from lockout/tagout" from subsection (4).
Remove "energy sources" from subsection (7).
WAC 296-54-521 Motor vehicles.
Add "s" to "provision" and "entrance" in subsection (3).
WAC 296-54-523 Inspection and repair of equipment and vehicles.
Remove "defective equipment" from beginning of section and add the word "defective" to subsection (1).
WAC 296-54-531 Truck roads.
Add clarifying language in subsection (3) to read: "For all portions of roads under your direct control, you must ensure that:"
WAC 296-54-537 Chain saws.
Add clarifying language in subsection (15) to read: "A chain saw must not be used to cut directly overhead in a manner where the operator could lose control of the saw, or that would cause limbs, chunks of bark or pieces of wood to fall on the operator."
WAC 296-54-539 Falling and buckingGeneral.
Add clarifying language in subsection (11) to read: "One worker must not fall a tree or danger tree when the assistance of another worker is necessary to minimize the risk of injury caused by overhead hazards, loose bark, or interlocked limbs, conditions of the tree, terrain or cutting conditions."
Add new subsection (12) that reads: "When manual falling or tree jacking, trees must not be felled directly uphill when the probability of the tree sliding back past the stump is likely."
WAC 296-54-53910 Falling and buckingFalling.
Add clarifying language in subsection (4) to read: "Before falling trees, cutters must:
(a)
Ensure that all personnel are out of reach of the tree; and
(b)
Ensure that all personnel are in the clear of logs, fallen trees, snags, or other trees that may be struck by the falling tree."
Remove exception from in between subsections (4) and (5).
Add new Figure 2 image that includes "Open Face Undercut."
Add new language in (C) under Figure 2 to read: "Open Face Undercut. Both cuts are made with the saw. The top and bottom face cuts generally form a 90 degree angle when completed. Works best on small diameter trees."
WAC 296-54-53930 Falling and buckingDanger trees.
Remove "must" and replace it with "should" in subsection (3).
WAC 296-54-53940 Falling and buckingSpringboards and tree jacking.
Add new subsection (10): "Trees must not be felled directly uphill when the probability of the tree sliding past the stump is likely."
WAC 296-54-541 Tree pulling.
Remove "Siwashing" from subsection (6) and update to: "Using a physical object such as a stump or tree in lieu of a block, in order to change tree pulling lead, is prohibited."
WAC 296-54-543 Mechanized falling.
Replace "shall" with "will" in subsection (3).
WAC 296-54-545 Climbing equipment and passline.
Add clarifying language in subsection (2)(c) to read: "A climbing rope (lanyard) made of a high-quality steel safety chain of 3/16-inch size or larger or a wire core rope."
WAC 296-54-54730 RiggingShackles.
Replace "be a maximum of" with "not be more than" in subsection (5).
Add clarifying language in subsection (6): "For example: 1-inch Extra Improved Plow Steel (EIPS) line requires a 1 1/8-inch shackle, 1-inch swaged line require 1 1/4 inch shackle."
WAC 296-54-54740 RiggingStraps.
Add new subsection (2): "Straps/chokers must be equivalently sized for the line they support, e.g., Extra Improved Plow Steel (EIPS) line requires EIPS straps or equivalent strength material, and swaged lines require swaged straps or equivalent strength material."
WAC 296-54-54750 RiggingBlocks.
Move "and" from after subsection (5)(b) to after (5)(a).
Change subsection (5)(c) to subsection (6).
WAC 296-54-54760 RiggingHanging blocks.
Add clarifying language in subsection (2)(a) to read: "Hanging the block in both eyes or Ds of the straps (threading eye through of wire rope straps is prohibited)."
WAC 296-54-557 Wire rope.
Remove subsection (2)(f) and reletter rest of section.
Add new exception above subsection (3) that reads: "EXCEPTION: Out-of-service requirements do not apply to chokers, grapple opening lines, tag lines, cat and skidder winch lines, and drop lines that are not used to move the carriage. However, an authorized, qualified person must thoroughly inspect these cables adhering to the requirements of WAC 296-54-54710 (1) and (3)."
WAC 296-54-55720 Wire ropeSplicing.
Add new note at the end of the section that reads: "Note: Unraveling 40 lays of cable on each side will give the required length of splice regardless of the diameter."
WAC 296-54-55730 Wire ropeAttaching end fastenings.
Add new subsection (5): "Wedge-type quick ferrules, such as "quick nub" must not be used as end fittings for guylines and skylines."
WAC 296-54-561 Guylines.
Remove letters (a) and (b) from subsection (5) and combine language.
Add exception between subsections (9) and (10) that reads: "Exception: It's acceptable to use the base of a tree/stump or ground conditions to change the lead of a guyline for the purpose of keeping the guyline properly positioned."
WAC 296-54-563 Guying tail/lift trees.
Change "below" to "above" in subsection (3)(b) which is describing what picture to refer to.
WAC 296-54-567 Rigging skylines.
Add "and hung in a manner to prevent excessive bight or fouling when tightened" to end of subsection (6)(b).
WAC 296-54-569 Anchoring.
Add clarifying language in subsection (7) to read: "When a standing tree is used as an anchor for guylines of portable spars, wood spars or towers:
(a)
The tree must be properly tied back if it is within reach of a work area, landing area or haul road;
(b)
The tree must be carefully chosen for strength;
(c)
The line or strap must be attached to the base of the tree; and
(d)
The tree must be adequately notched."
Add note below subsection (7) to read: "Note: The depth of the notch should not be any deeper than what is necessary to keep the line/strap from sliding up the tree."
WAC 296-54-573 Logging machinesGeneral.
Add new subsection (10): "Horns and travel alarms, which are part of the machine's original equipment, must be maintained in serviceable condition." Renumber the rest of the section.
WAC 296-54-57350 Logging machinesTractors and skidders.
Update "chocked" to "choked" in subsection (5)(c).
WAC 296-54-575 Landing area.
Remove "Landings must" from beginning subsection (1)(d).
Remove "when" from beginning of subsection (2) and start sentence with "During."
WAC 296-54-577 Yarding, skidding, landing.
Remove subsection (14) and renumber the rest of the section.
WAC 296-54-583 Loading logs.
Change "Employees must not be" to "No one is" in subsection (2).
WAC 296-54-58950 Log trucksWrappers and binders.
Add new language to subsection (1)(d)(ii) that reads: "When any log is over seventeen feet in length, the load must be secured by not less than three properly spaced wrappers. Log(s) loaded on top or in outside saddles of a load must not be transported unless secured by at least two wrapper chains or cables, one of which must be placed near each end of such log."
Add new language to subsection (10) that reads: "Wrappers must not be thrown over the load until personnel are in the clear."
WAC 296-54-601 Signals and signal systems.
Add clarifying language in subsection (6) to read: "A copy of the standard hand and whistle signals must be available at the worksite."
Add clarifying language in subsection (17) to read: "When the normal rigging crew configuration consists of two or more persons at the point where chokers are being set, at least two members of the rigging crew must carry transmitters for each signal and control system being operated where chokers are being set. Only one transmitter for each signal and control system is required if:"
WAC 296-54-604 Radio signaling permits.
Update zip code and P.O. Box in address.
WAC 296-54-605 Radio systems used for voice communication, activation of audible signals, or control of equipment.
Replace Figure 38 with a new image.
WAC 296-54-607 Radio signal systemsSpecifications and test procedures.
Remove definition of "Spurious response attenuation" from subsection (4) and moved it to the definitions section.
WAC 296-54-701 Wood spar trees.
Add clarifying language to first part of subsection (2): "The top of the tree must not extend more than …"
WAC 296-54-99003 Appendix 2Sample minimum lockout/tagout procedure.
Remove "logging" three times from the opening paragraphs of the section.
Add numbers to a list at the beginning of the section and under the new heading.
Add new heading that says: "Sample lockout/tagout procedures."
REPEALED SECTIONS: WAC 296-54-595 Transporting crews, 296-54-59510 Speeders used to transport crews, 296-54-59520 Trailers used to transport crews, 296-54-597 Railroads, 296-54-59710 Railroad construction and maintenance, 296-54-59720 Railroad operations, and 296-54-59730 Railroad maintenanceLoading or unloading.
Reasons Supporting Proposal: To ensure the logging rules are up-to-date with the technology of the industry to keep workers and employers safe while on the job.
Statutory Authority for Adoption: RCW 49.17.010, 49.17.040, 49.17.050, and 49.17.060.
Statute Being Implemented: Chapter 49.17 RCW.
Rule is not necessitated by federal law, federal or state court decision.
Name of Proponent: L&I, governmental.
Name of Agency Personnel Responsible for Drafting: Chris Miller, Tumwater, Washington, (360) 902-5516; Implementation and Enforcement: Anne Soiza, Tumwater, Washington, (360) 902-5090.
No small business economic impact statement has been prepared under chapter 19.85 RCW. A small business economic impact statement is not required for this rule making pursuant to RCW 19.85.030 (1)(a) as the department determined the rule will not result in or impose more than minor costs.
A cost-benefit analysis is required under RCW 34.05.328. A preliminary cost-benefit analysis may be obtained by contacting Tari Enos, P.O. Box 44620, Olympia, WA 98504, phone (360) 902-5541, fax (360) 902-5619, email tari.enos@lni.wa.gov.
March 21, 2017
Joel Sacks
Director
AMENDATORY SECTION (Amending WSR 01-11-038, filed 5/9/01, effective 9/1/01)
WAC 296-54-501 Scope and application.
This chapter establishes safety practices for all types of logging operations, log road construction and other ((forest activities using logging machinery and/or power saws regardless of the end use of the wood)) similar activities. This chapter does not apply to log handling at sawmills, plywood mills, pulp mills, or other manufacturing operations governed by specific safety standards. This chapter provides minimum safety requirements for the logging industry. The logging industry is also covered by the general safety standards, chapter 296-24 WAC; occupational health standards, chapter 296-62 WAC; the safety and health core rules, chapter 296-800 WAC; or others that may apply. Chapter 296-52 WAC, which covers the possession, handling and use of explosives, applies when explosives are used in logging operations.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-503 Variance.
If ((an employer)) you find((s)) it impractical to comply with specific requirements of this chapter, the department may permit a variation from the requirements. However, ((the employer)) you must still provide equal protection by substitute means. To request a variance, write to:
WISHA Services Division—Variance Request
Department of Labor & Industries
P.O. Box ((44648)) 44650
Olympia, WA ((98504-4648)) 98504-4650
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-505 Definitions.
A-frame(( - )). A structure made of two independent columns fastened together at the top and separated by a reasonable width at the bottom to stabilize the unit from tipping sideways.
An operation(( - )). Any place where logging or log related activities are taking place.
Approved(( - )). Approved by the department of labor and industries.
Arch(( - )). Any device attached to the back of a vehicle and used for raising one end of logs to facilitate movement.
Authorized person(( - )). A person approved or assigned by the employer to perform a specific type of duty(s) or to be at a specific location at a certain time(s).
Backcut (felling cut)(( - )). The cut in a felling operation made on the opposite side from the undercut.
Backline(( - )). The portion of the haulback that runs between the spar/spar tree and the corner block.
Ballistic nylon(( - )). A nylon fabric of high tensile properties designed to provide protection from lacerations.
Barrier(( - )). A fence, wall or railing to prevent passage or approach.
Base of tree(( - )). That portion of a natural tree not more than three feet above ground level.
Bight of the line(( - )). A hazardous zone created by running lines under tension. Any section of a line between the ends.
Binder(( - )). A hinged lever assembly for connecting the ends of a wrapper to tighten the wrapper around the load of logs or materials.
Boomboat(( - )). Any boat used to push or pull logs, booms, bundles, or bags, in booming ground operations.
Boomscooter(( - )). A small boat, usually less than fourteen feet in length, equipped with an outboard motor, having directional pushing capabilities of 360 degrees.
Brailing(( - )). When tiers of logs, poles, or piles are fastened together with a type of dogline and the ends of the side members are then fastened together for towing.
Brow log(( - )). A log or a suitable substitute placed parallel to any roadway at a landing or dump to protect the carrier and facilitate the safe loading or unloading of logs, timber products, or materials.
Buck(( - )). Means the process of severing a tree into sections (logs or bolts).
Butt(( - )). The bottom of the felled part of a tree.
Butt welding(( - )). The practice of welding something end to end.
Cable tree thinning(( - )). The selective thinning of a timber stand using mobile yarding equipment specifically designed or adapted for the purpose. Cable tree thinning includes skyline, slackline, or modified slackline, overhead cable systems.
Cable yarding(( - )). The movement of felled trees or logs from the area where they are felled to the landing on a system composed of a cable suspended from spars and/or towers. The trees or logs may be either dragged across the ground on the cable or carried while suspended from the cable.
Chain shot. When the saw chain breaks, when using a mechanical timber harvester or processor, fragments or pieces are projected with tremendous force, and can travel a distance greater than 250 feet.
Chain shot danger zone or shot cone zone. The area included within 15 degrees on either side of the guide bar and up to a distance of at least 250 feet.
Chock(( - )). A block, often wedge shaped, which is used to prevent movement; e.g., a log from rolling, a wheel from turning.
Choker(( - )). A length of wire rope with attachments for encircling the end of a log to be yarded.
Chunking(( - )). To clear nonusable material from a specified area.
Cold deck(( - )). A pile of yarded logs left for future removal.
Competent person(( - )). One who is capable of identifying hazards in the surroundings or working conditions which are unsanitary, hazardous or dangerous.
Corner block(( - )). The first block the haulback passes through on its way to the tail block.
Crotch line(( - )). Two short lines attached to the same ring or shackle, used for loading or unloading.
Cutter(( - )). An employee whose primary job is to fall, buck, or limb trees before they are moved to the landing area.
Danger trees(( - )). Any tree of any height, dead or alive, that presents a hazard to workers because of rot, root, stem or limb damage, lean, or any other observable condition created by natural process or man-made activity.
((Dapped - A notch in a timber for receiving part of another timber.))
DBH(( - )). Diameter at breast height.
Deadman(( - )). Buried log or other object used as an anchor.
Debark(( - )). To remove bark from trees or logs. Debark generally denotes mechanical means as opposed to manual peeling.
Deck(( - )). A stack of trees or logs.
Designated person(( - )). An employee who has the requisite knowledge, training, and experience to perform specific duties.
Directional falling(( - )). A mechanical means to control the direction of falling timber.
((Dog line - Type of line used to fasten logs or timber products together by the use of dogs.))
Domino felling(( - )). The partial cutting of multiple trees which are left standing and then pushed over with a pusher tree.
Donkey(( - )). Any machine with a series of drums used to yard logs.
Double ended logs(( - )). Two logs end to end on the same lay.
Drop zone(( - )). The area where the helicopter delivers logs from the logging site.
Droplines(( - )). A short line attached to the carriage or carriage block which is used as an extension to the main line.
Drum(( - )). A mechanical device on which line is spooled or unspooled.
Dry land storage(( - )). Decks of logs stored for future removal or use.
Dutchman(( - )).
(()) (a) A block used to change direction of line lead (sideblocking).
(()) (b) A method used to pull a tree against its lean by leaving a section of the undercut on one corner of the face. The portion left consists of a single saw kerf in one side of the face, with the face completely removed on the opposite side of the face cut. A single saw kerf must never extend completely across the stump.
Experienced person(( - )). A person who has been trained and has participated in the subject process for a period of time long enough to thoroughly acquaint the person with all facets of the process.
F.O.P.S.(( - )) Falling object protective structure.
Fair lead(( - )). Sheaves, rolls, or a combination thereof arranged to receive a line coming from any direction for proper line spooling on to a drum.
Fell (fall)(( - )). To cut down trees.
Feller (faller)(( - )). An employee who fells trees.
Front end loader(( - )). A mobile machine mounted on a wheeled or tracked chassis, equipped with a grapple, tusk, bucket, or fork-lift device, and employed in the loading, unloading, stacking, or sorting of logs or materials.
Grounded(( - )). The placement of a component of a machine on the ground or on a device where it is firmly supported. Grounded may also relate to the placement of a tree on the ground or a method to dissipate static or electrical charges.
Guarded(( - )). Covered, shielded, fenced, enclosed, or otherwise protected by means of suitable enclosures, covers, casings, shields, troughs, railings, screens, mats, or platforms, or by location, to prevent injury.
Guard rail(( - )). A railing to restrain a person.
Guyline(( - )). A line used to support or stabilize a spar, tail/lift tree, intermediate support tree or equipment. A guyline is considered a standing line.
Gypsy drum(( - )). A mechanical device wherein the line is not attached to the drum and is manually spooled to control the line movement on and off the drum.
Haulback(( - )). A line used to pull the buttrigging and mainline to the logs to be yarded.
Haulback block(( - )). Any block the haulback line passes through including the corner block and tailblock.
Hay rack(( - )).
(()) (a) A type of loading boom where two tongs are used and logs are suspended.
(()) (b) A transporting vehicle with multiple sets of bunks attached to a rigid frame usually used for hauling logs.
Haywire(( - )). See strawline.
Hazardous falling area(( - )). The area within a circle centered on the tree being felled and having a radius not less than twice the height of that tree.
Head tree(( - )). The tree where yarding and/or loading takes place. (See spar)
Heel boom(( - )). A type of loading boom where one tong is used and one end of the log is pulled up against the boom.
High lead(( - )). A system of logging wherein the main line is threaded through the main line block, which is attached near the top of the spar, to obtain a lift of the logs being yarded.
High visibility colors(( - )). White, bright, or fluorescent colors that stand out from the surrounding background color so they are easily seen.
Hobo log and/or hitchhiker(( - )). A free or unattached log that is picked up by a turn and is transported with the turn.
Hooktender(( - )). The worker that supervises the method of moving the logs from the woods to the landing.
Hot deck(( - )). A landing where logs are being moved.
Hydraulic jack(( - )). A mechanical device, powered by internal pressure, used to control the direction in which a tree is to be felled.
In the clear(( - )). A position within the work area where the probability of hazardous contact with falling trees, moving logs, rootwads, chunks, material, rigging and equipment is minimized by distance from the hazards and/or use of physical barriers, such as stumps, trees, terrain or other objects providing protection.
Examples:
(()) (a) Back behind on the uphill side of the turn and out of reach of any upending logs.
(()) (b) Out of the bight.
(()) (c) In the logged off area.
(()) (d) In a position where movement will not be obstructed.
Intermediate support system(( - )). A system for supporting a loaded skyline in a support jack by one of the two following methods:
(()) (a) Double tree support - The skyline is suspended on a single piece of wire rope supported by two trees so that the load is shared between the two trees.
(()) (b) Single tree support - The skyline is suspended on a single piece of wire rope, single-eyed choker or double-eyed strap supported by a single tree. The support tree may be vertical or leaning.
Jackstrawed(( - )). Trees or logs piled in an unorderly manner.
Jaggers(( - )). Any projecting broken wire in a strand of cable.
Kerf(( - )). The part of timber products taken out by the saw teeth.
Knob(( - )). A metal ferrule attached to the end of a line.
Landing(( - )). Any place where logs are laid after being yarded, awaiting subsequent handling, loading, and hauling.
Landing chute(( - )). The head of the skid trail or road where the logs are temporarily placed before handling, loading and hauling.
Lay(( - )).
(()) (a) The straight-line distance it takes a strand of wire rope to make one complete spiral around the core of a rope.
(()) (b) The position of a log in a pile, on a load, or in the fell and bucked.
Limbing(( - )). To cut branches off felled or standing trees.
Loading boom(( - )). Any structure projecting from a pivot point to guide a log when lifted.
Lodged tree (hung tree)(( - )). A tree leaning against another tree or object which prevents it from falling to the ground.
Log(( - )). A tree segment suitable for subsequent processing into lumber, pulpwood, or other wood products, including, but not limited to, poles, piling, peeler blocks, sections and/or bolts.
Log bronco(( - )). A sturdily built boat usually from twelve to twenty feet in length, used to push logs or bundles of logs in a generally forward direction in booming and rafting operations.
Log dump(( - )). A place where logs are removed from transporting equipment. It may be either dry land or water, parbuckled over a brow log or removed by machine.
Log stacker(( - )). A mobile machine mounted on a wheeled or tracked chassis, equipped with a frontally mounted grapple, tusk, or forklift device, and employed in the loading, unloading, stacking, or sorting of logs.
Logging machine(( - )). A machine used or intended for use to yard, move, or handle logs, trees, chunks, trailers, and related materials or equipment.
Note:
A self-loading log truck is only considered a logging machine when in use for loading and unloading.
Note:
A helicopter is not considered a logging machine.
Logging operations(( - )). Operations associated with felling and/or moving trees, logs, veneer bolts, poles, pilings, and other forest products from the stump to the point of delivery. Such operations are such, but not limited to, marking, felling, bucking, limbing, debarking, chipping, yarding, loading, unloading, storing, and the transporting of machines, equipment and personnel from one site to another.
Long sticks(( - )). An overlength log or tree length that creates a hazard by exceeding the safe perimeters of the landing.
Machine(( - )). A piece of stationary or mobile equipment having a self-contained power plant, that is operated off-road and used for the movement of material. Machines include but are not limited to tractors, skidders, front-end loaders, scrapers, graders, bulldozers, rough terrain logging shovels, log stackers and mechanical felling devices, such as tree shears and feller-bunchers.
Mainline(( - )). The line attached to the buttrigging used to pull logs to the landing.
Mainline block(( - )). The block hung in the portable spar or tower through which the mainline passes.
((Mainline train - Any train that is made up for travel between the woods and log dump.))
Matchcutting(( - )). The felling of trees without using an undercut.
Mechanized falling(( - )). Falling of standing timber by a self-propelled mobile wheeled or tracked machine equipped with a shear or other powered cutting device.
Mechanized feller(( - )). Any such machine as described in WAC 296-54-541 and 296-54-543, and includes feller/bunchers and similar machines performing multiple functions.
Mechanized logging machine(( - )). A feller-buncher, single-grip harvester, processor, forwarder, clambunk, or log loader.
Mobile log loader(( - )). A self-propelled log loading machine mounted on wheels or tracks, incorporating a boom and employed in the loading or unloading of logs by means of grapples or tongs.
Mobile yarder(( - )). A logging machine mounted on wheels, tracks, or skids, incorporating a vertical or inclined spar, tower, or boom, employed in skyline, slackline, high lead or grapple overhead cable logging systems.
Molle(( - )). A single strand of wire rope rolled into a circle with six wraps. A molle can be used as a temporary method of connecting the eye splices of two lines. A molle is used in most pin shackles in place of a cotter key.
Must(( - )). The same as "shall" and is mandatory.
New job site(( - )). A location of operations when the loading station and/or the yarder or cutting operations are moved to a new area outside of the current sale or contracted unit.
Pass line(( - )). A small line threaded through a block at the top of the spar to assist the high climber.
Permissible (as applied to any device, equipment or appliance)(( - )). Such device, equipment, or appliance has the formal approval of the United States Bureau of Mines, American Standards Association, or National Board of Fire Underwriters.
Portable spar or tower(( - )). A movable engineered structure designed to be used in a manner similar to which a wood spar tree would be used.
Qualified person(( - )). A person, who by possession of a recognized degree, certificate, professional standing, or by extensive knowledge, training, and experience, has successfully demonstrated ability to solve or resolve problems relating to the subject matter, the work, or the project.
Rated capacity(( - )). The maximum load a system, vehicle, machine or piece of equipment was designed by the manufacturer to handle.
Reach(( - )). A steel tube or wood timber or pole connected to the truck and inserted through a tunnel on the trailer. It steers the trailer when loaded and pulls the trailer when empty.
Reload(( - )). An area where logs are dumped and reloaded or transferred as a unit to another mode of transportation.
Rollway(( - )). Any place where logs are dumped and they roll or slide to their resting place.
Root wad(( - )). The ball of a tree root and dirt that is pulled from the ground when a tree is uprooted.
R.O.P.S.(( - )) Roll over protection structure.
Rub tree(( - )). A tree used to guide a turn around an area.
Running line/running rope(( - )). Any moving line directly involved with the yarding of logs.
Safety factor(( - )). The ratio of breaking strength to a safe working strength or loading.
Safety glass(( - )). A type of glass that will not shatter when broken.
Sail block(( - )). A block hung inverted on the sail guy to hold the tong block in proper position.
Scaler(( - )). The person who measures the diameter and length of the logs, determines specie and grade, and makes deductions for footage calculations.
Serviceable condition(( - )). A state or ability of a tool, machine, vehicle or other device to operate as it was intended by the manufacturer to operate.
Shall(( - )). A requirement that is mandatory.
Shear log(( - )). A log placed in a strategic location to divert passage of objects.
Shore skids(( - )). Any group of timbers spaced a short distance apart on which logs are rolled.
Should(( - )). Means recommended.
Signal person(( - )). The person designated to give signals to the machine operator.
((Siwash - To change the lead of a line with a physical object such as a stump or tree instead of a block.))
Skidder(( - )). A machine or animal used to move logs or trees to a landing.
Skidding(( - )). Movement of logs or trees on the surface of the ground to the place where they are to be loaded.
Skidding line(( - )). The main haulage line from a carriage to which chokers are attached. Sometimes referred to a mainline.
Skyline(( - )). The line suspended between two points on which a block or carriage travels.
Slackline(( - )). A form of skyline where the skyline cable is spooled on a donkey drum and can be raised or lowered.
Slack puller(( - )). Any weight or mechanical device used to increase the movement of a line when its own weight is inadequate.
Slope (grade)(( - )). The increase or decrease in altitude over a horizontal distance expressed as a percentage. For example, change of altitude of 20 feet (6 m) over a horizontal distance of 100 feet (30 m) is expressed as a 20 percent slope.
Snag(( - )). A dead standing tree or a portion thereof. (See Danger tree)
Snorkel(( - )). A loading boom modified to extend its limitations for yarding.
Spar/spar tree(( - )). A tree or device (rigged for highlead, skyline or slackline yarding) used to yard logs by any method of logging.
((Speeder - A small self-powered vehicle that runs on a railroad track.))
Spike(( - )). A long heavy nail similar to a railroad spike.
Springboard(( - )). A board with an iron tip used by fallers to stand on while working above ground level.
Spring pole(( - )). A tree, segment of a tree, limb, or sapling which is under stress or tension due to the pressure or weight of another object.
Spurious response attenuation. A measure of the receiver's ability to discriminate between a desired signal to which it is resonant and an undesired signal at any other frequency to which it is also responsive.
Square lead(( - )). The angle of 90 degrees.
((Squirrel - A weight used to swing a boom when the power unit does not have enough drums to do it mechanically.
Squirrel tree - A topped tree, guyed if necessary, near the spar tree in which the counter balance (squirrel) of a tree rigged boom is hung.))
Standing line(( - )).
(()) (a) Guyline.
(()) (b) A nonoperating rope with end terminations to support a boom or mast.
Stiff boom(( - )). Two or more boom sticks wrapped together on which boom persons walk or work.
Strap(( - )). Any short piece of line with an eye or "D" in each end.
Strap socket or D(( - )). A socket with a closed loop arranged to be attached to the end of a line by the molten zinc, or an equivalent method. It is used in place of a spliced eye.
Strawline(( - )). A light cable used in rigging up, or in moving other cables or blocks. The smallest line on the yarder. (Mainline - Haulback line - Strawline.)
Strip(( - )). A definite location of timber on which one or more cutting crews work.
Swamping(( - )). The falling or cutting of brush around or along a specified place.
Swede connection(( - )). A line configuration made by wrapping two choker lines in the same direction around a tree or log connecting the line knobs to opposite line bells.
Swifter(( - )). A piece of equipment used to tie the side sticks of a log raft together to keep the raft from spreading.
Swing cut(( - )). An intentional dutchman left on one corner of an undercut or a backcut in which the holding wood on one side is cut through in conjunction with an intentional dutchman to achieve a desired lay for the tree being fell.
Tail block(( - )). A block used to guide the haulback line at the back corner of the yarding area.
Tail hold(( - )). An anchor used for making fast any line or block.
Tail/lift tree(( - )). The tree at the opposite end from the head tree on which the skyline or other type rigging is hung.
Tie back(( - )). To use a twister(s) (or similar system/device) that has a breaking strength equal to fifty percent of the breaking strength of the mainline or skyline whichever is greater. To secure or support one anchor by securing it to a second anchor(s) such as wrapping one stump and choking another.
Tie down(( - )). A chain, cable, steel strips or fiber webbing and binders attached to a truck, trailer or other conveyance as a means to secure loads and to prevent them from shifting or moving when they are being transported.
Tight line(( - )). When either the mainline or haulback are held and power is exerted on the other or when power is exerted on both at the same time.
Tong line block(( - )). The block hung in a boom through which the tong line operates.
Tongue(( - )). A device used to pull and/or steer a trailer.
Topping(( - )). Cutting off the top section of a standing tree.
Tower(( - )). (See portable spar or tower).
Tractor(( - )). A machine of wheel or track design used in logging.
Tractor logging(( - )). The use of any wheeled or tracked vehicle in the skidding or yarding of logs.
Transfer (as used in loading)(( - )). Changing of logs in a unit from one mode of transportation to another.
Tree jack(( - )). A grooved saddle of wood or metal rollers contained within two steel plates, attached to a tree with a strap, used as a guide for skyline, sail guy, or similar static line. It is also formed to prevent a sharp bend in the line.
Tree plates(( - )). Steel bars sometimes shaped as elongated J's, which are fastened near the top of a tree to hold guylines and prevent them from cutting into the tree when tightened. The hooks of the J are also used to prevent the mainline block strap from sliding down the tree.
Tree pulling(( - )). A method of falling trees in which the tree is pulled down with a line.
Tug(( - )). A boat, usually over twenty feet in length, used primarily to pull barges, booms of logs, bags of debris, or log rafts.
Turn(( - )). Any log or group of logs attached by some means to power and moved from a point of rest to a landing.
Twister(( - )). A line (usually small diameter wire rope "haywire") that supports a tailhold stump, guyline stump, or tree that does not appear to be strong enough. This is done by connecting the tailhold to another stump or tree opposite by wrapping the two with a line. This line is then tightened by placing a piece of large-diameter limb between the wrappings and twisting them together.
 
TWISTER ROPE
Undercut(( - )). A notch cut in a tree to guide the direction of the tree fall and to prevent splitting or kickback.
V-lead(( - )). A horizontal angle of less than ninety degrees formed by the projected lines of the mainline from the drum of the logging machine through the block or fairlead and the yarding log or turn.
Vehicle/crew bus(( - )). A car, bus, truck, trailer or semi-trailer owned, leased, or rented by the employer that is used for transportation of employees or movement of material.
WAC(( - )). Washington Administrative Code.
Waistline(( - )). That portion of the haulback running between the corner block and the tail block.
Winching(( - )). The winding of cable or rope onto a spool or drum.
Within the stakes(( - )). When one-half the log diameter is below the stake top.
Work areas(( - )). Any area frequented by employees in the performance of assigned or related duties.
Wrapper(( - )). A cable assembly or chain used to contain a load of logs.
Wrapper rack(( - )). Barrier used to protect a person while removing binders and wrappers from a loaded logging truck.
Yarder (donkey)(( - )). A machine with a series of drums used to yard logs.
Yarding(( - )). The movement of logs from the place they are felled to a landing.
AMENDATORY SECTION (Amending WSR 14-07-086, filed 3/18/14, effective 5/1/14)
WAC 296-54-507 Employer's responsibilities.
((The employer)) You must comply with the requirements of all safety and health regulations and must:
(1) Provide safety training for each employee.
(2) Take additional precautions to ensure safe ((logging)) operations when extreme weather or other extreme conditions create hazards. If the ((logging)) operation cannot be made safe, the work must be discontinued until safe to resume.
(3) Ensure that danger trees within reach of landings, rigging, buildings, or work areas are either fell before regular ((logging)) operations begin, or arrange work so that employees are not exposed to the related hazards.
(4) Develop and maintain a hazard communication program as required by WAC 296-901-140. The program must provide information to all employees about hazardous chemicals or substances to which they are exposed, or may become exposed, in the course of their employment.
(5) Ensure that intoxicating beverages and narcotics are prohibited on or near the worksite. ((The employer)) You must remove from the worksite any employee under the influence of alcohol or narcotics.
Note:
Narcotics do not include prescription drugs taken under a doctor's direction if the use does not endanger any employee.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-509 Employee's responsibility.
(1) Employees must coordinate and cooperate with ((the employer)) you and other employees in an attempt to eliminate accidents.
(2) Employees must be aware of and follow all safe practices that apply to their work.
(3) Employees should offer safety suggestions that may contribute to a safer work environment.
(4) Intoxicating beverages and narcotics must not be permitted or used by employees in or around the worksites. Employees under the influence of alcohol or narcotics must not be permitted on the worksite.
EXCEPTION:
This rule does not apply to employees taking prescription drugs and/or narcotics as directed by a physician if the use does not endanger the employee or others.
(5) Employees must conduct themselves in a workmanlike manner while on the worksite.
(6) Employees must make prompt report to their immediate supervisor of each industrial injury or occupational illness, regardless of the degree of severity.
AMENDATORY SECTION (Amending WSR 09-05-071, filed 2/17/09, effective 4/1/09)
WAC 296-54-511 Personal protective equipment (PPE).
(1) Protective equipment, including personal protective equipment for eyes, face, head, hearing and extremities, protective clothing, respiratory devices and protective shields and barriers, must be used, and maintained in a sanitary and reliable condition wherever it is necessary by reason of hazards of processes or environment, chemical hazards, radiological hazards, or mechanical irritants encountered in a manner capable of causing injury or impairment in the function of any part of the body through absorption, inhalation or physical contact.
(2) Personal protective equipment, including any personal protective equipment provided by an employee, must be maintained in a serviceable condition.
(3) ((Design.)) All personal protective equipment must be of safe design and construction for the work to be performed. ((All safety belts and attachments must meet the requirements of section 3 of ANSI A10.14-1975.))
(4) Personal protective equipment, including any personal protective equipment provided by an employee, must be inspected before initial use during each workshift. Defects or damage must be repaired or the unserviceable personal protective equipment must be replaced before work is commenced.
(5) Personal protective equipment required by this standard ((shall)) must be provided at no cost to the employee.
Note:
The employer is not required to provide logging boots for employees. The cost of logging boots may be borne by employees. The employer must ensure, however, that logging boots as well as all PPE provided by the employer, are worn by employees and are in serviceable condition and meet the requirements in subsection (5) of this section.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-51110 Head protection.
((The employer)) You must provide, at no cost to the employee, and ensure that all employees ((involved in the logging operation or any of its related activities wear head protection)) wear a hard hat whenever there is a potential exposure to danger of flying or falling objects, unless the employees are protected by FOPS, cabs, or canopies meeting the requirements of this chapter.
(1) ((Hard hats purchased after February 20, 1995, must meet the requirements of ANSI Z89.1-1986, "American National Standard for Personnel Protection—Protective Headwear for Industrial Workers—Requirements," or the employer must demonstrate that they are equally effective.)) Head protection (hard hats) must comply with any of the following consensus standards:
(a) ANSI Z89.1-2009, "American National Standard for Industrial Head Protection";
(b) ANSI Z89.1-2003, "American National Standard for Industrial Head Protection"; or
(c) ANSI Z89.1-1997, "American National Standard for Personnel Protection – Protective Headwear for Industrial Workers – Requirements."
Note:
You may use protective helmets that do not meet these ANSI standards if you can demonstrate that they are equally effective as those constructed in accordance with the above ANSI standards.
(2) ((Hard hats purchased before February 20, 1995, must meet the requirements of ANSI Z89.1-1969, "American National Standard Safety Requirements for Industrial Head Protection," or the employer must demonstrate that they are equally effective.
(3))) Hard hats must be maintained in serviceable condition.
AMENDATORY SECTION (Amending WSR 01-11-038, filed 5/9/01, effective 9/1/01)
WAC 296-54-51120 Eye and face protection.
((The employer)) You must provide, at no cost to the employee, and ensure that each employee wears:
(1) Eye protection meeting the requirements of WAC 296-800-160, where there is potential for eye injury from falling or flying objects; and
(2) Face protection meeting the requirements of WAC 296-800-160, where there is potential for facial injury such as, but not limited to, operating a chipper. An employee using a chain saw may use either eye or face protection.
Note:
The employee does not have to wear separate eye protection when the face protection also covers the eyes.
Note:
Mesh type screen goggles or face shields, which conform to ANSI Z87.1, may be used while operating a chain saw or during chipping operations.
AMENDATORY SECTION (Amending WSR 03-11-060, filed 5/19/03, effective 8/1/03)
WAC 296-54-51130 Hearing protection.
((The employer)) You must provide hearing protection when required by chapter 296-817 WAC, Hearing loss prevention (noise).
AMENDATORY SECTION (Amending WSR 06-07-142, filed 3/21/06, effective 5/1/06)
WAC 296-54-51140 Hand protection.
(1) ((The employer)) You must provide, and make sure that each employee handling wire rope or other rough materials uses((,)) hand protection that provides adequate protection from puncture wounds, cuts, and lacerations.
(2) Hand protection must be maintained in serviceable condition.
AMENDATORY SECTION (Amending WSR 05-20-055, filed 10/3/05, effective 12/1/05)
WAC 296-54-51150 Respiratory protection.
((The employer)) You must provide respiratory protection when required by chapter 296-842 WAC, Respirators.
AMENDATORY SECTION (Amending WSR 12-01-086, filed 12/20/11, effective 2/1/12)
WAC 296-54-51160 Leg protection.
(1) ((The employer)) You must provide, at no cost to the employee, and ensure that each employee who operates a chain saw wears leg protection ((constructed with cut-resistant material, such as ballistic nylon.)) meeting the requirements of ASTM F1897 "American Society for Testing and Materials Standard Specification for Leg Protection for Chain Saw Users." The leg protection must cover the full length of the thigh to the top of the boot on each leg to protect against contact with a moving chain saw.
EXCEPTION:
This requirement does not apply to an employee working aloft in trees when supported by climbing spurs and climbing belt, or when an employee is working from a vehicle-mounted elevating and rotating work platform meeting the requirements of chapter 296-869 WAC, Elevating work platforms.
(2) Leg protection must be maintained in serviceable condition.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-51170 Foot protection.
(1) Each employee must wear foot protection that covers and supports the ankle, such as heavy-duty ((logging)) boots.
(2) Each employee who operates a chain saw must wear cut resistant foot protection that will protect the employee against contact with a running chain saw.
For example:
Leather logging boots, insulated rubber pacs, and rubber boots with cut protection will meet the cut-resistant requirement of this section.
(3) All employees whose duties require them to walk on logs or boomsticks must wear sharp-calked boots, or the equivalent.
EXCEPTION 1:
When calks are ineffective because of ice, snow, or other conditions and other footwear does not provide suitable protection, employees must be prohibited from working on logs or boomsticks.
EXCEPTION 2:
The employer may allow employees to wear nonslip boots instead of calks when the nonslip boots provide greater employee protection than calks (such as at scaling stations, log sorting yards, etc.). The nonslip boots must still provide firm ankle support and secure footing.
(4) Foot protection must be maintained in serviceable condition.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-51190 Highly visible clothing.
(1) Employees working on landings or in log sorting yards on or from the ground, must wear at least one piece of highly visible equipment, whether it be their hard hat((s)), yellow or orange vests, or other similarly colored garments, to make employees more visible to equipment operators.
Note:
The department recommends that hard hats and vests or outer garments be luminous or reflective.
(2) An employee working as a flagger must wear a hard hat and vest or other garment of high visibility colors. Warning vests and hard hats worn at night must be reflective.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-513 Arrangement of work areas and emergency contact.
(1) Employee work areas must be spaced and employee duties organized so the actions of one employee do not create a hazard for any other employee.
(2) Work areas must be assigned so that:
(a) Trees cannot fall into an adjacent occupied work area;
(b) The distance between work areas is at least two tree lengths of the trees being fell;
(c) The distance between work areas reflects the degree of slope, the density of the growth, the height of the trees, the soil structure and other hazards reasonably anticipated at the worksite; and
(d) A distance of more than two tree lengths is maintained between work areas on any slope where rolling or sliding of trees or logs is reasonably foreseeable.
(3) Each employee must be within visual, audible, or radio/telephone contact with another person who can assist in case of emergency.
(4) In any logging operation where cutting, yarding, or loading are performed, there must be at least two employees working as a team.
(5) Each employee must have visual or audible signal contact with another employee as often as this schedule requires:
(a) Cutters - 30 minutes.
(b) All other employees - 2 hours, which allows for making layouts, notching guyline stumps, etc., during normal work hours.
Exception:
The requirements for a two-person team and check-in schedule do not apply to operators of motor vehicles, mechanized logging machines, watchpersons or certain other jobs which, by their nature, are singular employee assignments. However, a procedure for checking the welfare of these employees during their working hours must be instituted and all employees so advised.
(6) Mechanics or other employees must not be assigned to work on equipment by themselves when there is a probability of a fall from elevated work locations or equipment. Also, if the work is of such nature that heavy parts require moving, or there is a probability that anything heavy could fall on the person, there must be another person in the immediate area to render assistance.
(7) ((The employer)) You must establish a method of checking the employees in from the woods at the end of each shift, including operators of all movable equipment. Each immediate supervisor must account for their crew.
(8) Each logging worksite must have at least one serviceable and operable two-way radio, phone, or radio/phone combination available to reach emergency service. Citizen band radios are permitted only as a secondary means of communication.
(9) Each logging worksite must have an emergency medical plan to ensure rapid emergency medical care for employees with major illnesses and injuries. The plan must be in writing and include the following:
(a) Township, range, and section numbers or latitude and longitude ((or UMS Grid System coordinates));
(b) Directions by road, or escort provisions to the site;
(c) Telephone number of emergency medical services; and
(d) Provisions for emergency vehicle(s) access, when working behind locked gate(s).
AMENDATORY SECTION (Amending WSR 06-07-142, filed 3/21/06, effective 5/1/06)
WAC 296-54-515 Accident prevention program.
(1) ((The employer)) You must develop a formal accident prevention program, tailored to the needs of the particular ((logging)) workplace or operation and to the type of hazards involved. The program must be implemented in a manner that is effective in practice.
(2) The accident prevention program must be in writing.
(3) The accident prevention program must cover at least the following elements:
(a) A safety training program that describes the employer's total safety program.
(b) How and when to report injuries;
(c) The location of first-aid supplies;
(d) Safe use, operation and maintenance of tools, machines and vehicles the employee uses or operates;
(e) How to report unsafe conditions and practices;
(f) The use and care of required personal protective equipment;
(g) An on-the-job review of the practices necessary to perform job assignments safely; and
(h) Recognition of safety and health hazards associated with the employee's specific work tasks, including using measures and work practices to prevent or control those hazards.
(4) ((The employer)) You must document and maintain current records of required training, including:
(()) (a) Who was trained;
(()) (b) The date(s) of the training; and
(()) (c) The signature of the trainer or ((the employer)) yours.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-51510 Safety and health meetings.
(1) ((The employer)) You must hold safety and health meetings at ((the following intervals:
(a) Each time the employer moves to a new job site; and
(b) Monthly after the initial job site meeting)) least monthly.
(2) A safety and health meeting must be held each time you move logging or timber felling operations to a new job site.
Note:
When moving to a new job site, site specific hazards should be identified and discussed during the prejob safety meeting.
(3) Safety and health meetings may be conducted individually, in crew meetings, in larger groups, or as part of other staff meetings.
(((3))) (4) Attendance and subject(s) must be documented.
((Note:
When moving to a new job site, site specific hazards should be identified and discussed during the prejob safety meeting.))
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-51520 First-aid training.
(1) At logging worksites, each employee, including supervisors, must ((receive or have received)) hold a valid certificate of first-aid and CPR training. New employees not holding a valid ((first-aid card)) certificate of training must be trained within ((a reasonable time, not to exceed six months from hiring)) six months of being hired and they must be working on a crew where at least one person holding a valid certificate of first-aid and CPR training is present at all times.
EXCEPTION:
Log truck drivers are not required to receive first-aid and CPR training if they are not involved with falling, yarding, loading, or processing logs.
(2) ((Each employee's first-aid and CPR training and/or certificate of training must be current.)) At road construction and maintenance worksites, whenever two or more employees are present, a person or persons holding a valid certificate of first-aid and CPR training must be present at all times.
(3) At least two persons holding a valid certificate of first-aid training must be present or available at all times in sorting yard operations.
(4) First-aid and CPR training must cover at least the following:
(a) The definition of first aid.
(b) Legal issues of applying first aid (Good Samaritan Laws).
(c) Basic anatomy.
(d) Patient assessment and first aid for the following:
(()) (i) Respiratory arrest.
(()) (ii) Cardiac arrest.
(()) (iii) Hemorrhage.
(()) (iv) Lacerations/abrasions.
(()) (v) Amputations.
(()) (vi) Musculoskeletal injuries.
(()) (vii) Shock.
(()) (viii) Eye injuries.
(()) (ix) Burns.
(()) (x) Loss of consciousness.
(()) (xi) Extreme temperature exposure (hypothermia/hyperthermia).
(()) (xii) Paralysis.
(()) (xiii) Poisoning.
(()) (xiv) Artificial ventilation.
(e) CPR.
(f) Applying dressings and slings.
(g) Treating strains, sprains, and fractures.
(h) Immobilizing injured persons.
(i) Handling and transporting injured persons.
(j) Treating bites, stings, or contact with poisonous plants or animals.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-51530 First-aid kits.
(1) ((The employer)) You must provide first-aid kits((:
(a) At each worksite where trees are being cut (e.g., falling, bucking, limbing);
(b) At each active landing/logging site; and
(c) In the absence of readily accessible first-aid supplies such as first-aid kits, first-aid stations, first-aid rooms or their equivalent, all transport vehicles, log trucks, speeders, road graders and similar equipment must be equipped with not less than a ten package first-aid kit; and
(d) The number of first-aid kits and the content of each kit must reflect the degree of isolation, the number of employees, and the hazards reasonably anticipated at the worksite.
(2) Following is the minimally acceptable number and type of required first-aid supplies to meet the requirements of subsection (1)(a) and (b) of this section.)) at all worksites.
(2) Worksite first-aid kits must contain the following minimum supplies at all times:
Note:
The contents of the first-aid kit listed should be adequate for small worksites of two or three employees. For larger or multiple logging operations conducted at the same location, the employer should provide additional first-aid kits or additional quantities of supplies in the first-aid kits.
(a) Gauze pads (at least 4 x 4 inches).
(b) Two large gauze pads (at least 8 x 10 inches).
(c) Box adhesive bandages (band-aids).
(d) One package gauze roller bandage at least 2 inches wide.
(e) Two triangular bandages.
(f) Wound cleaning agent such as sealed moistened towelettes.
(g) Scissors.
(h) At least one blanket.
(i) Tweezers.
(j) Adhesive tape.
(k) Latex gloves.
(l) Resuscitation equipment such as resuscitation bag, airway, or pocket mask.
(m) Two elastic wraps.
(n) Splint.
(o) One stretcher or equivalent weather proof litter at any three or more person worksite, and at all logging sites.
(3) Transport vehicles, log trucks, ((speeders)) and road graders must have at least the following number and type of first-aid supplies:
((10)) (a) Ten package kit.
((1)) (b) One pkg. adhesive bandages, 1" (16 per pkg.).
((1)) (c) One pkg. bandage compress, 4" (1 per pkg.).
((1)) (d) One pkg. scissors and tweezers (1 each per pkg.).
((1)) (e) One pkg. triangular bandage, 40" (1 per pkg.).
((1)) (f) One pkg. antiseptic soap or pads (3 per pkg.).
((5)) (g) Five pkgs. employer's choice.
(4) When six or more employees are generally being transported on any one trip, the first-aid kit must be increased in size following the requirements of subsection (2) of this section. Subsection (2)(h), (n) and (o) are optional.
(5) ((The employer)) You must maintain the contents of each first-aid kit in a serviceable condition.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-517 Lockout/tagout procedures.
(1) ((The employer)) You must establish and implement written procedures for lockout/tagout to prevent the accidental start up or release of stored energy of ((logging)) machinery that is shut down for repairs, maintenance, or adjustments.
(2) Lockout/tagout procedures must contain specific steps for:
(a) Shutting down, blocking, and securing machines to control hazardous energy;
(b) Locking and/or tagging out machinery; and
(c) Release from lockout/tagout.
(3) Lockout/tagout procedure details must include at least the following:
(a) Employees performing maintenance, repairs, or adjustments have knowledge of the hazardous energy to be controlled and the means to control the energy.
(b) ((Logging)) Machine shutdown.
(()) (c) Apply brakes, swing locks, etc.
(()) (d) Place the transmission in the manufacturer's specified park position.
(()) (e) Lower to the ground or secure each moving element such as, but not limited to, blades, booms, grapples, buckets, saws, and shears to prevent a release of stored energy.
(()) (f) Shut down machinery and ensure that a responsible person removes and maintains possession of the ignition/master key.
(()) (g) Engage hydraulic safety locks when applicable.
(()) (h) Before working on hydraulic or air systems, relieve pressure by bleeding tanks or lines and operate controls to dissipate residual stored energy (pressure).
(()) (i) Place lockout and/or tagout device.
(4) ((Release from lockout/tagout.)) Before lockout or tagout devices are removed and machinery is started, the work area must be inspected to ensure that all tools have been removed, guards are replaced, and employees are in the clear.
(5) ((The employer)) You must provide padlocks and/or tags for locking and/or tagging out ((logging)) machinery that are durable enough to withstand the environment.
(6) Tags must have a legend such as "do not start" or "do not operate." Tags must be placed so they are obvious to anyone attempting to operate the machinery.
Note:
In lockout, padlocks are commonly used to prevent access to ignition/master switches or battery disconnects.
(7) ((Energy sources.)) Stored or residual energy such as that in elevated machine members, rotating saws, hydraulic systems, air pressure and springs, must be dissipated or restrained by methods such as grounding, repositioning, blocking, chaining, bleeding down, etc.
(8) ((The employer)) You must provide training to ensure that the purpose and function of the lockout/tagout program are understood by employees performing maintenance, repairs, or adjustments covered by this section. This program must be reviewed at least annually and training provided as needed. This training may be accomplished through safety meetings.
Note:
See appendix 2 for a sample lockout/tagout program (energy control program).
AMENDATORY SECTION (Amending WSR 14-07-086, filed 3/18/14, effective 5/1/14)
WAC 296-54-519 Miscellaneous requirements.
(1) Spikes, drift bolts, nails, or other metal must not be left in any recoverable log.
(2) ((The employer)) You must provide and maintain portable fire extinguishers on each machine and vehicle.
(3) Machines, vehicles, and portable powered tools (unless diesel powered) must not be fueled while the motors are running.
Note:
See WAC 296-54-58130(3) for exceptions related to helicopters.
(4) Flammable liquids must be stored, handled, transported, and used according to the requirements of chapter 296-24 WAC, Part E, and the following:
(a) Flammable liquids must not be transported in the driver compartment or in any passenger-occupied area of a machine or vehicle.
(b) Flammable liquids, including chain-saw and diesel fuel, may be used to start a fire, if the employer ensures that in the particular situation its use does not create a hazard for an employee.
(5) Smoking is prohibited in battery charging areas and within fifty feet of all refueling operations. Precautions must be taken to prevent open flames, sparks, or electric arcs in battery charging or refueling areas.
(6) When charging batteries:
(a) The vent caps must be kept in place to avoid electrolyte spray;
(b) Caps must be functioning; and
(c) The battery (or compartment) cover(s) must be open to dissipate heat.
(7) Tools and other metallic objects must be kept away from the tops of uncovered batteries.
(8) Explosives and blasting agents must be stored, handled, transported, and used according to the requirements of chapter 296-52 WAC, Possession and handling of explosives.
NEW SECTION
WAC 296-54-520 Chain shot awareness and prevention.
"Chain shot" is the high velocity separation and ejection of a piece or pieces of cutting chain from the end of a broken chain in mechanized timber harvesting. Chain shot exposes both machine operators and bystanders to a risk of serious injury or death. Chain shot typically occurs near the drive end of the cutting system but can also come from the bar tip area.
A chain shot consists of two breaks in a chain. First, the loop of the chain breaks and forms two ends. One end moves past the drive sprocket or bar tip and is rapidly accelerated due to a whip-like motion of the chain end. The whip action causes the second break, releasing small parts at extremely high speed.
NEW SECTION
WAC 296-54-52001 Chain shot awareness and prevention training.
(1) Employees who will be working on or around any kind of machinery equipped with a hydraulic driven bar and chain are to receive chain shot awareness training appropriate to their job. This training must include:
(a) Clearance distances for workers around the machine. All bystanders and nonessential personnel should stay clear of the shot cone. Chain shot can travel in excess of 250 feet from the saw. See Illustration 1 for an explanation of the impact area for chain shot awareness.
(b) Personnel expected to maintain chains are to be trained in the proper repair, assembly, inspection, and sharpening as specified by the chain manufacturer.
(2) Operators are to be trained specifically on:
(a) When possible, position the saw bar so the chain shot cone is directed away from the operator and other personnel.
(b) How to properly inspect the cutting system and report any problems.
Note:
See WAC 296-54-99015 Appendix 6 – Sample chain shot training program.
Illustration 1: Shot Cone Zone
 
NEW SECTION
WAC 296-54-52003 Cutting system inspection.
(1) The cutting system must be inspected before initial use during each workshift. Inspections must include:
(a) The lubrication system for leaks or damage.
(b) The chain for cracks or worn/damaged parts.
(c) The bar for wear and straightness and ensure the tip is properly secured.
(d) Sprocket.
(e) Chain catcher if equipped; and
(f) Chain shot guard if equipped.
(2) You must repair defects or damage or the unserviceable machine must be replaced before beginning work.
NEW SECTION
WAC 296-54-52005 Cutting system maintenance.
(1) Sharpen chains to the manufacturer's specifications.
(2) Maintain proper bar and chain lubrication, making sure to use the right type and amount of lubricant.
(3) Replace the drive sprocket when it has excessive wear.
(4) Clean guide bar grooves and oil port holes regularly.
(5) To keep wear even the bar should be flipped regularly.
NEW SECTION
WAC 296-54-52007 Cutting system operation.
(1) When possible, keep the chain shot cone clear of the operator and other persons.
(2) Follow the chain manufacturer's recommendation for chain speed. "Boosting" or exceeding the manufacturer's recommendation is prohibited.
(3) Maintain proper chain tension.
AMENDATORY SECTION (Amending WSR 01-17-033, filed 8/8/01, effective 9/1/01)
WAC 296-54-521 Motor vehicles.
(1) The seats of each vehicle must be securely fastened.
(2) Each school bus type vehicle that will transport nine or more passengers must have a substantial barricade behind the driver. The barricade must extend from the floor to at least a level even with the top of the driver's head.
(3) Adequate provisions must be made for safe entrances and exits. Each vehicle must have mounting steps and handholds wherever it is necessary to prevent an employee injury when entering or leaving the vehicle.
(4) When equipment or tools are carried inside the vehicle, ((the employer)) you must provide and use racks, boxes, holsters or other means to transport tools so that a hazard is not created for any vehicle operator or passenger.
(5) No one may enter or exit any vehicle until the vehicle is completely stopped.
(6) Employees must keep all parts of the body within the vehicle.
(7) Heat and light must be available in the passenger area of the vehicle. Use of stoves in vehicles is prohibited.
(8) Vehicles designed to transport nine or more passengers must have an emergency exit that:
(a) Is at least six and one-half square feet in area, with the smallest dimension being at least eighteen inches;
(b) Is placed at the back of the vehicle or near the back on the side opposite the regular entrance; and
(c) Has an unobstructed route to and from the exit.
(9) When no fuel is transported in the crew vehicle, a minimum rated 5/BC dry chemical fire extinguisher must be kept in the passenger compartment. When fuel is transported on the crew vehicle according to subsection (12) of this section, a minimum rated 10/BC dry chemical fire extinguisher must be kept in the passenger compartment. The extinguishing agent must be nontoxic and preferably noncorrosive.
Note:
For additional requirements relating to portable fire extinguishers see WAC 296-800-300.
(10) Exhaust systems must be designed and maintained to eliminate the exposure of passengers to toxic agents.
(11) Operating and maintenance instructions must be available in each vehicle. Each vehicle operator and maintenance employee must comply with the operating and maintenance instructions.
(12) Fuel must be transported or stored only in approved safety containers. Enclosed areas where fuels are carried or stored must be vented so that a hazardous concentration of fumes cannot accumulate. All containers or drums must be properly secured to the vehicle while being transported. Commercially built pick-up or flatbed trucks with a maximum seating capacity of six persons may be used to carry fuel in or on the bed of such vehicles, if the fuel is not carried in the crew compartment. Van-type vehicles may be used to carry fuel only when a vapor-proof bulkhead is installed between the passenger compartment and storage compartment. A maximum of forty-two gallons of gasoline may be carried or stored in the compartment and each container must have a maximum capacity seven gallons.
(13) Motor vehicles used regularly to transport employees must be covered against the weather and equipped and operated according to applicable state of Washington motor vehicle laws.
(14) All operators of crew vehicles must be experienced drivers and have a valid operator's license for the class of vehicle being operated.
(15) Dump trucks must only be used in an emergency to transport workers and have adequate safety chains or locking devices that eliminate the possibility of the body of the truck being raised while employees are riding in the truck. "Emergency" means any unforeseen circumstances that call for immediate action when danger to life or danger from fire exists.
(16) An effective means of signaling must be provided for communication between the driver and the passengers being transported when they are in separate compartments.
(17) The passenger load limit of a crew vehicle must not exceed the seating capacity of the vehicle.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-523 Inspection and repair of equipment and vehicles.
((Defective equipment.)) (1) Defective equipment in need of repair must be reported to management as soon as possible and such equipment must not be used until repairs are completed if there is a possible hazard to safety of the operator or other employees.
(2) Each vehicle used to perform any logging operation must be inspected before initial use during each workshift. Defects or damage must be repaired or the unserviceable vehicle must be replaced before work is commenced.
(3) Each vehicle, machine and piece of equipment used to perform any logging operation must be maintained in serviceable condition.
AMENDATORY SECTION (Amending WSR 06-07-142, filed 3/21/06, effective 5/1/06)
WAC 296-54-527 Seat belts.
Each machine equipped with ROPS or FOPS and each vehicle (whether provided by the employee or ((the employer)) you) must meet the following requirements:
(1) A seat belt must be provided for each vehicle, vehicle occupant, and all machines equipped with ROPS.
Note:
An employer is not required to retrofit a vehicle that was not equipped with seat belts at the time of manufacture.
(2) Each employee must use the available seat belt while the vehicle or machine is being operated.
(3) Each employee must securely and tightly fasten the seat belt to restrain the employee within the vehicle or machine cab.
(4) Each machine seat belt must meet the requirements of the Society of Automotive Engineers Standard SAE J386, June 1985, "Operator Restraint Systems for Off-Road Work Machines." Seat belts need not be provided for equipment that is designed only for stand-up operations.
(5) Seat belts must not be removed from any vehicle or machine. ((The employer)) You must replace each seat belt that was removed from any vehicle or machine that was equipped with seat belts at the time of manufacture.
(6) Each seat belt must be maintained in a serviceable condition.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-529 Overhead electrical lines clearance.
One of the following conditions must exist in work areas where equipment or machines are operated near electrical distribution and transmission lines:
(1) The lines have been deenergized and visibly grounded at the point of work;
(2) Insulating barriers that are not a part of or an attachment to the equipment or machinery are erected to prevent physical contact with the lines; or
(3) All of the following requirements are met:
 
Line Voltage
Required minimum clearance between lines and any part of equipment or machine
(a)
50 kV or below
ten feet
(b)
over 50 kV
ten feet plus 0.4 inch for each 1 kV over 50 kV, or twice the length of the line insulator, but never less than ten feet
For equipment or machinery in transit with no load and any boom or extended equipment lowered:
(c)
50 kV or below
four feet
(d)
50-345 kV
ten feet
(e)
345-750 kV
sixteen feet
(4) Someone must be designated to observe proper clearance and to give timely warning for all operations where it is difficult for the operator to see well enough to maintain the clearance.
(5) All overhead wires ((shall)) must be considered energized unless the line owner or the electrical utility authorities ensure that it is not an energized line and has been visibly grounded.
(6) Special precautions must be taken to prevent trees from falling into power lines. ((The employer)) You must notify the power company immediately if a felled tree makes contact with any power line. Before falling any tree that appears will hit a power line, the employer must notify the power company. If a tree does contact a power line, all employees must remain clear of the area until the power company ensures that there is no electrical hazard.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-531 Truck roads.
(1) Haul road grades must not exceed 20 percent unless:
(a) Special equipment and safety measures are used to accommodate the steep grade; or
(b) The logging equipment or truck is specifically designed and approved by the manufacturer for operation on grades over twenty percent.
(2) Truck road surfaces must meet the following requirements:
(a) Truck roads are wide enough and even to ensure the safe operation of equipment.
(b) Hazards such as broken planking, deep holes, large rocks, logs, etc., that make equipment operation unsafe, must be immediately corrected.
(c) On blind curves, one of the following must be implemented:
(i) Truck roads are wide enough for two trucks to pass;
(ii) A signal system is maintained; or
(iii) Speed is limited so that the vehicle can be stopped in one-half the visible distance.
(3) For all portions of roads under ((the)) your direct control ((of the employer, the employer)), you must ensure that:
(a) All danger trees are fell a safe distance back from the roadway;
(b) Rocks that present a hazard are cleared from banks; and
(c) Brush and other materials that obstruct the view at intersections or on sharp curves are cleared.
(4) All bridge structures used in the logging operation must meet the following requirements:
(a) Structures are adequate to support the maximum imposed loads without exceeding the maximum safe working unit stresses;
(b) Bridges have an adequate number of reflectors to clearly define the entrance to the bridge;
(c) Structures are maintained in good condition and repair;
(d) Structures are inspected at least annually by a qualified authorized person; and
(e) A record maintained of each inspection must be available to a representative of the department on request.
(5) Shear rails must be installed on both outside edges of bridges. The shear rails must be securely fastened and made of material able to withstand the impact generated by contact with the wheels of a loaded vehicle. The top of shear rails must be at least fifteen inches above the bridge surface. Bridges in use before 1980 with outside shear rails a minimum of ten inches high or center shear rails at least five inches high are permissible until repairs are needed.
(6) ((The employer)) You must implement measures that minimize dust to the degree that visibility is sufficient to allow an operator to safely operate a vehicle. Vehicle operators must travel at a speed consistent with road conditions.
(7) Pneumatic-tired equipment must have fenders as described in the Society of Automotive Engineers Technical Report J321a.
(8) Employee(s) must be assigned to flag on roads or provide other equivalent protection where hazardous conditions are created from logging such as, but not limited to:
(a) Running wire rope lines or rigging across road grades, excluding guylines and standing skylines if lines remain a safe distance above the road to allow a vehicle to pass under; or
(b) The movement of logs, chunks, or debris across or suspended over road grades.
EXCEPTION:
Where there is no through traffic, such as on a dead end road or where the property owner's permission or proper authority is granted to close a section of road, warning signs and barricades may be used instead of flagger(s).
AMENDATORY SECTION (Amending WSR 06-07-142, filed 3/21/06, effective 5/1/06)
WAC 296-54-537 Chain saws.
(1) Operators must inspect chain saws daily to ensure that handles and guards are in place, and controls and other moving parts are functional.
(a) Each chain saw placed into initial service after February 9, 1995, must be equipped with a chain brake and, shall otherwise meet the requirements of ANSI B175.1-1991 "Safety Requirements for Gasoline-Powered Chain Saws" and the requirements of this chapter;
(b) Each chain saw placed into service before February 9, 1995, must be equipped with a protective device that minimizes chain saw kickback, i.e., reduced kickback bar, chains, bar tip guard, or chain brake;
(c) No chain saw kickback device shall be removed or otherwise disabled; and
(d) Chain saws must be operated and adjusted in accordance with the manufacturer's instructions.
(2) Saw pinching and subsequent chain saw kickback must be prevented by using wedges, levers, guidelines, and saw placement, or by undercutting.
(3) Chain saws must be:
(a) Shutoff while fueling;
(b) Fueled outdoors at least ten feet from anyone smoking or from other potential sources of ignition; and
(c) Started at least 10 feet (3 m) from the fueling area.
(4) Chain saws must have a positive means of stopping the engine.
(5) Unless the carburetor is being adjusted, the chain saw must be shut off before any adjustments or repairs are made to the saw, chain, or bar.
(6) Using a chain saw with a faulty clutch is prohibited.
(7) The bar must be handled only when the chain saw motor is shut off.
(8) The drive end of the chain saw bar must be guarded.
(9) The chain saw must have an automatic throttle control that will return the engine to idle speed when the throttle is released.
Note:
Idle speed is when the engine is running and the chain does not rotate on the bar.
(10) The chain saw must be started:
(a) With the chain brake engaged, unless the manufacturer prohibits; or
(b) On the ground, log or where otherwise firmly supported. Drop starting a chain saw is prohibited.
(11) A chain saw must be held with the thumbs and fingers of both hands encircling the handles during operation unless ((the employer)) you demonstrate((s)) that a greater hazard is posed by keeping both hands on the chain saw in a specific situation.
(12) The chain saw must be carried in a manner that will prevent operator contact with the cutting chain and muffler.
(13) The chain saw must be shut off or at idle before the faller starts to retreat.
(14) The chain saw must be shut down or the chain brake engaged whenever a saw is carried:
(a) Further than 50 feet (15.2 m); or
(b) Less than 50 feet if conditions such as, but not limited to, the terrain, underbrush, and slippery surfaces, may create a hazard for an employee.
(15) ((Using a chain saw to cut directly over head is prohibited.)) A chain saw must not be used to cut directly overhead in a manner where the operator could lose control of the saw, or that would cause limbs, chunks of bark or pieces of wood to fall on the operator.
(16) The chain saw operator must be certain of footing before starting to cut. The chain saw must not be used in a position or at a distance that could cause the operator to become off-balance, to have unsteady footing, or to relinquish a firm grip on the saw.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-539 Falling and buckingGeneral.
(1) ((The employer)) You must assign work areas so that:
(a) Trees cannot fall into an adjacent occupied work area;
(b) The distance between work areas is at least two tree lengths of the trees being fell (see Figure 1: Distance Between Work Areas);
 
Figure 1: Distance Between Work Area
(c) The distance between work areas reflects the degree of slope, the density of the growth, the height of the trees, the soil structure and other hazards reasonably anticipated at the worksite; and
(d) A distance of more than two tree lengths is maintained between work areas on any slope where rolling or sliding of trees or logs is reasonably foreseeable.
EXCEPTION:
This rule does not apply to a team of cutters working on the same tree.
(2) Before falling or bucking, conditions such as, but not limited to, snow and ice accumulation, the wind, the lean of tree, dead limbs, and the location of other trees, must be evaluated by the cutter and precautions taken so a hazard is not created for an employee. Accumulations of snow and ice that may create a hazard for an employee must be removed before beginning falling in the area, or the area must be avoided.
(3) Employees must not approach a cutter closer than two tree lengths of trees being felled until the cutter has acknowledged that it is safe to do so.
(4) A competent person, properly experienced in this type of work, must be placed in charge of falling and bucking operations. Inexperienced workers must not be allowed to fall timber, buck logs or windfalls unless working under the direct supervision of an experienced cutter.
(5) Trees must not be fell if the falling tree can strike any line in the logging operation and endanger workers.
(6) Before an employee falls or bucks any tree:
(a) A sufficient work area must be swamped;
(b) The cutter must plan and clear an escape path; and
(i) The escape path must extend diagonally away from the expected felling line unless such an escape path poses a greater hazard than an alternate escape path; and
(ii) An escape path must be used as soon as the tree or snag is committed to fall, roll, or slide.
(7) If a cutter has determined a tree cannot be safely fell, the work must stop until the cutter has conferred with a supervisor or an experienced cutter and determined the safest possible work method or procedure.
(8) The person in charge of cutting crews must regularly inspect the work of the cutting crews and is responsible to ensure the work is performed in a proper and safe manner.
(9) All cutters must carry or have in near proximity at all times:
(a) An axe or suitable tool for driving wedges;
(b) A minimum of two wedges;
(c) A whistle carried on the person; and
(d) A first-aid kit.
(i) The first-aid kit must contain at least two trauma bandages or equivalent absorbent gauze material and a means to secure the material in place.
(ii) First-aid supplies must be kept clean and dry.
(10) A flagperson(s) must be assigned on roads where hazardous conditions are created from falling trees. Where there is no through traffic, such as on a dead end road, warning signs or barricades may be used instead of a flagperson(s).
(11) ((A cutter must not fall a tree or danger tree alone when at least two cutters are necessary to minimize hazards.)) One worker must not fall a tree or danger tree when the assistance of another worker is necessary to minimize the risk of injury caused by overhead hazards, loose bark, or interlocked limbs, conditions of the tree, terrain or cutting conditions.
(12) When manual falling or tree jacking, trees must not be felled directly uphill when the probability of the tree sliding back past the stump is likely.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-53910 Falling and buckingFalling.
(1) Where felled trees are likely to roll and endanger workers, cutting must proceed from the bottom toward the top of the slope, and uphill from previously fell timber.
(2) A cutter must not be placed on a hillside immediately below another cutter or below other logging operations where there is probable danger.
(3) Cutters must be informed of the movement and location of other employees placed, passing, or approaching the vicinity of trees being fell.
(4) Before falling trees, cutters must ((give audible warning when falling trees, and)):
(a) ((Indicate the direction of fall;
(b))) Ensure that all ((employees)) personnel are out of reach of the tree; and
(((c))) (b) Ensure that all ((employees)) personnel are in the clear of logs, fallen trees, snags, or other trees that may be struck by the falling tree.
((EXCEPTION:
Audible warnings are not required when falling trees less than eighteen inches DBH, if the cutter has an unobstructed view of the entire area that could be affected by the tree being fell and is assured there is no one within the area.))
(5) While manual falling is in progress, all logging machines must be operated at least two lengths away from trees being manually fell.
EXCEPTION:
This provision does not apply to logging machines performing tree pulling operations or logging machines called upon by the cutter to ground hazard trees. All cutters must be notified of the logging machine's entrance into the area and all falling within two tree lengths of the logging machine must stop.
(6) Trees must be fell into the open whenever conditions permit.
(7) Cutters must not fall into another strip; trade leaners on the line.
(8) Knocking over trees larger than six inches in diameter in lieu of cutting is prohibited, except as provided in WAC 296-54-53910(9).
(9) Domino falling of trees, including danger trees, is prohibited. Domino falling does not include the falling of a single danger tree by falling another single tree into it.
(10) Undercuts large enough to safely guide trees and eliminate the possibility of splitting must be used on all trees over six inches DBH.
For example:
A tree with no perceptible lean, having an undercut depth of one-fourth of the diameter of the tree and a face opening equal to one-fifth of the diameter of the tree would meet the requirement.
(11) A cutter must place an adequate undercut and leave enough holding wood to ensure the tree will fall in the intended direction.
(12) The two cuts that form the undercut must not cross where they meet, except where a dutchman is required on either side of the cut.
(13) The undercut must not be made while other workers are in an area into which the tree could fall.
(14) A backcut must be made in each tree being fell.
(a) The backcut must be as level as possible;
(b) The backcut must leave enough hinge wood to hold the tree to the stump during most of its fall so that the hinge is able to guide the tree's fall in the intended direction; and
(c) The backcut must be above the level of the horizontal facecut to provide an adequate platform to prevent kickback.
EXCEPTION:
This requirement does not apply to open-faced falling where two angled facecuts are used instead of a horizontal facecut.
(d) In tree-pulling operations the backcut may be at or below the undercut hinge point.
(15) Cutting holding wood instead of using wedges is prohibited. Swing cuts are prohibited except by an experienced person.
(16) Trees with face cuts and/or backcuts must not be left standing unless all the following conditions are met:
(a) The cutter clearly marks the tree;
(b) Discontinues work in the hazardous area;
(c) Notifies all workers who might be endangered; and
(d) Takes appropriate measures to ensure that the tree is safely fell before other work is undertaken in the hazardous area.
(17) Undercuts and backcuts must be made at a height above the highest ground level to enable the cutter to safely begin the cut, control the tree, and have freedom of movement for a quick escape from a falling tree.
(18) Lodged trees must be clearly marked and identified by a predetermined method and all persons in the area must be instructed not to pass or work within two tree lengths of the trees except to ground them.
Note:
See Figure No. 2, for illustrations of undercuts.
(( 
 
)) 
 
FIGURE 2: UNDERCUTS
(A)
Conventional undercut. Can be made with parallel saw cut and axe diagonal cut or both cuts with the saw. Generally used on trees of small diameter.
(B)
Humboldt undercut. Leaves square-end log. Same as (A), except that waste is put on the stump.
(C)
Open face undercut. Both cuts are made with the saw. The top and bottom face cuts generally form a 90 degree angle when completed. Works best on small diameter trees.
(D)
Two parallel cuts with the saw. The material between the cuts is chopped out with an axe-adz (pulaski) combination. Used on trees over 30 inches in diameter.
(((D)))
(E)
Three parallel cuts with the saw, leaving a step. Same in principle as (C). Used on trees of very large diameters.
Item
 
1
Undercut depth
 
2
Undercut height
 
3
Holding wood
 
4
Backcut
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-53920 Falling and buckingBucking.
(1) The tree (and root wad if applicable) must be carefully examined to determine which way the logs (and root wad) will roll, drop, or swing when the cut is completed. No worker shall be allowed in this danger zone during cutting. The cut must be made from a position that will not expose the cutter to potential injury.
(2) Logs must be completely bucked through whenever possible. If it becomes hazardous to complete a cut, then the log must be marked and identified by a predetermined method. Rigging crews must be instructed to recognize such marks and when possible, cutters must warn the rigging crew of locations where unfinished cuts remain.
(3) Cutters must give a timely warning to all persons within range of any log that may have a tendency to roll after being cut off.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-53930 Falling and buckingDanger trees.
(1) Each danger tree must be carefully checked for signs of loose bark, broken branches and limbs, or other damage before they are fell or removed. Accessible loose bark and other damage that may create a hazard for an employee must be removed or held in place before falling or removing the tree. When a danger tree has elevated loose bark that cannot be removed, the buddy system must be used to watch for and give warning of falling bark or other hazards.
(2) Danger trees that are unsafe to cut must be blown down with explosives or fell by other safe methods.
(3) To avoid use of wedges, which might dislodge loose bark or other material, danger trees ((must)) should be fell in the direction of lean unless other means (mechanical or dynamite) are used.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-53940 Falling and buckingSpringboards and tree jacking.
(1) Springboards must be:
(a) Made of clear, straight grained sound stock;
(b) Long enough, wide enough, and strong enough; and
(c) Replaced when they will no longer safely support the expected load at the extreme end.
(2) Springboard irons must be well lipped and firmly attached with bolts or other equally strong attachment.
(3) Saw chains must be stopped while shifting springboards.
(4) Jack plates must be used with hydraulic tree jacks and the base plate must be seated on solid wood inside the bark ring as close to level as possible.
(5) When necessary, two workers must be present at the tree during hydraulic tree jacking to lend assistance.
(6) Wedges must be used as a follow-up method while using tree jacks, and continuously moved in as the tree is jacked.
(7) All hydraulic tree jacks must be equipped with a check valve and the pump must be equipped with an operable pressure gauge.
(8) Jacking a tree straight uphill is prohibited when the tree may slide back past the stump.
(9) On slopes over 50% grade, tree(s) must at least be quartered to a degree that prevents employees from being exposed to the possibility of sliding or rolling trees or logs.
(10) Trees must not be felled directly uphill when the probability of the tree sliding past the stump is likely.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-541 Tree pulling.
(1) The cutter must be responsible for determining if a tree can be safely pulled. If, for any reason, the cutter believes the tree pulling cannot be completed safely, the tree must be conventionally fell.
(2) When using a radio, positive radio communications must be maintained at all times between the tree pulling machine and cutter when tree pulling. An audible signal must be blown when the initial pull is made on the tree and the line is tightened. Hand signals, instead of radio communications and an audible signal, may be used only if the cutter is clearly visible to the tree puller operator.
(3) A choker with bell, or a line and sleeve shackle must be used as the means of attachment around the tree when tree pulling. (See also WAC 296-54-54710(4).) The bight on the line must be the minimum necessary to hold the choker or line around the tree.
(4) The tree pulling machine must be equipped with a torque converter, fluid coupler, or an equivalent device to ensure a steady even pull on the line attached around the tree.
(5) The tree pulling line must have as straight and direct path from the machine to the tree as possible. Physical obstructions that prevent a steady even pull on the tree pulling line must be removed or the line must be rerouted.
(6) ((Siwashing,)) Using a physical object such as a stump or tree in lieu of a block, in order to change tree pulling lead, is prohibited.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-543 Mechanized falling.
(1) A flagger(s) must be assigned on roads where hazardous conditions are created from falling trees. Where there is no through traffic, such as on a dead end road, warning signs or barricades may be used instead of a flagger(s).
(2) Self-propelled mobile falling equipment used for falling trees must be designed, or have auxiliary equipment installed, that will cause the tree to fall in the intended direction.
(3) Until the machine operator has acknowledged that it is safe to do so, no employee ((shall)) will approach a mechanical falling operation closer than a minimum of two tree lengths of the trees being fell.
(4) Mechanized falling must be conducted in a way that does not endanger people or equipment.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-545 Climbing equipment and passline.
(1) Standard climbing equipment must be furnished by ((the employer)) you. However, the climber may use personal equipment, if it meets the requirements of this section and is permitted by ((the employer)) you.
(a) The climber may fasten climbing rope by passing it through "D" rings fastened to the belt and around his body before tying it to itself.
(b) An extra set of climbing equipment must be kept at the ((jobsite)) job site and another person with climbing experience must be present.
(2) The climber must be equipped with a climbing equipment assembly that includes:
(a) A safety belt with double "D" rings;
(b) Steel spurs long and sharp enough to hold in any tree in which they are used; and
(c) A climbing rope (lanyard) made of ((wire-core hemp, wire or chain construction)) a high-quality steel safety chain of 3/16-inch size or larger or a wire core rope.
(3) All climbing equipment must be maintained in good condition.
(4) Defective climbing equipment must be immediately removed from service.
(5) Going up a raised portable spar or tower without suitable equipment is prohibited.
(6) Only an employee directed by the climber may work directly under a tree. The climber must give warning before intentionally dropping any objects or when objects are accidentally dropped.
(7) Running lines must not be moved while the climber is working in the tree, except such "pulls" as climber directs and are necessary for the work.
(8) One experienced person must be assigned to transmit the climber's signals to the machine operator.
(a) This signal person must not otherwise be occupied while the climber is in the tree.
(b) The machine operator must not be distracted while the climber is using the passline.
(c) The designated signal person must be positioned clear of hazards from falling, flying, or thrown objects.
(9) The climber must be an experienced logger with proper knowledge of logging methods and the safety of rigging spar and tail trees.
(10) Noisy equipment such as power saws, tractors, and shovels must not be operated near where a climber is working when such noise will interfere with the climber's signals.
(11) Climbing and passline equipment must not be used for other purposes.
(12) Lineman hooks must not be used as spurs.
(13) Tools used by the climber, except the chain saw, must be safely secured to ((climbers)) climber's belt when not in use.
(14) Using snaps on a climber's rope is prohibited unless a secondary safety device between the belt and snap is used.
(15) A climber's rope must encircle the tree before the climber leaves the ground, except when the climber is riding the passline.
(16) While the climber is working in the tree, persons must keep ((at)) a sufficient distance from the tree to be clear of falling objects.
(17) When used, passline blocks must be kept in alignment and free from fouling.
(18) Loose equipment, rigging, or material must either be removed from the tree or securely fastened.
(19) Drums used for passlines must have enough flange depth to prevent the passline from running off the drum at any time.
(20) Passlines must:
(a) Be at least 5/16-inch and not over 1/2-inch in diameter;
(b) Not be subjected to sawing on other lines or rigging, and kept clear of all moving lines and rigging;
(c) Be one continuous length and in good condition with no splices, knots, molles, or eye-to-eye splices between the ends;
(d) Long enough to provide three wraps on the drum before the climber leaves the ground.
(21) Passline chains must be:
(a) At least 5/16-inch alloy or 3/8-inch high test chain and must not contain cold shuts or wire strands;
(b) Attached to the end of the passline with a screw-pin shackle, a slip-pin shackle with a nut and molle, or a ring large enough to prevent going through the pass block; and
(c) Fitted with links or rings to prevent workers from being pulled into the passline block.
(22) Pass blocks must:
(a) Be inspected before placing in each spar and the necessary replacements or repairs made before they are hung;
(b) Have the shells bolted under the sheaves;
(c) Have the bearing pin securely locked and nuts keyed, or the block positively secures the nut and pin;
(d) Be equipped with sheaves at least six inches in diameter; and
(e) Comply with WAC 296-54-54750.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-54730 RiggingShackles.
(1) Shackles used to hang blocks, jacks, or rigging on spars, must have the pins secured with a nut and cotter key or a nut and molle.
(2) Flush pin, straight-sided shackles must be used for mainline, slackline and skyline extensions.
(3) Shackles with screw pins, knockout or slip pins may be used to anchor skylines, slackline, guyline, and/or guyline extensions.
(4) All other shackles must be screw pin type or have the pin secured with a nut and cotter key or a nut and molle, except as specified elsewhere for specific purposes.
(5) The opening between the jaws of shackles used to hang blocks, jacks, and rigging and to join or attach lines, must ((be a maximum of)) not be more than one inch greater than the size of the rope, swivel, or shackle to which it is attached.
(6) All shackles must be one size larger than the lines they connect and made of forged steel or material of equivalent strength.
For example:
1-inch Extra Improved Plow Steel (EIPS) line requires a 1 1/8-inch shackle, 1-inch swaged line require 1 1/4-inch shackle.
(7) Shackles used to join lines must be hung with the pin and "U" part of the shackle through the eyes of the lines.
 
Medium Bell
With Safety Pin
Flush Pin
Straight Side
Wide Bell-shaped Hanging Type With Safety Pin
Guyline Sleeve
With Knock-out Pin
Figure 2-2: Shackles
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-54740 RiggingStraps.
Straps must be used according to the following requirements:
(1) Straps or chokers used to hang corner or tail blocks and straps used to anchor skylines/slacklines must be the size required by Table 1: Strap/Choker Size in Inches.
Table 1: Strap/Choker Size in Inches
Running Line Size in Inches
Block or Skyline / Slackline Hung in Both Eyes
Block Hung in Single Eye
5/16
1/4
1/2
3/8
3/8
9/16
7/16
7/16
5/8
1/2
1/2
3/4
9/16
9/16
7/8
5/8
5/8
1
3/4
3/4
1 1/8
7/8
7/8
1 1/4
1
1
1 3/8
1 1/8
1
 
1 1/4
1
 
1 3/8
1
 
1 1/2
1 1/8
 
1 5/8
1 1/4
 
1 3/4
1 1/4
 
1 7/8
1 3/8
 
2
1 3/8
 
Note:
Both strap ends must be under equal tension.
(2) Straps/chokers must be equivalently sized for the line they support, e.g., extra improved plow steel (EIPS) line requires EIPS straps or equivalent strength material, and swaged lines require swaged straps or equivalent strength material.
(3) When a single choker or single part strap is used to support lift blocks, jacks and tree shoes they must be adequately sized to support the applied loads.
(((3))) (4) When a two part strap or two chokers are used to hang a block, jack, tree shoe, or rigging, both eyes or ends must be under equal tension.
(((4))) (5) Where two equal length chokers are used instead of one choker to gain extra breaking strength, they must be arranged in a swede connection.
(((5))) (6) Straps or chokers used to hang or support blocks, jacks, tree shoes, or rigging must be replaced when there is evidence of damaged or broken wires. They must:
(a) Be made of new wire rope; or
(b) Meet the pull test strength of new wire rope.
(((6))) (7) Threading wire rope straps eye through eye is prohibited.
(((7))) (8) Synthetic straps must be used as recommended by the manufacturer and only at a flat or downward angle unless wrapped one full turn around the tree support to prevent the strap from riding up on the support.
(((8))) (9) Synthetic straps must be removed from service when wear reaches the limits prescribed by the manufacturer or when deterioration is evident.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-54750 RiggingBlocks.
(1) Load-bearing blocks must:
(a) Not be used for heavier strains or lines than those for which they are constructed;
(b) Be fitted with line guards;
(c) Be designed and used to prevent fouling;
(d) Be kept in proper alignment when in use;
(e) Be equipped with bearing and yoke pins that will safely withstand the strains imposed, and are securely fastened; and
(f) Be equipped with sheaves designed for the size of the wire rope used.
EXCEPTION:
Subsections (b), and (f) do not apply to rig-up ("Tommy Moore") blocks.
(2) Blocks with cracked or excessively worn sheaves or shells must not be used.
(3) Block bearings must be kept well lubricated.
(4) All pins in blocks must be properly secured by "Molle Hogans" or keys of the largest size the pin hole will accommodate. When blocks are hung in spars, pins must be secured with a nut and cotter pin or nut and molle.
(5) Lead blocks used for yarding, swinging, loading and unloading used in wood spars ((shall)) must:
(a) Be of the type and construction designed for this purpose; and
(b) Be bolted with not less than two bolts through the shells below the sheaves in a manner that will retain the sheave and line in case of bearing pin failure (this does not apply to haulback lead blocks)((; and)).
(((c))) (6) Mainline blocks ((shall)) must have a sheave diameter of not less than twenty times the diameter of the mainline.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-54760 RiggingHanging blocks.
(1) All logging systems must use enough corner or tail blocks to distribute the stress on anchors and attachments.
(2) Blocks (other than passline or haywire) must be hung by one of the following methods:
(a) Hanging the block in both eyes or Ds of the straps (((threaded)) threading eye through eye of wire rope straps ((are)) is prohibited); ((or))
(b) If chokers are used, the ferrule must be properly seated in the socket of the bell or hook to prevent the ferrule from coming unbuttoned. The chokers must be the size required in WAC 296-54-54740(1); or
(c) If single part straps are used, the straps must be secured with a shackle and be the size required in WAC 296-54-54740(1).
(3) The yoke pin of haulback blocks ((shall)) must be inserted with the head facing the direction from which the rigging approaches.
(4) When there is danger of tail block straps slipping up or off the stump or tree, the stump or tree must be adequately notched or the line properly wrapped and secured. When the tail tree or stump is not secure, it must be tied back.
AMENDATORY SECTION (Amending WSR 06-07-142, filed 3/21/06, effective 5/1/06)
WAC 296-54-557 Wire rope.
(1) Wire rope must be of the same or better grade as originally recommended by the equipment manufacturer.
(2) Wire rope must be removed from service when any of the following conditions exist:
(a) In running ropes, six randomly distributed broken wires in one lay or three broken wires in one strand in one lay;
(b) Wear of one-third the original diameter of outside individual wires. Kinking, crushing, birdcaging, or any other damage resulting in distortion of the rope structure;
(c) Evidence of any heat damage from any cause;
(d) Reductions from nominal diameter of more than 3/64-inch for diameters to and including 3/4-inch, 1/16-inch for diameters 7/8-inch to 1-1/8-inch, inclusive, 3/32-inch for diameters 1-1/4-inches to 1-1/2-inches inclusive;
(e) In standing ropes, more than two broken wires in one lay in sections beyond end connections or more than one broken wire at an end connection; and
(f) ((In standing ropes, when twelve and one-half percent of the wires are broken within a distance of one wrap (lay); and
(g))) Corroded, damaged, or improperly applied end connections.
EXCEPTION:
Out-of-service requirements do not apply to chokers, grapple opening lines, tag lines, cat and skidder winch lines, and drop lines that are not used to move the carriage. However, an authorized, qualified person must thoroughly inspect these cables adhering to the requirements of WAC 296-54-54710 (1) and (3).
(3) Wire rope must be kept lubricated as conditions of use require.
 
Wire rope selection is an important element in cable logging.
WIRE ROPE
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-55720 Wire ropeSplicing.
(1) Marlin spikes must be used for splicing. The marlin spikes must be:
(a) Large enough for the size of the line being spliced; and
(b) Maintained in good condition((;)).
(2) Short splices, eye-to-eye splices, cat's paws, and knots are prohibited except for moving nonload-bearing lines. Knots may be used on single drum tractors, grapple pickup lines, and dropline carriage systems using slider bells if the knot is tied on the end of the dropline.
(3) Wire rope one-half inch in diameter or less must be tucked at least two times provided the rope is used only as a strawline.
(4) Eye splices in all regular lay lines and straps must be tucked at least three times.
(5) Eye splices in lang lay lines must be tucked at least four times.
(6) Splices, other than eye splices, in lang lay loading lines are prohibited.
(7) Long splices must be used to permanently join regular lay running line.
(8) The length of line strand to be unraveled to make a long splice in wire rope must be as shown in Table 2: Length of Line Strand. The full length of the splice is twice the length of the rope to be unraveled.
Table 2: Length of Line Strand
Rope Diameter
To Be Unraveled
Total Length
1/4"
8'
16'
3/8"
8'
16'
1/2"
10'
20'
5/8"
13'
26'
3/4"
15'
30'
7/8"
18'
36'
1"
20'
40'
1-1/8"
23'
46'
1-1/4"
25'
50'
1-3/8"
28'
56'
1-1/2"
30'
60'
1-5/8"
33'
66'
1-3/4"
35'
70'
1-7/8"
38'
76'
2"
40'
80'
Note:
Unraveling 40 lays of cable on each side will give the required length of splice regardless of the diameter.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-55730 Wire ropeAttaching end fastenings.
(1) The manufacturer's recommendations must be followed when attaching sockets and other end fastenings.
(2) Using cable clips or clamps for joining lines is prohibited, except to transfer slack lines from one place to another.
(3) When U-bolt cable clips are used to form eyes, Table 3: U-bolt Cable Clips to Form Eyes must be used to determine the number and spacing of clips.
Table 3: U-bolt Cable Clips to Form Eyes
Improved Plow Steel Diameter of Rope
Number of Clips Forged
Required Other
Material
Minimum Space
Between Clips
3/8 to 5/8 inch
3
4
-3/4 inch
3/4 inch
4
5
4-1/2 inch
7/8 inch
4
5
5-1/4 inch
1 inch
5
6
6 inches
1-1/8 inch
6
6
6-3/4 inch
1-1/4 inch
6
7
7-1/2 inch
1-3/8 inch
7
7
8-1/4 inch
1-1/2 inch
7
8
9 inches
(4) When U-bolt cable clips are used:
(a) For eye splices, the U-bolt wire rope clip must be attached so that the U section is in contact with the dead or short end of the rope (see Figure 3: Eyes Formed with U-bolt Cable Clips);
(b) U-bolt cable clips must be spaced at least six rope diameters apart to obtain the maximum holding power. Nuts must be tightened evenly and tightened again after application of the first sustained load. After the rope has been used and is under tension, the clips must be tightened again to take up any looseness caused by the tension reducing the rope diameter;
(c) With high strength wire rope, one more U-bolt cable clip must be added for each grade above improved plow steel; and
(d) Eyes formed with U-bolt cable clips are prohibited with running lines or straps.
(5) Wedge-type quick ferrules, such as "quick nub" must not be used as end fittings for guylines and skylines.
APPLICATION OF WIRE ROPE
U-BOLT CLIPS
Crosby Type
 
1. CORRECT METHOD—U-Bolts of clips on short end
of rope. (No distortion on live end of rope)
 
2. WRONG METHOD—U-Bolts on live end of rope.
(This will cause mashed spots on the live end of rope)
 
3. WRONG METHOD—Staggered clips; two correct
and one wrong. (This will cause a mashed spot in
live end of rope due to wrong position of center clip)
4. After rope is in service, and is under tension,
tighten clips to take up decrease in rope diameter.
Figure 3: Eyes Formed with U-bolt Cable Clips
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-561 Guylines.
(1) Guylines must be used with any logging equipment when required by the equipment manufacturer.
(2) At least the minimum number and angle of guylines recommended by the equipment manufacturer must be used.
(3) Unless otherwise specified by the equipment manufacturer, guylines must be of the following sizes:
(a) In highlead logging, the head spar guylines must be equal in breaking strength to the mainline.
(b) In skyline logging, if the skyline is one and three-eighths inch or greater, the head spar guylines must be at least one and three-eighths inch. If the skyline is less than one and three-eighths inch, the head spar guylines must be equal in breaking strength to the skyline.
(c) On all other cable logging machines, the guylines must have a breaking strength at least equal to the mainline/skyline, whichever is largest.
(d) Tail/lift and intermediate support trees must be adequately guyed to withstand any stress to which the tree may be subjected.
(4) When guylines are required for spars they must be positioned according to Table 4: Guyline Positioning, or according to the manufacturer's specifications.
Table 4: Guyline Positioning
Number of Guys on Spar
Number of Guys Sharing Load
Positioning
Figure Number
1
1
4 - 1 Guyline Case
2
2
5 - 2 Guyline Case
3
3*
6 - 3 Guyline Case
 
2
7 - 3 Guyline Case (2)
4
2
8 - 4 Guyline Case
5
2
9 - 5 Guyline Case
 
3
10 - 5 Guyline Case (2)
6
2
11 - 6 Guyline Case
 
3
12 - 6 Guyline Case (2)
7
3
13 - 7 Guyline Case
8
2
14 - 8 Guyline Case
 
4
15 - 8 Guyline Case (2)
*
For metal spars designed to operate without snap guy
(5)(((a))) Guylines supporting metal spars must be made of plow steel or better material and must be maintained in good condition.
(((b))) Guylines for tail/lift and intermediate support trees may be made of synthetic material and must be used according to the manufacturer's recommendations.
(6) Load bearing guyline angles must be no greater than fifty degrees measured horizontally (See Figure 18: Maximum Angle for Load Bearing Guylines and Skyline). If suitable anchors are unavailable or the terrain is so steep that the guyline angle exceeds fifty degrees, an additional guyline must be rigged to oppose the load.
(7) Guylines must be kept securely tightened while the spar, tree, equipment or rigging they support is in use.
(8) Power driven devices must be securely anchored when used to tighten guylines. Holding such devices is prohibited.
(9) All trees that interfere with proper alignment, placement, or tightening of guylines must be fell.
EXCEPTION:
It is acceptable to use the base of a tree/stump or ground conditions to change the lead of a guyline for the purpose of keeping the guyline properly positioned.
(10) Guylines must be hung in a manner to prevent a excessive bight or fouling when they are tightened.
(11) The use of loops or molles for attaching guylines is prohibited.
(12) The U part of shackles or sleeves must be around the guyline and the pin passed through the eye of the guyline.
(13) Splicing of guylines is prohibited except to make an eye splice.
(14) All spliced guyline eyes must be tucked at least three times.
(15) Extensions to guylines must be:
(a) Equal in breaking strength to the guyline to which they are attached; and
(b) Connected only by a shackle connecting two spliced eyes, pressed eyes or by double-end hooks. Connections must have at least one and one-half times the strength of the guyline.
(16) When hanging a block or jack on a guyline, only sleeve-type safety pin shackles must be used. The shackle sleeve ((shall)) will have not less than two and one-half times the line diameter bearing on the guyline.
 
Figure 4: 1 Guyline Case
 
Figure 5: 2 Guyline Case
 
Figure 6: 3 Guyline Case
 
Figure 7: 3 Guyline Case (2)
 
Figure 8: 4 Guyline Case
 
Figure 9: 5 Guyline Case
 
Figure 10: 5 Guyline Case (2)
 
Figure 11: 6 Guyline Case
 
Figure 12: 6 Guyline Case (2)
 
Figure 13: 7 Guyline Case
 
Figure 14: 8 Guyline Case
 
Figure 15: 8 Guyline Case (2)
 
Figure 16: Positioning Guylines in Back of Tree
 
Figure 17: Positioning Guylines in Front of Tree
 
Figure 18: Maximum Angle for Load Bearing Guylines and Skyline
 
Figure 19: 4 Guyline Case - Tail/Lift Tree Guying
 
Figure 20: 2 Guyline Case - Tail/Lift Tree Guying
(gravity outhaul, nonslackpulling carriage)
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-563 Guying tail/lift trees.
(1) Whenever a tail/lift tree is within reach of the work area and the rigging is placed on the tail/lift tree at a height greater than five times the tree diameter (dbh), at least two guylines must be used unless tree size and strength and rigging position eliminate the need for guylines or employees must be in the clear before the go-ahead signal is given.
(2) Guylines on tail/lift trees must not be anchored to standing trees unless:
(a) There is no danger that the guyline anchor tree will enter the work area;
(b) The guyline anchor tree is properly tied back; or
(c) Employees are in the clear of the guyline anchor tree(s) before the go-ahead signal is given.
(3) When guylines are required, they must be positioned according to Figure 16: Positioning Guylines in Back of Tree and Figure 19: 4 Guyline Case - Tail/Lift Tree Guying as follows:
(a) When the angle between the horizontal and skyline coming into the tree (angle A in Figure 16) is less than the angle between the horizontal and the skyline leaving the tree towards the anchor point (angle B in Figure 16), the guylines must be in back of the tail/lift tree as specified in Figure 19.
(b) If angle A is greater than angle B, then the guys must be placed in front of the tail/lift tree. This situation usually occurs when a tail/lift tree is used during downhill yarding as shown ((below)) above. Placing the guys on the uphill side only helps to pull the tail/lift tree over uphill.
(c) If a suitable anchor is not available within a specified shaded zone, two guylines may be used instead of one guyline, provided a guyline is placed on either side of and as near as possible to the affected shaded zone.
(4) Tail/lift trees must be supported by additional guylines if necessary, to ensure the stability of the tree.
(5) Guylines for tail/lift trees may be made of synthetic material and must be used according to the manufacturer's recommendation.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-567 Rigging skylines.
(1) A skyline must not make an angle greater than fifty degrees measured from the horizontal as it leaves the tail/lift tree. (See Figure 18: Maximum Angle for Load Bearing Guylines and Skyline.)
(2) When rigged in a tail/lift tree, the skyline must be anchored no more than eight degrees offline from the rearward projection of the skyline. If a suitable anchor is not available within the specified zone and the tail/lift tree is stable, a more suitable anchor outside the zone may be used. (See Figure 23: Skyline Positioning Limits Tail/Lift Tree.)
(3) A skyline must not be considered a guyline.
(4) Extensions to skylines must be equal in breaking strength to the skyline to which they are attached and must not alter the safe capacity of the tower. In addition, the extension must be attached only by a regular long splice or by a flush pin straight side shackle connecting the two eyes.
Note:
See exception in WAC 296-54-553 (4)(e).
(5) Live, running or standing skylines must be anchored by one of the following methods:
(a) Directly to a stump or suitable manufactured anchor;
(b) Directly to the base of a standing tree provided the point of attachment is no more than three feet above the ground and no part of the tree will enter the work area if pulled over;
(i) If the tree will enter a work area, it must be properly tied back; or
(ii) Employee(s) must be in the clear before the go-ahead signal is given.
(c) By passing the skyline though a jack or block hung on a tail/lift tree before being anchored.
(6) Skylines or mainlines must be secured by one of the following methods:
(a) With at least two and one-half wraps, well spiked, or properly clamped (see WAC 296-54-569 (5)(b)); or
(b) Choked by using an approved shackle over the skyline or mainline with the pin through the eye and hung in a manner to prevent excessive bight or fouling when tightened; or
(c) With an approved strap having both eyes hung in a shackle and the knockout pin or safety pin through the eye of the skyline or mainline.
(7) Attaching the end of the skyline or slackline to the base of the rigged tail/lift tree is prohibited.
SKYLINE POSITIONING LIMITS TAIL/LIFT TREE
 
Figure 23: Skyline Positioning Limits Tail/Lift Tree
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-569 Anchoring.
(1) Stumps used to anchor guylines and skylines must be carefully chosen for position, height, and strength. When necessary, stump anchors must be tied back to distribute the load.
(2) Stump anchors, when spiked, must be barked where attachments are to be made.
(3) Stump anchors must be adequately notched to keep the line in place and not adversely affect the stump strength.
(4) Employees must not stand close to the stump or tree or in the bight of lines as the guyline or wraps are being tightened.
(5) When spikes or cable clamps are used, guylines or skylines must be anchored with at least two and one-half wraps around the stumps. Wraps must:
(a) Be well secured with at least eight spikes or six staples in sound wood on the first and last wrap; or
(b) Have the end of the line secured with two wire rope clips on lines up to one inch diameter and three wire rope clips on lines one inch diameter and over.
(6) Properly installed deadman anchors are permitted. Guylines must not be directly attached to deadman anchors. Suitable straps or equally effective means must be used.
(7) ((Guylines of portable spars, wood spars or towers must not be anchored to standing trees if the unit is used as a head tree, except as specified in subsection (8) of this section.
(8) In special cases such as hanging on foreign ownership or in cable thinning operation where frequent moves make the retrieval of fell guyline trees difficult, the following will apply:
(a) Standing trees within reach of a work area or haul road may be used provided:
(i) They are solid;
(ii) Have a sound undisturbed root system;
(iii) If fell, would be suitable for a guyline stump or tailhold as required in subsection (1) of this section; and
(iv) Are properly tied back to distribute the load; or
(b) Guyline and/or tailhold anchor trees, when located so they will not fall into the work area or haul road, need not be tied back if stable.
Note:
Under no circumstances must an employer accept a requirement, or be required to use standing trees to anchor guylines.
(9))) When a standing tree is used as an anchor for guylines of portable spars, wood spars or towers:
(a) The tree must be properly tied back if it is within reach of a work area, landing area or haul road;
(b) The tree must be carefully chosen for strength;
(c) The line or strap must be attached to the base of the tree; and
(d) The tree must be adequately notched.
Note:
The depth of the notch should not be any deeper than what is necessary to keep the line/strap from sliding up the tree.
(8) Rock bolt anchors must be grouted, installed, tested, and maintained according to the rock bolt manufacturer's recommendations.
(((10))) (9) Anchors must be regularly inspected while the logging operation is in progress. Insecure or hazardous anchors must be corrected immediately.
(((11))) (10) Artificial earth anchors must be installed and used according to their design specifications and manufacturer's recommendations.
(((12))) (11) Mobile equipment may be used to anchor skylines, running lines and guylines, provided the weight of the machine or other methods are used to ensure machine stability for all applied loads.
 
Figure 24: Rigging Illustrations
AMENDATORY SECTION (Amending WSR 06-07-142, filed 3/21/06, effective 5/1/06)
WAC 296-54-573 Logging machinesGeneral.
(1) All logging machinery must have speed limiting devices, safety stops, or emergency shut down devices or shut off valves, with the controls located so that in the event of an emergency, the prime mover may be shut down from a safe place.
(2) The floor and lower portion of cabs must be completely enclosed with solid material, except at entrances, to prevent the operator from being injured by obstacles which otherwise could enter the cab compartment.
(3) Machine operators must be experienced in operating the equipment they use.
EXCEPTION:
Inexperienced employees may operate equipment to gain experience while in training but may do so only while working under the immediate supervision of an experienced authorized person.
(4) All machine controls must be marked as to their purpose in the operation of the machine.
(5) The rated capacity of any vehicle transporting a machine must not be exceeded.
(6) Machines must be loaded, secured, and unloaded in a manner that will not create a hazard for any employee.
Note:
This requirement includes the loading, securing and unloading of a machine on and off a transport vehicle.
(7) ((The employer)) You must not make any modifications or additions that affect the capacity or safe operation of the equipment without written approval of the manufacturer or a qualified engineer. If modifications or changes are made, the capacity, operation and maintenance instruction plates, tags, or decals, must be changed accordingly. The original safety factor of the equipment must never be reduced.
(8) Equipment must be classed and used according to the manufacturer's rating. Where low gear ratios or other devices are installed to increase the line pull in accordance with subsection (7) of this section, the size of the rigging must be increased accordingly so that it will safely withstand the increased strains.
(9) Each machine, including any machine provided by an employee, must be maintained in serviceable condition and the following:
(a) Each machine must be inspected before initial use during each workshift. Defects or damage must be repaired or the unserviceable machine is replaced before beginning work.
(b) Operating and maintenance instructions must be available on the machine or in the area where the machine is being operated. Each machine operator and maintenance employee must comply with the operating and maintenance instructions.
(c) Each machine must be operated only from the operator's station or as otherwise recommended by the manufacturer.
(d) Employees must not be allowed to ride on any load.
(10) Horns and travel alarms, which are part of the machine's original equipment, must be maintained in serviceable condition.
(11) The yarding machine or vehicle, including its load, must be operated with safe clearance from all obstructions.
(((11))) (12) While manual/mechanized falling is in progress, all logging machines must be operated at least two tree lengths away from trees being fell.
EXCEPTION:
This provision does not apply to logging machines performing tree pulling operations or logging machines called upon by the cutter to ground hazard trees. All cutters must be notified of the logging machine entrance into the area and all falling within two tree lengths of the logging machine must stop.
(((12))) (13) If a hydraulic or pneumatic storage device can move the moving elements such as, but not limited to, blades, buckets, saws and shears, after the machine is shut down, the pressure or stored energy from the element must be discharged as specified by the manufacturer.
(((13))) (14) Loads must not exceed the rated capacity of the pallet, trailer, or other carrier.
(((14))) (15) Boom-type logging machines must have a boom stop to prevent over-topping of the boom.
(((15))) (16) Boom points of timber booms must be equipped with metal straps, plates, or other devices as needed to properly secure eyebolts and fittings used to support lines, blocks, or other rigging.
(((16))) (17) Logging machine sleds or bases must be strong enough to withstand any stresses imposed upon them.
(((17))) (18) Stationary logging machines must be securely anchored or otherwise stabilized to prevent unintended movement while yarding or skidding.
(((18))) (19) Logging machines and their components must be securely anchored to their bases.
(((19))) (20) Logging machines must be kept free of flammable waste materials and any materials that might contribute to slipping, tripping or falling.
(((20))) (21) A safe and adequate means of access and egress to all parts of logging machinery where persons must go must be provided and maintained in a safe and uncluttered condition. Machine access systems, meeting the specifications of the Society of Automotive Engineers, SAE J185, June 1988, "Recommended Practice for Access Systems for Off-Road Machines," must be provided for each machine where the operator or any other employee must climb onto the machine to enter the cab or to perform maintenance. Walking and working surfaces of each machine and machine work station must have a slip-resistant surface to assure safe footing.
(((21))) (22) Enclosed-type cabs installed on mobile logging machines must have two means of exit. One may be an emergency exit and be available for use at all times regardless of the position of the side arms or other movable parts of the machine. An easily removable window is acceptable as the emergency exit if it is large enough for an employee to readily exit.
EXCEPTION:
Cable yarders manufactured before July 1, 1980 are not required to have two means of exit.
(((22))) (23) Before leaving the operator's station of a machine, the operator must ensure the machine is secured as follows:
(a) The parking brake or brake locks must be applied;
(b) The transmission must be placed in the manufacturer's specified park position; and
(c) Each moving element such as, but not limited to, blades, buckets, saws and shears, must be lowered to the ground or otherwise secured.
(((23))) (24) Storing employee property, tools, or other miscellaneous materials on or within three feet of any logging machine is prohibited if retrieving the items would expose an employee to the hazardous pinch point area between the rotating superstructure and the nonrotating undercarriage.
(((24))) (25) Employees must approach the hazardous pinch point area only after informing the operator of that intent and receiving acknowledgment from the operator that the operator understands the employee's intention. All logging machines must be stopped while any employee is in the hazardous pinch point area.
(((25))) (26) After adjustments or repairs are made, logging machines must not be operated until all guards are reinstalled, safety devices reactivated, and maintenance equipment removed.
(((26))) (27) Fairleads must be properly aligned at all times and designed to prevent line damage.
(((27))) (28) Employee(s) must not ride on any mobile logging machine unless provided with seating, seat belts, and other protection equivalent to that provided for the operator.
EXEMPTION:
Mechanics in the course of their job and trainees, operating under circumstances that minimize their exposure to dangerous situations, are exempt from this requirement.
(((28))) (29) Riding on arches, reaches or turn of logs is prohibited.
(((29))) (30) Tractors, skidders, arches, or logs being yarded by them must not run over or rub against anchored lines, tailhold stumps, or other rigging.
(((30))) (31) Ends of lines attached to drums on logging machines must be secured by end attachments that develop the ultimate strength of the line unless three wraps of line are maintained on the drum at all times.
EXCEPTION:
This does not apply to tractors or skidders.
(((31))) (32) Wire rope must be wound on drum spools in a manner to prevent excessive wear, kinking, chafing or fouling.
(((32))) (33) Guylines required in rigging spars or towers must be evenly spooled to prevent fouling.
(((33))) (34) A guide pulley, tool, stick, iron bar or other mechanical or manual means must be used when guiding lines onto drums. Guiding lines onto drums with any part of the body in direct contact with the line is prohibited.
(((34))) (35) A limit switch must be installed on electric-powered log loaders to prevent the lift arms from traveling too far in the event the control switch is not released in time.
(((35))) (36) All forklift type log handling machines must be equipped with a grapple system and the arms must be closed whenever logs are being carried.
(((36))) (37) When forklift machines are used to load, unload, or handle trailers, a positive means of holding the lifting attachment on the fork must be installed and used.
(((37))) (38) Loads on forklift type log handling machines must be transported as low as safely operable without obstructing visibility.
(((38))) (39) Guyline drum controls and outrigger controls must be separated and clearly identified in a manner that will prevent the engaging of the wrong control.
(((39))) (40) Each machine must be equipped with guarding to protect employees from exposed moving elements, such as, but not limited to, shafts, belts, pulleys on chains, sprockets and gears in accordance with the requirements of this standard and chapter 296-806 WAC, Machine safety. Guards must be in place at all times when machines are in use.
Note:
This does not apply to lifting or yarding components such as, but not limited to, cable nip points, sheaves and blocks.
(((40))) (41) Each machine used for debarking, limbing, and chipping must be guarded to protect employees from flying wood chunks, logs, chips, bark, limbs, and other material in accordance with the requirements of this standard and chapter 296-806 WAC, Machine safety.
(((41))) (42) Grab rails must be provided and maintained in good repair on all walkways of stationary units elevated more than four feet.
(((42))) (43) Towed equipment such as, but not limited to, skid pans, pallets, arches, and trailers, must be attached to each machine or vehicle to allow a full ninety degree turn; to prevent overrunning of the towing machine or vehicles; and to ensure that the operator is always in control of the towed equipment.
(((43))) (44) Timbers used for masts or booms ((shall)) must be straight-grained, solid, and capable of withstanding the working load.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-57350 Logging machinesTractors and skidders.
(1) Operators must operate and control their machines in a safe manner and avoid operations in areas where machine stability may not be maintained.
(2) Winch lines on logging tractors or skidders must be attached to the drums with a breakaway device.
(3) Arches must be equipped with line guards.
(4) A turnaround, if needed for skidders, must be provided on all skidding roads every 500 feet.
(5) The following safe work procedures must be followed:
(a) Lines must not be allowed to trail behind the tractor or skidder where it may hang up and snap forward.
(b) Each machine must be positioned during winching so the machine and winch are operated within their design limits.
(c) Logs/trees must be ((chocked)) choked near the ends of the logs/trees whenever possible and safely positioned before traveling.
(d) Before climbing or descending grades, the proper gear must be selected to allow the engine to govern the tractor speed.
(e) On side hills, abrupt turns uphill must be avoided. The tractor or skidder must be backed downhill first then turned uphill. The turn may be slacked off as necessary to permit this maneuver.
(f) Tractor or skidder speed must be adjusted to the circumstances prevailing. Excessive or uncontrolled speed must be avoided.
(6) Where tractor and skidder operators or helpers, because of the nature of their work duties, are required to wear calk soled footwear, the decks and operating foot controls must be covered with a suitable nonslip material.
AMENDATORY SECTION (Amending WSR 06-07-142, filed 3/21/06, effective 5/1/06)
WAC 296-54-57355 Logging machinesProtective structures for operators.
(1) Each tractor, skidder, log stacker and mechanical felling device, such as tree shears or feller-buncher, placed into initial service after February 9, 1995, must be equipped with falling object protective structure (FOPS) and/or rollover protective structure (ROPS). The employer must replace FOPS or ROPS which have been removed from any machine.
EXCEPTION:
This requirement does not apply to machines which are capable of 360 degree rotation.
(2) ROPS must be installed, tested, and maintained in accordance with the Society of Automotive Engineers SAE J1040, April 1988, "Performance Criteria for Rollover Protective Structures (ROPS) for Construction, Earthmoving, Forestry, and Mining Machines."
(3) The ROPS must be high enough and wide enough so that it will not impair the movements of the operator or prevent his immediate escape from the vehicle in emergencies and must allow as much visibility as possible. Clearance above the deck and the ROPS of the vehicle at exits must be at least fifty-two inches (1.3 meters).
(4) Certified roll-over protective systems must be identified by a metal tag permanently attached to the ROPS in a position where it may be easily read from the ground. The tag must be permanently and clearly stamped, etched or embossed indicating the name and address of the certifying manufacturer or registered professional engineer, the ROPS model number (if any) and the vehicle make, model or serial number the ROPS is designed to fit.
(5) Roll-over protective structure systems must be maintained in a manner that will preserve their original strength. Welding must be performed by qualified welders only. (A qualified welder is defined under "welder qualification" in American Welding Society A.W.S. A3.0-69.)
(6) FOPS structures must be installed, tested and maintained according to:
(a) The society of automotive engineers SAE J231-1971, "minimum performance criteria for falling object protective structures (FOPS) prior to February 9, 1995."
(b) Society of automotive engineers SAE J231, January 1981, "minimum performance criteria for falling object protective structures (FOPS) for each tractor, skidder, log stacker, log loader and mechanical falling device, such as tree shears or faller-buncher, placed into initial service after February 9, 1995."
(7) ((The employer)) You must replace FOPS that have been removed from any machine.
(8) Vehicles with ROPS or FOPS as required in subsection (1) of this section, must comply with the society of automotive engineers SAE J397a-1972, "deflection limiting volume for laboratory evaluation of roll-over protective structures (ROPS) and falling object protective structures (FOPS) of construction and industrial vehicles." Vehicles placed into initial service after February 9, 1995, must meet the requirements of SAE J397-1988.
(9) The opening in the rear of the ROPS on the crawler or rubber-tired tractors (skidders) must be covered with 1/4-inch diameter woven wire having not less than 1-1/2 inches or more than 2-inch mesh, or material which will afford equivalent protection for the operator.
(a) The covering must be attached to the structural members so that enough clearance is provided between the screen and the back of the operator.
(b) Structural members must be free from projections that would tend to puncture or tear flesh or clothing.
(c) Suitable safeguards or barricades must be installed, in addition to the screen, to protect the operator when there is a possibility of being struck by any material that could enter from the rear.
(10) Crawler and rubber-tired tractors (skidders) working in areas where limbs or brush may endanger the operator must be guarded.
(a) Shear or deflector guards must be installed on each side of the vehicle at an angle leading forward and down from the top front edge of the canopy of the vehicle, which will tend to slide the brush or limbs up and over the top of the canopy.
(b) Open mesh material with openings of a size that will reject the entrance of an object larger than 1-3/4 inches in diameter, must be extended forward as far as possible from the rear corners of the cab sides to give the maximum protection against obstacles, branches, etc., entering the cab area.
(c) Deflectors must also be installed ahead of the operator to deflect whipping saplings and branches.
(d) Deflectors must be located so as not to impede entrance to or exit from the compartment area.
(e) The floor and lower portion of the cab must be completely enclosed with solid material, except at entrances, to prevent the operator from being injured by obstacles which otherwise could enter the cab compartment.
(11) Each machine manufactured after August 1, 1996, must have a cab that is fully enclosed with mesh material with openings no greater than 2 inches (5.08 cm) at its lease dimension. The cab may be enclosed with other material(s) where the employer demonstrates such material(s) provides equivalent protection and visibility.
EXCEPTION:
Equivalent visibility is not required for the lower portion of the cab where there are control panels or similar obstructions in the cab, or where visibility is not necessary for safe operation of the machine.
Enclosures for agricultural and industrial tractors manufactured after September 1, 1972, must be constructed, designed and installed as detailed in the society of automotive engineers technical report J168.
(12) Overhead protection and other barriers must be installed to protect the operator from lines, limbs, and other moving materials on or over all loading or skidding machines and on all yarding machines where the operator's station is mounted on board. The overhead covering of each cab must be of solid material and extend over the entire canopy. A skylight in a logging machine must be made of safety glass or provide equivalent protection.
Note:
This does not apply to self-loaders.
Reference:
For requirements relating to overhead protection on forklifts, see chapter 296-863 WAC, Forklifts and other powered industrial trucks.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-575 Landing area.
(1) Unless otherwise specified, landing areas must:
(a) Be large enough that if logs are to be heeled and swung, they will not strike standing timber, rigging, or other equipment or objects;
(b) Be large and level enough to land and deck the logs in the turns so that they will not slide or roll in the direction of employees or equipment. This is not intended to restrict the yarding and/or loading of logs for pole piling or an infrequent long break or tree length, provided the log is secured before unhooking the choker;
(c) Be large enough for safe movement of all logs and machinery;
(d) ((Landings must)) Be free of root wads, limbs, tops, etc., that constitute a safety hazard; and
(e) Not have materials pushed, thrown, or dumped over the edge in a manner or at a time that will endanger employees.
(2) ((When)) During roadside thinning, logs stacked on the roadside without a landing must be placed in a stable condition.
(3) During uphill yarding, the landing chute must be cleared of logs before the next turn of logs is landed unless:
(a) The logs are fully contained in the landing chute; or
(b) There is no possibility that employees working below the landing may be struck by rolling objects coming off the landing.
(4) Roadside or continuous landings must be large and wide enough to safely operate and maintain the yarding or loading equipment. Outrigger pads, tracks or wheels must be on firm, stable ground.
(5) In logging operations where the yarder is set up in the haul road and logs are landed on the slope below the road, the following must apply:
(a) If the landing chute slope is twenty percent or less, logs may be landed and decked in the chute provided the logs can be left in a stable position;
(b) If the landing chute slope exceeds twenty percent, decking is not permitted in the chute if a chaser is required to unhook the rigging from the logs or if employees are working below the landing chute and are exposed to rolling or sliding logs;
(c) If logs are to be decked below the road, the logs must be effectively secured from rolling or sliding down the hill; or
(d) If the landing process or weather conditions (rain, snow, ice, mud) prevent the required log stability and exposes employees to the hazard of rolling or sliding logs, the logs must be decked at a different location.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-577 Yarding, skidding, landing.
(1) Running lines must be arranged so that employees are not required to work in the bight of the line. When employees must work in the bight, employees must move out of the bight of the lines before the signal to move the turn is given, or be in a position where they are protected by standing timber, terrain, or other objects large enough to ensure their safety.
(2) Choker holes must be dug from the uphill side of the log when there is danger of the log rolling or moving.
(3) Chokers must be placed near the end of the log/tree whenever possible.
EXCEPTION:
When long logs or tree-length logs are being yarded and a long end is necessary to safely land the logs/trees on the available landing space.
(4) Employees must be in the clear of logs, root wads, chunks, hazardous trees, rolling material and rigging before the go-ahead signal is given and must stay in the clear until all rigging movement has stopped.
(5) Employees must move away from the turn so as to be above or behind the turn and in the clear. They must remain on their feet and face the turn before the go-ahead signal is given.
(6) All employees must remain away from rigging that is stopped at a hangup, until the rigging has been slacked to reduce the hazard.
(7) Chokers must not be hooked or unhooked until all rigging is stopped completely.
(8) Logs must not be landed until all employees, trucks or equipment are in the clear.
(9) Logs must not accumulate in the landing chute to the point where they become a hazard to the landing personnel.
(10) Logs must be stable and secure before being approached by employees and before chokers are unhooked.
(11) An employee must not buck, limb or trim logs from a position that will expose the employee to contact with moving lines.
(12) Logs must not be placed in, moved about, or removed from the bucking area of the landing unless all employees are in the clear.
(13) An unimpaired horizontal clearance of at least three feet must be maintained between the rotating superstructure of any logging machine working on a landing and any adjacent object or surface. If this clearance cannot be maintained, a safety zone barrier must be used to isolate the hazardous area. The safety zone barrier may be a warning line constructed of rope or ribbon, supported on stanchions.
(14) (("DANGER 36-INCH CLEARANCE" must be marked near the rear of the machine.
(15))) Employees must not approach a machine's working circle until the operator has acknowledged that it is safe to do so.
(((16))) (15) Whenever possible, chokers must be set from the uphill side of a log. Persons must not be on the lower side of a log which appears to be unstable or likely to roll.
(((17))) (16) When yarding during the hours of darkness, the area must be lighted enough to allow employees to safely perform their duties. The source of light must be located and directed to create minimum shadows and glare. If using a portable tailhold, lights must be directed on equipment to allow the person to visually determine that the tailhold equipment remains stabilized.
(((18))) (17) Each yarded tree/log must be placed in a location that does not create a hazard for an employee and in an orderly manner so that the trees/logs are stable before bucking or limbing is commenced.
(((19))) (18) When using a yarder, loader or skidding machine, the location of the machine or position of the yarder must be such that the operator will not be endangered by incoming logs or debris.
(((20))) (19) Employee(s) must be assigned to flag on roads or provide other equivalent protection where hazardous conditions are created from logging such as, but not limited to:
(a) Running wire rope lines or rigging across road grades, excluding guylines and standing skylines if lines remain a safe distance above the road to allow a vehicle to pass under; or
(b) The movement of logs, chunks, or debris across or suspended over road grades.
EXCEPTION:
Where there is no through traffic, such as on a dead end road or where the property owner's permission or proper authority is granted to close a section of road, warning signs and barricades may be used instead of flagger(s).
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-58130 Helicopter loggingFueling area.
(1) Separate areas must be designated for landing logs and for fueling helicopter(s).
(2) Refueling any helicopter with either aviation gasoline or Jet B (turbine) type fuel while the engine is running is prohibited.
(3) Helicopters using Jet A (turbine-kerosene) type fuel may be refueled with engines running provided the following criteria are met:
(a) Unauthorized employees must not be allowed within fifty feet of the refueling operation or fueling equipment; and
(b) Fire extinguishers must be strategically located in the fueling area and must have a combined rating of at least 20A:120BC.
(4) All fueling employees must be thoroughly trained in the refueling operation and in the use of the available fire extinguishing equipment they may be expected to use.
(5) The following are prohibited within fifty feet of the fueling area or fueling equipment:
(()) (a) Smoking;
(()) (b) Open flames;
(()) (c) Exposed flame heaters;
(()) (d) Flare pots; and
(()) (e) Open flame lights.
EXCEPTION:
Aircraft preheaters are not prohibited. However, no fueling may be performed while the heaters are in operation.
(6) The fueling area must be posted with "no smoking" signs.
(7) Because there are many causes of static electricity, fueling employees must assume that it is present at all times. Before starting refueling operations, the fueling equipment and the helicopter must be bonded and the fueling nozzle must be electrically bonded to the helicopter. Using conductive hose is not an acceptable method of bonding. All grounding and bonding connections must be electrically and mechanically firm to clean unpainted metal parts.
(8) To control spills, fuel must be pumped either by hand or power; pouring or gravity flow is prohibited. Self-closing nozzles or deadman controls must be used and must not be blocked open. Nozzles must not be dragged along the ground.
(9) In case of a spill, the fueling operation must be immediately stopped until the person in charge determines that it is safe to resume.
(10) Helicopters with their engines stopped while being refueled with aviation gasoline or Jet B (turbine) type fuel, must comply with subsection (4) through (9) of this section.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-583 Loading logs.
(1) A positive means of communication must be established and used between the truck driver and the employee loading logs to control the movement of the log truck being loaded.
(2) ((Employees must not be)) No one is permitted alongside or underneath trucks being loaded or on the load until communication has been established with the loading machine operator and the truck driver, and the employee is assured that it is safe to be there.
(3) Logs being moved or loaded must not pass over any employee or an occupied vehicle, equipment or truck cab.
(4) Standing between a truck cab and a log being loaded or unloaded is prohibited.
(5) Logs must not be lowered to the bunk while bunk or block adjustments are being made or until the employee making these adjustments is in the clear.
(6) Standing underneath a suspended trailer or its reach is prohibited.
(7) Loads must be built up or loaded in a manner to be stable without the use of wrappers. Wrappers are considered only as precautionary measures to ensure stability of the load.
(8) Where there is a danger of the grapple slipping off of logs, straps must be used in loading logs that are too large for the grapple or tongs and must be hung in both eyes.
(9) Logs must be loaded in a manner to prevent excessive strain on wrappers, binders, bunk stakes, bunk chains or straps.
(10) Logs in any tier or layer unsecured by stakes or cheese blocks must be well saddled and have their diameter centers inside the diameter centers of the outer logs of the next lower tier or layer.
(11) Bunk and wing logs must extend at least twelve inches beyond the front and rear bunks or stakes. When fixed bunks are used, logs must extend at least six inches beyond the front and rear bunk or stake.
(12) Double-ended logs above the stakes must not be loaded on the side of the load from which the binders or wrappers are intended to be released.
(13) Logs must be loaded so that no more than one-third of the weight of any log extends beyond the end of the logs or bunk supporting it.
(14) Logs must be loaded in a manner that will not impair full and free movement of the truck.
(15) Each log not contained within the stakes must be secured with at least two wrappers before the truck leaves the vicinity of the landing/loading area.
(16) All of the required wrappers must be placed on the load within sight of the landing/loading area so immediate emergency assistance can be given if necessary.
(17) Loads or logs must not be moved or shifted while binders are being applied or adjusted.
(18) The transport vehicle must be positioned to provide working clearance between the vehicle and the deck.
(19) All limbs or knots that would project beyond the stakes or legal height must be removed before the log is loaded on the car or truck.
Note:
This does not apply to incidental limbs/knots placed on loads during the normal loading process.
(20) Power saws must not be operated on top of loaded logging trucks.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-589 Log trucksGeneral.
(1) Prior to use, the operator must make a complete daily inspection of the truck and trailer with particular attention to:
(()) (a) Steering apparatus;
(()) (b) Lights and reflectors;
(()) (c) Brake boosters;
(()) (d) Brake hoses and connections;
(()) (e) Reaches;
(()) (f) Hitches (couplings);
(()) (g) Bunks;
(()) (h) Stakes;
(()) (i) Bunk blocks.
The brakes must be tested before and after movement of the vehicle. The operator must submit a written list of necessary repairs to a person designated by the employer.
(2) Any defective parts that would make the vehicle unsafe to operate, must be replaced or repaired before the vehicle is placed in service.
(3) Motor vehicles used on roads not under the control of the state department of transportation, counties, or cities must be equipped with accessories necessary for a safe operation including:
(a) Operable head lamps;
(b) At least two tail lamps and brake lamps that emit a red light plainly visible from a distance of one thousand feet to the rear; and
(c) Two reflectors visible at night from three hundred fifty feet when directly in front of properly adjusted motor vehicle head lamps.
(4) The driver must do everything reasonably possible to keep the truck under control at all times and must not operate in excess of a speed at which the driver can stop the truck in one-half the visible distance.
(5) The area between the truck frame members, extending from the cab rearward as far as necessary to provide a safe work area, must be covered with suitable nonslip type material.
(6) Log trucks that have logs scaled at stations must have a platform on each side extending outward from the frame members at least eighteen inches, and must be eighteen inches long or as near to eighteen inches as the design of the truck permits. The treading surface of the platforms must be of nonslip material and the platform must be able to safely support a five hundred pound load.
(7) To protect the operator of vehicles from loads, there must be a substantial bulkhead behind the cab that extends up to the height of the cab.
(8) When at the dump or reload or where logs are scaled or branded on the truck, the logs must be scaled or branded before the binders are released.
(9) All vehicles, where vision of the operator in the direction of travel is impaired by the load or vehicle, must be moved only on a signal from a worker who has a clear view in the direction in which the vehicle is to be moved.
(10) Where a bridge or other roadway structure is posted with a load limit sign, log truck drivers or operators of other heavy equipment are prohibited from driving a load in excess of the posted limit over such a structure.
(11) All passengers must ride in the cab of the log truck.
(12) All trucks must keep to the right side of the road except where the road is plainly and adequately posted for left side travel.
(13) A method must be provided to ensure that the trailer will remain mounted on the truck while driving on highways or logging roads.
(14) When trucks are towed on any road, the person guiding the vehicle being towed must, by prearranged signals, govern the speed of travel. Vehicles must be towed at a reasonable speed and in a prudent manner. A tow cable or chain over fifteen feet in length must have a white flag attached at the approximate center, however, it is recommended that a rigid tow bar be used for this purpose.
(15) All rubber-tired motor vehicles must be equipped with fenders. Mud flaps may be used instead of fenders whenever the motor vehicle is not designed for fenders.
(16) All trucks must be equipped with doors with operable latches, or a safety bar or strap.
(17) Log trucks must not approach a landing while there is danger from incoming logs.
(18) While en route, the operator must check and tighten the wrappers/binders whenever there is reason to believe that the wrappers/binders have loosened or the load has shifted.
(19) Persons must not enter the area below a suspended load of logs.
(20) All trucks must be equipped with a means to protect the operator from inclement weather.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-58950 Log trucksWrappers and binders.
(1) On log trucks equipped with stakes, the following requirements must apply:
(a) In the hauling of a one log load, one wrapper chain or cable must be required and secured to the rear bunk. The log must be properly blocked or secured in a manner which will prevent it from rolling or shifting. An additional wrapper secured to the front bunk is optional.
(b) In the hauling of two log loads, not less than two wrapper chains or cables must be used to secure the load. The logs must be properly blocked to prevent them from rolling or shifting.
(c) On loads consisting of three or four logs not over forty-four feet in length, the load must be secured by not less than two properly spaced wrapper chains or cables. Ends of short logs not secured by such wrappers must be secured with extra wrappers. If any log is over forty-four feet in length, the load must be secured by not less than three properly spaced wrappers.
(d) Loads consisting of five or more logs((,)):
(i) When the logs are all seventeen feet or less in length, the load must be secured by not less than two properly spaced wrappers. ((Loads consisting of five or more logs, when any log is over seventeen feet in length, must be secured by not less than three properly spaced wrappers.))
(ii) When any log is over seventeen feet in length, the load must be secured by not less than three properly spaced wrappers. Log(s) loaded on top or in outside saddles of a load must not be transported unless secured by at least two wrapper chains or cables, one of which must be placed near each end of such log.
(2) On log trucks equipped with chock blocks the following requirements must apply:
(a) In the hauling of a one log load, one wrapper chain or cable shall be required and secured to the rear bunk and the log must be properly blocked in a manner to prevent it from rolling or shifting.
(b) One additional wrapper chain or cable shall be required on log trucks using chock blocks over and above the requirements in subsection (1)(c) and (d) of this section.
(3) In the case of short logs loaded crosswise, the following method of securing the load must be used if the truck or trailer is not provided with solid ends of a height sufficient to prevent any log in the load from rolling off:
Not less than two chock blocks must be used at each open end of the vehicle and the load must be held with at least two wrapper chains or cables. The wrappers must be firmly attached to the end of the truck or trailer. Rigid standards or stakes may be used in lieu of chock blocks but each such standard or stake must be either rigidly connected to the bed of the truck or trailer or must be placed in a tight-fitting socket at least 12 inches in depth. Other means furnishing equivalent security may be acceptable.
(4) When two wrappers are required, they must be applied within six feet of the front and rear bunks. When more than two wrappers are required, the front and back binder must be applied within six feet of the front and rear bunks.
(5) To properly secure short logs, binders must be placed near the end, not less than twelve inches from the end of the log.
(6) Log(s) loaded on top or in outside saddles of a load must not be transported unless secured by at least two wrapper chains or cables, one of which must be placed near each end of such log.
(7) All wrappers and binders must be fastened in place prior to tightening to prevent the displacement of logs on the top of the load.
(8) All wrapper chains or cables, except in the case of one log load, must entirely surround the load. This does not apply to gut-wrappers.
(9) Gut-wrappers, when used, must be adjusted so as to be tightened by, but not carry the weight of the logs above them.
(10) ((A warning must be given before throwing wrappers over the load and care must be taken to avoid striking other persons with the wrapper.)) Wrappers must not be thrown over the load until personnel are in the clear.
(11) Each log not contained within the stakes must be secured with at least two wrappers before the truck leaves the vicinity of the landing/loading area.
(12) While moving logs, poles, or log chunks within sorting or mill yards, that could roll or slide off the truck due to snow or ice conditions, or the logs or log chunks do not extend beyond the stakes, at least two wrappers and binders must be used regardless of the height of the load.
(13) Wrapper chains or cables, binders, fasteners, or attachments thereof, used for any purpose as required by these standards must have a minimum breaking strength of not less than fifteen thousand pounds and must be rigged so that it can be safely released.
Note:
3/8-inch hi-test steel chain, 7/16-inch improved plow steel wire rope of 6 x 19 or 6 x 37 construction, or materials having equivalent strength, when in compliance with the requirements herein contained, will be acceptable. (The diameter of the wire rope is immaterial as long as it meets the minimum breaking strength requirements.)
Note:
Nylon straps and ratchet binders having an equivalent breaking strength may be used when securing loads on (hay rack) log hauling systems.
(14) A loaded logging truck required to have wrappers by this section, may be moved within the loading area without wrappers only if such movement does not present a hazard to workers.
(15) For the purposes of this standard, applied bundle straps or banding are not acceptable as wrappers and binders.
(16) All loose ends of wrapper chains or cables must be securely fastened so as to prevent their swinging free in a manner that will create a hazard.
(17) Binders for securing wrappers on logging trucks must be fitted with hooks of proper size and design for the wrapper chain being used.
(18) Wrappers must be removed from service when any of the following conditions exist:
(a) Excessively worn links on chains;
(b) Deformed or stretched chain links;
(c) Cracked chain links; or
(d) Frayed, stranded, knotted, or otherwise defective wire rope.
(19) Pipe extension handles (swedes) for tightening or securing binders must be no longer than thirty-six inches. Care must be taken that a sufficient amount of the pipe extends over the binder handle.
(20) Defective binders must be immediately removed from service.
Note:
See Figures 25 through 35 for illustrations of placement and number of wrappers.
Placement and Number of Wrappers
One Log Load
 
Figure 25: One Log Load
Two Log Load
 
Figure 26: Two Log Load
Three or Four Log Load 44 Ft. or Less
 
Figure 27: Three or Four Log Load 44 feet or less
Three or Four Log Loads More Than 44 Feet
 
Figure 28: Three or Four Log Loads more than 44 feet
Five or Six Log Load All Logs 17 Feet or Less
 
Figure 29: Five or Six Log Load All Logs 17 feet or less
Seven or More Log Load All Logs 17 Feet or Less
 
Figure 30: Seven or More Log Load all Logs 17 feet or less
Five or More Log Load If Any Logs Are More Than 17 Feet
 
Figure 31: Five or More Log Load if any Logs are more than 17 feet
Proper Support for Logs
 
Figure 32: Proper Support for Logs
Outside Logs or Top Logs
 
Figure 33: Outside Logs or Top Logs
A Wrapper Must Be Near Each Bunk
 
Figure 34: A Wrapper must be near each bunk
Short Logs Loaded Crosswise
 
Figure 35: Short Logs Loaded Crosswise
Note:
All loads of logs on logging trucks equipped with chock blocks instead of stakes, must have at least one additional wrapper over and above the requirements for trucks equipped with stakes, except on one and two log loads and trucks with short logs loaded crosswise.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-591 Stationary log truck trailer loading.
(1) All loading devices must be designed, constructed and maintained so as to have a five to one safety factor for the rated load capacity.
(2) Loaders must be high and wide enough so they can safely load the maximum-sized trailers they are expected to handle without hanging up or striking the equipment.
(3) Electric-powered trailer loading devices must be equipped with a switch or device that will safely limit the upper direction of travel of the load line.
(4) Electric motors used for hoisting must be equipped with approved overload switches or breakers.
(5) Electrical switch controls must not exceed twenty-four volts. All control switches must be the momentary-contact type that require continuous manual pressure for the hoist to operate.
(6) Pendent control switches must be suspended by a chain or other suitable device that will prevent placing a strain on the electrical cable.
(7) Pendents must be installed so that the control switch does not touch the ground when retracted.
(8) All electrical equipment must be weatherproof-type or adequately protected from the weather, and must meet or exceed the requirements of the National Electrical Code as promulgated by the director of the department of labor and industries pursuant to RCW 19.28.060.
(9) Trailer loaders, except A-frames or bridge crane, must be equipped with reach guides or devices that will keep the reach in proper alignment. A tag rope or other safe guidance device must be used to guide trailers being loaded by an A-frame loader.
(10) Access roads and the area around the trailer loading devices must be kept free of standing water and debris and maintained in good repair.
(11) The maximum capacity load to be lifted must be posted in a conspicuous location where it can be easily seen by any person operating the hoist.
(12) Trailer loading equipment must be periodically inspected at least every thirty days and must be maintained in good repair. A written report must be made and signed by the person making the inspection and kept on file by the company for twelve months.
(13) ((The employer)) You must conduct an annual lifting test on each loading device and maintain a written record of the test.
(a) The written record must contain:
(()) (i) The date of the test;
(()) (ii) The name of person conducting the test;
(()) (iii) The amount of weight lifted; and
(()) (iv) The results kept in the office of the employer or at the site.
(b) The test weight must be at least one hundred twenty-five percent of the maximum rated load and a maximum of one hundred thirty percent of the maximum rated load.
(14) Each drum must be designed and arranged in such a manner that the line will maintain lead and spool evenly without chafing, crossing, or kinking.
(15) A braking system must be installed that has the ability to safely brake and hold one and one-half times weight of the full rated load.
(16) When trailers are to be loaded after dark, sufficient lights must be provided for a safe operation.
AMENDATORY SECTION (Amending WSR 06-07-142, filed 3/21/06, effective 5/1/06)
WAC 296-54-593 Log unloading, booms, and rafting groundsStorage and sorting areasGeneral.
(1) At least two persons must be present for all storing, sorting, or boom work, except for boomboat operations.
(2) Employees working on, over, or along water, where there is a danger of drowning, must be provided with and wear approved personal flotation devices.
(a) Employees are not considered exposed to the danger of drowning when:
(i) Employees work behind standard height and strength guardrails;
(ii) Employees work inside operating cabs or stations that will prevent accidentally falling into the water; or
(iii) Employees wear approved safety belts with lifeline attached to prevent falling into the water.
(b) Before and after each use, personal flotation devices must be inspected for defects that would reduce their designed effectiveness. Using a defective personal flotation device is prohibited.
(c) An approved personal flotation device must be approved by the United States Coast Guard as a Type I PFD, Type II PFD, Type III PFD, or Type V PFD, or their equivalent, as required in 46 C.F.R. 160 (Coast Guard Lifesaving Equipment Specifications) and 33 C.F.R. 175.23 (Coast Guard table of devices equivalent to personal flotation devices). Ski belt or inflatable personal flotation devices are prohibited.
(3) In operations where regular logging machinery, rigging, etc., is used, the applicable rules apply.
(4) ((The employer)) You must provide and ensure the use of artificial lights where employees work between the hours of sunset and sunrise. The lights must be located in a manner that will:
(()) (a) Be reasonably free of glare;
(()) (b) Provide uniform distribution of illumination; and
(()) (c) Avoid sharply defined shadows.
(5) On all log dumps, adequate power for the unloading method used must be provided. All machines used for hoisting, reloading, or lowering must be of an approved design and have enough power to control or hold the maximum load imposed in mid-air.
(6) Methods of unloading logs must be arranged and used in a manner to provide full protection to all employees.
(7) Binders must not be released from any load until an effective safeguard is provided.
(8) All mobile log handling machines must be equipped with a means to prevent the logs from accidentally leaving the forks, and it must be used.
(9) The operator of the unloading machine must have an unobstructed view of the unloading area or must make certain no one is in the area where the logs are to be unloaded. Rearview mirrors must be installed on mobile log handling equipment to assist the operator in determining that the area behind the machine is clear before backing up.
(10) Unloading lines must be arranged so that it is not necessary for an employee to attach them on the pond or dump side of the load.
(11) Life rings with a minimum of ninety feet of 1/4-inch line with a minimum breaking strength of five hundred pounds attached, must be provided at convenient points adjacent to water that is five feet or more in depth. Life rings must be a minimum of thirty inches outside diameter and seventeen inches inside diameter and be maintained so as to retain a thirty-two pound positive buoyancy.
AMENDATORY SECTION (Amending WSR 01-11-038, filed 5/9/01, effective 9/1/01)
WAC 296-54-59340 Log unloading, booms, and rafting grounds—Dry land sorting and storage.
(1) Unauthorized foot and vehicle traffic is prohibited in the sorting or storage area.
(2) Logs must be stored in a safe and orderly manner. Roadways and traffic lanes must be kept clear of protruding ends of logs and debris.
(3) Dry deck log storage areas must be kept orderly and maintained in a condition conducive to safe operation of mobile equipment. Roadways and walkways must have a smooth hard-packed surface wide enough to permit a safe operation. Bark, mud, and other debris must not be allowed to accumulate to the extent they constitute a hazard to the operation.
(4) ((The employer)) You must implement an effective method to control dust at log dumps and in sorting and storage areas.
(5) Only an authorized person ((shall)) will operate or ride any lift truck, log stacker, or log unloader.
(6) Signaling log unloader operators at dry deck areas by throwing bark or chips in the air is prohibited. Hand, horn signals or other safe, effective means must be used at all times.
(7) Unnecessary talking to the operator while operating controls of a log stacker or log unloader is prohibited.
(8) Lift forks and arms of unloading machines must be lowered to their lowest position, and all equipment brakes set before the operator leaves the machine unattended.
(9) Log unloaders or stackers must not be moved about the premises for distances greater than absolutely necessary with the lift extended above the driver's head or with loads lifted higher than is necessary for vision.
(10) When truck drivers are out of the cab, they must be in the clear, and in view of the log unloader before the lift forks are moved under the load and the lift is made.
(11) Where logs are offloaded onto a dry deck by unloading lines, a self-releasing mechanism must be used. Employees are prohibited from climbing dry decks to release unloading lines.
(12) Employees must not enter the hazardous area near or under loads of logs being lifted, moved, or suspended.
(13) When log unloaders and log stackers are designed so that logs being handled may jeopardize the safety of the operator, ((the employer)) you must provide overhead protection and any other necessary safeguards.
(14) Log unloaders and log stackers must be equipped with a horn or other audible warning device. If vision is impaired or restricted to the rear, the warning device must be sounded before operating the vehicle in reverse gear and periodically while backing. The warning device must be operative at all times.
(15) A limit stop, which will prevent the lift arms from over-traveling, must be installed on electric powered log unloaders.
(16) Shear guards must be installed on unloading machines and similar equipment on which the arms pivot and move alongside the operator creating a pinch point at that location.
(17) All forklift log handling machines must be equipped with a grapple arms and the arms must be used whenever logs are being carried.
(18) When log trucks are loaded by a log stacker and the lay of any log is higher than the stakes, the log stacker must remain against the completed load, or other suitable protection provided, to prevent the logs from falling until at least two wrappers and binders have been applied.
(19) All binders and wrappers must remain on the load until an approved safeguard has been provided to prevent logs from rolling off the side of the truck or trailer when binders are released. A shear log, or equivalent means, must be provided to ensure the log truck will be stationed close enough to the wrapper rack so that a log cannot fall between the log truck and the wrapper rack when removing binders and wrappers. At least one binder must remain secured while relocating or tightening other binders. Crotch lines, forklifts, log stackers, log unloaders, or other effective means must be used for this purpose.
(20) An extra wrapper or metal band of equal strength must be placed to hold the logs when it is necessary to remove a wrapper to prevent it from being fouled by the unloading machine.
(21) Machines with arms that block the regular exit when in the up position must have an emergency exit installed.
(22) Riding on any part of a log handling machine except under the canopy guard is prohibited.
(23) Identification tags must not be applied or pulled unless logs are resting in a stationary place, such as bunks, cradles, skids, or sorting tables.
(24) Employees must not approach the immediate vicinity of a forklift-type log handling machine without first notifying the operator of the person's intention and receiving an acknowledgement from the operator.
(25) When dry land log dumps use unloading methods similar to those of water dumps, the safety standards for water dumps apply.
(26) When logs are handled between sunset and sunrise or other periods of poor visibility, ((the employer)) you must provide illumination that meets the requirements of WAC 296-800-210 relating to illumination.
(27) Air operated stake releases must meet the following requirements:
(a) The air supply must be taken from the "wet" air reservoir or from the accessory air line to a spring loaded, normally closed control valve;
(b) The control valve must be located in the cab, positioned so that it is accessible only from the operator's position;
(c) The control valve must be fitted with a spring-loaded cover or otherwise guarded against inadvertent operation; and
(d) A separate air line must extend from the control valve to the tractor and trailer stake release chambers. The air line must be clearly identified or installed so that it cannot be mistaken for the service or emergency air line.
(28) Each deck must be constructed and located so it is stable and provides each employee with enough room to safely move and work in the area.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-601 Signals and signal systems.
(1) Standard hand or whistle signals as described in this chapter must be used for the movement of rigging, logs, or equipment when using a high lead, slackline, or cable skidder system for yarding. For hand signal illustrations, see appendix 1.
(2) Voice communication may be used to move rigging and control movement of logs, provided a standard audible whistle signal is sounded before any line is moved.
Note:
Subsections (1) and (2) of this section do not apply to grapple or other special yarding systems where employees are not exposed to the movement of logs or rigging.
(3) Voice communications may be used for grapple yarding under the following conditions:
(a) Voice communications by use of radio frequencies may be used to transmit instructions and directions to the yarder operator when using a grapple type logging system, if no employee is in a hazardous area near live rigging.
(b) Voice communication may be used to instruct the yarder operator when picking up an occasional log with the use of a choker on a grapple system, if the grapple is on the ground before the setting of the choker and no lines are moved by the operator until the person setting the choker has returned to a safe location away from any running lines. When a number of logs must be yarded by using chokers instead of the grapple, the requirements for high lead logging apply.
(4) Voice communication on the same radio frequencies used to transmit skyline, high-lead, slackline or skidder whistle signals (154.57 and 154.60 MHz channels), must be limited to reporting injuries, fire, and emergency situations where special tools or precautions are needed to prevent or alleviate a hazardous situation. In addition:
(a) The rigging crew must call the yarder engineer by name to ensure that proper contact is established;
(b) The yarder engineer must acknowledge the call with a whistle "stop" signal before the caller starts transmitting the voice message;
(c) Voice transmission must be kept as brief and to the point as possible; and
(d) After receiving the voice message, the yarder engineer must again acknowledge with a whistle "stop" signal that the message has been received and is clearly understood.
(5) If a standard signal is not listed for an unusual or new situation, a hand or whistle signal other than any listed for the type of yarding being done may be used for the specific situation only. Any special signals developed must be understood by all persons working in the area who may be affected by their use.
(6) A copy of the standard hand and whistle signals must be ((posted on the yarder and at places where crews congregate. For tractor logging operations, hand signals must be posted at places frequented by the crew members such as in crew buses, etc)) available at the worksite.
(7) Only one person in any crew ((shall)) must give signals at the point where chokers are being set. Any person is authorized to give a stop signal when someone is in danger or another emergency condition is apparent.
(8) Hand signals are permitted only when the signal person is in plain sight of the machine operator and when visibility allows signals to be seen. Hand signals may be used at any time as an emergency stop signal.
(9) Throwing of any type of material or relying on engine noise, such as from a chain saw, as a signal is prohibited.
(10) All persons must be in the clear before any signal is given to move the rigging, logs, or turns. Rigging, logs, or turns must not be moved until after the proper signals have been given.
(11) Machine operators must not move any line unless the signal received is clear and distinct. If in doubt, the operator must repeat the signal as understood and wait for confirmation.
(12) A horn or whistle that is automatically activated by the radio or electric signaling system must be used on each yarder used for skyline, high lead, skidder or slackline system of yarding, except where hand signals or voice communication as described in subsection (2) of this section is permitted. The horn or whistle must emit a sound that is clearly audible to all persons in the affected area and must be sounded before any line is moved. Such a horn or whistle is also required on combination yarding and loading machines and tree pullers. Audible signals are not necessary on grapple or other yarding systems where persons are not exposed to the movement of logs or rigging.
(13) All radio-controlled motorized carriages and skycars must have a warning horn which must be sounded before any lines or loads are moved or an audible whistle must be sounded from the yarder.
(14) Each unit of the signal or control system in use must be tested daily before logging operations begin. Audible signals used for test purposes must not include signals used for the movement of lines or materials.
(15) Citizen band (CB) radios must not be used to activate any signal, machine, or process, either automatically or by voice. CB radios may be used for communication between sides, vehicles, work units, or for emergency situations.
(16) When audible whistle signals are being used simultaneously by yarding and loading machines at a landing, signal whistle or horn tones used in connection with machine movements must be so differentiated as to distinctively identify any intended work movement of either machine.
(17) When the normal rigging crew configuration consists of two or more persons at the point where chokers are being set, ((they must each carry an operable transmitter on their person)) at least two members of the rigging crew must carry transmitters for each signal and control system being operated where chokers are being set. Only one transmitter for each signal and control system is required if:
(a) The signal person has no other duties and remains in an area where there are no hazards created by the moving rigging or logs; or
(b) The rigging crew is comprised of only one employee.
(18) The use of a jerk wire whistle system for any type of yarding operation is prohibited.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-604 Radio signaling permits.
To apply for a new radio signaling permit, to request a change in a permit, or to request a change in the use area for any permitted system, write to:
WISHA Services DivisionPermits
Department of Labor & Industries
P.O. Box ((44650)) 44655
Olympia, WA ((98504-4650)) 98504-4655
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-605 Radio systems used for voice communication, activation of audible signals, or control of equipment.
(1) A valid operating permit must be obtained by the owner from the department of labor and industries, prior to putting into use any radio signaling or control system intended to be used in conjunction with any type of cable logging operations.
(a) Permits will be issued only for systems licensed for such use and using those carrier frequencies as authorized by the Federal Communications Commission.
(b) Permits will be granted only when tone or function frequencies are compatible with other radio systems in use and when in compliance with all other applicable requirements of this chapter.
(2) The department of labor and industries reserves the right to designate the use of radio frequencies for specific purposes or functions. For example: Frequencies may be specified for voice transmission of instruction, others for tone-coded functions, or activation of signaling devices.
(a) Single tone coded functions must not be used on radio equipment designed to initiate whistle signals, or to activate or control any machine, material-handling device, or other equipment hazardous to employees.
(b) The department may also designate which tone frequencies may be used for the activation of a signaling device or for control of equipment on certain federal communication assigned carrier frequencies.
(3) A list of tone frequencies that may be used with any Federal Communications Commission assigned carrier frequencies will be made available from the department upon request.
(4) The department will assign the area or areas in which a radio signaling system may be used and mark those areas on the permit. Radio signaling systems must not be used in any area other than the ones indicated on the permit. (See Figure 36: Areas for Use of Radio Signaling Systems for Logging Operations.)
(5) The person or firm name on the permit must be the same as the person or firm operating the radio signaling system except for loaner or rental sets. A person or firm using a loaner or rental set is responsible for the radio signal system as if they were the owner of the set.
(6) The application for a permit to use a radio signaling system must contain the following information (see Figure 37: Application for permit to operate radio signal system in designated area):
(a) Name and address of applicant.
(b) The radio frequencies of the radio signaling device in MHz.
(c) The tone frequencies of the radio signaling system used to activate a horn, whistle, or control equipment in Hz. The security gate, or pulse tone, must be shown first.
(d) The name of the manufacturer of the radio signaling system.
(e) The serial number of the receiving unit.
(f) The state assigned area or location in which the unit will operate.
(g) The type of signaling used.
(h) From whom the system was purchased or acquired, and the date of acquisition of the system.
(i) Intended use and function of the system.
(7) All radio equipment must meet all applicable FCC standards. FCC identifier numbers and required information must be visible when possible.
(8) Radio equipment must not be used without displaying a permit as required by this standard. The permit must be prominently displayed on the outside case of the receiver of the unit or, for radio-controlled carriages, on the transmitter in the yarder.
(9) Each radio receiver must have its radio carrier frequency in MHz and tone frequency(s) in Hz indicated on the outside case of the receiver (see Figure 38: Radio permit):
(a) The manufacturer's name and serial number must be permanently indicated on the outside of the case;
(b) When the duration or width of the tone frequencies performs a function, the one duration/width must also be permanently indicated on the outside of the receiver case;
(c) Each transmitter must be identified with its receiver; and
(d) Two or more receivers in operation simultaneously on the same tone frequencies are prohibited unless one is used for monitoring only.
(10) It ((shall)) will be the responsibility of the owner of any radio signaling system to notify the department of labor and industries, immediately, if the signal system is:
(a) Permanently retired (in what manner and date retired);
(b) Sold (submit name and address of purchaser and date sold);
(c) Removed from the state (name of state to which moved and date moved); or
(d) Stolen (date).
(11) All radio signaling systems put into use for the first time after the effective date of these safety standards, ((shall)) must meet or exceed the minimum performance specifications contained in WAC 296-54-607 of these safety standards, and, when altered or repaired, ((shall)) must continue to meet such specifications.
(12) Adjustments, repairs, or alterations of radio signaling and control devices must be done only by or under the immediate supervision and responsibility of a qualified and certified radio technician with factory training or equivalent certified experience. Anyone without the technical ability or the proper equipment to cause the signaling systems to function within required tolerances must not attempt to repair, alter, or adjust the systems.
(13) When interference, overlap, fadeout, or blackout of radio signals is encountered, the use of the device must be discontinued immediately. Use may not be resumed until the source of trouble has been detected and corrected.
(14) Radio frequencies assigned to systems for which voice communications may be used to give signals to the yarder operator must not be the same frequencies as those assigned for whistle signals or machine control signals used in skyline, highlead, slackline, or cable skidder systems.
(15) When hazardous interference is created by moving a voice communication system into an area where a system is already in use on the same frequency, use of the ((newly-moved)) newly moved system must be immediately discontinued until the problem of interference has been corrected.
(16) Before moving any unit from one assigned geographical area to another (see area map, Figure 36: Areas for Use of Radio Signaling Systems for Logging Operations), the owner must apply for and receive a new permit from the department.
AREAS FOR USE OF RADIO SIGNALING SYSTEMS FOR LOGGING OPERATIONS
 
STATE OF WASHINGTON
DEPARTMENT OF LABOR AND INDUSTRIES
DIVISION OF INDUSTRIAL SAFETY AND HEALTH
Figure 36: Areas for Use of Radio Signaling Systems for Logging Operations
 
Figure 37: Application for Permit to Operate Radio Signal System in Designated Area
(( 
 
)) 
 
Figure 38: Radio Permit
A permit issued by the department of labor and industries shall be attached to the outside of the receiver which shall indicate the area in which the radio signaling equipment may be used.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-607 Radio signal systemsSpecifications and test procedures.
All radio-signaling systems put into use must meet or exceed the requirements of this section. When systems are altered or repaired they must continue to meet these requirements.
(1) Radio equipment in use at cable logging sites, which is primarily used for voice communication, must be on a separately assigned frequency from radio equipment primarily used to initiate whistles or other audible signaling devices or to control any machine, material handling device or other equipment hazardous to employees.
(2) Radio-signaling systems used to transmit whistle signals or control functions of equipment associated with skyline, highlead, slackline, or cable skidder systems of logging must transmit and decode only by the use of authorized multitone frequencies. Only sequential tones may be used to transmit signals or control equipment when using carrier frequencies of 154.57 or 154.60 MHz.
(3) All radio systems receiver sensitivity must be able to attain 0.4 microvolt, or greater, for 12 dB SINAD ratio for VHF frequencies and 0.5 microvolt, or greater, for UHF frequencies. When interference is a factor, the receiver may be desensitized in the furtherance of safety by a person qualified according to WAC 296-54-605(12).
(4) All radio signal systems must have receiver spurious attenuation of at least 70 dB when measured by the 20 db quieting method and image response attenuation of 60 db when measured by the 20 db quieting method. (("Spurious response attenuation" is a measure of the receiver's ability to discriminate between a desired signal to which it is resonant and an undesired signal at any other frequency to which it is also responsive.))
(5) All radio signal systems must have receiver selectivity of at least 80 db plus or minus 30 KHz, when measured by the E.*I.A. SINAD method.
(6) The receiver-decoder tone frequency stability must not exceed 0.006 (0.6%) above or below the assigned tone frequency.
(7) The drift of a transmitter-encoder tone must not exceed 0.006 (0.6%) above or below the assigned tone frequency.
(8) Parts of the radio-signaling system affected by moisture, which may be subjected to the entrance of moisture during use, must be weatherproofed. Transmitters must be tested within fifteen minutes after being subjected to the following conditions and must have the ability to continue functioning properly. The transmitter and receiver must be placed in a humidity chamber for eight hours where the humidity has been maintained at not less than ninety percent and where a 40 degrees C. temperature has been maintained.
(9) Radio-signaling system units must operate within tolerances specified at any temperature within the range of -30 degrees C. to +60 degrees C.
(10) Switches of transmitters used to send whistle signals or activate equipment associated with high lead, slackline, or cable skidder systems of logging must be designed so that two buttons, motions or a combination of these are required simultaneously to cause activation of the system. Arrangement of the activating switches must allow the operator to transmit signals easily but not easily activate a control or command function accidentally.
(11) All receivers intended to be mounted on or in the yarder or similar equipment, and all portable transmitters, must continue to maintain specified mechanical and electrical performance during and after being subjected to vibration of the magnitude and amplitude as follows:
(a) The equipment must be vibrated with simple harmonic motion having an amplitude of 0.015" (total excursion 0.03") with the frequency varied uniformly between 10 and 30 Hz and an amplitude of 0.0075" (total excursion 0.015") with the frequency varied uniformly between 30 and 60 Hz.
(b) The entire cycle of frequencies for each group (i.e., 10 to 30 cycles and 30 to 60 cycles) must be accomplished in five minutes and repeated three times.
(c) The above motion must be applied for a total of thirty minutes in each direction, that is, the directions parallel to both axes of the base and perpendicular to the plane of the base.
(12) All portable transmitters must be able to maintain specified mechanical and electrical performance after being subjected to a shock test as follows: The transmitter ((shall)) must be dropped five times from a height of four feet onto a smooth concrete floor. Each drop must impact a different surface of the transmitter.
(13) Transmitters operating on carrier frequencies of 154.57 MHz and on 154.60 MHz must be limited on maximum power output of 500 mW measured at the antenna terminals.
(14) To minimize the possibility of interference with other signaling systems, the input power of transmitters operating in the 450 MHz range should be limited to only the amount needed to transmit to the receiver of the system effectively.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-701 Wood spar trees.
(1) Wood spar trees must be of sound material of sufficient size and strength to withstand any stresses which may be imposed by any equipment used for that specific logging operation.
(2) The top of the tree must not extend ((not)) more than:
(a) Sixteen feet above the top guylines on spar trees over fifty feet tall; and
(b) Eight feet above the top guylines on spar trees less than fifty feet tall.
(3) School marms used as spar trees must be topped at the forks. Spar trees, except cedar, must be barked where guylines, straps, bull blocks, and tree plates are placed.
(4) Spar trees must be topped and limbs must be cut off close so that running lines will not foul or saw on protruding knots.
(5) At least four tree plates must be placed under top guylines on spar trees over fifty feet tall. At least three tree plates must be used on spar trees less than fifty feet tall.
(6) Tree plates must be equipped with lugs or other suitable means to hold them in place.
(7) Before raising spar trees, dummy trees must be topped and guyed with three guylines equivalent in breaking strength to the mainline.
(8) When spar trees are raised, stumps used for snubbing must be properly notched. Guylines must be held by a mechanical means. Snubbing by hand is prohibited.
(9) All rub trees must be limbed and topped.
(10) Loose material such as bark, spikes, straps or chains not in use and slabs caused by bumping logs or chafing straps must be removed from the spar trees. Heavy bark must be removed from trees used for a permanent installation.
(11) A person must ride only the passline to thread lines, to lubricate blocks, or to inspect rigging.
(12) When the friction lever and passline drum are on the opposite side of the machine from the operator, an experienced person ((must)) operates the friction lever while the engineer operates the throttle. While being used, the passline drum must be properly attended by another person to guide the passline onto the passline drum with a tool suitable for the purpose.
(13) Using a gypsy drum to handle employees in the tree is prohibited.
(14) A climber's rope must encircle the tree before the climber leaves the ground, except when the climber is riding the passline.
(15) Spikes, used by the climber as a temporary aid in hanging rigging, must be removed before the tree is used for logging.
(16) Topping trees in windy weather is prohibited.
(17) Topping, rigging-up, or stripping is prohibited when visibility is impaired.
(18) When heel tackle is fastened near the machine, a safety line must be placed in such manner that in case of breakage, lines do not strike the power unit and endanger the operator.
(19) Yarding with more than one unit on any one head spar is prohibited.
(20) The angle between the power unit, the high lead block, and the mainline road must not exceed a square lead on rigged spars. When using portable spars or towers, the location of the machine or position of the operator must ensure that the operator is not endangered by incoming logs.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-70110 Wood spar treesGuylines.
(1) Wood spar trees using a line greater than 7/8-inch and used as loading and yarding trees must have at least six top guys and four buckle guys, if a sail guy is used.
(2) Wood spar trees using a mainline greater than 7/8-inch and used only as yarding trees must have at least six top guys and must use at least three buckle guys.
(3) Wood spar trees using a mainline of 7/8-inch or less must be supported by at least five top guylines or other positive means of supporting the spar.
(4) Wood spar trees used for yarding with light equipment (7/8-inch or smaller mainline) must be guyed so that strains will be imposed on at least two guylines. If less than five top guys are used, guylines must be at least 1/4-inch larger than the mainline.
(5) Wood spar trees used for loading only with crotch line, spreader bar, or swinging boom must have at least four top guys and must use at least three buckle guys.
(6) More guylines must be added if there is any doubt about the stability of a spar tree, raised tree, tail tree, lift tree, or other equipment or rigging they support.
(7) Wood spar trees used for transfer must have at least five top guys and must use at least three buckle guys.
(8) Guylines must be alternately ((be)) passed around the wood spar in opposite directions to prevent twisting of the spar.
(9) Guylines must be attached to the upper portion of the wood spar by shackles.
(10) When a high lead block is hung below buckle guys, at least three top guys of equal strength to the mainline must be used to keep the top from swaying.
(11) When buckle guys are required, they must be installed on the tree where they will provide the maximum effectiveness.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-705 Truck and equipment maintenance shops.
It is recognized that the usual hazards encountered in maintenance shops performing work on logging and related equipment would be very similar to those found in general repair, machine or welding shops; therefore, the rules contained in chapter 296-24 WAC, General safety and health standards and other applicable safety standards promulgated and administered by the department of labor and industries ((shall)) must apply to such places of work.
AMENDATORY SECTION (Amending WSR 99-17-117, filed 8/18/99, effective 12/1/99)
WAC 296-54-99003 Appendix 2Sample minimum lockout/tagout procedure.
(Company Name) has established this lockout/tagout program to provide protection for employees performing maintenance or servicing of ((logging)) equipment.
Before any employee begins maintenance or servicing of equipment where the unexpected energizing, start up, or release of stored energy could cause injury, the equipment must be shut down, isolated from all potentially hazardous energy and locked or tagged out.
Employees must not start, attempt to start, energize or use equipment that has been locked or tagged out. Tags and/or padlocks will be provided for tagging and/or locking out ((logging)) machinery and will be durable enough to withstand the environment. Tags will contain a legend such as: "Do Not Start" or "Do Not Operate." When tagout is used, tags must be located in a position that will be obvious to anyone attempting to operate the machinery. In lockout, padlocks are commonly used to prevent access to ignition/master switches or battery disconnects.
Employees performing maintenance or servicing must determine which sources of hazardous energy must be disabled for a particular job. The following are examples of hazardous stored energy found on ((logging)) equipment:
(()) 1. Equipment
(()) 2. Hydraulic or pneumatic pressure
(()) 3. Mechanical (rotating saws, springs, shafts, gears, etc.)
(()) 4. Gravity (elevated blades, booms, grapples, saw heads, etc.)
Sample lockout/tagout procedures
The following steps must be followed for lockout/tagout:
(()) 1. Ensure that the brakes, swing locks, etc. are applied.
(()) 2. Place the transmission in the manufacturer's specified park position.
(()) 3. Lower or secure each moving element such as, but not limited to, blades, booms, grapples, buckets, saws, and shears to prevent a release of stored energy.
(()) 4. Shut down machinery, and ensure that a responsible person removes and keeps the ignition/master key.
(()) 5. Engage hydraulic safety locks when applicable.
(()) 6. Before working on hydraulic or air systems, relieve pressure by bleeding tanks or lines and operate controls to dissipate residual stored energy (pressure).
(()) 7. Place lockout and/or tagout device.
Before lockout or tagout devices are removed and machinery is started, inspect the work area to ensure all tools have been removed, guards are replaced, and employees are in the clear.
We will provide training to ensure that the purpose and function of the lockout/tagout program are understood by employees performing maintenance or repair of equipment.
NEW SECTION
WAC 296-54-99015 Appendix 6Sample chain shot training program.
"Chain Shot" Awareness and Prevention Training
 
Employee _____
Trainer _____
Date _____
 
All employees who operate or work around or perform maintenance and/or repair of any kind of machinery equipped with a hydraulic powered bar saw must receive "chain shot" awareness training appropriate to their job.
Note: Employers who have employees who are potentially exposed to the chain shot but do not operate, inspect, or maintain the equipment can limit training to the information in Section 1.
□ Indicates that the employee has received training.
□ Section 1 General information
• Chain shot is the high velocity separation and ejection of a piece or pieces of cutting chain from the end of a broken chain in mechanized timber harvesting/processing. Chain shot exposes both machine operators and bystanders to a risk of serious injury or death. Chain shot typically occurs near the drive end of the cutting system but can also come from the bar tip area.
• A chain shot consists of two breaks in a chain. First, the loop of chain breaks and forms two ends. One end moves past the drive sprocket or bar nose and is rapidly accelerated due to a whip-like motion of the chain end. The "whip action" causes the second break releasing small parts at extremely high speed.
• The "shot cone zone" is the area along the plane of the guide bar where pieces of a broken chain usually travel unless pieces are deflected. The SCZ angles out approximately at a 15 degree angle on both sides of the guide bar and a distance that possibly exceeds 230 feet.
• Employees should stay clear of the shot cone zone.
 
□ Section 2 Cutting system inspection
The cutting system must be inspected before initial use during each work shift. Defective parts that would make the cutting system unsafe to operate, must be replaced or repaired before the cutting system is placed in service. Report unsafe conditions to your supervisor.
Inspections must include:
• The lubrication system for leaks or damage.
• The chain for cracks or worn/damaged parts.
• The bar for wear and straightness and ensure the tip is properly secured.
• The sprocket.
• The chain catcher if equipped.
• The chain shot guard if equipped.
□ Section 3 Cutting system maintenance
• Sharpen, assemble and repair chains in accordance with the manufacturer's specifications.
• Maintain proper bar and chain lubrication, making sure to use the right type and amount of lubricant.
• Replace the drive sprocket when it has excessivewear.
• Clean guide bar grooves and oil port holes regularly.
• Guidebars should be flipped regularly to ensure even wear.
□ Section 4 Cutting system operation
• The operator and other persons should be kept clear of the shot cone zone.
• Follow chain manufacturer's recommendations for chain speed. "Boosting" or exceeding the recommended chain speed is prohibited.
• Maintain proper chain tension.
REPEALER
The following sections of the Washington Administrative Code are repealed:
WAC 296-54-595
Transporting crews.
WAC 296-54-59510
Speeders used to transport crews.
WAC 296-54-59520
Trailers used to transport crews.
WAC 296-54-597
Railroads.
WAC 296-54-59710
Railroad construction and maintenance.
WAC 296-54-59720
Railroad operations.
WAC 296-54-59730
Railroad maintenance—Loading or unloading.